Creep property research of new martensite heat-resistant steel G115

G115 steel was jointly developed by China Iron & Steel Research Institute Group Co.,Ltd.and Baosteel for usage in 600-650 ℃ ultrasupercritical boiler tubes.Using a hot extruded G115 tube,creep tests were conducted under a constant stress of 130 MPa and temperatures of 625,650 and 675 ℃.Comparing creep curves under different temperatures,it is observed that the creep performance of a G115 tube is more sensitive to temperature than stress.Steady-state creep rates of creep specimens are significantly increased by enhancing the temperature.A micro-structural analysis of ruptured creep specimens under a stress of 130 MPa and temperatures of 650 ℃ and 675 ℃ was performed;the fracture mechanism of creep specimens under these two temperatures mainly included the appearance of creep holes on the grain boundary and a decrease in the martensite lath density.

Triaxial creep tests of weak sandstone from fracture zone of high dam foundation

The lithology of fracture zone which was developed at the dam foundation of a hydropower station is weak sandstone with poor integrity and pore cementation contact.Its creep properties have a significant impact on the deformation and stability of the dam.Based on the characteristics of loose organizational structure,high moisture content and poor mechanical properties,the triaxial compression tests and creep tests were carried out,respectively.The results show significant non-linear,low strength and no obvious strength peaks.Both axial and lateral strains are achieved more than 3%when the tests are failed.The weak sandstone has a significant creep property,but only transient and steady state appear under low stress.Increased stress causes creep intensified and lateral strain gradually exceeds axial strain.In the failure stage,it has characteristics of large axial plastic deformation,obvious volumetric ductility dilation and large steady creep rate.The accelerated creep appears shortly after transient loading under confining of pressures 1.0 MPa and 1.5 MPa.Therefore,an improved Burgers creep model considering the non-linear characteristics of weak sandstone is built based on hyperbolic equation and the creep parameters are identified.This model can well describe the creep properties of weak sandstone.

Temperature-controlled triaxial compression/creep test device for thermodynamic properties of soft sedimentary rock and corresponding theoretical prediction

In deep geological disposal of high-level nuclear waste,one of the most important subjects is to estimate long-term stability and strength of host rock under high temperature conditions caused by radioactive decay of the waste.In this paper,some experimental researches on the thermo-mechanical characteristics of soft sedimentary rock have been presented.For this reason,a new temperature-controlled triaxial compression and creep test device,operated automatically by a computer-controlled system,whose control software has been developed by the authors,was developed to conduct the thermo-mechanical tests in different thermal loading paths,including an isothermal path.The new device is proved to be able to conduct typical thermo-mechanical element tests for soft rock.The test device and the related testing method were introduced in detail.Finally,some test results have been simulated with a thermo-elasto-viscoplastic model that was also developed by the authors.

Dynamic stress accumulation model of granite residual soil under cyclic loading based on small-size creep tests

The creep behaviors of granite residual soil with pre-stress of 100 kPa was investigated by a series of small size creep tests. Three different types of strain curves were obtained at different stress levels. Based on creep characteristics of the granite residual soil under different stress levels, a creep model of the granite residual soil was established by rheological theory, and related parameters of the model were determined according to the experimental data at the same time. Further on, based on the established creep model, a theoretical model of dynamic stress accumulation in the granite residual soil under cyclic loading was deduced. It is found that there is a threshold of dynamic stress accumulation in this theoretical model. The dynamic stress accumulation laws of the granite residual soil are different under different cyclic loading stress. Finally, with the dynamic stress accumulation laws in the small-size samples of granite residual soil under different cycle loading studied and the experimental results comparing with the theoretical results, it verifies the validity of the theoretical model.

A POTENTIAL METHOD FOR DETERMINING THE HAZ PROPERTIES IN WELDS USING TWO-MATERIAL IMPRESSION CREEP TEST

The results of a theoretical and finite element (FE) investigation of a two-material impression creep test method, using a rectangular indenter, are presented. The method uses a general formulation for steady-state creep deformation for multi-material components in conjunction with the results of FE analyses. The practical application of the proposed technique, in determining the secondary creep properties of heat-affected zone (HAZ) materials in welds, for which conventional creep testing methods cannot be used, is considered. A number of numerical examples are used to describe solution procedures and to verify the method.

Computer Simulation of the Indentation Creep Tests on Particle-Reinforced Composites

A systematical simulation has been carried out on the indentation creep test on particle-reinforced composites. The deformation, failure mechanisms and life are analyzed by three reasonable models. The following five factors have been considered simultaneously: creep property of the particle, creep property of the matrix, the shape of the particle, the volume fraction of the particle and the size (relative size to the particle) of the indentation indenter. For all the cases, the power law respecting to the applied stress can be used to model the steady indentation creep depth rate of the indenter, and the detail expressions have been presented. The computer simulation precision is analyzed by the two-phase model and the three-phase model. Two places of the stress concentration are found in the composites. One is ahead of the indentation indenter, where the high stress state is deduced by the edge of the indenter and will decrease rapidly near to a steady value with the creep time. The other one is at the interface, where the high stress state is deduced by the misfit of material properties between the particles and matrix. It has been found that the creep dissipation energy density other than a stress parameter can be used to be the criterion to model the debonding of the interfaces. With the criterion of the critical creep dissipation energy density, a power law to the applied stress with negative exponent can be used to model the failure life deduced by the debonding of interfaces. The influences of the shape of the particles and the matching of creep properties of particle and matrix can be discussed for the failure. With a crack model, the further growth of interface crack is analyzed, and some important experimental phenomena can be predicted. The failure mechanism which the particle will be punched into matrix has been also discussed. The critical differences between the creep properties of the particles and matrix have been calculated, after a parameter has been defined. In the view of competition of failure mechanisms, the best matching of the creep properties of the two phases and the best shape of the particles are discussed for the composite design.

DETERMINATION OF CREEP PROPERTIES OF THERMAL BARRIER COATING(TBC)SYSTEMS FROM THE INDENTATION CREEP TESTING WITH ROUND FLAT INDENTERS

Indentation creep behavior with cylindrical flat indenters on the thermal barrier coating (TBC) was studied by finite element method (FEM). On ike constant applied indentation creep stress, there is a steady creep rate for each case studied for different creep properties of the TBC system. The steady creep depth rate depends on the applied indentation creep stress and size of the indenters as well as the creep properties of the bond coat of the TBC and the substrate. The possibilities to determine the creep properties of a thermal barrier system from indention creep testing were discussed. As an example, with two different size indenters, the creep properties of bond coat of the TBC system can be derived by an inverse FEM method. This study not only provides a numerical method to obtain the creep properties of the TBC system, but also extends the application of indentation creep method with cylindrical flat indenters.

High temperature creep property of silicon particles reinforced high Al Zn based alloys

The deformation creep characteristics of as cast silicon particles reinforced zinc based alloys (Si/ZA27) were determined by high temperature creep experiments at 453 K and 61.1 MPa condition. The experimental results indicated that the minimum creep rate of the silicon containing alloys are about three fifth of that of the matrix alloy(ZA27). The deformation process is mainly controlled by grain boundary sliding mechanism. Both dislocation climb and disperse silicon phase are also contributed to it. Micro structural changes were investigated during the deformation experiments.

The Correlation between Density and Low-Temperature Creep Property of Asphalt

The density of asphalt was measured with the pycnometer and densitometer. Creep properties of the asphalt were investigated with the bending beam rheometer at temperatures ranging from 0 ~C to -36 ~C. The asphalt density data used to correlate with the creep properties were calculated from the regression equation of density and temperature. The asphalt sample used to determine the creep property was aged by the standard RTFOT test and the PAV test. The test results showed that the asphalt density had a linear relationship with temperature changes. The logarithm of the creep stiffness and the slope of the logarithm of the stiffness at 60 seconds all demonstrated a linear relationship with the density, and the regression coefficient of these data was around 0.99. The creep stiffness and the slope of the creep stiffness can be calculated from the asphalt density at the same temperature.

Creep property and microstructural evolution of DD11 alloy under high temperature and low stress

In this paper,the interrupted and ruptured creep tests were carried out in a novel second generation single crystal superalloy named DD11 at 1100℃/130 MPa.The alloy exhibited typical creep curve including primary,steady,and tertiary three creep stages.The microstructural evolution at different stages of the creep were analyzed by scanning electron microscopy(SEM)and transmission electron microscopy(TEM).The results show that theγ′phases transform into rafted structure at the early stage of the steady creep and keep stable during the steady creep stage.As the creep goes on,the rafted structure further coarsens and the topological inversion occurs.In addition,at the primary creep,the dislocations mainly move in theγmatrix and pile up in theγ/γ′interface since the matrix channels widen slightly.The formation of the regular interfacial dislocation networks occurs at the early stage of the steady creep.Under the low stress,the dominated deformation mechanism during steady creep stage is the climbing of the〈010〉type edge dislocation.Furthermore,the effect of the deformation mechanism on creep property was discussed in detail.

Creep Property of Solidifying Backfill Body of High-Water Material

On the basis of the creep test of bigh-water materisl solidifying backfill body(abb. HW body), This paper discusses its creep properties- The visco-elasto-plastic model, which shows the creep properties of HW body, is developed, and the creep contitutive equations are deduced. The visco-elastoplastic model is proved by the experiments and practice.

Microstructural evolution of Mg-14Gd-0.4Zr alloy during compressive creep

The present work reports the creep behavior and microstructural evolution of the sand-cast Mg-14Gd-0.4Zr alloy(wt.%) prepared by the differential pressure casting machine. Their compressive creep tests at 250 ℃ were performed under various applied stresses(i.e., 60, 80 and100 MPa). Among them, the sand-cast Mg-14Gd-0.4Zr samples examined under 250 ℃/80 MPa for 39 and 95 h, respectively, were chosen to systemically analyze their creep mechanisms using high-angle annular dark field-scanning transmission electron microscopy(HAADF-STEM).The obtained results showed that the enhancement of creep resistance can be mainly attributed to the coherent β' and β'_F phases with an alternate distribution, effectively impeding the basal dislocations movement. However, with the creep time increasing, the fine β'+β'_F precipitate chains coarsened and transformed to semi-coherent β_1 phase and even to large incoherent β phase(surrounded by precipitate-free areas) in grain interiors. The precipitate-free zones(PFZs) at grain boundaries(GBs) were formed, and they could expand during creep deformation. Apart from the main cross-slip of basal and prismatic dislocations, type dislocations were activated and tended to distribute near the GBs. The aforementioned phenomena induced the stress concentrations, consequently leading to the increment of the creep strain.

Effects of rejuvenation heat treatment on microstructure and creep property of a Ni-based single crystal superalloy

Both surface and internal microstructures of a second-generation Ni-based single crystal(SX) superalloy were studied after creep and rejuvenation heat treatment(RHT).It is indicated that the microstructures,such as the dislocation network,the γ phase and the γ' phase,can be recovered to those after the standard heat treatment(SHT).It is found that RHT affected zone(RAZ) formed at the surface is composed of theγ'-free layer,the transition layer and the recrystallization(RX),which are less than 20 μm in depth totally.Such depth of the RAZ doesn't affect the properties of the superalloy.The morphology of γ' phase at the RAZ is related to the composition of the elements.The average creep life after RHT is close to the average life after SHT.It is concluded that RHT could effectively repair SX parts and increase the total life of the sample after a damage by creep.

Microstructural evolution and restoration of creep property for a damaged K403 alloy after rejuvenation heat treatments

Rejuvenation heat treatments can restore the microstructures and mechanical properties of the degraded turbine blades in gas turbine engines.Herein we analyze the effects of rejuvenation heat treatments on the microstructural characteristics and mechanical properties of damaged and undamaged specimens of a Ni-based superalloy,K403.The damaged specimens were found to have degraded microstructures and shorter creep lifetime than the undamaged specimen.The rejuvenation heat treatment proved beneficial,especially for specimens exposed to damage for 50 h.In addition,the microstructure recovery and creep life were found to depend on the predamage durations of the specimens.A y’-precipitate-based creep lifetime model was established to predict the residual lifetime based on the microstructural information.

Aging Coefficient, Creep Coefficient and Extrapolating Aging Coefficient from Short Term Test for Sealed Concrete

Aging coefficient and creep coefficient are important parameters for creep analysis of any structure. With the aim to obtain those parameters, an experimental investigation is carried out on sealed concrete. Altogether ten specimens were tested, out of which four were for creep, two for shrinkage and remaining four for relaxation test. A year of relaxation test and two years of creep test results were analyzed to compute aging coefficient and creep coefficient. From regression analysis of observed and calculated aging coefficient using formula of Bazant and Kim, modification for aging coefficient is performed and extrapolation equations are generated. Instead of ACI model, B3 model has been used to obtain compliance function as the parameters of B3 model seems more relevant to creep mechanism of concrete compared to that of ACI model.

Magnesium-based nanocomposites:A review from mechanical,creep and fatigue properties

The addition of nanoscale additions to magnesium(Mg)based alloys can boost mechanical characteristics without noticeably decreasing ductility.Since Mg is the lightest structural material,the Mg-based nanocomposites(NCs)with improved mechanical properties are appealing materials for lightweight structural applications.In contrast to conventional Mg-based composites,the incorporation of nano-sized reinforcing particles noticeably boosts the strength of Mg-based nanocomposites without significantly reducing the formability.The present article reviews Mg-based metal matrix nanocomposites(MMNCs)with metallic and ceramic additions,fabricated via both solid-based(sintering and powder metallurgy)and liquid-based(disintegrated melt deposition)technologies.It also reviews strengthening models and mechanisms that have been proposed to explain the improved mechanical characteristics of Mg-based alloys and nanocomposites.Further,synergistic strengthening mecha-nisms in Mg matrix nanocomposites and the dominant equations for quantitatively predicting mechanical properties are provided.Furthermore,this study offers an overview of the creep and fatigue behavior of Mg-based alloys and nanocomposites using both traditional(uniaxial)and depth-sensing indentation techniques.The potential applications of magnesium-based alloys and nanocomposites are also surveyed.

Tailoring the microstructural characteristics and enhancing creep properties of as-cast Mg-5Bi-5Sn alloy through Mn addition

The creep properties, microstructural characteristics and creep mechanisms of as-cast Mg-5Bi-5Sn(BT55) alloy without and with Mn(BTM550) addition were investigated via creep at 423, 448, and 473 K as well as stresses of 30, 50 and 75 MPa. The results indicate that adding Mn can result in the formation of primary and the dynamic precipitated α-Mn phases. In addition, the morphology of the precipitated Mg_(3)Bi_(2) phase and the orientation relationship between Mg_(2)Sn precipitates and α-Mg can be effectively modified. Tailoring the microstructural characteristics is responsible for the improved creep performance of BTM550 alloy. The dominant creep mechanisms in BT55 and BTM550 alloys are dislocation cross-slip and climb, respectively. Furthermore, twinning and pyramidal slip play an assisting part in both alloys during creep process.

Creep properties and permeability evolution in triaxial rheological tests of hard rock in dam foundation

Triaxial creep tests were carried out under seepage pressure by using rock servo-controlled triaxial rheology testing equipment. Based on experimental results, rock rheological properties influenced by seepage-stress coupling were studied, and variations of seepage rate with time in complete creep processes of rock were analyzed. It is shown that, when the applied stress is less than failure stress level, the creep deformation is not obvious, and its main form is steady-state creep. When applied stress level is greater than or less than but close to fracture stress, it is easier to see the increase of creep deformation and the more obvious accelerative creep characteristics. The circumferential creep deformation is obviously higher than the axial creep deformation. At the stage of steady-state creep, the average of seepage flow rate is about 4.7×10-9 rn/s at confining pressure （tr3） of 2 MPa, and is about 3.9×10-9 m/s at a3 of 6 MPa. It is seen that the seepage flow rate at or3 of 2 MPa in this case is obviously larger than that at tr3 of 6 MPa. At the stage of creep acceleration, the seepage flow rate is markedly increased with the increase of time. The variation of rock permeability is directly connected to the growth and evolution of creep crack. It is suggested that the permeability coefficient in complete creep processes of rock is not a constant, but is a function of rock creep strain, confining pressure, damage variable and pore water pressure. The results can be considered to provide a reliable reference for the establishment of rock rheological model and parameter identification.

Fractional description of mechanical property evolution of soft soils during creep

The motion of pore water directly influences mechanical properties of soils, which are variable during creep. Accurate description of the evolution of mechanical properties of soils can help to reveal the internal behavior of pore water. Based on the idea of using the fractional order to reflect mechanical properties of soils, a fractional creep model is proposed by introducing a variable-order fractional operator, and realized on a series of creep responses in soft soils. A comparative analysis illustrates that the evolution of mechanical properties, shown through the simulated results, exactly corresponds to the motion of pore water and the solid skeleton. This demonstrates that the proposed variable-order fractional model can be employed to characterize the evolution of mechanical properties of and the pore water motion in soft soils during creep. It is observed that the fractional order from the proposed model is related to the dissipation rate of pore water pressure.

Influence of recycled carbon fiber addition on the microstructure and creep response of extruded AZ91 magnesium alloy

In this study,the recycled short carbon fiber(CF)-reinforced magnesium matrix composites were fabricated using a combination of stir casting and hot extrusion.The objective was to investigate the impact of CF content(2.5 and 5.0 wt.%)and fiber length(100 and 500μm)on the microstructure,mechanical properties,and creep behavior of AZ91 alloy matrix.The microstructural analysis revealed that the CFs aligned in the extrusion direction resulted in grain and intermetallic refinement within the alloy.In comparison to the unreinforced AZ91 alloy,the composites with 2.5 wt.%CF exhibited an increase in hardness by 16-20%and yield strength by 5-15%,depending on the fiber length,while experiencing a reduction in ductility.When the reinforcement content was increased from 2.5 to 5.0 wt.%,strength values exhibited fluctuations and decline,accompanied by decreased ductility.These divergent outcomes were discussed in relation to fiber length,clustering tendency due to higher reinforcement content,and the presence of interfacial products with micro-cracks at the CF-matrix interface.Tensile creep tests indicated that CFs did not enhance the creep resistance of extruded AZ91 alloy,suggesting that grain boundary sliding is likely the dominant deformation mechanism during creep.