Analyzed and calculated are pressure changes and body deformation of the sample inside of the corer in the process of sampling of deep-sea shallow sediment with a non-piston corer for gas hydrate investigation, Two co...Analyzed and calculated are pressure changes and body deformation of the sample inside of the corer in the process of sampling of deep-sea shallow sediment with a non-piston corer for gas hydrate investigation, Two conclusions are drawn: (1) the stress increments associated with the corer through the sampling process do not affect the stabilization of the gas hydrate; (2) the body deformation of the sample is serious and the "incremental filling ratio" (IFR) is less than unit, For taking samples with in-situ pressure and structure, combining with the design theories of the pressure tight corer, we have designed a kind of piston corer, named the gas hydrate pressure tight piston corer, Several tests on the sea have been conducted. Test results indicate that the piston corer has a good ability of taking sediment samples on the seafloor and maintaining their original in-situ pressure, meeting the requirement of exploration of gas hydrate in deep-sea shallow sediment layers.展开更多
Compressed gas is usually used for the pressure compensation of the deep-sea pressure-maintaining sampler.The pressure and volume of the recovered fluid sample are highly related to the precharged gas. To better under...Compressed gas is usually used for the pressure compensation of the deep-sea pressure-maintaining sampler.The pressure and volume of the recovered fluid sample are highly related to the precharged gas. To better understand the behavior of the gas under high pressure, we present a new real gas state equation based on the compression factor Z which was derived from experimental data. Then theoretical calculation method of the pressure and volume of the sample was introduced based on this empirical gas state equation. Finally, the proposed calculation method was well verified by the high-pressure vessel experiment of the sampler under 115 MPa.展开更多
The accumulator is used as a pressure compensation device to realize deep-sea microbe gastight sampling. Four key states of the accumulator are proposed to describe the pressure compensation process and a correspondin...The accumulator is used as a pressure compensation device to realize deep-sea microbe gastight sampling. Four key states of the accumulator are proposed to describe the pressure compensation process and a corresponding mathematical model is established to investigate the relationship between the results of pressure compensation and the parameters of the accumulator. Simulation results show that during the falling process of the sampler, the accumulator' s real opening pressure is greater than its precharge pressure; when the sampling depth is 6000 m and the accumulator' s precharge pressure is less than 30 MPa, to increase the accumulator' s precharge pressure can improve pressure compensation results obviously. Laboratory experiments at 60 MPa show that the acctunulator is an effective and reliable pressure compensation device for deep-sea microbe samplers, The success in sea trial at a depth of 2000 m in the South China Sea shows that the mathematical model and laboratory experiment results are reliable.展开更多
The deep cement mixing(DCM)is used to improve the capacity and reduce the settlement of the soft ground by forming cemented clay columns.The investigation on the mechanical behaviour of the DCM samples is limited to e...The deep cement mixing(DCM)is used to improve the capacity and reduce the settlement of the soft ground by forming cemented clay columns.The investigation on the mechanical behaviour of the DCM samples is limited to either laboratory-prepared samples or in-situ samples under unconfined compression.In this study,a series of drained and undrained triaxial shearing tests was performed on the in-situ cored DCM samples with high cement content to assess their mechanical behaviours.It is found that the drainage condition affects significantly the stiffness,peak and residual strengths of the DCM samples,which is mainly due to the state of excess pore water pressure at different strain levels,i.e.being positive before the peak deviatoric stress and negative after the peak deviatoric stress,in the undrained tests.The slope of the failure envelope changes obviously with the confining pressures,being steeper at lower stress levels and flatter at higher stress levels.The strength parameters,effective cohesion and friction angle obtained from lower stress levels(c′0 andφ′0)are 400 kPa and 58°,respectively,which are deemed to be true for design in most DCM applications where the in-situ stress levels are normally at lower values of 50-200 kPa.Additionally,the computed tomography(CT)scanning system was adopted to visualize the internal structures of DCM samples.It is found that the clay pockets existing inside the DCM samples due to uneven mixing affect markedly their stress-strain behaviour,which is one of the main reasons for the high variability of the DCM samples.展开更多
The development of a core collection could enhance the utilization of germplasm collections in crop improvement programs and simplify their management. Selection of an appropriate sampling strategy is an important pre...The development of a core collection could enhance the utilization of germplasm collections in crop improvement programs and simplify their management. Selection of an appropriate sampling strategy is an important prerequisite to construct a core collection with appropriate size in order to adequately represent the genetic spectrum and maximally capture the genetic diversity in available crop collections. The present study was initiated to construct nested core collections to determine the appropriate sample size to represent the genetic diversity of rice landrace collection based on 15 quantitative traits and 34 qualitative traits of 2 262 rice accessions. The results showed that 50-225 nested core collections, whose sampling rate was 2.2%-9.9%, were sufficient to maintain the maximum genetic diversity of the initial collections. Of these, 150 accessions (6.6%) could capture the maximal genetic diversity of the initial collection. Three data types, i.e. qualitative traits (QT1), quantitative traits (QT2) and integrated qualitative and quantitative traits (QTT), were compared for their efficiency in constructing core collections based on the weighted pair-group average method combined with stepwise clustering and preferred sampling on adjusted Euclidean distances. Every combining scheme constructed eight rice core collections (225, 200, 175, 150, 125, 100, 75 and 50). The results showed that the QTT data was the best in constructing a core collection as indicated by the genetic diversity of core collections. A core collection constructed only on the information of QT1 could not represent the initial collection effectively. QTT should be used together to construct a productive core collection.展开更多
Nutrient release from the dredged and undredged sediments in Lake Kasumigaura were simulated under the laboratory control conditions with large-size core samples. It was found that phosphate and ammonia release fluxes...Nutrient release from the dredged and undredged sediments in Lake Kasumigaura were simulated under the laboratory control conditions with large-size core samples. It was found that phosphate and ammonia release fluxes are less in aerobic than those in anaerobic. In different simulated dredged depth, the phosphate release showed large divergence in the anaerobic than in the aerobic. There was a larger accumulated release of phosphate and ammonia at actual dredged (St. B) than the undredged (St. A) in anaerobic condition. This showed that the sludge-dredging was effective of controlling phosphorus and nitrogen release. A preliminary assessment is drawn from the experiments that the sludge-dredging work in Tsuchiura Bay of Lake Kasumigaura can reduce about 15. 9% of phospbate and 56. 2% of anunonia release from the sediments respectively.展开更多
Sediment core IR-GC1, from the abyssal basin of the Indian Ocean off Sumatra, may provide important information on depositional events related to earthquakes and tsunamis. In this study, based on a combination of grai...Sediment core IR-GC1, from the abyssal basin of the Indian Ocean off Sumatra, may provide important information on depositional events related to earthquakes and tsunamis. In this study, based on a combination of grain-size analysis with lithological studies and oxygen isotope stratigraphy, seven deep-sea turbidite layers were identified, corresponding to seven turbidity events that occurred at 128- 130, 105-107, 98-100, 86-87, 50-53, 37-41 and 20-29 ka. The sediments of the turbidite deposits are characterized by coarse grain sizes, poor sorting, wide kurtosis, bimodal frequency distributions and clear depositional variations. Particle size grading is also an important signature of deep-sea turbidite deposits and can be used as an indicator to identify turbidite layers. Possible triggering mechanisms for the turbidite events include tsunamis, earthquakes, volcanic eruptions and sea-level changes.展开更多
A novel statistical approach to evaluate the manufacturing quality of press coated tablets in terms of the centering of their core is presented. We also provide a formula to determine the necessary sample size. This a...A novel statistical approach to evaluate the manufacturing quality of press coated tablets in terms of the centering of their core is presented. We also provide a formula to determine the necessary sample size. This approach is applied to real data.展开更多
Dust phenomenon is one of the biggest environmental problems in arid and semiarid regions. In these areas, lakes and wetlands are natural dust traps and core sampling method can be an appropriate way to assess the phe...Dust phenomenon is one of the biggest environmental problems in arid and semiarid regions. In these areas, lakes and wetlands are natural dust traps and core sampling method can be an appropriate way to assess the phenomenon of the dust. Therefore, the purpose of this study is the study of frequency and characteristics of dust sediments in core samples from Hashilan wetlands, Kermanshah. Four intact core samples were taken from different parts of the Hashilan wetland in Kermanshah. Physical, chemical and micromorphological analysis were done. Also clay mineralogy was performed using X-ray analysis (XRD) and shape of particles was photographed by scanning electron microscope (SEM). Considering that four samples had been taken from different parts of the wetland, the quantitative differences in dust amount are likely due to the location of the samples. The results of XRD and thin sections show that the dominant mineralogical composition of dust particles was clay minerals, quartz and calcite. SEM results for core sample 1 revealed that most particles had the size between 2 to 50 mm which ranged from fine silt to coarse silt. Considering the similarities between SEM images for core sample 1 and those from Kermanshah dust measurement station, it could be said that fine rounded particles detected at top 30 cm of core samples had Aeolian origin. These findings were in accordance with the results from dust measurement and weather station of Kermanshah about increased dust activities in the study area over past 10 years.展开更多
基金The project was financially supported bythe National Natural science Foundation of China (Grant No.50675055)
文摘Analyzed and calculated are pressure changes and body deformation of the sample inside of the corer in the process of sampling of deep-sea shallow sediment with a non-piston corer for gas hydrate investigation, Two conclusions are drawn: (1) the stress increments associated with the corer through the sampling process do not affect the stabilization of the gas hydrate; (2) the body deformation of the sample is serious and the "incremental filling ratio" (IFR) is less than unit, For taking samples with in-situ pressure and structure, combining with the design theories of the pressure tight corer, we have designed a kind of piston corer, named the gas hydrate pressure tight piston corer, Several tests on the sea have been conducted. Test results indicate that the piston corer has a good ability of taking sediment samples on the seafloor and maintaining their original in-situ pressure, meeting the requirement of exploration of gas hydrate in deep-sea shallow sediment layers.
基金The National Key Research and Development Program of China under contract Nos 2018YFC0310600 and2016YFC0300500。
文摘Compressed gas is usually used for the pressure compensation of the deep-sea pressure-maintaining sampler.The pressure and volume of the recovered fluid sample are highly related to the precharged gas. To better understand the behavior of the gas under high pressure, we present a new real gas state equation based on the compression factor Z which was derived from experimental data. Then theoretical calculation method of the pressure and volume of the sample was introduced based on this empirical gas state equation. Finally, the proposed calculation method was well verified by the high-pressure vessel experiment of the sampler under 115 MPa.
文摘The accumulator is used as a pressure compensation device to realize deep-sea microbe gastight sampling. Four key states of the accumulator are proposed to describe the pressure compensation process and a corresponding mathematical model is established to investigate the relationship between the results of pressure compensation and the parameters of the accumulator. Simulation results show that during the falling process of the sampler, the accumulator' s real opening pressure is greater than its precharge pressure; when the sampling depth is 6000 m and the accumulator' s precharge pressure is less than 30 MPa, to increase the accumulator' s precharge pressure can improve pressure compensation results obviously. Laboratory experiments at 60 MPa show that the acctunulator is an effective and reliable pressure compensation device for deep-sea microbe samplers, The success in sea trial at a depth of 2000 m in the South China Sea shows that the mathematical model and laboratory experiment results are reliable.
基金funded by the Environment and Conservation Fund(Grant Nos.2020-170 and 2021-156)the National Natural Science Foundation of China(Grant No.42102327).
文摘The deep cement mixing(DCM)is used to improve the capacity and reduce the settlement of the soft ground by forming cemented clay columns.The investigation on the mechanical behaviour of the DCM samples is limited to either laboratory-prepared samples or in-situ samples under unconfined compression.In this study,a series of drained and undrained triaxial shearing tests was performed on the in-situ cored DCM samples with high cement content to assess their mechanical behaviours.It is found that the drainage condition affects significantly the stiffness,peak and residual strengths of the DCM samples,which is mainly due to the state of excess pore water pressure at different strain levels,i.e.being positive before the peak deviatoric stress and negative after the peak deviatoric stress,in the undrained tests.The slope of the failure envelope changes obviously with the confining pressures,being steeper at lower stress levels and flatter at higher stress levels.The strength parameters,effective cohesion and friction angle obtained from lower stress levels(c′0 andφ′0)are 400 kPa and 58°,respectively,which are deemed to be true for design in most DCM applications where the in-situ stress levels are normally at lower values of 50-200 kPa.Additionally,the computed tomography(CT)scanning system was adopted to visualize the internal structures of DCM samples.It is found that the clay pockets existing inside the DCM samples due to uneven mixing affect markedly their stress-strain behaviour,which is one of the main reasons for the high variability of the DCM samples.
基金supported by the National Natural Science Foundation of China (Grant No. 30700494)the Principal Fund of South China Agricultural University, China (Grant No. 2003K053)
文摘The development of a core collection could enhance the utilization of germplasm collections in crop improvement programs and simplify their management. Selection of an appropriate sampling strategy is an important prerequisite to construct a core collection with appropriate size in order to adequately represent the genetic spectrum and maximally capture the genetic diversity in available crop collections. The present study was initiated to construct nested core collections to determine the appropriate sample size to represent the genetic diversity of rice landrace collection based on 15 quantitative traits and 34 qualitative traits of 2 262 rice accessions. The results showed that 50-225 nested core collections, whose sampling rate was 2.2%-9.9%, were sufficient to maintain the maximum genetic diversity of the initial collections. Of these, 150 accessions (6.6%) could capture the maximal genetic diversity of the initial collection. Three data types, i.e. qualitative traits (QT1), quantitative traits (QT2) and integrated qualitative and quantitative traits (QTT), were compared for their efficiency in constructing core collections based on the weighted pair-group average method combined with stepwise clustering and preferred sampling on adjusted Euclidean distances. Every combining scheme constructed eight rice core collections (225, 200, 175, 150, 125, 100, 75 and 50). The results showed that the QTT data was the best in constructing a core collection as indicated by the genetic diversity of core collections. A core collection constructed only on the information of QT1 could not represent the initial collection effectively. QTT should be used together to construct a productive core collection.
文摘Nutrient release from the dredged and undredged sediments in Lake Kasumigaura were simulated under the laboratory control conditions with large-size core samples. It was found that phosphate and ammonia release fluxes are less in aerobic than those in anaerobic. In different simulated dredged depth, the phosphate release showed large divergence in the anaerobic than in the aerobic. There was a larger accumulated release of phosphate and ammonia at actual dredged (St. B) than the undredged (St. A) in anaerobic condition. This showed that the sludge-dredging was effective of controlling phosphorus and nitrogen release. A preliminary assessment is drawn from the experiments that the sludge-dredging work in Tsuchiura Bay of Lake Kasumigaura can reduce about 15. 9% of phospbate and 56. 2% of anunonia release from the sediments respectively.
基金granted by the National Natural Science Foundation of China(Grant No.41106052)China Ocean Mineral Resources R&D Association project (DY125-12-R-03)the Fundamental Research Funds for National Nonprofit Institute Grant(JG1511)
文摘Sediment core IR-GC1, from the abyssal basin of the Indian Ocean off Sumatra, may provide important information on depositional events related to earthquakes and tsunamis. In this study, based on a combination of grain-size analysis with lithological studies and oxygen isotope stratigraphy, seven deep-sea turbidite layers were identified, corresponding to seven turbidity events that occurred at 128- 130, 105-107, 98-100, 86-87, 50-53, 37-41 and 20-29 ka. The sediments of the turbidite deposits are characterized by coarse grain sizes, poor sorting, wide kurtosis, bimodal frequency distributions and clear depositional variations. Particle size grading is also an important signature of deep-sea turbidite deposits and can be used as an indicator to identify turbidite layers. Possible triggering mechanisms for the turbidite events include tsunamis, earthquakes, volcanic eruptions and sea-level changes.
文摘A novel statistical approach to evaluate the manufacturing quality of press coated tablets in terms of the centering of their core is presented. We also provide a formula to determine the necessary sample size. This approach is applied to real data.
文摘Dust phenomenon is one of the biggest environmental problems in arid and semiarid regions. In these areas, lakes and wetlands are natural dust traps and core sampling method can be an appropriate way to assess the phenomenon of the dust. Therefore, the purpose of this study is the study of frequency and characteristics of dust sediments in core samples from Hashilan wetlands, Kermanshah. Four intact core samples were taken from different parts of the Hashilan wetland in Kermanshah. Physical, chemical and micromorphological analysis were done. Also clay mineralogy was performed using X-ray analysis (XRD) and shape of particles was photographed by scanning electron microscope (SEM). Considering that four samples had been taken from different parts of the wetland, the quantitative differences in dust amount are likely due to the location of the samples. The results of XRD and thin sections show that the dominant mineralogical composition of dust particles was clay minerals, quartz and calcite. SEM results for core sample 1 revealed that most particles had the size between 2 to 50 mm which ranged from fine silt to coarse silt. Considering the similarities between SEM images for core sample 1 and those from Kermanshah dust measurement station, it could be said that fine rounded particles detected at top 30 cm of core samples had Aeolian origin. These findings were in accordance with the results from dust measurement and weather station of Kermanshah about increased dust activities in the study area over past 10 years.