Novel Optimized Cross-Layer Design with Maximum Weighted Capacity Based Resource Allocation for AMC/HARQ Wireless Networks

To provide quality-of service (QoS) guarantees for heterogeneous applications, most recent wireless communications technologies and standards combine the error-correcting capability of hybrid automatic repeat request (HARQ) schemes at the data link layer (DLL) with the adaptation ability of the adaptive modulation and coding (AMC) modes at the physical layer (PHY) layer. This paper aims to investigate the aggregated system capacity as well as the breakdown of this capacity for different ACM modes in each HARQ scheme. This investigation was done by using maximum weighted capacity (MWC) resource allocation at the PHY layer in conjunction with a novel packet error rate (PER)-based scheduling at the medium access control (MAC) layer. As a result, the dominant AMC mode corresponding to channel SNR was available.

Cross-Layer Design Based Optimized Link State Routing Protocol for Wireless Mesh Networks

A proactive routing protocol CL-OLSR （cross-layer based optimized link state routing） by using a brand-new routing metric CLM （cross-layer metric） is proposed. CL-OLSR takes into account four link quality impact factors in route calculation through the cross-layer operation mechanism： the node available bandwidth, the node load, the link delivery rate, and the link interference, and thus the effect of route selection is optimized greatly. The simulation results show that the proposed CL-OLSR protocol can not only improve the network throughput to a large extent, but also reduce the end-to-end delay, while achieving load balance route results.

Cross-layer design of combining AMC with HARQ in cooperative relay system with perfect and imperfect CSI

A cross-layer design which combines adaptive modulation and coding (AMC) at the physical layer with a hybrid automatic repeat request (HARQ) protocol at the data link layer (LL) is presented, in cooperative relay system over Nakagami-m fading channels with perfect and imperfect channel state information (CSI). In order to maximize spectral efficiency (SE) under delay and packet error rate (PER) performance constraints, a state transition model and an optimization framework with perfect CSI are presented. Then the framework is extended to cooperative relay system with imperfect CSI. The numerical results show that the scheme can achieve maximum SE while satisfying transmitting delay requirements. Compared with the imperfect CSI, the average PER with perfect CSI is much lower and the spectral efficiency is much higher.

Performance of Cross-Layer Design with Power Allocation in Space-Time Coded MIMO Systems

A cross-layer design(CLD)scheme with combination of power allocation,adaptive modulation(AM)and automatic repeat request(ARQ)is presented for space-time coded MIMO system under imperfect feedback,and the corresponding system performance is investigated in a Rayleigh fading channel.Based on imperfect feedback information,a suboptimal power allocation(PA)scheme is derived to maximize the average spectral efficiency(SE)of the system.The scheme is based on a so-called compressed SNR criterion,and has a closed-form expression for positive power allocation,thus being computationally efficient.Moreover,it can improve SE of the presented CLD.Besides,due to better approximation,it obtains the performance close to the existing optimal approach which requires numerical search.Simulation results show that the proposed CLD with PA can achieve higher SE than the conventional CLD with equal power allocation scheme,and has almost the same performance as CLD with optimal PA.However,it has lower calculation complexity.

On Cross-Layer Design of AMC Based on Rate Compatible Punctured Turbo Codes

This paper extends the work on cross-layer design which combines adaptive modulation and coding at the physical layer and hybrid automatic repeat request protocol at the data link layer. By contrast with previous works on this topic, the present development and the performance analysis as well, is based on rate compatible punctured turbo codes. Rate compatibility provides incremental redundancy in transmission of parity bits for error correction at the data link layer. Turbo coding and iterative decoding gives lower packet error rate values in low signal-to-noise ratio regions of the adaptive modulation and coding (AMC) schemes. Thus, the applied cross-layer design results in AMC schemes can achieve better spectral efficiency than convolutional one while it retains the QoS requirements at the application layer. Numerical results in terms of spectral efficiency for both turbo and convolutional rate compatible punctured codes are presented. For a more comprehensive presentation, the performance of rate compatible LDPC is contrasted with turbo case as well as the performance complexity is discussed for each of the above codes.

A CROSS-LAYER STRATEGY FOR COOPERATIVE DIVERSITY IN WIRELESS SENSOR NETWORKS

We investigate the problem of how to minimize the energy consumption in multi-hop Wireless Sensor Network (WSN),under the constraint of end-to-end reliability Quality of Seervice (QoS) requirement.Based on the investigation,we jointly consider the routing,relay selection and power allocation algorithm,and present a novel distributed cross-layer strategy using opportunistic relaying scheme for cooperative communication.The results show that under the same QoS requirement,the proposed cross-layer strategy performs better than other cross-layer cooperative communication algorithms in energy efficiency.We also investigated the impact of several parameters on the energy efficiency of the cooperative communication in WSNs,thus can be used to provide guidelines to decide when and how to apply cooperation for a given setup.

An Energy-Efficient Access Control Algorithm with Cross-Layer Optimization in Wireless Sensor Networks

This paper presents a wireless sensor network (WSN) access control algorithm designed to minimize WSN node energy consumption. Based on slotted ALOHA protocol, this algorithm incorporates the power control of physical layer, the transmitting probability of medium access control (MAC) layer, and the automatic repeat request (ARQ) of link layer. In this algorithm, a cross-layer optimization is preformed to minimizing the energy consuming per bit. Through theory deducing, the transmitting probability and transmitting power level is determined, and the relationship between energy consuming per bit and throughput per node is provided. Analytical results show that the cross-layer algorithm results in a significant energy savings relative to layered design subject to the same throughput per node, and the energy saving is extraordinary in the low throughput region.

Cross-layer Enhancement to Multi-hop Routing in Sensor Networks: an Empirical Study

Lossy link is one of the unique characteristics in random-deployed sensor networks. We envision that robustness and reliability of routing cannot be ensured purely in network layer. Our idea is to enhance the performance of routing protocol by cross-layer interaction. We modified mint protocol, a routing protocol in TinyOS and proposed an enhanced version of mint called PA-mint. A transmission power control interface is added to network layer in PA-mint. When routing performance of the current network is not satisfied, PA-mint monotonically increases the transmission power via the interface we added. PA-mint is able to connect orphan nodes and robust to node mobility or key nodes failure. In the case that automatic request retransmission is employed, the number of retransmissions can be reduced by PA-mint. Results from experiments show that PA-mint increases the reliability and robustness of routing protocol by cross-layer interaction.

Energy-Efficient Cross-Layer Optimization for Wireless Sensor Networks

In this paper, we propose a cross-layer design combining adaptive modulation coding (AMC) and automatic repeat request (ARQ) to minimize the bit energy consumption under both packet loss rate and retransmission delay constraints. We analyze the best constellation size of M-ary square quadrature amplitude modulation (MQAM) in different distance, and give advice on retransmission limits under different packet loss rates. The impacts of path loss fading and additive white Gaussian noise (AWGN)are taken into consideration. The computation of energy consumption includes the circuit, transmission and retransmission energies at both transmitter and receiver sides. Numerical results are obtained to verify the validity of our design. We also show that the retransmission benefit varies with the packet loss rate constraint.

Performance Study of a Cross-Layer Based Multipath Routing Protocol for IEEE 802.11e Mobile Ad Hoc Networks

Communication over wireless links identifies significant challenges for routing protocols operating. This paper proposes a Cross-layer design based Multipath Routing Protocol (CMRP) for mobile ad hoc networks, by means of the node energy signal from the physical layer. The purpose is to optimize routing decision and path quality. The nodes’ mobility behavior is predicted using a notion of “Signal Fading Degree, SFD”. Especially, in combination of the IEEE 802.11e standard at the MAC layer, we determine that the IEEE 802.11e makes a significant contribution to performance improvement of CMRP. Performance evaluation of AODV in legacy 802.11 and CMRP in IEEE 802.11e shows that, as a function of speed of node mobility, a tremendous reduction achieved, in metrics such as the average end-to-end delay, route overhead, route discovery frequency, normalized routing load - almost more than 80%, 40%, 40%, and 40%. In the case of varying number of sessions, the reduction for route discovery frequency and normalized routing load are up to 70% and 80%.

Proposal for a cross layer scheme for real-time wireless video

This paper focuses on the design of the cross layer between the video application layer and the MIMO physical layer. MIMO physical layer research has promised an enormous increase in the capacity of wireless communication systems. Also MIMO wireless systems operate under fading conditions where the channel faces arbitrary fluctuations. Since the wireless channel changes over each coherence period, the capacity of the wireless channel, given the power constraints, changes. Hence to make efficient use of the available capacity one needs to adapt the video bit rate. However it is impossible to adapt at the application layer as changing the parameters of the video takes more time than the coherence period of the channel. In this paper we address this problem through a novel solution and also investigate its performance through a simulation study.

Cross Layer Design for Cooperative Transmission in Wireless Sensor Networks

Several protocols and schemes have been proposed to reduce energy consumption in Wireless Sensor Net-works (WSNs). In this paper we employ farcoopt, a cross layer design approach with the concept of coop-eration among the nodes with best farthest neighbor scheme to increase the Quality of Service (QoS), reduce energy consumption, increases performance and end-to-end throughput. We present cooperative transmission to connect previously disconnect parts of a network thus overcoming the separation problem of multi-hop network. We show that this approach improves connectivity over 50% compared to multi-hop approaches and reduces the number of nodes necessary to provide full coverage of an area up to 35%. Simulation results show that on increase of data rates i.e. packet the network life time increases in farcoopt as compared to tra-ditional multi hop approach. The result of this analysis is presented in this work.

A Cross-Layer Optimization Framework for Energy Efficiency in Wireless Sensor Networks

We consider the extension of network lifetime of battery driven wireless sensor networks by splitting the sensing area into uniform clusters and implementing heterogeneous modulation schemes at different members of the clusters. A cross-layer optimization has been proposed to reduce total energy expenditure of the network;at network layer, routing is done through uniform clusters;at MAC layer, each sensor node of the cluster is assigned fixed or variable time slots and at physical layer different member of the clusters is assigned different modulation techniques. MATLAB simulation proved substantial network lifetime gains.

Cross Layered MAC Design for RF Energy Harvesting Sensor Network

The main research objective in wireless sensor networks (WSN) domain is to develop algorithms and protocols to ensure minimal energy consumption with maximum network lifetime. In this paper, we propose a novel design for energy harvesting sensor node and cross-layered MAC protocol using three adjacent layers (Physical, MAC and Network) to economize energy for WSN. The basic idea behind our protocol is to re-energize the neighboring nodes using the radio frequency (RF) energy transmitted by the active nodes. This can be achieved by designing new energy harvesting sensor node and redesigning the MAC protocol. The results show that the proposed cross layer CL_EHSN improves the life time of the WSN by 40%.

Role of Cross Layer Based Intrusion Detection System for Wireless Domain

Wireless mesh networks are very common both for organizations and individuals. Many laptops, computers have wireless cards pre-installed for buyer. However a wireless networking has many security issues. An intrusions detection system aim to detect the different attacks against network and system. An intrusion detection system should be capable for detecting the misuse of the network whether it will be by the authenticated user or by an attacker. They detect attempts and active misuse either by legitimate users of the information systems or by external. The present paper deals with cross layer based intrusion detection system for wireless domain—a critical anlaysis. The present paper deals with role of cross layer based intrusion detection system for wireless domain.

A Contention-Based MAC and Routing Protocol for Wireless Sensor Network

Advance development of wireless technologies and micro-sensor systems have enabled Wireless Sensor Network (WSN) to emerge as a leading solution in many crucial sensor-based applications. WSN deploys numerous resource-constrained sensor nodes which have limited power supply, memory and computation capability in a harsh environment. Inefficient routing strategy results in degraded network performance in terms of reliability, latency and energy efficiency. In this paper, a cross-layer design, Contention-based MAC and Routing protocol is proposed, termed Contention/SNIR-Based Forwarding (CSBF) protocol. CSBF utilizes the geographical information of sensor nodes to effectively guide the routing direction towards destination node, thereby enhancing reliability. Furthermore, Signal-to-Noise-plus-Interference Ratio (SNIR) metric is used as a routing parameter to guarantee high quality link for data transmission. A Contention-Winner Relay scheme is utilized to reduce the delays caused by the contention procedure. Energy efficiency is also improved by introducing sleep mode technique in CSBF. The simulation work is carried out via OMNeT++ network simulator. The performance of CSBF is compared with other existing routing protocols such as AODV and DSDV in terms of packet delivery ratio (PDR), average end-to-end (ETE) delay and energy consumption per packet. Simulation results highlight that CSBF outperforms AODV and DSDV protocols in respect of PDR and energy efficiency. CSBF also has the most consistent overall network performance.

大跨度装配式单层网壳十字形半刚性螺栓连接节点抗弯性能研究

装配式连接节点是大跨度装配式单层空间网壳结构体系的关键。提出一种适用于大跨度单层网壳结构的十字形板装配式节点。该节点由圆钢管、十字形钢板、角钢、矩形连接盖板、圆盖板和高强螺栓组成,其中圆钢管、盖板、十字形钢板在工厂焊接,现场将十字形板和角钢、矩形盖板用高强螺栓连接。该节点通过设置角钢、矩形连接盖板和十字形钢板螺栓连接,在节点受到弯曲荷载时,角钢和矩形连接盖板可以首先承受弯曲荷载,从而减少节点内侧的十字形钢板塑性损伤,并且提高节点的抗弯性能。利用有限元模拟方法,构建新型连接节点有限元模型,分析了十字形钢板和角钢厚度等变量如何影响节点在平面内外的抗弯性能。通过对各组成部分尺寸的参数化研究,得到了这些因素对所提出的连接节点平面内外抗弯性能的影响规律。研究结果表明,采用角钢与矩形盖板相连接形成的十字形节点,在抗弯刚度和承载力方面表现出了优异的性能。通过调节十字形板厚度、螺栓个数、角钢和盖板厚度可调控节点的初始抗弯刚度和抗弯承载力。基于刚性节点设计方法,对该半刚性节点进行尺寸理论设计,结果表明该方法可以保证节点弯矩设计值基本达到圆钢管的屈服弯矩,满足设计要求,提高节点安全。

一种基于V-BLAST技术的多跳协作式传感器网络的跨层设计

协作式(虚拟)MIMO技术被认为是新兴有效的传感器网络节能解决方案之一.本文在考虑网络电路能耗的情况下,采用跨层设计方法提出了一种能量高效的多跳协作式V-BLAST传输策略.为了达到网络寿命最大化的目标,本文建立并分析了系统能耗模型,在此基础上对传输速率、传输跳数、分簇个数和协作式天线节点个数等网络参数进行了联合优化.仿真结果表明,通过选取最优网络参数,本文所提出的策略相比传统的多跳路由协议和LEACH协议能显著降低节点传输能耗和延长网络寿命.

DVB-RCS网络中的跨层协议优化研究

由于DVB-RCS网络长传播延迟以及高误码率的特点,会造成所承载TCP业务的性能下降。传统的分层协议设计方式已经不适合这种动态变化的网络特点。采用跨层协议设计方式优化TCP协议性能。跨层设计方式结合了传输层上TCP协议的工作特点,MAC层的接入策略以及物理层上的自适应调制编码策略。仿真结果显示了跨层协议设计相对于传统协议设计方式性能上的优势。

时延反馈下的自适应STBC-Beamforming跨层设计

为提高无线通信网络的频谱效率,提出一种自适应空时分组编码波束成形(STBC-beamforming)跨层设计方案.该方案利用自适应编码调制技术与混合自动重传技术交互协作,使发射端可以根据反馈延时信息自适应调节调制模式,选择发射权以及自动重传数据.推导了系统在时延反馈条件下的频谱效率和中断概率的闭合表达式,分析了时延反馈对系统性能的影响.仿真结果表明,对比单发/单收跨层系统和Alamouti’s跨层系统,自适应STBC-beamforming跨层系统的性能有明显提高.