This paper describes the application of orthogonal test design coupled with non-linear regression analysis to optimize abrasive suspension jet (AS J) cutting process and construct its cutting model. Orthogonal test ...This paper describes the application of orthogonal test design coupled with non-linear regression analysis to optimize abrasive suspension jet (AS J) cutting process and construct its cutting model. Orthogonal test design is applied to cutting stainless steel. Through range analysis on experiment results, the optimal process conditions for the cutting depth and the kerr ratio of the bottom width to the top width can be determined. In addition, the analysis of ranges and variances are all employed to identify various factors: traverse rate, working pressure, nozzle diameter, standoff distance which denote the importance order of the cutting parameters affecting cutting depth and the kerf ratio of the bottom width to the top width. ~rthermore, non-linear regression analysis is used to establish the mathematical models of the cutting parameters based on the cutting depth and the kerr ratio. Finally, the verification experiments of cutting parameters' effect on cutting performance, which show that optimized cutting parameters and cutting model can significantly improve the prediction of the cutting ability and quality of ASJ.展开更多
This study deals with Nd:YAG laser cutting nonmetallic materials, which is one of the most important and popular industrial applications of laser. The main theme is to evaluate the effects of Nd:YAG laser beam power...This study deals with Nd:YAG laser cutting nonmetallic materials, which is one of the most important and popular industrial applications of laser. The main theme is to evaluate the effects of Nd:YAG laser beam power besides work piece scanning speed. For approximate cutting depth, a theoretical study is conducted in terms of material property and cutting speed. Results show a nonlinear relation between the cutting depth and input energy. There is no significant effect of speed on cutting depth with the speed being larger than 30 mm/s. An extra energy is utilized in the deep cutting. It is inferred that as the laser power increases, cutting depth increases. The experimental outcomes are in good agreement with theoretical results. This analysis will provide a guideline for laser-based industry to select a suitable laser for cutting, scribing, trimming, engraving, and marking nonmetallic materials.展开更多
This paper begins with a consideration of the influence of feed per revolution upon the depth of a cut and the impact of the machining method on the direction of tool pressure average and subsequent description of eff...This paper begins with a consideration of the influence of feed per revolution upon the depth of a cut and the impact of the machining method on the direction of tool pressure average and subsequent description of efficient cutting directions and the methods for load cell orientation. The paper goes further into the key conclusions concerning the dependences of the cutting depth at high-speed milling as in the case of discontinuous functions. It ends with recommendations offered for positioning of load cells for cut-up milling and cut-down milling.展开更多
In precision machining processes such as grinding,for example,analysis of machined surface is important one of most parameters to evaluate process performance.Equally important is to perform tribological analysis to u...In precision machining processes such as grinding,for example,analysis of machined surface is important one of most parameters to evaluate process performance.Equally important is to perform tribological analysis to understand chip formation and abrasive wheel wear,thus enabling manufacturing of components free of thermal damages.In grinding,due to high hardness of abrasive grains that remove material from workpiece in chip form and very low values of radial depth of cut,combination of low roughness values and tight dimensional tolerances is attained.Accordingly,the parameters involved in this process are determinant in surface quality that is primarily evaluated in terms of surface roughness and workpiece functionality.In this work,surface roughness(Rt parameter)and scanning electron microscope(SEM)images of ground surfaces of the AISI 420 martensitic stainless steel samples were evaluated.Tests were carried out in surface grinding with a white aluminum oxide wheel and an environmentally-friendly semisynthetic water-soluble coolant.Two values of radial depth of cut(10μm and 25μm)were tested.The results showed that the highest roughness values,deeper grooves on the machined surfaces as well as poorer surface quality were obtained after grinding under the severest cutting conditions.展开更多
Metal framework composites have higher mechanical properties in examination to metals over an extensive variety of working conditions. This makes them an alluring alternative in swapping metals for different building ...Metal framework composites have higher mechanical properties in examination to metals over an extensive variety of working conditions. This makes them an alluring alternative in swapping metals for different building applications. The present review is a study on the influence of composite titanium on the cutting parameters, mechanical behavior, reinforcements, structure and nanostructure. This review will provide an understanding into selecting the optimum machining parameters for machining titanium composites. It’s also an attempt to give brief explanation by suitably machining the titanium composite which can be made reasonable.展开更多
A deduced cutting force prediction model for circular end milling process is presented in this paper. Traditional researches on cutting force model usually focus on linear milling process which does not meet other cut...A deduced cutting force prediction model for circular end milling process is presented in this paper. Traditional researches on cutting force model usually focus on linear milling process which does not meet other cutting conditions, especially for circular milling process. This paper presents an improved cutting force model for circular end milling process based on the typical linear milling force model. The curvature effects of tool path on chip thickness as well as entry and exit angles are analyzed, and the cutting force model of linear milling process is then corrected to fit circular end milling processes. Instantaneous cutting forces during circular end milling process are predicted according to the proposed model. The deduced cutting force model can be used for both linear and circular end milling processes. Finally, circular end milling experiments with constant and variable radial depth were carried out to verify the availability of the proposed method. Experiment results show that measured results and simulated results corresponds well with each other.展开更多
In this study,surface modification of monocrystalline silicon with two doses of hydrogen ion implantation and the plunge cutting process were conducted to explore the influence of hydrogen ions on the cutting behavior...In this study,surface modification of monocrystalline silicon with two doses of hydrogen ion implantation and the plunge cutting process were conducted to explore the influence of hydrogen ions on the cutting behavior of silicon.The results show that ion implantation is capable of deteriorating or improving the machinability of silicon,depending on the implantation dose.More cleavages and a reduction of critical depth of cut(CDoC)were observed for the silicon with a low implantation dose in the cutting direction of<100>in comparison to bare silicon,while no cleavage and an increase of CDoC were achieved after implantation with a high dose in the same cutting direction.Besides,the ductile cutting and thrust forces of the silicon with the low dose are larger than the bare silicon,but the forces are significantly reduced for the silicon after the high dose of implantation.The variation of the cutting forces is due to the different required stresses to overcome ductile and fracture deformation of silicon.展开更多
基金supported by the Science and Technology Development Foundation of Shanghai Municipal Science and Technology Commission (Grant No.037252022)
文摘This paper describes the application of orthogonal test design coupled with non-linear regression analysis to optimize abrasive suspension jet (AS J) cutting process and construct its cutting model. Orthogonal test design is applied to cutting stainless steel. Through range analysis on experiment results, the optimal process conditions for the cutting depth and the kerr ratio of the bottom width to the top width can be determined. In addition, the analysis of ranges and variances are all employed to identify various factors: traverse rate, working pressure, nozzle diameter, standoff distance which denote the importance order of the cutting parameters affecting cutting depth and the kerf ratio of the bottom width to the top width. ~rthermore, non-linear regression analysis is used to establish the mathematical models of the cutting parameters based on the cutting depth and the kerr ratio. Finally, the verification experiments of cutting parameters' effect on cutting performance, which show that optimized cutting parameters and cutting model can significantly improve the prediction of the cutting ability and quality of ASJ.
基金supported by the Science Foundation of the Ministry of Science and Technology Malaysiathe Islamic Development Bank Jeddahsupport of the Universiti Teknologi Malaysia for this research work
文摘This study deals with Nd:YAG laser cutting nonmetallic materials, which is one of the most important and popular industrial applications of laser. The main theme is to evaluate the effects of Nd:YAG laser beam power besides work piece scanning speed. For approximate cutting depth, a theoretical study is conducted in terms of material property and cutting speed. Results show a nonlinear relation between the cutting depth and input energy. There is no significant effect of speed on cutting depth with the speed being larger than 30 mm/s. An extra energy is utilized in the deep cutting. It is inferred that as the laser power increases, cutting depth increases. The experimental outcomes are in good agreement with theoretical results. This analysis will provide a guideline for laser-based industry to select a suitable laser for cutting, scribing, trimming, engraving, and marking nonmetallic materials.
文摘This paper begins with a consideration of the influence of feed per revolution upon the depth of a cut and the impact of the machining method on the direction of tool pressure average and subsequent description of efficient cutting directions and the methods for load cell orientation. The paper goes further into the key conclusions concerning the dependences of the cutting depth at high-speed milling as in the case of discontinuous functions. It ends with recommendations offered for positioning of load cells for cut-up milling and cut-down milling.
文摘In precision machining processes such as grinding,for example,analysis of machined surface is important one of most parameters to evaluate process performance.Equally important is to perform tribological analysis to understand chip formation and abrasive wheel wear,thus enabling manufacturing of components free of thermal damages.In grinding,due to high hardness of abrasive grains that remove material from workpiece in chip form and very low values of radial depth of cut,combination of low roughness values and tight dimensional tolerances is attained.Accordingly,the parameters involved in this process are determinant in surface quality that is primarily evaluated in terms of surface roughness and workpiece functionality.In this work,surface roughness(Rt parameter)and scanning electron microscope(SEM)images of ground surfaces of the AISI 420 martensitic stainless steel samples were evaluated.Tests were carried out in surface grinding with a white aluminum oxide wheel and an environmentally-friendly semisynthetic water-soluble coolant.Two values of radial depth of cut(10μm and 25μm)were tested.The results showed that the highest roughness values,deeper grooves on the machined surfaces as well as poorer surface quality were obtained after grinding under the severest cutting conditions.
文摘Metal framework composites have higher mechanical properties in examination to metals over an extensive variety of working conditions. This makes them an alluring alternative in swapping metals for different building applications. The present review is a study on the influence of composite titanium on the cutting parameters, mechanical behavior, reinforcements, structure and nanostructure. This review will provide an understanding into selecting the optimum machining parameters for machining titanium composites. It’s also an attempt to give brief explanation by suitably machining the titanium composite which can be made reasonable.
基金co-supported by Open National Natural Science Foundation of China(No.51005183)National Science and Technology Major Project(No.2011ZX04016031)China Postdoctoral Science Foundation(No.2012M521804)
文摘A deduced cutting force prediction model for circular end milling process is presented in this paper. Traditional researches on cutting force model usually focus on linear milling process which does not meet other cutting conditions, especially for circular milling process. This paper presents an improved cutting force model for circular end milling process based on the typical linear milling force model. The curvature effects of tool path on chip thickness as well as entry and exit angles are analyzed, and the cutting force model of linear milling process is then corrected to fit circular end milling processes. Instantaneous cutting forces during circular end milling process are predicted according to the proposed model. The deduced cutting force model can be used for both linear and circular end milling processes. Finally, circular end milling experiments with constant and variable radial depth were carried out to verify the availability of the proposed method. Experiment results show that measured results and simulated results corresponds well with each other.
基金The work described in this paper was jointly supported by the Research Committee(Project No.G-YBLE)State Key Laboratory of Ultra-precision Machining Technology(Project No.RUWB)of the Hong Kong Polytechnic University.
文摘In this study,surface modification of monocrystalline silicon with two doses of hydrogen ion implantation and the plunge cutting process were conducted to explore the influence of hydrogen ions on the cutting behavior of silicon.The results show that ion implantation is capable of deteriorating or improving the machinability of silicon,depending on the implantation dose.More cleavages and a reduction of critical depth of cut(CDoC)were observed for the silicon with a low implantation dose in the cutting direction of<100>in comparison to bare silicon,while no cleavage and an increase of CDoC were achieved after implantation with a high dose in the same cutting direction.Besides,the ductile cutting and thrust forces of the silicon with the low dose are larger than the bare silicon,but the forces are significantly reduced for the silicon after the high dose of implantation.The variation of the cutting forces is due to the different required stresses to overcome ductile and fracture deformation of silicon.