Cavity formation in cross-wedge rolling processes

The problem of end-face cavity formation in parts produced by cross-wedge rolling was studied in order to reduce material consumption.The cavity depth was measured by the displacemern method.Twenty-one different cases of rolling were analysed by finile element method to determine the effects of process parameters such as the wedge tool angle,the temperature of material,the tool velocity and the reduction ratio on the depth of end-face cavities.Relationships between these parameters are examined in order to establish depe ndencies enabling quick and simple selection of a con cavity allowance in order to remove the cavities.The equations for calculating the con cavity allowance were verified in an experimental process for manufacturing ball pins with the use of flat tools.Rolling tests were performed using a billet with its length selected in compliance with the established dependencies.The experimental results demonstrate that the proposed solution is a viable method for end-face cavity removal.

Improvement of Temperature Drop Model Parameters for 4200mm/3500mm Rolling of Baosteel Medium and Thick Plate

Based on the temperature situation during the rolling process of 4200 mm/3500 mm medium and thick plates at Baosteel,this article analyzes the influencing factors of temperature changes during the rolling process from the perspective of heat transfer theory and the temperature change law during the rolling process.The temperature loss during the four rolling processes is tracked on site,and the temperature drop model parameters during the rolling process of 4200mm/3500mm medium and thick plates at Baosteel are quantitatively provided.It is applied to actual rolling production and has achieved good results.

NUMERICAL SIMULATION OF ROUND TO OVAL ROLLING PROCESS

Three dimensional thermal-mechanical coupled elasto-plastic FEM has been used for simulation of round to oval single pass rolling. The analysis was conducted using MARC/AUTOFORCE1. 2 code. The material is assumed to be elasto-plastic and it obey the Von Mises yield criterion and Prandtl- Reuss rule. Deformation of the workpiece is simulated in a step-by-step manner,updating the coordinates of material points and the property after each step, so that both nonsteady-state and stendy-state deformation can be simulated. The heat transfter between the workpiece, the rolls, and enviroment and the heat generation due to plastic work and friction force, are considered in the analys- is.Predicted the deformation shape of the workpiece, distributions of strains, stresses, strain rates and temperatures, roll-separating force and roll torque are presented.

Behavior of Transversal Crack on Slab Corner During V-H Rolling Process

The behavior of transversal cracks on the surface of the slab corner during vertical and horizontal （V-H） rolling process with flat vertical roll and groove vertical roll was simulated by explicit dynamic finite element method. The closure and growth of crack and the contact pressure on surfaces of the crack in contacting zone between slab and roll during rolling process were analyzed. The results showed that during vertical rolling process, when the groove vertical roll is used, the maximum contact pressure on surfaces of the crack is 115 MPa, and the closure of crack is stable when the flat vertical roll is used, the maximum contact pressure on surfaces of the crack is 70 MPa, and it fluctuates greatly. During horizontal rolling process, when groove vertical roll is used, the contact pressure becomes zero which may accelerate the growth of crack when flat vertical roll is used, there is still contact pressure. The cal culated results are in good agreement with the results of test.

Controlled Rolling and Cooling Process for Low Carbon Cold Forging Steel

Effect of controlled rolling and cooling process on the mechanical properties of low carbon cold forging steel was investigated for different processing parameters of a laboratory hot rolling mill. The results show that the specimens with fast cooling after hot rolling exhibit very good mechanical properties, and the improvement of the mechanical properties can be attributed mainly to the ferrite-grain refinement. The mechanical properties increase with decreasing final cooling temperature within the range from 670 ℃ to 570 ℃ due to the finer interlamellar spacing of pearlite colony. The specimen with fast cooling after low temperature rolling shows the highest values of the mechanical properties. The effect of the ferrite grain size on the mechanical properties was greater than that of pearlite morphology in the present study. The mechanical properties of specimens by controlled rolling and cooling process without thermal treatment were greatly superior to that of the same specimens by the conventional rolling, and their tensile strength reached 490 MPa grade even in the case of low temperature rolling without controlled rolling. It might be expected to realize the substitution medium-carbon by low-carbon for 490 MPa grade cold forging steel with controlled rolling and cooling process.

STUDY OF DYNAMIC RECRYSTALLIZATION OF LOW CARBON STEEL IN THIN SLAB CONTINUOUS ROLLING PROCESS

Combined with the technological characteristics of thin slab continuous rolling process （TSCR）, dynamic recrystallization of an extremely coarse austenite of low carbon steel is studied by Thermecmaster-Z hot simulator. By the analysis of true stress-strain curves and the observation of microstructures at different deformation stages, the critical stress and critical strain are determined under different deformation conditions. The effect of Z parameter on dynamic recrystallization of coarse austenite is studied. The microstructure evolution in real production is also discussed.

DANIELI concepts and experiences in thin slab casting and rolling technology for HRC production—the evolution of a winning process route to face increasing market requirements

The direct rolling process for hot strip production,where the thin slab caster is connected directly to the mill,has gained market share rapidly because of its remarkable advantages in terms of energy savings and investment cost over the conventional hot strip mills. However,the unquestionable advantages of the first-generation applications of this plant concept also entail significant limitations both in productivity and steel grades that can be produced. Since his first pioneering applications,Danieli considered strategic the development of new technical solutions specifically conceived to overcome these limitations with the goal of increasing plant production volumes and enlarging steel grade product mix,in order to cover the gap between "Conventional mill" and "Thin slab casting and rolling" process routes. In order to reach this goal,Danieli has developed a complete portfolio of plant lay outs adopting Thin Slab Casting and Rolling technologies,each of them conceived to guarantee the optimal CAPEX and OPEX parameters in fitting with market requirements our Customer intend to target.in terms of productivity,steel grades and coil dimension product mix. Danieli TSR(Thin Slab Rolling) fTSR(flexible Thins Slab Rolling) QSP(Quality Strip Production) and ETR(Extra Thin Rolling) plant configurations are analyzed in this paper. With this diversified approach,Danieli solutions are most appropriate answers to thin slab casting and rolling to produce hot rolled coils with superior quality and an extremely diversified range of steel grades. Already,this approach has allowed Danieli plants to:①exceed the threshold production of 3.0 Mt/a with 2 casting strands in operation as done in Tangshan Iron and Steel plant in P.R.China since 2005;②expand the product mix to include virtually all the steel grades used for flat product applications,including the most demanding ones,such as peritectic(in Essar Algoma Canada and Benxi Iron and Steel,China),micro-alloyed,and silicon steels,for the most sophisticated applications,such as automotive and pipe manufacturing,including Arctic applications,(as done in OMK plant in Russia);③extend the range of final strip thicknesses to include ultra thin gauges,down to 0.8 mm(as in Ezz Flat Steel,in Egypt).

Influence of Ultrasonic Surface Rolling Process and Shot Peening on Fretting Fatigue Performance of Ti-6Al-4V

At present,there are many studies on the residual stress field and plastic strain field introduced by surface strengthening,which can well hinder the initiation of early fatigue cracks and delay the propagation of fatigue cracks.However,there are few studies on the effects of these key factors on fretting wear.In the paper,shot-peening(SP)and ultrasonic surface rolling process(USRP)were performed on Ti-6Al-4V plate specimens.The surface hardness and residual stresses of the material were tested by vickers indenter and X-ray diffraction residual stress analyzer.Microhardness were measured by HXD-1000MC/CD micro Vickers hardness tester.The effects of different surface strengthening on its fretting fatigue properties were verified by fretting fatigue experiments.The fretting fatigue fracture surface and wear morphology of the specimens were studied and analyzed by means of microscopic observation,and the mechanism of improving fretting fatigue life by surface strengthening process was further explained.After USRP treatment,the surface roughness of Ti-6Al-4V is significantly improved.In addition,the microhardness of the specimen after SP reaches the maximum at 80μm from the surface,which is about 123%higher than that of the AsR specimen.After USRP,it reaches the maximum at 150μm from the surface,which is about 128%higher than that of AsR specimen.It is also found that the residual compressive stress of the specimens treated by USRP and SP increases first and then decreases with the depth direction,and the residual stress reaches the maximum on the sub surface.The USRP specimen reaches the maximum value at 0.18 mm,about−550 MPa,while the SP specimen reaches the maximum value at 0.1 mm,about−380 MPa.The fretting fatigue life of Ti-6Al-4V effectively improved after USRP and SP.The surface integrity of specimens after USRP is the best,which has deeper residual compressive stress layer and more refined grain.In this paper,a fretting wear device is designed to carry out fretting fatigue experiments on specimens with different surface strengthening.

Effect of gradient temperature rolling process on promoting crack healing in Q500 heavy plates

To ensure the quality of heavy plate products as determined by ultrasonic inspection, it is necessary to effectively control defects such as cracks and shrinkage cavities in heavy plates. Generally, some defects such as large size cracks exist due to insufficient deformation in the center of traditionally rolled plates. Compared with the traditional rolling process, gradient temperature rolling(GTR) process can effectively increase deformation inside heavy plates. In this study, the effect of GTR on crack healing was analyzed through a comparison experiment with the uniform temperature rolling(UTR). The results show that the GTR process could increase the plastic strain inside the heavy plate and effectively promote the healing process of the preset cracks. The degrees of crack healing at the center and quarter thickness position of the steel plate via GTR were greater than twice those of the plate via UTR. The GTR process can significantly reduce the internal defects of heavy plates and improve the defect detection level of heavy plate products. Also, The GTR process results in the formation of new crystal grains in the crack region, which is crucial to crack healing.

Effect of Rolling Process on Comprehensive Properties of Corrosion Resistant Steel for Bottom Plate of Cargo Oil Tanks

A new kind of corrosion resistant steelfor cargo oiltanks（COT）was developed.The influences of finalrolling temperature,cooling rate,and finalcooling temperature on microstructure were investigated.The proper rolling process parameters were obtained through multi-pass thermalsimulation test.The finalrolling temperature is about 820 ℃,the finalcooling temperature is about 600 ℃,and the cooling rate should be controlled between 10 ℃/s and 20 ℃/s.Based on the above analysis of the results,three groups of rolling samples by thermo mechanicalcontrolprocess are prepared.The tensile strength,yield strength,and toughness of the corrosion resistant steelare measured,which meet the requirements of DH36 steel,it can instruct the actualrolling production.The corrosion behaviour is also researched by weight loss and electrochemicalimpedance spectroscopic method,and it is found that the steelhas good corrosion resistance performance,the best one is No.3 steel,the corrosion rate of which is about 1/4 of the accepted criterion.

Head Curvature of Pure Titanium Sheet Influenced by Process Parameters and Controlling in Hot Rolling Process

We investigated the influences of process parameters on the head curvature of pure titanium sheet in hot rolling process and proposed the controlling means. First, the thermal simulation experiments for pure titanium TA1 were carried out to investigate the hot deformation behaviors of pure titanium in the temperature range of 700-800 ℃ with strain rate range of 1-20 S-1, and the processing map was established to determine optimized deformation parameters. Then, the finite element model has been constructed and used to analyze the effect of process parameters on the direction and severity of head curvature of pure titanium sheet. The process parameters considered in the present study include workpiece temperature, work roll diameter, pass reduction, oxide scale thickness of workpiece surface, and interface friction coefficient. The simulation results show that the workpiece temperature and the interface friction coefficient are the two main factors. The proposed controlling means was carried out on a hot rolling production line and solved the head curvature problem effectively. The rolling practices indicate that the rolling yield is improved greatly.

Influence of a multi-step process on the thickness reduction error of sheet metal in a flexible rolling process

Flexible rolling is a forming process based on thickness reduction, and the precision of thickness reduction is the key factor affecting bending deformation. The major purpose of the present work is to solve the problem of bending deformation error caused by insufficient thickness reduction. Under the condition of different rolling reductions with the same sheet thickness and the same thickness reduction with different sheet thicknesses, the thickness reduction error of sheet metal is analyzed. In addition, the bending deformation of sheet metal under the same conditions is discussed and the influence of the multi-step forming process on the thickness reduction error is studied. The results show that, under the condition of the same sheet thickness, the thickness reduction error increases with increasing rolling reduction because of an increase in work hardening. As rolling reduction increases, the longitudinal bending deformation decreases because of the decrease of the maximum thickness difference. Under the condition with the same thickness reduction, the thickness reduction error increases because of the decrease of the rolling force with increasing sheet thickness. As the sheet thickness increases, the longitudinal bending deformation increases because of the increase in the maximum thickness difference. A larger bending deformation is divided into a number of small bending deformations in a multi-step forming process, avoiding a sharp increase in the degree of work hardening; the thickness reduction error is effectively reduced in the multi-step forming process. Numerical simulation results agree with the results of the forming experiments.

Processing of commercial magnesium alloys by different-speeds-rolling technique

The commercial pure magnesium, AZ31 and AM60 alloys have been processed by a different-speeds-rolling (DSR) technique in order to estimate the possibility of producing high performance magnesium sheets by severe plastic deformation process. The experiment was carried out on a mill of which the rotation speed ratio of the upper roll to the lower roll could be varied from 1 to 1.364. Temperature of the two rolls of the mill could also be automatically controlled from room temperature to 300℃. The started billets with thickness of 10mm were cut from the cast ingot. The rolling parameters such as preheating temperature of the billet, rolling reduction per pass, rotation speed ratio and temperature of the rolls were carefully designed depending on the processed magnesium alloy. Mechanical properties of the successfully rolled sheets with final thickness of about 1mm were characterized, corresponding to microstructure development during the DSR-processing. The potential application of DSR to processing of magnesium alloys was discussed.

Formation Mechanism in Alloy Steel Rolling Process Using Thermo-mechanical Coupling Method

Based on the theory of elastic-plastic finite element method, the high-speed hot continuous rolling process of a billet is simulated and analyzed in vertical and horizontal passes. The billet is dragged into the passes by contact friction force between the billet and rollers. The rollers and billet are represented by respectively rigid and deformable bodies, and three-dimensional models are developed for the billet and rollers. The distribution of deformation field, effective strain, rolling force and temperature field are accurately calculated for the whole rolling process （including unstable and stable stages）. In addition, the rolling pressure on the width symmetry center is compared with that in the in-situ experimental measurements. It is revealed that various heat exchange phenomena among the billet, rollers and surroundings can result in unbalanced temperature distribution on the cross section. Rolling force and strain can change significantly when the billet is moved towards or away from the roller gap, and keep almost invariable in the stable stage. It is expected that the simulation results would be useful for practical manufacture and provide the theoretical foundation for improvement of process planning and optimization of process parameters.

Mathematical model for cooling process and its self-learning applied in hot rolling mill

Control precision of coiling temperature is one of the key factors affecting the profile shape and surface quality during the cooling process of hot rolled steel strip.For this reason,the core of temperature control precision is to establish an effective cooling mathematical model with self-learning function.Starting from this point,a cooling mathematical model with nonlinear structural characteristics is established in this paper for the cooling process of hot rolled steel strip.By the analysis of self-learning ability,key parameters of the mathematical model could be constantly corrected so as to improve temperature control precision and adaptive capability of the model.The site actual application results proved the stable performance and high control precision of the proposed mathematical model,which would lay a solid foundation to improve the steel product qualities.

Optimization of Rolling Process for Bi(2223)/Ag Superconducting Tapes by a Statistical Method

Ag-sheathed (Bi,Pb)(2)SoCa(2)Cu(3)O(x) tapes were prepared by the powder-in-tube method. The influences of rolling parameters on superconducting characteristics of Bi(2223)/Ag tapes were analyzed qualitatively with a statistical method. The results demonstrate that roll diameter and reduction per pass significantly influence the properties of Bi(2223)/Ag superconducting tapes while roll speed does less and working friction the least. An optimized rolling process was therefore achieved according to the above results.

Study on the rolling process for thin HSLA heavy plates

Analyzed and studied the characters of high strength low alloy steel which contain Mo,Cr,Nb and Ni.etc.Following actual rolling,combining the feature of rolling mode,and exploiting the equipment advantage of 5 m Heavy Plate Mill,optimized the material design,heating temperature and rolling method, stabilized rolling process of thin alloyed steel,the quality index was advanced.

Effect of Rolling Process on Microstructure and Wear Properties of High Carbon Equivalent Gray Cast Iron

Rolling process based on the plastic deformation as a surface strengthening treatment was employed,aiming to improve the wear resistance ability and functional performance of the high carbon equivalent gray cast iron(HCEGCI).The microstructures and tribological performance of the untreated and rolled samples were characterized.In addition,the wear mechanism of HCEGCI samples was also studied via pin-on-disc tests.The experimental results show that the as-rolled samples possess the structure-refined layer of 15μm and work-hardened layer of 0.13 mm.In comparison with the surface hardness of untreated samples,the surface hardness of as-rolled samples increases by 84.6%(from 240HV0.1 to 443HV0.1)and the residual compressive stresses existed within the range of 0.2 mm.The wear rates of as-rolled samples were decreased by 38.4%,37.5%,and 44.4%under different loads of 5 N,10 N,and 15 N,respectively.The wear characteristics of the untreated samples mainly exhibit the peeling wear coupled with partial adhesive and abrasive wear.However,as for the as-rolled samples,the adhesive wear was limited by the structure-refined layer and the micro-crack propagation was controlled by the work-hardened layer.Therefore,the wear resistance of as-rolled samples can be improved significantly due to the low wearing degree of the friction contact zone.

Two-stage treatment process of pickling wastewater in the cold-rolling production of stainless steel

Based on the characteristics of pickling wastewater in the cold-rolling production of stainless steel, a new processing route, featuring source sludge reduction, wastewater two-stage treatment, heavy metal-contained sludge and calcium salt sludge separating recovery, was proposed. As shown by the research results, after the two-stage process treatment, the effluent water can steadily reach the emission standards, the sludge yield can be decreased by more than 8% ; within the heavy metal-contained sludge, the recovery rates of Fc,Cr and Ni can either reach or surpass 95% ,and the total content ofF and S can drop to around 3%. Therefore,the sludge in the front part can be used as ferric dust. In the calcium salt sludge ,the recovery rate of F can either reach or surpass 85% ,and the total contents of Fe,Cr and Ni can fall below 0.5%. So the sludge in the rear part can be used as fluorgypsum or fluorite. Meanwhile,the results of the analysis on heavy metals leaching toxicity and morphologic distribution indicate that the two kinds of sectionalized sludge are not classified as hazardous wastes, which have a stable behavior and better utilization values compared with the former mixed- sludge.

Rolling Gaussian Process Regression with Application to Regime Shifts

Gaussian Process Regression (GPR) can be applied to the problem of estimating a spatially-varying field on a regular grid, based on noisy observations made at irregular positions. In cases where the field has a weak time dependence, one may desire to estimate the present-time value of the field using a time window of data that rolls forward as new data become available, leading to a sequence of solution updates. We introduce “rolling GPR” (or moving window GPR) and present a procedure for implementing that is more computationally efficient than solving the full GPR problem at each update. Furthermore, regime shifts (sudden large changes in the field) can be detected by monitoring the change in posterior covariance of the predicted data during the updates, and their detrimental effect is mitigated by shortening the time window as the variance rises, and then decreasing it as it falls (but within prior bounds). A set of numerical experiments is provided that demonstrates the viability of the procedure.