Ecological environment analysis of Abies holophylla plantations under different cutting systems

Different types of plantations were observed in Baishilazi National Nature Reserve, Liaoning Province, for 34 a. The environmental quality ofAbies holophylla plantations was analyzed under different cutting systems. Analysis factors included soil erosion rate, humification degree of litters, and water hold capacity. The surface soil loss of clear cutting area was 19000t·km?2·a?1 more than that of selective cutting area. The content of soil organic matter in board-leaved—Abies holophylla forest was 4.62% more than that in pure stand, and the water hold capacity of the mixed forest was 1.43 time of that of pure stand. The mixed forest of board-leaved—Abies holophylla by selective cutting can upgrade the ecological environment quality.

Research on the Mechanism of Abrasive Particles Accelerated and a Cutting System of a Premixed Abrasive Jet

Forces acting on abrasive in the process of speeding up have been analyzed. Motion differential equation of abrasive in a pipeline and nozzle has been given, respectively. Mechanisms of abrasive particles accelerated in a premixed abrasive jet has been analyzed. The study shows that driven by high-pressure water, velocity of an abrasive is near to velocity of water in pipeline through the acceleration distance. In the taper section of a nozzle, water and abrasive particles are greatly accelerated at the same time. But velocity of an abrasive always lags behind velocity of water. A premixed abrasive jet cutting system has been introduced. The structure and working principles of the system have been given. The system is an assembly of abrasive screening and filling. By use of the premixed abrasive jet cutting system established, cutting experiments have been made to test the main parameters which influence the cutting performances such as working pressure, standoff and traverse velocity, and the nozzle diameter affecting cutting chink width.

Reasonable location parameters of pick and nozzle in combined cutting system

The drum shearer and high pressure water jet combined cutting system is an effective technology to cut hard coal-rock, but one problem of the technology is the choice of pick and nozzle location parameters. In order to solve the problem, the process and mechanism of combined cutting arc studied and mining seepage catastrophe theory is used to construct the mathematic and physical model of combined cutting hard coal-rock. Based on the model and detailed analysis of combined cutting mechanism, the single pick and nozzle combined cutting test-bed is built to test the main pick and nozzle location parameters of drum shearer and water jet combined cutting system. Test results show that the best vertical distance between the pick-tip and nozzle center point is the sum of cutting thickness and proper target distance in the Y axial direction; the best horizontal distance is the length between pick-tip point and coal-rock surface bursting crack point in the X axial direction. The best incident angle of water jet should be the same as the bursting crack line＇s angle in theory, but considering other important factors comprehensively, it is more reasonable when the incident angle of water jet is 90°.

Diameter distribution of trees in natural stands managed on polycyclic cutting system

Diameter frequency distribution in a specific stand provides basic information for forest resources management. In this study, four probability models were applied to analyze diameter distribution of natural forests after selective cutting with different intensities （low intensity of 13.0% in volume, medium intensity of 29.1%, high intensity of 45.8%, and extra-high intensity of 67.1%） The results show that the skewness and kurtosis of the four models are positive except that of low intensity selective cutting, which suggest that the number of small-size trees dominate the stand. The more intensity of selective cutting, the wider range of diameter distributions. The diameter structure of selective cutting with low intensity met Weibull and Beta distributions; that of medium intensity met Weibull, negative exponential as well as Gamma distributions; that of high intensity cutting met Weibull and negative exponential distributions, but that of extra-high intensity could not meet any above model. Weibull distribution model fits better than others regarding the structure of diameter distribution in natural forests managed on polycyclic cutting system. The results will provide basic information for sustainable management for mixed natural stands managed on a polycyclic cutting system.

Design and Numerical Simulation of Dust Removal System for Sutomotive Iongitudinal Beam Plasma Cutting

To improve the poor efficiency of the dust removal system in the plasma cutting station of automotive longitudinal beams,and reduce the cutting surface quality degradation due to dust,a bottom-side suction dust removal system is designed,and the dust removal effect is optimized through the setting of the following dampers and diversion plates.The result of numerical simulation indicates that the particle collection rate can reach 99.44%,and the field test also proves the effectiveness of the dust removal system,which is of guiding significance for the transformation of other similar dust removal systems.

Instability mechanism of mining roadway passing through fault at different angles in kilometre-deep mine and control measures of roof cutting and NPR cables

The angle α between the fault strike and the axial direction of the roadway produces different damage characteristics. In this paper, the research methodology includes theoretical analyses, numerical simulations and field experiments in the context of the Daqiang coal mine located in Shenyang, China. The stability control countermeasure of "pre-splitting cutting roof + NPR anchor cable"(PSCR-NPR) is simultaneously proposed. According to the different deformation characteristics of the roadway, the faults are innovatively classified into three types, with α of type I being 0°-30°, α of type II being 30°-60°, and α of type III being 60°-90°. The full-cycle stress evolution paths during mining roadway traverses across different types of faults are investigated by numerical simulation. Different pinch angles α lead to high stress concentration areas at different locations in the surrounding rock. The non-uniform stress field formed in the shallow surrounding rock is an important reason for the instability of the roadway. The pre-cracked cut top shifted the high stress region to the deep rock mass and formed a low stress region in the shallow rock mass. The high prestressing NPR anchor cable transforms the non-uniform stress field of the shallow surrounding rock into a uniform stress field. PSCR-NPR is applied in the fault-through roadway of Daqiang mine. The low stress area of the surrounding rock was enlarged by 3-7 times, and the cumulative convergence was reduced by 45%-50%. It provides a reference for the stability control of the deep fault-through mining roadway.

Unraveling engineering disturbance effects on deformation in red-bed mudstone railway cuttings:incorporating crack-facilitated moisture diffusion

Red-bed mudstone, prevalent in southwest China, poses a formidable challenge due to its hydrophilic clay minerals, resulting in expansion, deformation, and cracking upon exposure to moisture. This study addresses uplift deformation disasters in high-speed railways by employing a moisture diffusion-deformation-fracture coupling model based on the finite-discrete element method(FDEM). The model integrates the influence of cracks on moisture diffusion. The investigation into various excavation depths reveals a direct correlation between depth and the formation of tensile cracks at the bottom of the railway cutting. These cracks expedite moisture migration, significantly impacting the temporal and spatial evolution of the moisture field. Additionally, crack expansion dominates hygroscopic deformation, with the lateral coordinate of the crack zone determining peak vertical displacement. Furthermore, key factors influencing deformation in railway cuttings, including the swelling factor and initial moisture content at the bottom of the cutting, are explored. The number of tensile and shear cracks increases with greater excavation depth, particularly concerning shear cracks. Higher swelling factors and initial moisture contents result in an increased total number of cracks, predominantly shear cracks. Numerical calculations provide valuable insights, offering a scientific foundation and directional guidance for the precise prevention, control, prediction, and comprehensive treatment of mudstone-related issues in high-speed railways.

Assessing cutter-rock interaction during TBM tunnelling in granite:Large-scale standing rotary cutting tests and 3D DEM simulations

The widespread utilisation of tunnel boring machines(TBMs)in underground construction engineering requires a detailed investigation of the cutter-rock interaction.In this paper,we conduct a series of largescale standing rotary cutting tests on granite in conjunction with high-fidelity numerical simulations based on a particle-type discrete element method(DEM)to explore the effects of key cutting parameters on the TBM cutter performance and the distribution of cutter-rock contact stresses.The assessment results of cutter performance obtained from the cutting tests and numerical simulations reveal similar dependencies on the key cutting parameters.More specifically,the normal and rolling forces exhibit a positive correlation with penetration but are slightly influenced by the cutting radius.In contrast,the side force decreases as the cutting radius increases.Additionally,the side force shows a positive relationship with the penetration for smaller cutting radii but tends to become negative as the cutting radius increases.The cutter's relative effectiveness in rock breaking is significantly impacted by the penetration but shows little dependency on the cutting radius.Consequently,an optimal penetration is identified,leading to a low boreability index and specific energy.A combined Hertz-Weibull function is developed to fit the cutter-rock contact stress distribution obtained in DEM simulations,whereby an improved CSM(Colorado School of Mines)model is proposed by replacing the original monotonic cutting force distribution with this combined Hertz-Weibull model.The proposed model outperforms the original CSM model as demonstrated by a comparison of the estimated cutting forces with those from the tests/simulations.The findings from this work that advance our understanding of TBM cutter performance have important implications for improving the efficiency and reliability of TBM tunnelling in granite.

Precipitates Generation Mechanism and Surface Quality Improvement for Aluminum Alloy 6061 in Diamond Cutting

To improve the surface quality for aluminum alloy 6061(Al6061) in ultra-precision machining, we investigated the factors affecting the surface finish in single point diamond turning(SPDT)by studying influence of the precipitates generation of Al6061 on surface integrity and surface roughness.Based on the Johnson-Mehl-Avrami solid phase transformation kinetics equation, theoretical and experimental studies were conducted to build the relationship between the aging condition and the type, size and number of the precipitates for Al6061. Diamond cutting experiments were conducted to machine Al6061 samples under different aging conditions. The experimental results show that, the protruding on the chip surface is mainly Mg_(2)Si and the scratches on the machined surface mostly come from the iron-containing phase(α-, β-AlFeSi).Moreover, the generated Mg_(2)Si and α-, β-AlFeSi affect the surface integrity and the diamond turned surface roughness. Especially, the achieved surface roughness in SPDT is consistent with the variation of the number of AlFeSi and Mg_(2)Si with the medium size(more than 1 μm and less than 2 μm) in Al6061.

Hole cleaning evaluation and installation spacing optimization of cuttings bed remover in extended-reach drilling

In extended-reach or long-horizontal drilling,cuttings usually deposit at the bottom of the annulus.Once cuttings accumulate to a certain thickness,complex problems such as excessive torque and drag,tubing buckling,and pipe stuck probably occur,which results in a lot of non-productive time and remedial operations.Cuttings bed remover can efficiently destroy deposited cuttings in time through hydraulic and mechanical stirring effects.This paper aims to build a method for hole cleaning evaluation and installation spacing optimization of cuttings bed remover to improve the wellbore cleaning effect.Firstly,a Computational Fluid Dynamics approach with Eulerian—Eulerian multiphase model was utilized to investigate the mechanism of cuttings transportation,and a new type of cuttings bed remover was designed.Next,an evaluation method of hole cleaning effect of remover was established.After that,the effects of several drilling parameters on hole cleaning including flow rate of drilling fluid,rotational speed of drillpipe,rate of penetration,wellbore size,rheological property of drilling fluid,and remover eccentricity on the performance of cuttings bed remover were investigated.The results demonstrate that the new type of remover with streamline blade performs better than conventional removers.The efficiency of hole cleaning is greatly improved by increasing the rotational speed of drillpipe,flow rate of drilling fluid,remover eccentricity,and 6 rpm Fann dial reading for drilling fluid.While higher rate of penetration and large wellbore size result in worse hole cleaning.These findings can serve as an important guide for the structure optimization design of cuttings bed remover and installation spacing of removers.

Ground response and failure mechanism of gob-side entry by roof cutting with hard main roof

This study is the result of long-term efforts of the authors’team to assess ground response of gob-side entry by roof cutting(GSERC)with hard main roof,aiming at scientific control for GSERC deformation.A comprehensive field measurement program was conducted to determine entry deformation,roof fracture zone,and anchor bolt(cable)loading.The results indicate that GSERC deformation presents asymmetric characteristics.The maximum convergence near roof cutting side is 458 mm during the primary use process and 1120 mm during the secondary reuse process.The entry deformation is closely associated with the primary development stage,primary use stage,and secondary reuse stage.The key block movement of roof cutting structure,a complex stress environment,and a mismatch in the supporting design scheme are the failure mechanism of GSERC.A controlling ideology for mining states,including regional and stage divisions,was proposed.Both dynamic and permanent support schemes have been implemented in the field.Engineering practice results indicate that the new support scheme can efficiently ensure long-term entry safety and could be a reliable approach for other engineering practices.

Endoscopic radial incision and cutting method for adult congenital duodenal webs:A case report

BACKGROUND Congenital duodenal webs are rare in adults and can lead to various symptoms such as nausea,vomiting,and postprandial fullness.The treatment for this disease is mostly surgical.Endoscopic treatment techniques have been developed and attempted for this disease.Endoscopic radial incision and cutting(RIC)techniques are reportedly very effective in benign anastomotic stricture.This case report highlights the effectiveness and safety of endoscopic RIC as a minimally invasive treatment for adult congenital duodenal webs.CASE SUMMARY A 23-year-old female patient with indigestion was referred to a tertiary hospital.The patient complained of postprandial fullness in the epigastric region.Previous physical examinations or blood tests indicated no abnormalities.Computed tomography revealed an eccentric broad-based delayed-enhancing mass-like lesion in the second portion of the duodenum.Endoscopy showed an enlarged gastric cavity and a significantly dilated duodenal bulb;a very small hole was observed in the distal part of the second portion,and scope passage was not possible.Gastrografin upper gastrointestinal series was performed,revealing an intraduodenal barium contrast-filled sac with a curvilinear narrow radiolucent rim,a typical"windsock"sign.Endoscopic RIC was performed on the duodenal web.The patient recovered uneventfully.Follow-up endoscopy showed a patent duodenal lumen without any residual stenosis.The patient reported complete resolution of symptoms at the 18-month follow-up.CONCLUSION Endoscopic RIC may be an effective treatment for congenital duodenal webs in adults.

Cutting Propagation Technique of Pennisetum purpureum Schum

[Objectives]The paper was to study the cutting propagation technique of Pennisetum purpureum Schum and to provide a technical reference for establishing an efficient cutting propagation method.[Methods]Six treatments were set up using P.purpureum cv.Guiminyin and P.purpureum cv.Guimu-1 as test materials,including 1-node oblique insertion,1-node oblique insertion+rooting powder,1-node transverse burial,2-node oblique insertion,2-node oblique insertion+rooting powder and 2-node transverse burial.The following indices were observed and determined for P.purpureum cuttings:emergence rate,rooting rate,root number,longest root length,fresh root weight,plant height,number of tillers,number of leaves,and fresh stem and leaf weight.[Results]In the 2-node cutting+rooting powder treatment,Guiminyin and Guimu-1 exhibited the highest survival rate,root growth indices,and stem and leaf growth indices,with the emergence rates of 94.29%and 90.26%,respectively.The 2-node cutting treatment followed closely behind,while the 1-node cutting treatment had the lowest indices.Under the same treatment,Guimuyin exhibited higher mean values for plant height,number of leaves,fresh stem and leaf weight,longest root length,and fresh root weight compared to Guimu-1.However,it had lower mean number of tillers,and emergence rate and rooting rate of the 1-node cutting treatment compared to Guimu-1.[Conclusions]The P.purpureum cuttings thrived in the 2-node cutting+rooting powder treatment,and the overall cutting effect of Guiminyin was superior to that of Guimu-1.

Application of Fuyang Paper Cutting Art in Cultural and Creative Design from the Perspective of Rural Revitalization

The application significance of Fuyang paper cutting art in cultural and creative design from the perspective of rural revitalization was discussed,and the implementation principles and specific practices of applying the elements and techniques of Fuyang traditional paper cutting art in cultural and creative products with local features were analyzed to provide reference for rural revitalization and development of cultural industry.

Cutting-edge Technological Innovation Outcome Displayed at 2024 Beijing Science and Technology Week

The 2024 National Science and Technology Week and Beijing Science and Technology Week opened in Shougang Park in Shijingshan District from May 25 to June 1.Under the theme of“Carrying forward the spirit of scientists and inspiring societal innovation,”this event focused on the new-generation IT technology,medical health,energy and technology,modern agriculture and intelligent manufacturing industries.

Research on the Resistance of Cutting Mechanism of Mining Longitudinal Roadheader

In order to accurately obtain the dynamic characteristics of the cutting mechanism of the mining longitudinal roadheader,combined with the working principle of the mining longitudinal roadheader,the theoretical analysis and derivation are carried out in detail.By using ADAMS to simulate,the resistance curve and torque curve of the cutting mechanism in different directions are obtained.The results show that ADAMS can effectively predict the excavation resistance and torque of the cutting mechanism of mining longitudinal roadheader,which has certain reference value for future optimization design.

Multi-Sensor Intelligent System for On-Line and Real-Time Moneitoring Tool Cutting State in FMS

The principle and the constitution of an intelligent system for on-line and real-time montitoring tool cutting state were discussed and a synthetic sensors schedule combined a new type fluid acoustic emission sensor (AE) with motor current sensor was presented. The parallel communication between control system of machine tools, the monitoring intelligent system,and several decision-making systems for identifying tool cutting state was established It can auto - matically select the sensor way ,monitoring mode and identifying method in machining process- ing so as to build a successful and effective intelligent system for on -line and real-time moni- toring cutting tool states in FMS.

Effects of servo system on limited cutting width in CNC heavy cutting

A mathematical model of the computer numerical control (CNC) heavy cuttingservo system including chatter in cutting courses was constructed for the chatter in CNC heavycutting. The theoretical analysis, computer simulation and orthogonal tests on this model show thatincreasing the gain of position K_(pp) can improve the rapid tracking performance of machine tools,and decreasing the delay time of speed loop τ_s can quickly eliminate the static error in thesystem, but the limited cutting width b_(lim) will descend correspondingly; excessively large orexcessively small gain of speed loop K_(ps) can result in decreasing b_(lim); optimizing K_(pp),τ_s and K_(ps) can improve the dynamic and static performance of the system and increase b_(lim).It is easy and feasible to optimize the servo parameters by the orthogonal test. This method caneffectively improve the system's stability and limited cutting width and it is suitable for the CNCheavy cutting of heavy-duty machine tools.

Adaptive fuzzy integral sliding mode velocity control for the cutting system of a trench cutter

This paper presents a velocity controller for the cutting system of a trench cutter(TC). The cutting velocity of a cutting system is affected by the unknown load characteristics of rock and soil. In addition, geological conditions vary with time. Due to the complex load characteristics of rock and soil, the cutting load torque of a cutter is related to the geological conditions and the feeding velocity of the cutter. Moreover, a cutter's dynamic model is subjected to uncertainties with unknown effects on its function. In this study, to deal with the particular characteristics of a cutting system, a novel adaptive fuzzy integral sliding mode control(AFISMC) is designed for controlling cutting velocity. The model combines the robust characteristics of an integral sliding mode controller with the adaptive adjusting characteristics of an adaptive fuzzy controller. The AFISMC cutting velocity controller is synthesized using the backstepping technique. The stability of the whole system including the fuzzy inference system, integral sliding mode controller, and the cutting system is proven using the Lyapunov theory. Experiments have been conducted on a TC test bench with the AFISMC under different operating conditions. The experimental results demonstrate that the proposed AFISMC cutting velocity controller gives a superior and robust velocity tracking performance.

Effect of shelterwood cutting method on forest regeneration and stand structure in a Hyrcanian forest ecosystem

A study was carried out to evaluate the effect of shelterwood cutting methods on stand structure and regeneration density. Data were collected from a northern hardwood forest stands in Iran with Fagus orientalis Lipsky as dominant species, with/without shelterwood cutting operation. Results clearly demonstrate that the management of Fagus orientalis Lipsky with shelterwood cutting system affected the frequency and diversity of the understory herbaceous species. The frequency of Viola silvestris Lam., Asperula odorata L., Carex spp. and Rubus hyr-canus Juz increased significantly after shelterwood cutting. The DBH （diameter at breast height） of commercial species in control stands （57.50±2.15 cm） was greater than that in treated stands （50.67±1.88 cm）, whereas the total height of trees was similar between treated and control plots （21±0.5 m）. The number of Parrotia persica seedlings increased by 13.2% from 1995 to 2005 whereas the number of Fagus orientalis and Carpinus betulus seedlings significantly decreased from 1995 to 2005. In conclusion, it confirms that instead of shelterwood cutting method other silvicultural practices such as selection cutting method should be applied for the mountainous beech stands of Hyrcanian forests.