BACKGROUND Congenital duodenal webs are rare in adults and can lead to various symptoms such as nausea,vomiting,and postprandial fullness.The treatment for this disease is mostly surgical.Endoscopic treatment techniqu...BACKGROUND Congenital duodenal webs are rare in adults and can lead to various symptoms such as nausea,vomiting,and postprandial fullness.The treatment for this disease is mostly surgical.Endoscopic treatment techniques have been developed and attempted for this disease.Endoscopic radial incision and cutting(RIC)techniques are reportedly very effective in benign anastomotic stricture.This case report highlights the effectiveness and safety of endoscopic RIC as a minimally invasive treatment for adult congenital duodenal webs.CASE SUMMARY A 23-year-old female patient with indigestion was referred to a tertiary hospital.The patient complained of postprandial fullness in the epigastric region.Previous physical examinations or blood tests indicated no abnormalities.Computed tomography revealed an eccentric broad-based delayed-enhancing mass-like lesion in the second portion of the duodenum.Endoscopy showed an enlarged gastric cavity and a significantly dilated duodenal bulb;a very small hole was observed in the distal part of the second portion,and scope passage was not possible.Gastrografin upper gastrointestinal series was performed,revealing an intraduodenal barium contrast-filled sac with a curvilinear narrow radiolucent rim,a typical"windsock"sign.Endoscopic RIC was performed on the duodenal web.The patient recovered uneventfully.Follow-up endoscopy showed a patent duodenal lumen without any residual stenosis.The patient reported complete resolution of symptoms at the 18-month follow-up.CONCLUSION Endoscopic RIC may be an effective treatment for congenital duodenal webs in adults.展开更多
With the third innovation in science and technology worldwide, China has also experienced thismarvelous progress. Concerning the longwall mining in China, the "masonry beam theory" (MBT) wasfirst proposed in the 1...With the third innovation in science and technology worldwide, China has also experienced thismarvelous progress. Concerning the longwall mining in China, the "masonry beam theory" (MBT) wasfirst proposed in the 1960s, illustrating that the transmission and equilibrium method of overburdenpressure using reserved coal pillar in mined-out areas can be realized. This forms the so-called "121mining method", which lays a solid foundation for development of mining science and technology inChina. The "transfer rock beam theory" (TRBT) proposed in the 1980s gives a further understanding forthe transmission path of stope overburden pressure and pressure distribution in high-stress areas. In thisregard, the advanced 121 mining method was proposed with smaller coal pillar for excavation design,making significant contributions to improvement of the coal recovery rate in that era. In the 21st century,the traditional mining technologies faced great challenges and, under the theoretical developmentspioneered by Profs. Minggao Qian and Zhenqi Song, the "cutting cantilever beam theory" (CCBT) wasproposed in 2008. After that the 110 mining method is formulated subsequently, namely one stope face,after the first mining cycle, needs one advanced gateway excavation, while the other one is automaticallyformed during the last mining cycle without coal pillars left in the mining area. This method can beimplemented using the CCBT by incorporating the key technologies, including the directional presplittingroof cutting, constant resistance and large deformation (CRLD) bolt/anchor supporting systemwith negative Poisson's ratio (NPR) effect material, and remote real-time monitoring technology. TheCCBT and 110 mining method will provide the theoretical and technical basis for the development ofmining industry in China.展开更多
High-quality wood products and valuable wood crafts receive everyone’s favor with the rapid development of the economy.In order to improve the cutting surface quality of wood forming parts,the cutting experiment of r...High-quality wood products and valuable wood crafts receive everyone’s favor with the rapid development of the economy.In order to improve the cutting surface quality of wood forming parts,the cutting experiment of renewable Fraxinus mandshurica was conducted by waterjet-assisted CO_(2)laser(WACL)technology.A quadratic mathematical model for describing the relationship between surface roughness changes and cutting parameters was established.The effects of cutting speed,flow pressure and laser power on the kerf surface roughness of Fraxinus mandshurica when cutting transversally were discussed by response surface method.The experimental results showed that kerf surface roughness decreased under a lower laser power,higher cutting speed and higher flow pressure.When the cutting speed was 30 mm/s,flow pressure was 1.58 MPa and laser power was 45 W,the actual surface roughness of the optimized Fraxinus mandshurica was 2.41μm,and it was in accord with the theoretically predicted surface roughness value of 2.54μm,so the model fitted the actual situation well.Through the analysis of 3D profile morphology and micromorphology,it was concluded that the optimized kerf surface of Fraxinus mandshurica was smoother,the cell wall was not destroyed and the tracheid was clear.It provides the theoretical basis for wood micromachining.展开更多
Taguchi method has been employed to investigate the effects of cutting fluids on surface roughness in turning AISI 1330 alloy steel, using manually operated lathe machine. Experiments have been conducted using L<su...Taguchi method has been employed to investigate the effects of cutting fluids on surface roughness in turning AISI 1330 alloy steel, using manually operated lathe machine. Experiments have been conducted using L<sub>27 </sub>(3<sup>4</sup>) orthogonal array and each experiment was repeated three times and each test used a new cutting tool, High Speed Steel (HSS), to ensure accurate readings of the surface roughness. The statistical methods of Signal-to-Noise (S/N) ratio and the Analysis of Variance (ANOVA) were applied to investigate effects of cutting speed, feed rate and depth of cut on surface roughness under different cutting fluids. Minitab 14 software was used to analyze the effect of variables on the surface roughness. Results obtained indicated that optimal variables for the minimum surface roughness were cutting speed of 35 m/min (level 2), feed of 0.124 mm/rev (level 1), depth of cut of 0.3 mm (level 1) and a cutting fluid with a viscosity of 2.898 mm<sup>2</sup>/s (level 3). Hence, the optimal parameters to obtain better surface roughness of the workpiece material were obtained when groundnut oil based cutting fluid was used. Analysis of variance shows that feed rate has the most significant effect on surface roughness.展开更多
Bamboo is one of the fastest growing and highest yielding renewable resources with multiple uses in the world. Lack of seedlings in sufficient number has generally been a major constraint in establishing more bamboo p...Bamboo is one of the fastest growing and highest yielding renewable resources with multiple uses in the world. Lack of seedlings in sufficient number has generally been a major constraint in establishing more bamboo plantations. This study investigated the efficiency of regenerating Bambusa vulgaris through cuttings at Busogo sector, Musanze district, using vertical and horizontal methods with and without water treatment. The experiment consisted in a RCBD (Randomized Complete Block Design) with 4 replications. The growth and sprouting of the 64 cuttings were monitored for three months and 18 days (105 days). In terms of planting method, horizontal planting method showed best sprouting percentage of 68%. In terms of treatment used, horizontal planting method without using water treatment showed slightly better sprouting percentage of 60%. The results further show that about 87% of sprouts had between 0 and 30 cm height and 98% of sprouts had basal diameter ranging from 0 to 20 mm only 105 days after planting. Indeed, the horizontal planting methods provided highest survival rate of sprouts than the vertical planting method (74%) of planted cuttings. Furthermore, the results show that, 105 days after planting, cuttings with horizontal method were more productive in terms of root development. In terms of planting method using water treatment, the horizontal planting method with water treatment showed highest rooting percentage (44%). Therefore, farmers should be trained and encouraged to use horizontal planting method using water treatment in order to get better results in regenerating bamboo through cuttings.展开更多
This paper mainly describes a new approach to optimizing of the cutting glass fiber with multiple performance characteristics, based on reliability analysis, Taguchi and Grey methods. During the cutting process, the s...This paper mainly describes a new approach to optimizing of the cutting glass fiber with multiple performance characteristics, based on reliability analysis, Taguchi and Grey methods. During the cutting process, the speed, the volume and the cutting load are optimized cutting parameters when the performance characteristics, which include Weibull modulus and blade wear, are taken into consideration. In this paper, optimization with multiple performance characteristics is found to be the highest cutting speed and the smallest cutting volume, and the medium cutting load. An analysis of the variance of the blade wear indicates that the cutting speed (47.21%), the cutting volume (14.62%) and the cutting load (12.20%) are the most significant parameters in the cutting process of glass fibers. In summary, the most optimal cutting parameter should be A3B1C2. The results of experiments have shown that the multiple performance characteristics of cutting glass fiber are improved effectively through this approach.展开更多
This paper presents an experimental investigation focused on identifying the effects of cutting conditions and tool construction on the surface roughness and natural frequency in turning of AISI1045 steel. Machining e...This paper presents an experimental investigation focused on identifying the effects of cutting conditions and tool construction on the surface roughness and natural frequency in turning of AISI1045 steel. Machining experiments were carried out at the lathe using carbide cutting insert coated with TiC and two forms of cutting tools made of AISI 5140 steel. Three levels for spindle speed, depth of cut, feed rate and tool overhang were chosen as cutting variables. The Taguchi method L9 orthogonal array was applied to design of experiment. By the help of signal-to-noise ratio and analysis of variance, it was concluded that spindle speed has the significant effect on the surface roughness, while tool overhang is the dominant factor affecting natural frequency for both cutting tools. In addition, the optimum cutting conditions for surface roughness and natural frequency were found at different levels. Finally, confirmation experiments were conducted to verify the effectiveness and efficiency of the Taguchi method in optimizing the cutting parameters for surface roughness and natural frequency.展开更多
Hysterectomy for large uterine cervical myoma is a challenging surgical procedure due to the limited operative field for lateral and posterior dissections. Existing procedures such as performing myomectomy before hyst...Hysterectomy for large uterine cervical myoma is a challenging surgical procedure due to the limited operative field for lateral and posterior dissections. Existing procedures such as performing myomectomy before hysterectomy or performing retrograde hysterectomy remain suboptimal in expanding the operative field, especially in cases with a huge cervical myoma. In this report, we introduce a new procedure, the “HALF-CUTTING METHOD” which can be used to obtain an adequate surgical field during hysterectomy.展开更多
The petroleum industry has shown great interest in the study of drilling optimization on pre-salt formations given the low rates of penetration observed so far. Rate of penetration is the key to economically drill the...The petroleum industry has shown great interest in the study of drilling optimization on pre-salt formations given the low rates of penetration observed so far. Rate of penetration is the key to economically drill the pre-salt carbonate rock. This work presents the results of numerical modeling through finite element method and discrete element method for single cutter drilling in carbonate samples. The work is relevant to understand the mechanics of drill bit-rock interaction while drilling deep wells and the results were validated with experimental data raised under simulated downhole conditions. The numerical models were carried out under different geometrical configurations, varying the cutter chamfer size and back-rake angles. The forces generated on the cutter are translated into mechanical specific energy as this parameter is often used to measure drilling efficiency. Results indicate that the chamfer size does not change significantly the mechanical specific energy values, characteristic. Results also show there is a significant increase although the cutter aggressiveness is influenced by this geometrical in drilling resistance for larger values of back-rake angle.展开更多
The generation expansion planning is one of complex mixed-integer optimization problems, which involves a large number of continuous or discrete decision variables and constraints. In this paper, an interior point wit...The generation expansion planning is one of complex mixed-integer optimization problems, which involves a large number of continuous or discrete decision variables and constraints. In this paper, an interior point with cutting plane (IP/CP) method is proposed to solve the mixed-integer optimization problem of the electrical power generation expansion planning. The IP/CP method could improve the overall efficiency of the solution and reduce the computational time. Proposed method is combined with the Bender's decomposition technique in order to decompose the generation expansion problem into a master investment problem and a slave operational problem. The numerical example is presented to compare with the effectiveness of the proposed algorithm.展开更多
The rapid discharge of cuttings from the air cushion chamber is crucial for the construction safety and excavation efficiency of the slurry shield.Previous studies have mainly focused on the transport characteristics ...The rapid discharge of cuttings from the air cushion chamber is crucial for the construction safety and excavation efficiency of the slurry shield.Previous studies have mainly focused on the transport characteristics of cuttings in the slurry discharge pipe,while the complete process of cuttings entering the slurry discharge pipe from the air cushion chamber until they are discharged was often overlooked.Based on the CFD-DEM coupling method and combined with actual engineering,this paper established a numerical model that can more completely reflect the cuttings discharge process during slurry shield tunneling,and the effects of the slurry velocity at slurry gate and scouring pipes,inclination angle of slurry discharge pipe,cuttings diameter and shape coefficient were investigated by analyzing the variation in the mass flow rate,mass of discharged cuttings,and discharged ratio.The results revealed that increasing the slurry velocity can promote the discharge of cuttings.To keep the discharged rate at a high level,it is recommended that the slurry velocity at the slurry gate should be greater than 0.15 m/s.Reducing the inclination angle of the discharge pipe is conducive to the rapid discharge of cuttings.Cuttings with large diameter or small shape coefficient are more prone to accumulate in the air cushion chamber and cause clogging risk.The research results not only help to improve engineers'understanding of cuttings discharge in slurry shield,but also provide practical guidance for formulating relevant construction measures.展开更多
Mechanical cutting provides one of the most flexible and environmentally friendly excavation methods.It has attracted numerous efforts to model the rock chipping and fragmentation process,especially using the explicit...Mechanical cutting provides one of the most flexible and environmentally friendly excavation methods.It has attracted numerous efforts to model the rock chipping and fragmentation process,especially using the explicit finite element method(FEM) and bonded particle model(BPM),in order to improve cutting efficiency.This study investigates the application of a general-purpose graphic-processing-unit parallelised hybrid finite-discrete element method(FDEM) which enjoys the advantages of both explicit FEM and BPM,in modelling the rock chipping and fragmentation process in the rock scratch test of mechanical rock cutting.The input parameters of FDEM are determined through a calibration procedure of modelling conventional Brazilian tensile and uniaxial compressive tests of limestone,A series of scratch tests with various cutting velocities,cutter rake angles and cutting depths is then modelled using FDEM with calibrated input parameters.A few cycles of cutter/rock interactions,including their engagement and detachment process,are modelled for each case,which is conducted for the first time to the best knowledge of the authors,thanks to the general purpose graphic processing units(GPGPU) parallelisation.The failure mechanism,cutting force,chipping morphology and effect of various factors on them are discussed on the basis of the modelled results.Finally,it is concluded that GPGPU-parallelised FDEM provides a powerful tool to further study rock cutting and improve cutting efficiencies since it can explicitly capture different fracture mechanisms contributing to the rock chipping as well as chip formation and the separation process in mechanical cutting.Moreover,it is concluded that chipping is mostly owed to the mix-mode Ⅰ-Ⅱ fracture in all cases although mode Ⅱ cracks and mode Ⅰ cracks are the dominant failures in rock cutting with shallow and deep cutting depths,respectively.The chip morphology is found to be a function of cutter velocdty,cutting depth and cutter rake angle.展开更多
Since the 1960 s, mining science and technology in China has experienced two technical innovations, i.e.the ‘‘Masonry Beam Theory(MBT)" and ‘‘Transfer Rock Beam Theory(TRBT)". Based on those theories, th...Since the 1960 s, mining science and technology in China has experienced two technical innovations, i.e.the ‘‘Masonry Beam Theory(MBT)" and ‘‘Transfer Rock Beam Theory(TRBT)". Based on those theories, the conventional mining method(being called the 121 mining method) was established, consisting of excavating two tunnels with a pillar left for mining a working panel. However, with increasing mining depth,engineering geological disasters in the underground caverns have been frequently encountered. In addition, the use of the coal-pillar mining results in a large amount of coal resources unexploited. In order to address the problems above, the ‘‘Roof Cut Short-Arm Beam Theory(RCSBT), being called the 110 mining method)" was proposed by He Manchao in 2008. The 110 mining method features the mining of one coal seam panel, excavating necessarily only one roadway tunnel and leaving no pillars. Realization of the 110 mining method includes the following steps:(1) directional pre-splitting roof cutting,(2) supporting the roof by using high Constant Resistance Large Deformation bolt/cable(CRLD), and(3) blocking gangue by hydraulic props. This paper presents an overview of the principles, techniques and application of the 110 mining method. Special emphasis is placed on the numerical simulation of the geostress distribution found in the mining panel using the 110 method compared to that of the 121 method. In addition, the stress distribution on the ‘‘short beam" left by the roof cutting when performing the 110 method was also investigated using both numerical simulation and theoretical formulation.展开更多
Pre-driven longwall retracement roadway(PLRR)is commonly used in large mine shaft.The support crushing disasters occur frequently during the retracement,and roof management is necessary.Taking the 31107 panel as resea...Pre-driven longwall retracement roadway(PLRR)is commonly used in large mine shaft.The support crushing disasters occur frequently during the retracement,and roof management is necessary.Taking the 31107 panel as research background,the roof breaking structure of PLRR is analyzed.It is concluded that the roof cutting with vertical hydraulic fracture(HF)at a specified position,that is,fixed-length roof cutting,can reduce support load and keep immediate roof intact.The extended finite element method(XFEM)is applied to simulate hydraulic fracturing.The results show that both the axial and transverse hydraulic fracturing cannot effectively create vertical HFs.Therefore,a novel construction method of vertical HF based on the stress shadow effect(SSE)is proposed.The stress reversal region and HF orientation caused by the prefabricated hydraulic fracture(PF)are verified in simulation.The sub-vertical HFs are obtained between two PFs,the vertical extension range of which is much larger than that of directional hydraulic fracturing.The new construction method was used to determine the field plan for fixed-length roof cutting.The roof formed a stable suspended structure and deformation of the main PLRR was improved after hydraulic fracturing.展开更多
Segmentation of three-dimensional(3D) complicated structures is of great importance for many real applications.In this work we combine graph cut minimization method with a variant of the level set idea for 3D segmenta...Segmentation of three-dimensional(3D) complicated structures is of great importance for many real applications.In this work we combine graph cut minimization method with a variant of the level set idea for 3D segmentation based on the Mumford-Shah model.Compared with the traditional approach for solving the Euler-Lagrange equation we do not need to solve any partial differential equations.Instead,the minimum cut on a special designed graph need to be computed.The method is tested on data with complicated structures.It is rather stable with respect to initial value and the algorithm is nearly parameter free.Experiments show that it can solve large problems much faster than traditional approaches.展开更多
To optimize cutting control parameters and provide scientific evidence for controlling cutting forces,cutting force modeling and cutting control parameter optimization are researched with one tool adopted to orbital d...To optimize cutting control parameters and provide scientific evidence for controlling cutting forces,cutting force modeling and cutting control parameter optimization are researched with one tool adopted to orbital drill holes in aluminum alloy 6061.Firstly,four cutting control parameters(tool rotation speed,tool revolution speed,axial feeding pitch and tool revolution radius)and affecting cutting forces are identified after orbital drilling kinematics analysis.Secondly,hybrid level orthogonal experiment method is utilized in modeling experiment.By nonlinear regression analysis,two quadratic prediction models for axial and radial forces are established,where the above four control parameters are used as input variables.Then,model accuracy and cutting control parameters are analyzed.Upon axial and radial forces models,two optimal combinations of cutting control parameters are obtained for processing a13mm hole,corresponding to the minimum axial force and the radial force respectively.Finally,each optimal combination is applied in verification experiment.The verification experiment results of cutting force are in good agreement with prediction model,which confirms accracy of the research method in practical production.展开更多
Ciprofloxacin is a second-generation of fluoroquinolone,broad-spectrum antibiotic with bactericidal activity against Gram-positive and Gram-negative organisms.It is one of the most widely used antibiotics,because of i...Ciprofloxacin is a second-generation of fluoroquinolone,broad-spectrum antibiotic with bactericidal activity against Gram-positive and Gram-negative organisms.It is one of the most widely used antibiotics,because of its efficacy,safety,and relatively low cost.Ascorbic acid(vitamin C)is water-soluble monosaccharide antioxidant;it is essentially required by the body for its various biochemical and physiological processes.S.aureus is Gram-positive cocci;widely distributed in the environment,it is a member of the normal flora of the body.S.aureus is not always pathogenic;it is a common cause of skin infections including abscesses,respiratory infections such as sinusitis,and food poisoning.E.coli is Gram-negative bacteria,found in the environment,foods,and intestines.Most E.coli strains are harmless;it is part of the normal microbiota of the gut.However,some serotypes of E.coli cause serious food poisoning in their hosts;it can cause diarrhea,while others cause urinary tract infections,respiratory illness and pneumonia,and other illnesses.Method:Cup cut diffusion method was applied.Experiment I:is carried out to choose the concentration of vitamin C to be used in experiment II.The negative control is normal saline,added in cup in each plate,vitamin C(100 mg/mL,200 mg/mL,400 mg/mL)was added,the volume in each cup was 100μL.Experiment II:Eight groups of treatments were applied.The first is the negative control(1%normal saline),the second group is the positive control of vitamin C(200 mg/mL).The third,fourth and fifth groups are ciprofloxacin with different concentrations(10 mg/mL,20 mg/mL,40 mg/mL);the sixth,seventh and eighth are the combination of vitamin C with each concentration of ciprofloxacin(10 mg/mL,20 mg/mL,40 mg/mL).Each group includes six petri dishes.Bacterial plates were incubated at 37 oC for 24 h and 48 h.Zone of inhibition is measured in mm.Results and conclusion:Ciprofloxacin produces dose dependent increase in zone of inhibition of S.aureus and E.coli growth,after 24 and 48 hours incubation.While vitamin C in the concentration used produced inhibitory effect on the growth of S.aureus and E.coli,after 24 hours incubation,vitamin C effect was not changed after 48 hours incubation.After 24 hours incubation,vitamin C potentiated the effect of ciprofloxacin at low concentration(10 mg/mL);while vitamin C antagonized the effect of ciprofloxacin at higher concentrations(20 and 40 mg/mL)on S.aureus growth.In the same time,ciprofloxacin antagonized the inhibitory effect of vitamin C on S.aureus growth.After 48 hours incubation,S.aureus produced resistance against ciprofloxacin alone,and that combined with vitamin C compared to zone of inhibition after 24 hours.Ciprofloxacin produced dose dependent inhibition of E.coli growth after incubation for 24 and 48 hours.Vitamin C potentiated the inhibitory effect induced by ciprofloxacin(additive effect).The inhibitory effect of ciprofloxacin,vitamin C and the combination was not changed after 48 hours compared to 24 hours.展开更多
A M_L3.8 earthquake occurred on February 23,2014 in Rongchang County,which is located at the southern edge of the Sichuan Basin in the border area between Sichuan and Chongqing. This paper presents results of focal me...A M_L3.8 earthquake occurred on February 23,2014 in Rongchang County,which is located at the southern edge of the Sichuan Basin in the border area between Sichuan and Chongqing. This paper presents results of focal mechanism solution of this earthquake using the CAP( cut and paste) method based on broadband seismograms recorded by regional seismic stations. Our results show that the moment magnitude is M_W3. 09 and focal depth is 3km. The hypocenter of this earthquake is located close to a buried fault in the Luoguangshan anticline. Oil prospecting and deep drilling data indicate that this buried fault is a thrust fault,striking SW230°,dipping NW45°,and 1. 7km deep. There are some injection wells within the anticline,and significant injection-induced earthquakes were observed during the periods of injection of waste water into the deep formations through those wells. The best double couple solution of the M_L3.8 earthquake is 247°,48°and 104° for strike,dip and rate,respectively,for one nodal plane( and 46°,44° and 74°for another nodal plane),which is in agreement with the geometry of the buried fault.Therefore,we conclude that the M_L3.8 Rongchang earthquake is possibly the result of faulting along the buried reverse fault induced by water injection under the compressive stress regime in the area.展开更多
The kineto-elastodynamic(KED) model of a hose cutting mechanism used in the aluminum electrolytic capacitor(AEC) casing machine is developed to investigate the dynamic characteristics. According to the composition cha...The kineto-elastodynamic(KED) model of a hose cutting mechanism used in the aluminum electrolytic capacitor(AEC) casing machine is developed to investigate the dynamic characteristics. According to the composition characteristics, the cutting mechanism is divided into cam-roller and linkage two substructures. And the dynamic models of the two substructures are established using the lumped parameter method and finite element method(FEM), respectively. In the model, the compliances of the camshaft and the links are taken into consideration. The elastic displacement of the links, angular error of the cutter and the dynamic stress of the links are analyzed based on the KED model. The results provide important information for structure optimization and vibration control of the mechanism.展开更多
The dynamic performances of an ultra-precision fly cutting machine tool(UFCMT)has a dramatic impact on the quality of ultra-precision machining.In this study,the dynamic model of an UFCMT was established based on the ...The dynamic performances of an ultra-precision fly cutting machine tool(UFCMT)has a dramatic impact on the quality of ultra-precision machining.In this study,the dynamic model of an UFCMT was established based on the transfer matrix method for multibody systems.In particular,the large-span scale flow field mesh model was created;and the variation in linear and angular stiffness of journal and thrust bearings with respect to film thickness was investigated by adopting the dynamic mesh technique.The dynamic model was proven to be valid by comparing the dynamic characteristics of the machine tool obtained by numerical simulation with the experimental results.In addition,the power spectrum density estimation method was adopted to simulate the statistical ambient vibration excitation by processing the ambient vibration signal measured over a long period of time.Applying it to the dynamic model,the dynamic response of the tool tip under ambient vibration was investigated.The results elucidated that the tool tip response was significantly affected by ambient vibration,and the isolation foundation had a good effect on vibration isolation.展开更多
文摘BACKGROUND Congenital duodenal webs are rare in adults and can lead to various symptoms such as nausea,vomiting,and postprandial fullness.The treatment for this disease is mostly surgical.Endoscopic treatment techniques have been developed and attempted for this disease.Endoscopic radial incision and cutting(RIC)techniques are reportedly very effective in benign anastomotic stricture.This case report highlights the effectiveness and safety of endoscopic RIC as a minimally invasive treatment for adult congenital duodenal webs.CASE SUMMARY A 23-year-old female patient with indigestion was referred to a tertiary hospital.The patient complained of postprandial fullness in the epigastric region.Previous physical examinations or blood tests indicated no abnormalities.Computed tomography revealed an eccentric broad-based delayed-enhancing mass-like lesion in the second portion of the duodenum.Endoscopy showed an enlarged gastric cavity and a significantly dilated duodenal bulb;a very small hole was observed in the distal part of the second portion,and scope passage was not possible.Gastrografin upper gastrointestinal series was performed,revealing an intraduodenal barium contrast-filled sac with a curvilinear narrow radiolucent rim,a typical"windsock"sign.Endoscopic RIC was performed on the duodenal web.The patient recovered uneventfully.Follow-up endoscopy showed a patent duodenal lumen without any residual stenosis.The patient reported complete resolution of symptoms at the 18-month follow-up.CONCLUSION Endoscopic RIC may be an effective treatment for congenital duodenal webs in adults.
基金supported by the National Natural Science Foundation of China (No. 51404278)the State Key Program of National Natural Science Foundation of China (No. 51134005)
文摘With the third innovation in science and technology worldwide, China has also experienced thismarvelous progress. Concerning the longwall mining in China, the "masonry beam theory" (MBT) wasfirst proposed in the 1960s, illustrating that the transmission and equilibrium method of overburdenpressure using reserved coal pillar in mined-out areas can be realized. This forms the so-called "121mining method", which lays a solid foundation for development of mining science and technology inChina. The "transfer rock beam theory" (TRBT) proposed in the 1980s gives a further understanding forthe transmission path of stope overburden pressure and pressure distribution in high-stress areas. In thisregard, the advanced 121 mining method was proposed with smaller coal pillar for excavation design,making significant contributions to improvement of the coal recovery rate in that era. In the 21st century,the traditional mining technologies faced great challenges and, under the theoretical developmentspioneered by Profs. Minggao Qian and Zhenqi Song, the "cutting cantilever beam theory" (CCBT) wasproposed in 2008. After that the 110 mining method is formulated subsequently, namely one stope face,after the first mining cycle, needs one advanced gateway excavation, while the other one is automaticallyformed during the last mining cycle without coal pillars left in the mining area. This method can beimplemented using the CCBT by incorporating the key technologies, including the directional presplittingroof cutting, constant resistance and large deformation (CRLD) bolt/anchor supporting systemwith negative Poisson's ratio (NPR) effect material, and remote real-time monitoring technology. TheCCBT and 110 mining method will provide the theoretical and technical basis for the development ofmining industry in China.
基金supported by the Joint Scientific and Technological Innovation Project of Hainan Province(2021CXLH0001)the Teaching Reform in Higher Education of Heilongjiang Province(SJGY20210135)+4 种基金the Key Subject of Education Planning in Heilongjiang Province(GJB1423352)the Guiding Innovation Fund Project of Northeast Petroleum University(2022YDL-06 and 2021YDL-13)Daqing City Guiding Science and Technology Project(zd-2021-41)the Scientific Research Start-Up Fund Project of Northeast Petroleum University(2021KQ09 and 2019KQ67)the National Key R&D Program of China(2017YFD0601004).
文摘High-quality wood products and valuable wood crafts receive everyone’s favor with the rapid development of the economy.In order to improve the cutting surface quality of wood forming parts,the cutting experiment of renewable Fraxinus mandshurica was conducted by waterjet-assisted CO_(2)laser(WACL)technology.A quadratic mathematical model for describing the relationship between surface roughness changes and cutting parameters was established.The effects of cutting speed,flow pressure and laser power on the kerf surface roughness of Fraxinus mandshurica when cutting transversally were discussed by response surface method.The experimental results showed that kerf surface roughness decreased under a lower laser power,higher cutting speed and higher flow pressure.When the cutting speed was 30 mm/s,flow pressure was 1.58 MPa and laser power was 45 W,the actual surface roughness of the optimized Fraxinus mandshurica was 2.41μm,and it was in accord with the theoretically predicted surface roughness value of 2.54μm,so the model fitted the actual situation well.Through the analysis of 3D profile morphology and micromorphology,it was concluded that the optimized kerf surface of Fraxinus mandshurica was smoother,the cell wall was not destroyed and the tracheid was clear.It provides the theoretical basis for wood micromachining.
文摘Taguchi method has been employed to investigate the effects of cutting fluids on surface roughness in turning AISI 1330 alloy steel, using manually operated lathe machine. Experiments have been conducted using L<sub>27 </sub>(3<sup>4</sup>) orthogonal array and each experiment was repeated three times and each test used a new cutting tool, High Speed Steel (HSS), to ensure accurate readings of the surface roughness. The statistical methods of Signal-to-Noise (S/N) ratio and the Analysis of Variance (ANOVA) were applied to investigate effects of cutting speed, feed rate and depth of cut on surface roughness under different cutting fluids. Minitab 14 software was used to analyze the effect of variables on the surface roughness. Results obtained indicated that optimal variables for the minimum surface roughness were cutting speed of 35 m/min (level 2), feed of 0.124 mm/rev (level 1), depth of cut of 0.3 mm (level 1) and a cutting fluid with a viscosity of 2.898 mm<sup>2</sup>/s (level 3). Hence, the optimal parameters to obtain better surface roughness of the workpiece material were obtained when groundnut oil based cutting fluid was used. Analysis of variance shows that feed rate has the most significant effect on surface roughness.
文摘Bamboo is one of the fastest growing and highest yielding renewable resources with multiple uses in the world. Lack of seedlings in sufficient number has generally been a major constraint in establishing more bamboo plantations. This study investigated the efficiency of regenerating Bambusa vulgaris through cuttings at Busogo sector, Musanze district, using vertical and horizontal methods with and without water treatment. The experiment consisted in a RCBD (Randomized Complete Block Design) with 4 replications. The growth and sprouting of the 64 cuttings were monitored for three months and 18 days (105 days). In terms of planting method, horizontal planting method showed best sprouting percentage of 68%. In terms of treatment used, horizontal planting method without using water treatment showed slightly better sprouting percentage of 60%. The results further show that about 87% of sprouts had between 0 and 30 cm height and 98% of sprouts had basal diameter ranging from 0 to 20 mm only 105 days after planting. Indeed, the horizontal planting methods provided highest survival rate of sprouts than the vertical planting method (74%) of planted cuttings. Furthermore, the results show that, 105 days after planting, cuttings with horizontal method were more productive in terms of root development. In terms of planting method using water treatment, the horizontal planting method with water treatment showed highest rooting percentage (44%). Therefore, farmers should be trained and encouraged to use horizontal planting method using water treatment in order to get better results in regenerating bamboo through cuttings.
文摘This paper mainly describes a new approach to optimizing of the cutting glass fiber with multiple performance characteristics, based on reliability analysis, Taguchi and Grey methods. During the cutting process, the speed, the volume and the cutting load are optimized cutting parameters when the performance characteristics, which include Weibull modulus and blade wear, are taken into consideration. In this paper, optimization with multiple performance characteristics is found to be the highest cutting speed and the smallest cutting volume, and the medium cutting load. An analysis of the variance of the blade wear indicates that the cutting speed (47.21%), the cutting volume (14.62%) and the cutting load (12.20%) are the most significant parameters in the cutting process of glass fibers. In summary, the most optimal cutting parameter should be A3B1C2. The results of experiments have shown that the multiple performance characteristics of cutting glass fiber are improved effectively through this approach.
文摘This paper presents an experimental investigation focused on identifying the effects of cutting conditions and tool construction on the surface roughness and natural frequency in turning of AISI1045 steel. Machining experiments were carried out at the lathe using carbide cutting insert coated with TiC and two forms of cutting tools made of AISI 5140 steel. Three levels for spindle speed, depth of cut, feed rate and tool overhang were chosen as cutting variables. The Taguchi method L9 orthogonal array was applied to design of experiment. By the help of signal-to-noise ratio and analysis of variance, it was concluded that spindle speed has the significant effect on the surface roughness, while tool overhang is the dominant factor affecting natural frequency for both cutting tools. In addition, the optimum cutting conditions for surface roughness and natural frequency were found at different levels. Finally, confirmation experiments were conducted to verify the effectiveness and efficiency of the Taguchi method in optimizing the cutting parameters for surface roughness and natural frequency.
文摘Hysterectomy for large uterine cervical myoma is a challenging surgical procedure due to the limited operative field for lateral and posterior dissections. Existing procedures such as performing myomectomy before hysterectomy or performing retrograde hysterectomy remain suboptimal in expanding the operative field, especially in cases with a huge cervical myoma. In this report, we introduce a new procedure, the “HALF-CUTTING METHOD” which can be used to obtain an adequate surgical field during hysterectomy.
文摘The petroleum industry has shown great interest in the study of drilling optimization on pre-salt formations given the low rates of penetration observed so far. Rate of penetration is the key to economically drill the pre-salt carbonate rock. This work presents the results of numerical modeling through finite element method and discrete element method for single cutter drilling in carbonate samples. The work is relevant to understand the mechanics of drill bit-rock interaction while drilling deep wells and the results were validated with experimental data raised under simulated downhole conditions. The numerical models were carried out under different geometrical configurations, varying the cutter chamfer size and back-rake angles. The forces generated on the cutter are translated into mechanical specific energy as this parameter is often used to measure drilling efficiency. Results indicate that the chamfer size does not change significantly the mechanical specific energy values, characteristic. Results also show there is a significant increase although the cutter aggressiveness is influenced by this geometrical in drilling resistance for larger values of back-rake angle.
文摘The generation expansion planning is one of complex mixed-integer optimization problems, which involves a large number of continuous or discrete decision variables and constraints. In this paper, an interior point with cutting plane (IP/CP) method is proposed to solve the mixed-integer optimization problem of the electrical power generation expansion planning. The IP/CP method could improve the overall efficiency of the solution and reduce the computational time. Proposed method is combined with the Bender's decomposition technique in order to decompose the generation expansion problem into a master investment problem and a slave operational problem. The numerical example is presented to compare with the effectiveness of the proposed algorithm.
基金support from the National Natural Science Foundation of China(grant number 52278403)the Natural Science Foundation of Shandong Province(grant number ZR2021ME135).
文摘The rapid discharge of cuttings from the air cushion chamber is crucial for the construction safety and excavation efficiency of the slurry shield.Previous studies have mainly focused on the transport characteristics of cuttings in the slurry discharge pipe,while the complete process of cuttings entering the slurry discharge pipe from the air cushion chamber until they are discharged was often overlooked.Based on the CFD-DEM coupling method and combined with actual engineering,this paper established a numerical model that can more completely reflect the cuttings discharge process during slurry shield tunneling,and the effects of the slurry velocity at slurry gate and scouring pipes,inclination angle of slurry discharge pipe,cuttings diameter and shape coefficient were investigated by analyzing the variation in the mass flow rate,mass of discharged cuttings,and discharged ratio.The results revealed that increasing the slurry velocity can promote the discharge of cuttings.To keep the discharged rate at a high level,it is recommended that the slurry velocity at the slurry gate should be greater than 0.15 m/s.Reducing the inclination angle of the discharge pipe is conducive to the rapid discharge of cuttings.Cuttings with large diameter or small shape coefficient are more prone to accumulate in the air cushion chamber and cause clogging risk.The research results not only help to improve engineers'understanding of cuttings discharge in slurry shield,but also provide practical guidance for formulating relevant construction measures.
基金the support of CSIRO and the Australia-Japan Foundation(Grant No.17/20470)supported by the Japan Society for the Promotion of Science KAKENHI(Grant No.JP18K14165)for Grant-in-Aid for Young Scientists。
文摘Mechanical cutting provides one of the most flexible and environmentally friendly excavation methods.It has attracted numerous efforts to model the rock chipping and fragmentation process,especially using the explicit finite element method(FEM) and bonded particle model(BPM),in order to improve cutting efficiency.This study investigates the application of a general-purpose graphic-processing-unit parallelised hybrid finite-discrete element method(FDEM) which enjoys the advantages of both explicit FEM and BPM,in modelling the rock chipping and fragmentation process in the rock scratch test of mechanical rock cutting.The input parameters of FDEM are determined through a calibration procedure of modelling conventional Brazilian tensile and uniaxial compressive tests of limestone,A series of scratch tests with various cutting velocities,cutter rake angles and cutting depths is then modelled using FDEM with calibrated input parameters.A few cycles of cutter/rock interactions,including their engagement and detachment process,are modelled for each case,which is conducted for the first time to the best knowledge of the authors,thanks to the general purpose graphic processing units(GPGPU) parallelisation.The failure mechanism,cutting force,chipping morphology and effect of various factors on them are discussed on the basis of the modelled results.Finally,it is concluded that GPGPU-parallelised FDEM provides a powerful tool to further study rock cutting and improve cutting efficiencies since it can explicitly capture different fracture mechanisms contributing to the rock chipping as well as chip formation and the separation process in mechanical cutting.Moreover,it is concluded that chipping is mostly owed to the mix-mode Ⅰ-Ⅱ fracture in all cases although mode Ⅱ cracks and mode Ⅰ cracks are the dominant failures in rock cutting with shallow and deep cutting depths,respectively.The chip morphology is found to be a function of cutter velocdty,cutting depth and cutter rake angle.
文摘Since the 1960 s, mining science and technology in China has experienced two technical innovations, i.e.the ‘‘Masonry Beam Theory(MBT)" and ‘‘Transfer Rock Beam Theory(TRBT)". Based on those theories, the conventional mining method(being called the 121 mining method) was established, consisting of excavating two tunnels with a pillar left for mining a working panel. However, with increasing mining depth,engineering geological disasters in the underground caverns have been frequently encountered. In addition, the use of the coal-pillar mining results in a large amount of coal resources unexploited. In order to address the problems above, the ‘‘Roof Cut Short-Arm Beam Theory(RCSBT), being called the 110 mining method)" was proposed by He Manchao in 2008. The 110 mining method features the mining of one coal seam panel, excavating necessarily only one roadway tunnel and leaving no pillars. Realization of the 110 mining method includes the following steps:(1) directional pre-splitting roof cutting,(2) supporting the roof by using high Constant Resistance Large Deformation bolt/cable(CRLD), and(3) blocking gangue by hydraulic props. This paper presents an overview of the principles, techniques and application of the 110 mining method. Special emphasis is placed on the numerical simulation of the geostress distribution found in the mining panel using the 110 method compared to that of the 121 method. In addition, the stress distribution on the ‘‘short beam" left by the roof cutting when performing the 110 method was also investigated using both numerical simulation and theoretical formulation.
基金financially supported by the Postgraduate Research&Practice Innovation Program of Jiangsu Province(KYCX21_2358)the National Key Research and Development Program of China(2020YFB1314204)National Natural Science Foundation of China(No.52074239)。
文摘Pre-driven longwall retracement roadway(PLRR)is commonly used in large mine shaft.The support crushing disasters occur frequently during the retracement,and roof management is necessary.Taking the 31107 panel as research background,the roof breaking structure of PLRR is analyzed.It is concluded that the roof cutting with vertical hydraulic fracture(HF)at a specified position,that is,fixed-length roof cutting,can reduce support load and keep immediate roof intact.The extended finite element method(XFEM)is applied to simulate hydraulic fracturing.The results show that both the axial and transverse hydraulic fracturing cannot effectively create vertical HFs.Therefore,a novel construction method of vertical HF based on the stress shadow effect(SSE)is proposed.The stress reversal region and HF orientation caused by the prefabricated hydraulic fracture(PF)are verified in simulation.The sub-vertical HFs are obtained between two PFs,the vertical extension range of which is much larger than that of directional hydraulic fracturing.The new construction method was used to determine the field plan for fixed-length roof cutting.The roof formed a stable suspended structure and deformation of the main PLRR was improved after hydraulic fracturing.
基金support from the Centre for Integrated Petroleum Research(CIPR),University of Bergen, Norway,and Singapore MOE Grant T207B2202NRF2007IDMIDM002-010
文摘Segmentation of three-dimensional(3D) complicated structures is of great importance for many real applications.In this work we combine graph cut minimization method with a variant of the level set idea for 3D segmentation based on the Mumford-Shah model.Compared with the traditional approach for solving the Euler-Lagrange equation we do not need to solve any partial differential equations.Instead,the minimum cut on a special designed graph need to be computed.The method is tested on data with complicated structures.It is rather stable with respect to initial value and the algorithm is nearly parameter free.Experiments show that it can solve large problems much faster than traditional approaches.
基金Supported by the National Natural Science Foundation of China(50975141)the Aviation Science Fund(20091652018,2010352005)the National Science and Technology Major Project of the Ministry of Science and Technology of China(2012ZX04003031-4)
文摘To optimize cutting control parameters and provide scientific evidence for controlling cutting forces,cutting force modeling and cutting control parameter optimization are researched with one tool adopted to orbital drill holes in aluminum alloy 6061.Firstly,four cutting control parameters(tool rotation speed,tool revolution speed,axial feeding pitch and tool revolution radius)and affecting cutting forces are identified after orbital drilling kinematics analysis.Secondly,hybrid level orthogonal experiment method is utilized in modeling experiment.By nonlinear regression analysis,two quadratic prediction models for axial and radial forces are established,where the above four control parameters are used as input variables.Then,model accuracy and cutting control parameters are analyzed.Upon axial and radial forces models,two optimal combinations of cutting control parameters are obtained for processing a13mm hole,corresponding to the minimum axial force and the radial force respectively.Finally,each optimal combination is applied in verification experiment.The verification experiment results of cutting force are in good agreement with prediction model,which confirms accracy of the research method in practical production.
文摘Ciprofloxacin is a second-generation of fluoroquinolone,broad-spectrum antibiotic with bactericidal activity against Gram-positive and Gram-negative organisms.It is one of the most widely used antibiotics,because of its efficacy,safety,and relatively low cost.Ascorbic acid(vitamin C)is water-soluble monosaccharide antioxidant;it is essentially required by the body for its various biochemical and physiological processes.S.aureus is Gram-positive cocci;widely distributed in the environment,it is a member of the normal flora of the body.S.aureus is not always pathogenic;it is a common cause of skin infections including abscesses,respiratory infections such as sinusitis,and food poisoning.E.coli is Gram-negative bacteria,found in the environment,foods,and intestines.Most E.coli strains are harmless;it is part of the normal microbiota of the gut.However,some serotypes of E.coli cause serious food poisoning in their hosts;it can cause diarrhea,while others cause urinary tract infections,respiratory illness and pneumonia,and other illnesses.Method:Cup cut diffusion method was applied.Experiment I:is carried out to choose the concentration of vitamin C to be used in experiment II.The negative control is normal saline,added in cup in each plate,vitamin C(100 mg/mL,200 mg/mL,400 mg/mL)was added,the volume in each cup was 100μL.Experiment II:Eight groups of treatments were applied.The first is the negative control(1%normal saline),the second group is the positive control of vitamin C(200 mg/mL).The third,fourth and fifth groups are ciprofloxacin with different concentrations(10 mg/mL,20 mg/mL,40 mg/mL);the sixth,seventh and eighth are the combination of vitamin C with each concentration of ciprofloxacin(10 mg/mL,20 mg/mL,40 mg/mL).Each group includes six petri dishes.Bacterial plates were incubated at 37 oC for 24 h and 48 h.Zone of inhibition is measured in mm.Results and conclusion:Ciprofloxacin produces dose dependent increase in zone of inhibition of S.aureus and E.coli growth,after 24 and 48 hours incubation.While vitamin C in the concentration used produced inhibitory effect on the growth of S.aureus and E.coli,after 24 hours incubation,vitamin C effect was not changed after 48 hours incubation.After 24 hours incubation,vitamin C potentiated the effect of ciprofloxacin at low concentration(10 mg/mL);while vitamin C antagonized the effect of ciprofloxacin at higher concentrations(20 and 40 mg/mL)on S.aureus growth.In the same time,ciprofloxacin antagonized the inhibitory effect of vitamin C on S.aureus growth.After 48 hours incubation,S.aureus produced resistance against ciprofloxacin alone,and that combined with vitamin C compared to zone of inhibition after 24 hours.Ciprofloxacin produced dose dependent inhibition of E.coli growth after incubation for 24 and 48 hours.Vitamin C potentiated the inhibitory effect induced by ciprofloxacin(additive effect).The inhibitory effect of ciprofloxacin,vitamin C and the combination was not changed after 48 hours compared to 24 hours.
基金funded jointly by the Scitech R&D Program of Chongqing Municipality(cstc2014yykfA00002(cstc2014yykfA0234),cstc2014jccxA0028 and cstc2013ggB0011)the Spark Program of Earthquake Sciences of CEA(Grant No.XH14042)
文摘A M_L3.8 earthquake occurred on February 23,2014 in Rongchang County,which is located at the southern edge of the Sichuan Basin in the border area between Sichuan and Chongqing. This paper presents results of focal mechanism solution of this earthquake using the CAP( cut and paste) method based on broadband seismograms recorded by regional seismic stations. Our results show that the moment magnitude is M_W3. 09 and focal depth is 3km. The hypocenter of this earthquake is located close to a buried fault in the Luoguangshan anticline. Oil prospecting and deep drilling data indicate that this buried fault is a thrust fault,striking SW230°,dipping NW45°,and 1. 7km deep. There are some injection wells within the anticline,and significant injection-induced earthquakes were observed during the periods of injection of waste water into the deep formations through those wells. The best double couple solution of the M_L3.8 earthquake is 247°,48°and 104° for strike,dip and rate,respectively,for one nodal plane( and 46°,44° and 74°for another nodal plane),which is in agreement with the geometry of the buried fault.Therefore,we conclude that the M_L3.8 Rongchang earthquake is possibly the result of faulting along the buried reverse fault induced by water injection under the compressive stress regime in the area.
文摘The kineto-elastodynamic(KED) model of a hose cutting mechanism used in the aluminum electrolytic capacitor(AEC) casing machine is developed to investigate the dynamic characteristics. According to the composition characteristics, the cutting mechanism is divided into cam-roller and linkage two substructures. And the dynamic models of the two substructures are established using the lumped parameter method and finite element method(FEM), respectively. In the model, the compliances of the camshaft and the links are taken into consideration. The elastic displacement of the links, angular error of the cutter and the dynamic stress of the links are analyzed based on the KED model. The results provide important information for structure optimization and vibration control of the mechanism.
文摘The dynamic performances of an ultra-precision fly cutting machine tool(UFCMT)has a dramatic impact on the quality of ultra-precision machining.In this study,the dynamic model of an UFCMT was established based on the transfer matrix method for multibody systems.In particular,the large-span scale flow field mesh model was created;and the variation in linear and angular stiffness of journal and thrust bearings with respect to film thickness was investigated by adopting the dynamic mesh technique.The dynamic model was proven to be valid by comparing the dynamic characteristics of the machine tool obtained by numerical simulation with the experimental results.In addition,the power spectrum density estimation method was adopted to simulate the statistical ambient vibration excitation by processing the ambient vibration signal measured over a long period of time.Applying it to the dynamic model,the dynamic response of the tool tip under ambient vibration was investigated.The results elucidated that the tool tip response was significantly affected by ambient vibration,and the isolation foundation had a good effect on vibration isolation.