Lower surface roughness and sharper cutting edge are beneficial for improving the machining quality of the cut?ting tool, while coatings often deteriorate them. Focusing on the diamond coated WC?Co milling cutter, the...Lower surface roughness and sharper cutting edge are beneficial for improving the machining quality of the cut?ting tool, while coatings often deteriorate them. Focusing on the diamond coated WC?Co milling cutter, the abrasive flow machining(AFM) is selected for reducing the surface roughness and sharpening the cutting edge. Comparative cutting tests are conducted on di erent types of coated cutters before and after AFM, as well as uncoated WC?Co one, demonstrating that the boron?doped microcrystalline and undoped fine?grained composite diamond coated cutter after the AFM(AFM?BDM?UFGCD) is a good choice for the finish milling of the 6063 Al alloy in the present case, because it shows favorable machining quality close to the uncoated one, but much prolonged tool lifetime. Besides, compared with the micro?sized diamond films, it is much more convenient and e cient to finish the BDM?UFGCD coated cutter covered by nano?sized diamond grains, and resharpen its cutting edge by the AFM, owing to the lower initial surface roughness and hardness. Moreover, the boron incorporation and micro?sized grains in the underly?ing layer can enhance the film?substrate adhesion, avoid the rapid film removal in the machining process, and thus maximize the tool life(1040 m, four times more than the uncoated one). In general, the AFM is firstly proposed and discussed for post?processing the diamond coated complicated cutting tools, which is proved to be feasible for improving the cutting performance展开更多
The wear forms and reasons of PCBN tools when dry-cutting bearing steel GCr15are studied systematically. The effect law of the workpiece hardness on PCBN tools is gained andtool wearing with the quickest speed at the ...The wear forms and reasons of PCBN tools when dry-cutting bearing steel GCr15are studied systematically. The effect law of the workpiece hardness on PCBN tools is gained andtool wearing with the quickest speed at the workpiece critical hardness is proved. The life equationat two kinds of workpiece hardness demonstrates that the effect of the cutting speed on the PCBNtool life is less than that of carbide tools and ceramic tools.展开更多
C-276 nickel-based alloy is a difficult-to-cut material. In high-speed machining of Hastelloy C-276, notching is a prominent failure mode due to high mechanical properties of work piece, which results in the short too...C-276 nickel-based alloy is a difficult-to-cut material. In high-speed machining of Hastelloy C-276, notching is a prominent failure mode due to high mechanical properties of work piece, which results in the short tool life and low productivity. In this paper, a newly developed Ti（C7N3）-based cermet insert manufactured by a hot-pressing method is used to machine the C-276 nickel-based alloy, and its cutting performances are studied. Based on orthogonal experiment method, the influence of cutting parameters on tool life, material removal rates and surface roughness are investigated. Experimental research results indicate that the optimal cutting condition is a cutting speed of 50 m/min, depth of cut of 0.4 mm and feed rate of 0.15 mm/r if the tool life and material removal rates are considered comprehensively. In this case, the tool life is 32 min and material removal rates are 3000 mm^3/min, which is appropriate to the rough machining. If the tool life and surface roughness are considered, the better cutting condition is a cutting speed of 75 m/min, depth of cut of 0.6 mm and feed rate of 0.1 mm/r. In this case, the surface roughness is 0.59μm. Notch wear, flank wear, chipping at the tool nose, built-up edge（BUE） and micro-cracks are found when Ti（C7N3）-based cermet insert turned Hastelloy C-276. Oxidation, adhesive, abrasive and diffusion are the wear mechanisms, which can be investigated by the observations of scanning electron microscope and energy-dispersive spectroscopy. This research will help to guide studies on the evaluation of machining parameters to further advance the productivity of nickel based alloy Hastelloy C-276 machining.展开更多
In this paper the CNC machining of St52 was modeled using an artificial neural network(ANN)in the form of a four-layer multi-layer perceptron(MLP).The cutting parameters used in the model were cutting fluid flow,feed ...In this paper the CNC machining of St52 was modeled using an artificial neural network(ANN)in the form of a four-layer multi-layer perceptron(MLP).The cutting parameters used in the model were cutting fluid flow,feed rate,spindle speed and the depth of cut and the model output was the tool life.For obtaining more accuracy and spending less time Taguchi design of experiment(DOE)has been used and correlation between the output of the ANN and the experimental results was 96%.Further optimization process has been done by use of a genetic algorithm(GA).After optimization process tool life was increased about 8%equal to 33 min and was corroborated by experimental tests.This demonstrates that the coupling of an ANN with the GA optimization technique is a valid and useful approach to use.展开更多
基金Supported by National Natural Science Foundation of China(Grant No.51275302)China Postdoctoral Science Foundation Special Funded Project(Grant No.2016T90370)China Postdoctoral Science Foundation(Grant No.2015M580327)
文摘Lower surface roughness and sharper cutting edge are beneficial for improving the machining quality of the cut?ting tool, while coatings often deteriorate them. Focusing on the diamond coated WC?Co milling cutter, the abrasive flow machining(AFM) is selected for reducing the surface roughness and sharpening the cutting edge. Comparative cutting tests are conducted on di erent types of coated cutters before and after AFM, as well as uncoated WC?Co one, demonstrating that the boron?doped microcrystalline and undoped fine?grained composite diamond coated cutter after the AFM(AFM?BDM?UFGCD) is a good choice for the finish milling of the 6063 Al alloy in the present case, because it shows favorable machining quality close to the uncoated one, but much prolonged tool lifetime. Besides, compared with the micro?sized diamond films, it is much more convenient and e cient to finish the BDM?UFGCD coated cutter covered by nano?sized diamond grains, and resharpen its cutting edge by the AFM, owing to the lower initial surface roughness and hardness. Moreover, the boron incorporation and micro?sized grains in the underly?ing layer can enhance the film?substrate adhesion, avoid the rapid film removal in the machining process, and thus maximize the tool life(1040 m, four times more than the uncoated one). In general, the AFM is firstly proposed and discussed for post?processing the diamond coated complicated cutting tools, which is proved to be feasible for improving the cutting performance
基金This project is supported by Provincial Natural Science Foundation of China(No.59975026).
文摘The wear forms and reasons of PCBN tools when dry-cutting bearing steel GCr15are studied systematically. The effect law of the workpiece hardness on PCBN tools is gained andtool wearing with the quickest speed at the workpiece critical hardness is proved. The life equationat two kinds of workpiece hardness demonstrates that the effect of the cutting speed on the PCBNtool life is less than that of carbide tools and ceramic tools.
基金Supported by Program for New Century Excellent Talents in University of China(Grant No.NCET-13-0357)Shandong Provincial Natural Science Foundation of China(Grant No.ZR2014EEM026)Tai Shan Scholar Foundation of China
文摘C-276 nickel-based alloy is a difficult-to-cut material. In high-speed machining of Hastelloy C-276, notching is a prominent failure mode due to high mechanical properties of work piece, which results in the short tool life and low productivity. In this paper, a newly developed Ti（C7N3）-based cermet insert manufactured by a hot-pressing method is used to machine the C-276 nickel-based alloy, and its cutting performances are studied. Based on orthogonal experiment method, the influence of cutting parameters on tool life, material removal rates and surface roughness are investigated. Experimental research results indicate that the optimal cutting condition is a cutting speed of 50 m/min, depth of cut of 0.4 mm and feed rate of 0.15 mm/r if the tool life and material removal rates are considered comprehensively. In this case, the tool life is 32 min and material removal rates are 3000 mm^3/min, which is appropriate to the rough machining. If the tool life and surface roughness are considered, the better cutting condition is a cutting speed of 75 m/min, depth of cut of 0.6 mm and feed rate of 0.1 mm/r. In this case, the surface roughness is 0.59μm. Notch wear, flank wear, chipping at the tool nose, built-up edge（BUE） and micro-cracks are found when Ti（C7N3）-based cermet insert turned Hastelloy C-276. Oxidation, adhesive, abrasive and diffusion are the wear mechanisms, which can be investigated by the observations of scanning electron microscope and energy-dispersive spectroscopy. This research will help to guide studies on the evaluation of machining parameters to further advance the productivity of nickel based alloy Hastelloy C-276 machining.
文摘In this paper the CNC machining of St52 was modeled using an artificial neural network(ANN)in the form of a four-layer multi-layer perceptron(MLP).The cutting parameters used in the model were cutting fluid flow,feed rate,spindle speed and the depth of cut and the model output was the tool life.For obtaining more accuracy and spending less time Taguchi design of experiment(DOE)has been used and correlation between the output of the ANN and the experimental results was 96%.Further optimization process has been done by use of a genetic algorithm(GA).After optimization process tool life was increased about 8%equal to 33 min and was corroborated by experimental tests.This demonstrates that the coupling of an ANN with the GA optimization technique is a valid and useful approach to use.
