A Novel High Output Resistance Current Source Based on Negative Resistance

This paper presents a novel scheme for enhancing resistance that utilizes an equivalent negative resistance. Adopting this novel scheme in the proposed current source could remarkably boost its output resistance without requiring increased power supply. Simulation with 0.6μm CMOS process models shows that the output resistance of the novel current source can reach the order of 10^9Ω with a 1.04GHz bandwidth and only 10.6ppm/℃ in the range of -40～145℃.

Carrier phase shifted SPWM based on current sourced multi-modular converter for active power filter

A novel current-source active power filter (APF) based on multi-modular converter with carrier phase-shifted SPWM (CPS-SPWM) technique is proposed. With this technique, the effect of equivalent high switching frequency con-verter is obtained with low switching frequency converter. It is very promising in current-source APF that adopt super-conducting magnetic energy storage component.

Theoretical analysis method for Howland current source design

The Howland current source （HCS） circuit is commonly used, e.g. in electrical impedance tomography （EIT） sys tems. It is important to optimise the design parameters, such as the output impedance, bandwidth, current stability and load range. While many people have used this circuit, it has not been systematically analysed. In this paper, a numerical method is proposed to analyse the characteristics of HCS. Based on a nonideal opamp model, general formulas and simplified for mulas for calculating the output impedance and the closeloop gain of HCS are deduced. From these formulas, the practical formulas are chosen and their effectiveness has been proven by analysis and experiment. The output impendence of two HCS circuits based on t^A741 and LM6365 are compared. The magnitudefrequency response and the relationship between the cur rent and the load of HCS are discussed.

Multilevel Current Source Converters for High Power Medium Voltage Applications

In medium voltage high power applications,multi-level current source converters(CSCs)are good candidate to increase system power region,reliability,and the quality of output waveforms.Compared with widely researched voltage source multi-level converters(MLCs),the current source MLCs have the advantages of inherent short-circuit protection,high power capability and high quality of output current waveforms.The main features of MLCs include reduced harmonics,lower switching frequency and reduced current stress on each device which is a particularly important for high power application with low voltage and high current requirements.This paper conducts a general review of the current research about MLCs in higher power medium voltage application.The different types of parallel structure based MLCs and the modulation methodologies will be introduced and compared.Specifically,the circuit analysis of the common-mode(CM)loop for parallel structures will be conducted,the common-mode voltage(CMV)and circulating current suppression methods developed on the base of multilevel modulations will be addressed.

Analysis of Symmetrical and Asymmetrical Current Source Multilevel Inverter

The paper proposes a Current Source Multilevel Inverter (CSMLI) with single rating inductor topology. Multilevel inverters are most familiar with power converter’s applications due to reduced dv/dt, di/dt stress, and very efficient for reducing harmonic distortion in the output voltage and output current. The proposed nine-level current source inverter has been tested under symmetrical and asymmetrical modes of operation, and their activities are compared using PI and Fuzzy PI (Proportional Integral) controllers with multicarrier PWM (Pulse Width Modulation) strategy. MATLAB/Simulink simulation has been made for the proposed converter to obtain its performance measures. Some experimental results are given to verify the presented Current Source Multilevel Inverter.

Model Predictive Control Circuit of the Current Source Matrix Converter

In this paper, a new predictive control strategy for current source matrix converter (CSMC) is presented. Proposed predictive control strategy allows for creating output voltages with boost type voltage transfer ratio and desired frequency. The description of predictive control circuit of the CSMC is presented. Furthermore the simulation test results to confirm functionality of the proposed control strategy and converter properties under this strategy are shown.

Comparisons and Improvements of Key Operating Characteristics of Current Source Converter Applied in HVDC System

Because of its controlled power factor and no commutation failure,current source converter(CSC)made up of reverse-blocking IGCTs(RB-IGCTs)offers broad application prospects in the field of HVDC system.Valve voltage and power operating range as the most important operating characteristics should be paid attention to but they are always contradictory.First,the relationship between valve voltage and modulation index is obtained.In particular,valve voltage of converter under the three typical modulation methods is compared,analyzed,and verified.Second,with the help of the independent control strategy and coordinated control strategy of both ends,power operating ranges of the three modulation methods are comprehensively analyzed and compared.Third,in order to solve power coupling at a low active power,the improved coordination control strategy at both ends in this paper is proposed and the relationships among active power,reactive power,DC current and phase angle difference are given in detail.Finally,a 500 kV/3 kA simulation system was built in PSCAD/EMTDC to obtain comparison results of the key operating characteristics of CSC under different modulation methods and the converter can realize unity power operation under random active power after adopting the improved coordinated control strategy,and DC current does not decrease to zero,verifying effectiveness of the coordinated control strategy.

A 3GHz Low-Power and Low-Phase-Noise LC VCO with a Self-Biasing Current Source

A fully integrated 3GHz low-power and low-phase-noise voltage-controlled oscillator （VCO） with a self-biasing current source was implemented in a standard 0.18μm CMOS process. A trade-off between noise and power was realized through the optimization of the improved current source. The VCO can be tuned from 2.83 to 3.25GHz with a 13.8% tuning range. The measured phase noise at 1MHz offset is -111dBc/Hz at a frequency of 3.22GHz while the core circuit draws less than 2mA from a 1.8V supply voltage. These results make the circuit suitable for a 5GHz wireless local area network （WLAN） receiver and 3.4 to 3.6GHz world interoperability for microwave access （WiMAX） application.

Intracellular and current source density analysis of pretectal input to the optic tectum of the frog

Objective Electrophysiological examination of the ipsilateral pretectotectal projection has proved that pretectal cells elicit strong suppressive responses to the ipsilateral tectum.However,the neural mechanisms underlying the contralateral pretectotectal prejection are still obscure.The present study aimed to examine the synaptic nature of pretectal nuclei and contralateral tectal cells,and to demonstrate the spatiotemporal pattern of neuronal activity in the 2 main brain structures. Methods Intracellular recording and current source density（CSD）analysis were used to test the complexity of neuronal mechanism of pretectotectal information transfer.Results The pretectal stimulation elicited only one type of response on the contralateral tectum,the inhibitory postsynaptic potential（IPSP）.The majority of contra-induced IPSPs were assumed to be polysynaptically driven.In the CSD analysis,only one sink with short latency was observed in each profile.The ipsilateral projection produced a prominent monosynaptic sink in layer 8 of tectum.Recipient neurons were located in layers 6 and 7 of tectum.The result confirmed former findings from ipsilateral intracellular recordings.Conclusion These results suggest the following neuronal circuit：afferents from the pretectal nuclei broadly inhibit both tectal neuron,and since no second sink occurs in tectal layers,the pretectotectal excitatory afferents probably do not extend over the whole tectum,but are within limited state.The results of intracellular recording and CSD analysis further provide evidence of how pretectal afferent activity flows within the tectal laminae.

CSI and CSI7 Current Source Inverters for Modular Transformerless PV Inverters

Current source inverter(CSI)is a class of power electronic converters that,thanks to the inherent boost capability and ease of control,is investigated for grid-tied photovoltaic power conversion applications.Traditional CSI and CSI7 topologies are here analyzed and compared with two kind of space vector modulation strategies mainly in terms of ground leakage current both in simulations and experiments.Furthermore,THD of the injected grid current and the computation of conduction and switching semiconductor power losses are also carried out in numerical simulations.The topology comparison is carried out with the use of a different number of PV modules,to analyze the robustness of the topologies to different size of the PV strings.Simulation and experimental results show that the CSI7 topology,with respect to conventional CSI,allows to strongly reduce ground leakage current,phase current THD and semicondutor power losses,at the price of an additional power device.

Recent Developments of Modulation and Control for High-Power Current-Source-Converters Fed Electric Machine Systems

The pulse-width-modulated(PWM)current-source converters(CSCs)fed electric machine systems can be considered as a type of high reliability energy conversion systems,since they work with the long-life DC-link inductor and offer high fault-tolerant capability for short-circuit faults.Besides,they provide motor friendly waveforms and four-quadrant operation ability.Therefore,they are suitable for high-power applications of fans,pumps,compressors and wind power generation.The purpose of this paper is to comprehensively review recent developments of key technologies on modulation and control of high-power(HP)PWM-CSC fed electric machines systems,including reduction of low-order current harmonics,suppression of inductor–capacitor(LC)resonance,mitigation of common-mode voltage(CMV)and control of modular PWM-CSC fed systems.In particular,recent work on the overlapping effects during commutation,LC resonance suppression under fault-tolerant operation and collaboration of modular PMW-CSCs are described.Both theoretical analysis and some results in simulations and experiments are presented.Finally,a brief discussion regarding the future trend of the HP CSC fed electric machines systems is presented.

Sparse current source reconstruction in MCG

Cardiac current source reconstruction is investigated by a fast greedy sparse(FGS) method applied to simulated and real magnetocardiography(MCG) data measured using 61-channel superconducting quantum interference device. The approach reduces the size of the lead field matrix based on a priori knowledge of dipolar magnetic field map. Consequently, the computational demands and the accuracy of sparse source reconstruction are improved simultaneously. The simulation results demonstrate that the FGS method is capable of reconstructing sparse equivalent current sources using the magnetic field data generated by a single current source with varying orientation or multiple current sources generated randomly. In addition, we analyze the cardiac current source reconstructed with real MCG data at typical instants and discuss the electrical excitation conduction during the QRS complex based on moving sparse source imaging.

A uniform phase noise QVCO with a feedback current source

A novel integrated quadrature voltage controlled oscillator （QVCO） with a feedback current source is presented in this paper. Benefiting from the current adjusting function of the feedback current source, the proposed QVCO exhibits a uniform phase noise over the entire tuning range. This QVCO is implemented in 65-nm CMOS technology. The measurement results show that it draws less than 3-mA average current from a 1.2-V supply and the phase noise is less than -110 dBc/Hz @IMHz offset over the entire tuning range. The fluctuation of phase noise @IMHz offset from the center frequency of 2.84-GHz to 3.27-GHz is less than 1 dBc/Hz, which validates the correctness of the proposed current source feedback technique.

Generalized multilevel current source inverter topology with self-balancing current

A generalized single-phase multilevel current source inverter (MCSI) topology with self-balancing current is proposed, which uses the duality transformation from the generalized multilevel voltage source inverter (MVSI) topology. The existing single-phase 8-and 6-switch 5-level current source inverters (CSIs) can be derived from this generalized MCSI topology. In the proposed topology, each intermediate DC-link current level can be balanced automatically without adding any external circuits; thus, a true multilevel structure is provided. Moreover, owing to the dual relationship, many research results relating to the op- eration, modulation, and control strategies of MVSIs can be applied directly to the MCSIs. Some simulation results are presented to verify the proposed MCSI topology.

Online Learning Control for Harmonics Reduction Based on Current Controlled Voltage Source Power Inverters

Nonlinear loads in the power distribution system cause non-sinusoidal currents and voltages with harmonic components.Shunt active filters(SAF) with current controlled voltage source inverters(CCVSI) are usually used to obtain balanced and sinusoidal source currents by injecting compensation currents.However,CCVSI with traditional controllers have a limited transient and steady state performance.In this paper,we propose an adaptive dynamic programming(ADP) controller with online learning capability to improve transient response and harmonics.The proposed controller works alongside existing proportional integral(PI) controllers to efficiently track the reference currents in the d-q domain.It can generate adaptive control actions to compensate the PI controller.The proposed system was simulated under different nonlinear(three-phase full wave rectifier) load conditions.The performance of the proposed approach was compared with the traditional approach.We have also included the simulation results without connecting the traditional PI control based power inverter for reference comparison.The online learning based ADP controller not only reduced average total harmonic distortion by 18.41%,but also outperformed traditional PI controllers during transients.

Magnetite Quartzite-Type Iron Ores – China's Most Important Current Iron Ore Source

China is abundant in iron-ore resources, with proven ore reserves of 576.62×10^8 t and proven reserves of 210×10^8 t, containing an average iron content of 33%. However, the rich iron-ore reserves of 10.85×10^8 t only account for 1.9% of all proven reserves. China＇s iron-ore resources are characterized by many lean ores and a few rich ones.

Kuroshio warm filament and the source of the warm water of the Tsushima Current

Characteristics and evolution of the Kuroshio frontal eddies and warm filaments are analyzed according to two series of satellite images (March 5 to 7, 1986 and April 14 to 16, 1988). The results show that the frontal eddies in the East China Sea are generated at the shelf break and move along the continental slope at a speed of 15 cm/s with the Kuroshio. The frontal eddies occur about every 10 d and evolve to be warm filaments a few hundred km in length and 30-40 km in width in the area west of the Yaku-shima. Meanwhile, the existence of the warm filament was also found in the area by analysing the hydrographic data in the area west of Kyushu during May 24-June 5, 1988.The Kuroshio warm filaments move westward opposite to the Kuroshio and then turn northward at the shelf break and become the main source of the warm water of the Tsushima Warm Current. A simple dynamic explanation for the process is presented in this paper.

Improved power simulation of AlGaN/GaN HEMT at class-AB operation via an RF drain–source current correction method

A new modified Angelov current–voltage characteristic model equation is proposed to improve the drain–source current（Ids） simulation of an Al Ga N/Ga N-based（gallium nitride） high electron mobility transistor（Al Ga N/Ga N-based HEMT） at high power operation. Since an accurate radio frequency（RF） current simulation is critical for a correct power simulation of the device, in this paper we propose a method of Al Ga N/Ga N high electron mobility transistor（HEMT）nonlinear large-signal model extraction with a supplemental modeling of RF drain–source current as a function of RF input power. The improved results of simulated output power, gain, and power added efficiency（PAE） at class-AB quiescent bias of Vgs =-3.5 V, Vds= 30 V with a frequency of 9.6 GHz are presented.

Development of data acquisition and over-current protection systems for a suppressor-grid current with a neutral-beam ion source

Neutral beam injection is one of the effective auxiliary heating methods in magnetic-confinementfusion experiments. In order to acquire the suppressor-grid current signal and avoid the grid being damaged by overheating, a data acquisition and over-current protection system based on the PXI（PCI e Xtensions for Instrumentation） platform has been developed. The system consists of a current sensor, data acquisition module and over-current protection module. In the data acquisition module,the acquired data of one shot will be transferred in isolation and saved in a data-storage server in a txt file. It can also be recalled using NBWave for future analysis. The over-current protection module contains two modes： remote and local. This gives it the function of setting a threshold voltage remotely and locally, and the forbidden time of over-current protection also can be set by a host PC in remote mode. Experimental results demonstrate that the data acquisition and overcurrent protection system has the advantages of setting forbidden time and isolation transmission.

A study on the source of the Tsushima Warm Current water

On the basis of the hydrographic data in the area west of Kyushu from four cruises of R/V Xiangyanghong No. 9 from 1987 to 1988 , the circulation features in the investigation area are described and the source of the Tsushima Warm Current water (TWCW) is explored by using the observed and geostrophic current results and tracking the Kuroshio Subsurface High Salinity Core (KSHSC).