Deep-Hole Inner Diameter Measuring System Based on Non-contact Capacitance Sensor

A precise aperture measuring system of small deep holes with capacitance sensors is presented. Based on the working principle of non-contact capacitance sensors, influence of the edge effect of gauge head is studied, and one capacitance sensor for measuring the aperture of the small blind holes or through holes is introduced. The system is composed of one positioning device, one aperture measuring capacitance sensor, one measuring circuit, and software. This system employs visual CCD and two-dimensional mic...

Effectiveness analysis of methane-drainage by deep-hole controlled pre-splitting blasting for preventing coal and gas outburst

In the study of the application effectiveness of deep-hole controlled pre-splittingblasting technology,it was found through laboratory micro test and field study on a mine insouth China that under the technology,coal masses produce many irreversible cracks.Afterblasting,the nearer the distance from blasting hole,the larger the BET surface areaand volume ratio of the infiltration pore are;they increased by 11.47%and 5.73%,respectively.The coefficient of air permeability is increased 4 times.After 3 months,the gasdrainage rate was increased by 66%.In the first 15 days,the cumulative pumped gas was1.93 times of blasting before.The average absolute gas emission decreased by 63.46%.Experimental results show that deep-hole controlled pre-splitting blasting not only preventscoal and gas outburst,but also gives good economic results.

Numerical simulation and experiment analysis of improving permeability by deep-hole presplitting explosion in high gassy and low permeability coal seam

Created a new damage model for explosive for LS-DYNA3D,taking advantageof the Taylor method aimed at the high gassy and low permeability coal seam,and numericallysimulated and analyzed the deep-hole presplitting explosion.The entire processof explosion was represented,including cracks caused by dynamic pressure,transmissionand vibration superposition of stress waves,as well as cracks growth driven by gas generatedby explosion.The influence of the cracks generated in the process of explosion andthe performance of improving permeability caused by the difference of interval between.explosive holes were analyzed.A reasonable interval between explosive holes of deepholepresplitting explosions in high gassy and low permeability coal seams was proposed,and the resolution of gas drainage in high gassy and low permeability coal seam was putforward.

Numerical simulation of deep-hole resistivity anomaly caused by drilling construction in Xinfengjiang geoelectric station

The Xinfengjiang reservoir in Guangdong Province is one of the large reservoirs that have triggered earthquakes of magnitude greater than 6.Numerous earthquakes have occurred since the impoundment of the reservoir,making it one of the most active seismic zones in south China.In 2015,a set of deep-hole resistivity anomalies was observed in the Heping geoelectric station in Dongyuan county,located near the Xinfengjiang reservoir.After a field investigation,we found that a planned well drilling construction of new measuring channels was being carried out during that corresponding period of time.After careful comparison and analysis on the basis of the collected raw data,we had a reason to believe that drilling construction,rather than the inducement of the Xinfengjiang reservoir,was the main culprit for those unusual georesistivity values.So as to verify the above conjecture,we constructed a series of 3D finite element models based on the geological and hydrological infor-mation around Heping station and analyzed the drilling disturbances,respectively.Some significant conclusions were finally drawn according to the precise numerical simulation.This study gives a good example by combining numerical simulation with engineering practice as a way to understand the root cause of georesistivity anomalies in reality.

Numerical modeling of destress blasting for strata separation

Destress blasting(DB)implemented along the perimeter of safety pillars is a special application of destressing in coal longwall mining.The goal is to separate relatively more deformed mined areas from safety pillars,such as shaft pillars or cross-cut pillars,to reduce the transfer of high stresses to the protective pillar.This case study aims to numerically simulate selected destress blasts in the Czech part of the Upper Silesian Coal Basin and examine its impact on stress transfer to the safety pillar area.To separate the area between the protective pillar and the longwall(LW),two fans of five 93-mm blast holes(length of 93e100 m)were drilled from the gate roads into the overburden strata.Each set of blast holes was fired separately in two stages without time delay.The explosive charge(gelatin-type of explosive)of each stage is 3450 kg.The two DB stages were fired when the longwall face was approximately 158 m and 152 m away from the blast.A 3D mine-wide model is built and validated with in situ stress measured with hydrofracturing.Mining and destressing in three 5-m thick coal seams are simulated in the region.Numerical modeling of DB is successfully conducted using a rock fragmentation factor a of 0.05 and a stress reduction/dissipation factor β of 0.95.Buffering of transfer of additional stress from the mining area into the safety pillar is evaluated by comparison of yielding volume before and after DB.It is shown that yielding volume drops after DB by nearly 80%in the area of the destressing panel and near the safety shaft pillar.

近断层石门揭煤围岩控制技术研究

为研究断层影响下巷道围岩应力的演化规律,以近断层石门揭煤为研究背景,利用数值模拟手段对巷道围岩变形破坏进行分析,并提出了巷帮钻孔卸压技术措施。结果表明:受断层活化的影响,石门在揭煤过程中靠近断层的帮部应力集中程度高,垂直应力达到44 MPa;最佳卸压钻孔布置方案为钻孔直径300 mm、钻孔长度5 m和钻孔间距600 mm,该方案下原应力峰值区应力由44 MPa降低到28.64 MPa,应力释放率可达到35%,巷道围岩控制效果显著。该研究为断层构造下巷道围岩控制提供了一种新思路,可有效防治煤矿断层错动型冲击地压灾害。

特厚煤层掘进巷道两帮卸压钻孔合理参数数值模拟研究

目前钻孔卸压技术为冲击地压矿井巷道掘进期间防冲主要措施之一,钻孔布置和参数决定着卸压效果。目的为了探讨特厚煤层掘进巷道两帮卸压钻孔合理布置参数,方法基于耿村煤矿综放工作面运输巷道地质采矿条件,利用数值计算方法研究掘进巷道两帮在单排布置时孔深、孔径、孔间距,双排布置时排距等不同参数条件下,巷道围岩应力云图和两帮垂直应力分布特征。结果结果表明:(1)单排布置卸压钻孔时,随着孔深、孔径递增,巷道两帮高应力区逐渐向深部围岩转移,而巷道两帮浅部围岩处于低应力区。(2)当钻孔孔深、孔径达到一定值时,巷道两帮支承压力由“单峰型”转化为“双峰型”,浅部围岩处于临界卸压状态;随着孔深、孔径继续增加,巷道两帮处于过度卸压状态。(3)利用卸压后、无卸压时巷道两帮高应力区向深部围岩的转移量ΔL、峰值应力处距巷道表面距离的比值η表示临界卸压和过度卸压状态,确定出卸压钻孔的合理参数。在耿村煤矿13230综放工作面运输平巷进行超前钻孔卸压和锚网索+36U型可缩性金属支架二级支护后,对巷道两帮实施钻孔卸压防冲,效果显著。结论研究结果对冲击地压矿井回采巷道掘进期间的卸压防冲具有指导和借鉴意义。

Geomechanical effects of stress shadow created by large-scale destress blasting

This study aims to determine if large-scale choked panel destress blasting can provide sufficient beneficial stress reduction in highly-stressed remnant ore pillar that is planned for production. The orebody is divided into 20 stopes over 2 levels, and 2 panels are choke-blasted in the hanging wall to shield the ore pillar by creating a stress shadow around it. A linear-elastic model of the mining system is constructed with finite difference code FLAC3 D. The effect of destress blasting in the panels is simulated by applying a fragmentation factor(α) to the rock mass stiffness and a stress reduction factor(β) to the current state of stress in the region occupied by the destress panels. As an extreme case, the destress panel is also modeled as a void to obtain the maximum possible beneficial effects of destressing and stress shadow.Four stopes are mined in the stress shadow of the panels in 6 lifts and then backfilled. The effect of destress blasting on the remnant ore pillar is quantified based on stress change and brittle shear ratio(BSR) in the stress shadow zone compared to the base case without destress blasting. To establish realistic rock fragmentation and stress reduction factors, model results are compared to measured stress changes reported for case studies at Fraser and Brunswick mines. A 1.5 MPa immediate stress decrease was observed 20 m away from the panel at Fraser Mine, and a 4 MPa immediate stress decrease was observed 25 m away at Brunswick Mine. Comparable results are obtained from the current model with a rock fragmentation factor α of 0.2 and a stress reduction factor α of 0.8. It is shown that a destress blasting with these parameters reduces the major principal stress in the nearest stopes by 10-25 MPa.This yields an immediate reduction of BSR, which is deemed sufficient to reduce volume of ore at risk in the pillar.

Volumetric changes in the focal areas of seismic events corresponding to destress blasting

The typical development of total volumetric change in the focal areas of seismic events,corresponding to destress blasting,is characterized as an explosive phase followed by an implosive phase and with alternating additional phases following on from that.In a few cases,a non-typical development of volumetric change was identified,where the first phase was implosive and the second phase,explosive.This development is mainly typical for induced seismic events recorded during mining,not for destress blasting.Seismic events were recorded during longwall mining in the Czech part of the Upper Silesian Coal Basin,where the destress blasting technique is used as a rockburst prevention active measure.Kinematic source processes in the focal areas of selected seismic events were analyzed by the seismic moment tensor inversion method,as well as by studying geomechanical rock mass conditions at the localities of the seismic events.The main goal of the analysis was to attempt to identify the reasons for non-typical development of volumetric changes in these cases.Volumetric changes were analyzed for seismic events with energy greater than 104 J,recorded in the period of time from 1993 to 2009(1109 events).80%(891)of the recorded seismic events were induced seismic events that were registered during longwall mining and 20%(218)corresponded to destress blasting events.Research shows that the main reason for the non-typical development of volumetric changes in the focal areas of seismic events is an association with destress blasting in the rock mass,which is very close to rock mass overstressing.The detonation of explosives in boreholes,which would dominate the first phase of volumetric changes,probably obscured stress release in the rock mass,as manifested in the first implosion phase of the volumetric changes in this case.

Large-scale destress blasting for seismicity control in hard rock mines:A case study

Destress blasting is a rockburst control technique where highly stressed rock is blasted to reduce the local stress and stiffness of the rock,thereby reducing its burst proneness.The technique is commonly practiced in deep hard rock mines in burst prone developments,as well as in sill or crown pillars which become burst-prone as the orebody is extracted.Large-scale destressing is a variant of destress blasting where panels are created parallel to the orebody strike with a longhole,fanning blast pattern from cross cut drifts situated in the host rock.The aim of panel destressing is to reduce the stress concentration in the ore blocks or pillars to be mined.This paper focuses on the large-scale destress blasting program conducted at Vale's Copper Cliff Mine(CCM)in Ontario,Canada.The merits of panel destressing are examined through field measurements of mining induced stress changes in the pillar.The destressing mechanism is simulated with a rock fragmentation factor(a)and stress reduction/dissipation factor(b).A 3D model is built and validated with measured induced stress changes.It is shown that the best correlation between the numerical model and field measurements is obtained when the combination of a and b indicates that the blast causes high fragmentation(a=0.05)and high stress release(b=0.95)in the destress panel.It is demonstrated that the burst proneness of the ore blocks in the panel stress shadow is reduced in terms of the brittle shear ratio(BSR)and the burst potential index(BPI).

A comparison of seismic response to conventional and face destress blasting during deep tunnel development

A novel design of development face destress blasting was implemented during the construction of an experimental tunnel at great depth.A second tunnel was developed nearby using conventional blasting as a control.The tunnels were developed parallel to one another and perpendicular to a high subhorizontal stress.High resolution seismic monitoring was used to record and compare the seismic response generated by each excavation.Analysis of the seismic data from the conventionally blasted tunnel indicated that the seismogenic zone of stress-driven instability extended up to 3.6 m ahead of the face.Destress blasting within the corresponding zone of the adjacent tunnel had the effect of reducing the rock mass stiffness,primarily due to weakening of the pre-existing natural discontinuities.The reduction in rock mass stiffness was inferred from the spatial broadening of the seismogenic zone and associated reduction in the measured spatial density of events,radiated energy and seismic potency ahead of the face.High strain gradients around the unsupported portion of the conventionally blasted excavation were implied by the rate at which the spatial density of seismicity changed with respect to the tunnel face position.In contrast,the change in the spatial density of seismicity around the destressed development face was much more gradual.This was indicative of lower strain gradients in the rock there.A reduction in rock mass stiffness following destress blasting was also indicated by the much wider variety of seismic source mechanisms recorded adjacent to the destressed tunnel.Seismic source mechanisms associated with destress blasting were also more clearly characteristic of compressive overstressing with fracture closure.The source mechanism data also indicated that destress blasting induced instability on all natural joint sets.When compared to conventional development blasting,destress blasting typically reduced violent strain energy release from the rock mass and the associated seismicity,but not always.

Numerical Simulation of the Relationship between the Width of Destressed Zone and Blasthole Depth

Overstress in the surrounding rock of the roadway is a key reason that causes failures of deep roadways. Destressing blasting is one of the promising techniques that could improve the supporting quality. If the depth of the pressure relief blast hole is too shallow, the surrounding rock of the roadway will be broken or even collapsed. If the pressure relief blast hole is too deep, the pressure relief area will be located in the deep part of the surrounding rock of the roadway, which cannot achieve the purpose of releasing the stress in the shallow part of the surrounding rock and cause waste of the blast hole. The width or range of the pressure relief area should just fall in the high stress area of the surrounding rock of the roadway, so the pressure relief blast hole should have a reasonable depth. In order to quantitatively describe the relationship between borehole depth and the width of the stress relief zone, numerical simulations were carried out in ANSYS according to different borehole depths. The results show that the optimal destressing effect is achieved when borehole depth is 4 m. Peak stress of and is significantly reduced by 30.51% and 49.07% after blasting. Meanwhile, the high-stress area shifts about 4.8 m from the roadside to the depth of surrounding rock, thus a 3.8 m wide stress relief zone is formed around the roadside, thus, the aim of quantizing the effects of destress blasting is achieved.

Seismic evaluation of the destress blasting efficiency

In this paper, selected methods of destress blasting efficiency assessment are presented, and novel quantitative methods based on in situ seismic measurements are proposed. The newly formulated solution combines two different approaches. The first, which is useful mostly for the near-field seismic analyses, is based on the analysis of seismic amplitude characteristics, and the second, relevant for farfield evaluation, is extended by the duration and frequency of the seismic wave. Both approaches are based on the seismic analyses of the waveforms generated by blasting recorded by the local seismic network. The proposed solutions are tested and validated in deep underground mines in Poland in which the room-and-pillar mining method is applied. Based on performed analysis, it is shown that both methods may be used as a rockburst hazard control in underground mines. However, developed methods may also be successfully implemented in other engineering practices, including the assessment of seismic vibrations in open pits and quarries.

正断层上盘开采断层附近应力时空分布数值模拟

采动引起的断层错动是诱发矿震和断层冲击矿压的主要原因之一。在现有的数值模拟研究中,断层上测点的数量较少,以致于对断层各处力学状态全貌的了解较为困难。而且,针对煤层应力分布的研究通常仅限于垂直应力(支承压力),而对其它应力尚缺乏了解。为研究采动条件下断层附近应力时空分布,采用FLAC^(3D)建立了正断层上盘开采的数值模型。模型中共包括13个岩层和1个45°倾角的正断层,通过计算获得了工作面从断层上盘推进过程中断层各处及附近煤层应力的时空分布规律。监测了断层上盘断层上的22个节点以获取断层各处力学状态全貌。研究发现,在工作面推进过程中,断层上存在1个压紧区及1个或多个松动区;断层上的压紧区较为安全,压紧区上、下方松动区的正应力越来越低,当工作面邻近断层时该区的断层区段多趋于危险,该区范围最大为78 m;断层上盘煤层紧邻工作面煤壁的垂直、水平和切应力峰值分别位于煤壁前方7.5~10.5、10.5~15.5和11.5~12.5 m;断层下盘煤层3种应力最大值均上升或有上升趋势。当工作面煤壁距断层的水平距离由40 m减小至20 m时,断层上盘煤层垂直、水平和切应力受断层影响较显著的区域通常分别在距断层3.5、10.5 m和3.5 m以内。

卸压开采顶板巷道破坏特征及稳定性分析

通过物理模拟实验显示上行卸压开采顶板岩层运动状况,分析了不同区域顶板巷道的采动破坏特征;利用长距离钻孔跟踪探测桃园煤矿上行开采顶板岩体的裂隙发育过程,得到了顶板不同区域巷道围岩的裂隙分区特征,并推断出该特定条件下上覆岩层采动稳定周期为165 d;采用FLAC软件进一步研究了不同侧压系数和采动应力环境下的顶板巷道的椭圆形断面形状,指出底板必要的加固深度为4.0～6.0 m,明确了卸压区顶板巷道维护的基本原则和控制方法。

深井煤巷钻孔卸压技术的数值模拟与工业试验

结合工程实例,利用数值模拟方法研究了钻孔卸压的作用机理、巷道围岩动态损伤破坏发展和应力场重新分布的过程.模拟发现:合理布置的卸压孔可以导致巷帮围岩的结构性预裂破坏,从而使围岩高应力向深部转移;在卸压孔和锚网联合支护后改善了围岩附近的应力环境,改变了围岩破坏的时空次序,对控制围岩变形和破坏具有突出的优越性.

巷道卸压法应力迁变规律及卸压参数的确定

北洺河铁矿-95 m 水平4#采场进路联巷及回采进路在掘进过程中或成巷后不久就发生片帮冒顶,采用密集的 U 型可缩式金属拱架仍未能控制住巷道围岩的变形与破坏。利用 flac3d 数值模拟的方法研究了不同卸压高度和宽度下采场进路应力分布状态,模拟结果表明,卸压对巷道不同部位的不同应力具有不同程度的卸压效果,卸压可有效降低仰拱处剪应力及巷道仰拱、两帮和底角的最大主应力,巷道顶底板的最大主应力随卸压工程的开挖而增加,卸压宽度对卸压效果影响显著,在北洺河铁矿条件下卸压工程超出巷道边界1～2 m 为宜。根据数值模拟结果和-80 m 分段回采界线的位置,确定卸压工程范围,采用房柱法进行卸压后,采场的应力集中程度得到有效降低,安全回采矿石15万 t,并为高应力矿山开采提供了卸压开采的新思路。

巷道底臌的挠曲效应及卸压效果的分析

本文借助弹塑性薄板理论,对巷道底臌的机理进行了分析,得出巷道底臌的主要原因之一是底板完整岩层的失稳并向巷道内挠曲。通过理论推导,求出了底板的极限承载能力。同时对目前所采用的卸压法控制底臌的效果进行了分析,指出使用卸压法与底板加固相结合的支护方式更为有利。最后通过实例分析,对上述结论进行了验证。

圆形断面巷道爆破卸压机理数值模拟研究

运用岩石破裂过程分析系统RFPA2D,充分考虑岩石非均匀性等复杂的岩石力学性质,对爆生裂隙带、爆炸空腔构成的爆破卸压带维护巷道的作用机理进行模拟研究,有助于提高人们在巷道维护方法中的认识。

深部强冲击厚煤层开采上、下解放层卸压效果相似模拟试验研究

为了研究深部强冲击厚煤层开采上、下解放层的卸压效果,采用相似材料模拟试验的方法,通过监测解放层开采过程中及稳定后被解放层应力变化情况,分析应力变化规律,计算下解放层下部合理卸压角,确定了被解放层下平巷的合理位置;比较两次开采上解放层模拟试验的卸压程度,确定了上解放层工作面的合理位置;证明了开采下解放层后,被解放层上平巷附近区域仍是高应力集中区,易发生冲击地压,而开采上解放层后,该区应力明显减小,说明上解放层卸压效果明显;验证了井下发生大能量冲击地压之前,地表沉降出现"反弹"的异常现象。该研究为工作面开采设计提供理论指导,对防治冲击地压具有重要的现实意义。