基于MCS-SBL算法的配电网故障定位方法

配电网拓扑结构复杂,传统方法往往需要大量测点信息且难以实现快速有效的故障定位,本文提出基于少量测点信息的故障定位方法。首先,利用等效原理建立一个欠定的故障节点电压方程;其次,利用多重测量向量模型的贝叶斯压缩感知算法求解方程,根据重构稀疏电流矩阵的非零元素位置求解故障区域,实现故障定位;最后,在IEEE33节点配电系统上进行仿真实验,结果表明,所提方法仅需要少量测点的故障前后正序电压分量便可有效定位故障,计算速度较快,并且基本不受故障类型、过渡电阻的影响,同时适用于单故障和多重故障的场景,具有较强的抗噪能力。

An Improvement on Current Sharing Characteristics of Poloidal Field (PF) AC-DC Converters

In response to the current imbalance phenomenon and its harmfulness, a current sharing circuit model is built up, which reveals the underlying causes for the current imbalance through a quantitative analysis. Then, a feasible approach of improvement, namely enlargement of the length of connection busbars, is proposed. After the amendment, it can be seen that the current sharing coefficient is ahnost unity under rated or fault current conditions.

The Awkward Sharing Economy:Its Status Quo and Prospect

This paper comprehensively analyzes the origins,current situation,and prospects of the sharing economy.The primary purpose is to present the issues and challenges confronting the sharing economy at its current,awkward stage of development and to make reasonable speculations about its future.The research is based on academic literature on the sharing economy from both domestic and international sources.The findings indicate that despite current shortcomings in the regulatory system,industry structure,and user behavior,the scope of the sharing economy’s applications could still expand,and its technology could continue to advance.Overall,the prospects for the sharing economy are likely to be promising.

Current Sharing Temperature Test and Simulation with GANDALF Code for ITER PF2 Conductor Sample

Cable-in-conduit conductor （CICC） conductor sample of the PF2 coil for ITER was tested in the SULTAN facility. According to the test results, the CICC conductor sample exhibited a stable performance regarding the current sharing temperature. Under the typical operational conditions of a current of 45 kA, a magnetic field of 4 T and a temperature of 5 K for PF2, the test result for the conductor current sharing temperature is 6.71 K, with a temperature margin of 1.71 K. For a comparison thermal-hydraulic analysis of the PF2 conductor was carried out using GANDALF code in a 1-D model, and the result is consistent with the test one.

Current Sharing Analysis of Arm Prototype for ITER PF Converter Bridge

A bridge arm prototype of ITER poloidal field （PF） converter modules has been designed and fabricated. Non-cophase counter parallel connection is chosen as the arm structure of the prototype. Among all factors affecting current sharing, arm structure is the main one. During the design of the arm prototype, a novel method based on inductance matrixes is employed to improve the current sharing of the bridge arm. The test results on the prototype show that the current sharing performance of the arm prototype is much better than relevant design requirement, and that the matrix method is very effective to analyze and solve the current sharing problems of thyristor converters.

Study on the Current-Sharing Control System of the TF Power Supply for a Superconducting Tokamak

The superconducting toroidal field （TF） plays an important role in a superconducting tokamak, whose power supply was developed based on the feedback control principle. In this paper, superconducting tokamaks in different countries are described, and the TF power supply of the International Thermonuclear Experimental Reactor （ITER） is taken as an example to study the current-sharing characteristics in the current-stabilized stage. Firstly, the mathematical model of the TF power supply is established, and then the 3-loop control method is put forward for achieving the stability and reliability of current-stabilization and current-sharing. Furthermore, further studies indicate that the current-sharing controller has no influence on the current-stabilized control, and current-stabilizing and current-sharing can be realized at the same time. All the work done provides valuable references for the current-sharing design of the TF power supply for a superconducting tokamak, and all these studies lay a solid foundation for developing superconducting tokamaks.

Current Sharing Technology in Transmission Conductors of Cold Dielectric High Temperature Superconducting Cables Using Second-generation HTS Wires

冷绝缘高温超导电缆的导电层一般设计为多层结构以满足大电流载流特性，但伴随层数的增加，超导体上的集肤效应会引起电缆输电导体各层电流分布不均匀的问题，从而造成电缆损耗增加和传输性能下降。采用基于动态惯性权重因子的粒子群优化算法，提出了电缆导体层电流层间均流优化的设计方法。应用第2代高温超导材料钇钡铜氧涂层导体，通过建立超导电缆的等效电路模型，考虑电场、磁场等约束因素，对一根1km长，110kV／3kA等级的冷绝缘高温超导电缆进行优化设计，获得了电缆本体结构参数及输电导体层和屏蔽层的电流分布。比较优化前后层电流的结果可知，优化后超导电缆各导体层电流与平均电流相比最大不平衡率小于3．5％，各屏蔽层电流达到均布，较好地实现了电缆各导体层电流均匀分布的优化目标。最后，超导模型样缆载流特性实验也验证了优化设计方法的有效性。

Torque Sharing Function Control of Switched Reluctance Machines with Reduced Current Sensors

This paper presents a Torque Sharing Function(TSF)control of Switched Reluctance Machines(SRMs)with different current sensor placements to reconstruct the phase currents.TSF requires precise phase current information to ensure accurate torque control.Two proposed methods with different chopping transistors or a new PWM implementation require four or two current sensors to replace the current sensors on each phase regardless of the phase number.For both approaches,the actual phase current can be easily extracted during the single phase conducting region.However,how to separate the incoming and outgoing phase current values during the commutation region is the difficult issue to deal with.In order to derive these two adjacent currents,the explanations and comparisons of two proposed methods are described.Their effectiveness is verified by experimental results on a four-phase 8/6 SRM.Finally,the approach with a new PWM implementation is selected,which requires only two current sensors for reducing the number of sensors.The control system can be more compact and cheaper.

A Temperature-Based Hysteresis Buck Converter for Dynamic Current Sharing

In this study, a temperature-based current sharing strategy rather than equal sharing for loads was applied to promote the reliability of uninterruptible power systems (UPS). According to the temperature of each power supply module in a UPS, it would be better to reduce the output current ratio for a hotter supply module in the UPS. In this design, we implemented our regulation circuits by the UMC 0.25-μm CMOS technology with an input range from 3 V to 4.2 V and the regulated output at 1.1 V. The rated output current was 100 mA for each phase. We also employed a current-mode error-correction circuit to improve the current sharing performance based on the averaged current of each phase at the same temperature. According to our simulation results, the current sharing error can be restricted within ± 5% for the supply modules at the same temperature in our system.

Active Current Sharing of LCLC Resonant Converter with Switch-Controlled-Capacitor Technology

In this paper,an interleaved LCLC converter with enhancement-mode(E-mode)GaN devices is introduced to achieve the accurate current sharing performance for data center applications. Any tolerance in the resonant tank elements can lead to large load imbalance between any two different phases. Due to the steep gain curves of LCLC converters,conventional current sharing methods are not effective. In the proposed converter,the impedances of the resonant networks are matched by switching a capacitor,i.e.,switch controlled capacitor(SCC),in series with the resonant capacitor in one or some of the phases,which results in accurate load current sharing among the phases with an accuracy around 0.025%. The load share of a phase is sensed through the resonant current on it,and the control logic applied to such current sharing can be achieved. By this method,accurate current sharing is achieved for a wide input voltage range required for the hold-up time in data center applications. Interleaving is applied in the proposed multiphase LCLC converter,resulting in low current stress on the output capacitor and allowing ceramic capacitor implementation. Moreover,phase shedding accomplishes high light load efficiency. The performance of the proposed interleaved LCLC converter is verified by a two-phase 1 k W prototype with an input voltage ranging from 250 V to 400 V and a fixed 12 V output voltage.

An Adaptive Wireless Power Sharing Control for Multiterminal HVDC

Power sharing among multiterminal high voltage direct current terminals(MT-HVDC)is mainly developed based on a priority or sequential manners,which uses to prevent the problem of overloading due to a predefined controller coefficient.Furthermore,fixed power sharing control also suffers from an inability to identify power availability at a rectification station.There is a need for a controller that ensures an efficient power sharing among the MT-HVDC terminals,prevents the possibility of overloading,and utilizes the available power sharing.A new adaptive wireless control for active power sharing among multiterminal(MT-HVDC)systems,including power availability and power management policy,is proposed in this paper.The proposed control strategy solves these issues and,this proposed controller strategy is a generic method that can be applied for unlimited number of converter stations.The rational of this proposed controller is to increase the system reliability by avoiding the necessity of fast communication links.The test system in this paper consists of four converter stations based on three phase-two AC voltage levels.The proposed control strategy for a multiterminal HVDC system is conducted in the power systems computer aided design/electromagnetic transient design and control(PSCAD/EMTDC)simulation environment.The simulation results significantly show the flexibility and usefulness of the proposed power sharing control provided by the new adaptive wireless method.

一种优化开关磁阻电机换相区控制策略的高效率转矩分配函数

转矩分配函数被广泛应用于抑制开关磁阻电机的转矩脉动。然而,输入相转矩跟踪不足或者输出相产生较大的负转矩这两种情况通常会导致电机的转矩脉动难以得到有效抑制,并降低电机的运行效率。因此,为了能够有效降低电机的转矩脉动并提高电机的效率,提出了一种新型的转矩分配函数控制策略。在提出的转矩分配函数控制策略中,电机的换相区域分为两个区域。在前一区域中,通过降低输入相转矩分配的比例,可以实现输入相实际转矩快速跟踪参考转矩,电机的转矩脉动有效降低。同时由于在输入相电感变化率较低时减少输入相分配的转矩,从而输入相的峰值电流随之降低,电机的转矩电流比提高。在后一区域中,将输出相的电流在转子对齐位置附近处减小到0,以避免产生较大的负转矩。因此,在所提出的方案下,电机的转矩脉动得到有效抑制,电机的效率也得到了提高。为了验证该方法的有效性,在一台12/8三相开关磁阻电机上进行了仿真和实验。结果表明,所提出的转矩分配函数控制策略能有效降低开关磁阻电机转矩脉动,也能有效地提高开关磁阻电机的运行效率。

基于COMSOL Multiphysics的OPGW耐雷性能分析与仿真

为了研究光缆结构的改变对光纤复合架空地线(optical fiber composite overhead ground wire, OPGW)雷击断股的影响,应用COMSOL Multiphysics软件对其雷击点局部进行仿真,通过施加不同大小的雷击电流A、B、C分量以及改变架空地线的结构,对光纤复合架空地线进行雷击断股特性分析。结果表明:雷击电流的A、B、C分量中C分量的破坏性最强,B分量破坏性最弱。A、B分量同时作用时,产生的最高温度高于单独A分量作用的结果。外股层半径每增加0.05 mm,仿真结果最高温度下降约20℃;外股导线半径每增加0.05 mm,仿真结果最高温度下降约25℃。仿真结果为优化光纤复合架空地线结构参数、提升耐雷性能提供了理论支撑。

双路电源的主动均流电路系统研究

广泛使用的低成本电源管理芯片或直流电源模块通常并未集成输出均流控制功能,因此不能直接并联输出使用。而使用特殊的电源管理芯片或是额外的均流控制电路会提高电源电路的复杂程度,造成电路成本的提高。针对此应用场景,提出了一种具有主动均流功能的双路电源开关,作为负载开关或电源多路复用器应用于电路之中,利用开关电流的方法均分输出电流,在几乎不增加电路成本的同时对两路电源进行均流。阐述了所提双路电源开关的工作原理与参数设计方法,并通过仿真与实验证明了所提方法的正确性与可行性。

基于自适应虚拟电阻的低压微电网有功均分下垂控制策略

由于低压微电网中各分布式电源的线路阻抗不匹配,传统的下垂控制策略难以按照下垂系数合理分配有功功率。为此,提出一种无需通信的自适应虚拟电阻下垂控制方法。通过将微电网中每个分布式发电机(DG)单元输出的有功功率和电压传送给自适应虚拟电阻控制器中,在保证电压和频率稳定控制的前提下实现功率按逆变器容量比例进行精确分配。论文对改进方法的微电网逆变器进行小信号稳定性分析,以优化控制器有关控制参数。仿真和实验结果验证了所提控制方法的有效性。

串并联型海上风电场机组均压控制

针对串联型风机簇产生弃风的问题,在直流侧添加基于超级电容的储能单元,并在串联簇中设置一台参考机组,通过控制双向DC/DC变换器的吸收、释放电能,使同串联簇中除参考机组之外的其他机组向直流汇集母线上输出的功率相同,使直流风机风电功率和风机出口电压一致,实现基于超级电容储能的直流机组的均压控制,以此减少直流风机串联簇各机组间的风电功率差,降低弃风率。针对传统两相DC/DC变换器电感电流纹波大,两相电流不均衡等问题,采用了一种移相均流控制策略。最后,在Matlab/Simulink搭建了仿真模型,仿真结果验证了所提出的策略的有效性。

基于改进型转矩分配函数的开关磁阻电机转矩与峰值电流优化研究

开关磁阻电机(SRM)使用传统的转矩分配函数控制时由于转矩分配函数的开关角度恒定,使其在换相阶段出现较为明显的转矩脉动和较高的峰值电流现象。针对这一现象,提出实时调节开关角度的指数型转矩分配函数的控制方法来降低转矩脉动与相峰值电流。与传统的转矩分配控制进行比较分析,所提算法能够在不同电机转速下抑制转矩脉动和降低SRM定子绕组换相峰值电流,在中低速情况下,实时优化转矩分配函数开关角与重叠角,提高了SRM的运行效率。以一台2.2 kW的12/8开关磁阻电机作为控制对象,建立控制系统仿真模型,通过仿真和实验验证了所提算法的有效性。

IGBT并联应用均流控制技术综述

绝缘栅双极型晶体管IGBT(insulated-gate bipolar transistor)在现代电力电子技术中应用广泛,在某些单个器件性能达不到设计要求的工作场合,IGBT的并联使用成为一种经济可行的方法。多模块IGBT并联应用可以简化电路结构,增大变流器输出功率,提高装置功率密度。IGBT并联应用过程中,器件本体的动、静态特性及结温的差异,驱动电路结构及功率回路不对称性,伴随IGBT长期使用出现的老化或失效等问题,都会引起并联IGBT支路电流的不均衡,影响系统的可靠性和稳定性。对国内外IGBT并联应用所关注的研究热点进行了调研分析,总结了IGBT并联动、静态电流不均衡产生的原理及影响,分析了电流均衡控制原理的差异。从功率回路均流控制和驱动回路均流控制两个方面,对IGBT并联应用均流控制的工作特性进行了分析总结和技术对比,并对IGBT并联均流技术的发展方向进行了展望。

不同Cs、O电流比激活对GaAs光阴极灵敏度和稳定性的影响

鉴于不同的铯氧电流激活GaAs光阴极时会对激活过程和结果产生不同的影响,从而影响GaAs光阴极的灵敏度和稳定性。以固定铯源电流,改变氧源电流的方式获取不同铯、氧电流比,激活同类GaAs光阴极,得到了3组实验数据。对数据进行分析,结果表明:同类光阴极在相同条件下激活时,光电流出现的时间几乎一致,并且首个光电流峰值也非常接近;激活时ICs/IO=1.07是目前获得高灵敏度、高稳定性GaAs光阴极的最佳电流比,而ICs/IO=1.10时光阴极灵敏度低但稳定性好,ICs/IO=1.03时光阴极灵敏度高但稳定性差。双偶极层模型认为Cs、O激活后GaAs表面形成了稳定均匀的GaAs-O-Cs:Cs-O-Cs双偶极层,并达到了负电子亲和势,这一点与实验数据的分析结果相一致。该方法可用于提高GaAs光阴极灵敏度和稳定性。