Analytical solution for the stress field of hierarchical defects:multiscale framework and applications

Hierarchical defects are defined as adjacent defects at different length scales.Involved are the two scales where the stress field distribution is interrelated.Based on the complex variable method and conformal mapping,a multiscale framework for solving the problems of hierarchical defects is formulated.The separated representations of mapping function,the governing equations of potentials,and the stress field are subsequently obtained.The proposed multiscale framework can be used to solve a variety of simplified engineering problems.The case in point is the analytical solution of a macroscopic elliptic hole with a microscopic circular edge defect.The results indicate that the microscopic defect aggregates the stress concentration on the macroscopic defect and likely leads to global propagation and rupture.Multiple micro-defects have interactive effects on the distribution of the stress field.The level of stress concentration may be reduced by the coalescence of micro-defects.This work provides a unified method to analytically investigate the influence of edge micro-defects within the scope of multiscale hierarchy.The formulated multiscale approach can also be potentially applied to materials with hierarchical defects,such as additive manufacturing and bio-inspired materials.

Effect of Modulus Heterogeneity on the Equilibrium Shape and Stress Field ofαPrecipitate in Ti-6Al-4V

For media with inclusions(e.g.,precipitates,voids,reinforcements,and others),the difference in lattice parameter and the elastic modulus between the matrix and inclusions cause stress concentration at the interfaces.These stress fields depend on the inclusions’size,shape,and distribution and will respond instantly to the evolving microstructure.This study develops a phase-field model concerningmodulus heterogeneity.The effect of modulus heterogeneity on the growth process and equilibrium state of theαplate in Ti-6Al-4V during precipitation is evaluated.Theαprecipitate exhibits strong anisotropy in shape upon cooling due to the interplay of the elastic strain and interfacial energy.The calculated orientation of the habit plane using the homogeneous modulus ofαphase shows the smallest deviation fromthat of the habit plane observed in the experiment,compared to the case where the homogeneous modulus ofβphase is adopted.In addition,the equilibrium volume ofαphase within the systemusing homogeneousβmodulus exhibits the largest dependency on the applied stresses.The stress fields across theα/βinterface are further calculated under the assumption of modulus heterogeneity and compared to those using homogeneous modulus of eitherαorβphase.This study provides an essential theoretical basis for developing mechanics models concerning systems with heterogeneous structures.

The 2023 Turkey earthquake doublet: Earthquake relocation, seismic tomography, and stress field inversion

On February 6,2023,two earthquakes with magnitudes of M_(W) 7.8 and M_(W) 7.5 struck southeastern Turkey,causing significant casualties and economic losses.These seismic events occurred along the East Anatolian Fault Zone,a convergent boundary between the Arabian Plate and the Anatolian Subplate.In this study,we analyze the M_(W) 7.8 and M_(W) 7.5 earthquakes by comparing their aftershock relocations,tomographic images,and stress field inversions.The earthquakes were localized in the upper crust and exhibited steep dip angles.Furthermore,the aftershocks occurred either close to the boundaries of low and high P-wave velocity anomaly zones or within the low P-wave velocity anomaly zones.The East Anatolia Fault,associated with the M_(W) 7.8 earthquake,and the SürgüFault,related to the M_(W) 7.5 earthquake,predominantly experienced shear stress.However,their western sections experienced a combination of strike-slip and tensile stresses in addition to shear stress.The ruptures of the M_(W) 7.8 and M_(W) 7.5 earthquakes appear to have bridged a seismic gap that had seen sparse seismicity over the past 200 years prior to the 2023 Turkey earthquake sequence.

Simulation Analysis of Stress Field of Walnut Shell Composite Powder in Laser Additive Manufacturing Forming

A calculation model of stress field in laser additive manufacturing of walnut shell composite powder(walnut shell/Co-PES powder)was established.The DFLUX subroutine was used to implement the moveable application of a double ellipsoid heat source by considering the mechanical properties varying with temperature.The stress field was simulated by the sequential coupling method,and the experimental results were in good accordance with the simulation results.In addition,the distribution and variation of stress and strain field were obtained in the process of laser additive manufacturing of walnut shell composite powder.The displacement of laser additive manufacturing walnut shell composite parts gradually decreased with increasing preheating temperature,decreasing laser power and increasing scanning speed.During the cooling process,the displacement of laser additive manufacturing of walnut shell composite parts gradually increased with the increasing preheating temperature,decreasing scanning speed and increasing laser power.

Effect of hydraulic fracturing induced stress field on weak surface activation during unconventional reservoir development

Unconventional reservoirs usually contain many weak surfaces such as faults,laminae and natural fractures,and effective activation and utilization of these weak surfaces in reservoirs can significantly improve the extraction effect.In hydraulic fracturing,when the artificial fracture approaches the natural fracture,the natural fracture would be influenced by both the original in-situ stress field and the hydraulic fracturing-induced stress field.In this paper,the hydraulic fracturing-induced stress field is calculated based on the relative position of hydraulic fracture and natural fracture,the original in-situ stress,the net pressure inside the hydraulic fracture and the pore pressure of the formation.Furthermore,the stability model of the natural fracture is established by combining the Mohr-Coulomb rupture criterion,and extensive parametric studies are conducted to explore the impact of each parameter on the stability of the natural fracture.The validity of the proposed model is verified by comparing with the reservoir characteristics and fracturing process of the X-well 150e155 formation in the Songliao Basin.It is found that the stress field induced by the hydraulic fracture inhibits the activation of the natural fracture after the artificial fracture crossed the natural fracture.Therefore,for similar reservoirs as X-well 150e155,it is suggested to connect natural fractures with hydraulic fractures first and then activate natural fractures which can effectively utilize the natural fractures and form a complex fracture network.

Tensile Fractures and in situ Stress Measurement Data Constraints on Cretaceous-Present Tectonic Stress Field Evolution of the Tanlu Fault Zone in Shandong Province,North China Craton

Tectonic stress fields are the key drivers of tectonic events and the evolution of regional structures.The tectonic stress field evolution of the Tanlu fault zone in Shandong Province,located in the east of the North China Craton(NCC),may have preserved records of the NCC’s tectonic history.Borehole television survey and hydraulic fracturing were conducted to analyze the paleo and present tectonic stress fields.Three groups of tensile fractures were identified via borehole television,their azimuths being NNW-SSE,NW-SE and NE-SW,representing multiple stages of tectonic events.Hydraulic fracturing data indicates that the study region is experiencing NEE-SWW-oriented compression and nearly-N-Soriented extension,in accordance with strike-slip and compression.Since the Cretaceous,the orientation of the extensional stress has evolved counterclockwise and sequentially from nearly-NW-SE-oriented to NE-SW-oriented and even nearly N-S-oriented,the stress state having transitioned from strike-slip-extension to strike-slip-compression,in association with the rotating and oblique subduction of the Pacific Plate beneath the NCC,with the participation of the Indian Plate.

3-D finite element modeling for evolution of stress field and interaction among strong earthquakes in Sichuan-Yunnan region

Based on the latest achievement about activities of geological structure, a 3-D finite-element model containing four layers of upper crust, lower crust (two layers) and upper mantle is established in the paper. By repeated tests and revisions, the boundary conditions of the model are determined. And then the background stress field, the stress field caused by fault creep and the stress field triggered by strong earthquake in Sichuan-Yunnan region, as well as their dynamic variations are calculated. The results indicate that the latter earthquake often occurs in the area with positive Coulomb rupture stress change associated with the former one, the former earthquake has a triggering effect on the latter one to a certain extent, and strong earthquake often occur in groups under the background of high stress, which is of great significance for distinguishing seismic anomalies, as well as for improving the level of earthquake prediction.

Contemporary tectonic stress field in China

The contemporary tectonic stress field in China is obtained on the basis of Chinese stress field database and Harvard CMT catalogue. Result of the inverted tectonic stresses shows that the maximum principal stress axis strikes nearly north-south direction in the west part of Tibet plateau, ENE direction in North China. In Central China, its strikes show a ra- diated pattern, i.e., NNE in north part and NNW in south part. The detailed stress field parameters of nearly whole China are given and can be used in geodynamic stress field simulation and earthquake prediction.

The Structure of Ore-controlling Strain and Stress Fields in the Shangzhuang Gold Deposit in Shandong Province,China

The Shangzhuang altered-rock type gold ore deposit is located in the middle segment of and controlled by the Wang＇ershan fault zone in the northwestern part of the Jiaodong gold province, China. The deformation evolution, the structure of strain and stress fields and its ore-controlling effect in the Shangzhuang deposit are discussed in this paper. It is revealed that the deformation evolution has mainly undergone four phases： the early ductile deformation, the second NE-striking horizontal simple shear, the third NE-striking compression-shear and the final NW-striking compression. The mineralization happened during the third stage in which the maximum principal stress gradually transited from NE to NW. The 3-D numerical simulations of the stress field show that, on the condition that the maximum principal stress is NE-striking, the fracture development in the fault zone is favored, while when the maximum principal stress is NW-striking, the fault zone is relatively extensional and it is suitable for the influx and emplacement of ore-forming fluids. The compression-shear strain field during the mineralization is characterized by the λ-type structure, the positive flower structure, etc. Orebodies are mostly equidistantly located in the dilatational spaces, which are distributed in the integral compressional circumstances. And the dilatational spaces are developed where the fault attitude changes or shear joint systems develop. In the overall compression-shear stress field, the strain field bears self-similarity at multiple scales, including the orebody, ore deposit and orefield. The selfsimilarity of the structure comprises the subequidistant distribution of fractures at the same scale and the similar shape of the fractures at various scales. Yet, due to the special geological structure, the orebodies are mostly located in the hanging wall in the Shangzhuang deposit, which is different from most deposits in the Jiaodong gold province. Analyses of the ore-controlling stress and strain fields in the deposit provide an important basis for deposit seeking.

Source mechanism of small-moderate earthquakes and tectonic stress field in Yunnan Province

In the paper, source mechanisms of 33 small-moderate earthquakes occurred in Yunnan are determined by modeling of regional waveforms from Yunnan digital seismic network. The result shows that most earthquakes occurred within or near the Chuandian rhombic block have strike-slip mechanism. The orientations of maximum compressive stresses obtained from source mechanism are changed from NNW-SSN to NS in the areas from north to south of the block, and tensile stresses are mainly in ENE-WSW or NE-SE. In the eastern Tibetan Plateau, the orientations of maximum compressive stress radiate toward outside from the plateau, and the tensile stress orientations mostly parallel to arc structures. Near 28N the orientations of both maximum compressive stress and tensile stress changed greatly, and the boundary seems to correspond to the southwestern extended line of Longmenshan fault. Outside of the Chuandian rhombic block, the orientations of P and T axes are some different from those within the block. The comparison shows that the source mechanism of small-moderate events presented in the paper is consistence with that of moderate-strong earthquakes determined by Harvard University, which means the source mechanism of small-moderate events can be used to study the tectonic stress field in this region.

Crustal stress field in Yunnan: implication for crust-mantle coupling

We applied the g CAP algorithm to determine 239 focal mechanism solutions 3：0≤MW≤ 6：0） with records of dense Chin Array stations deployed in Yunnan,and then inverted 686 focal mechanisms（including 447 previous results） for the regional crustal stress field with a damped linear inversion. The results indicate dominantly strike-slip environment in Yunnan as both the maximum（r1） and minimum（r3） principal stress axes are sub-horizontal. We further calculated the horizontal stress orientations（i.e., maximum and minimum horizontal compressive stress axes： S H and S h, respectively） accordingly and found an abrupt change near ＊26°N. To the north, S H aligns NW-SE to nearly E-W while S h aligns nearly N-S. In contrast, to the south, both S H and S h rotate laterally and show dominantly fan-shaped patterns. The minimum horizontal stress（i.e., maximum strain axis） S h rotates from NW-SE to the west of Tengchong volcano gradually to nearly E-W in west Yunnan, and further toNE-SW in the South China block in the east. The crustal strain field is consistent with the upper mantle strain field indicated by shear-wave splitting observations in Yunnan but not in other regions. Therefore, the crust and upper mantle in Yunnan are coupled and suffering vertically coherent pure-shear deformation in the lithosphere.

Active Faulting Pattern,Present-day Tectonic Stress Field and Block Kinematics in the East Tibetan Plateau

This paper examines major active faults and the present-day tectonic stress field in the East Tibetan Plateau by integrating available data from published literature and proposes a block kinematics model of the region. It shows that the East Tibetan Plateau is dominated by strike-slip and reverse faulting stress regimes and that the maximum horizontal stress is roughly consistent with the contemporary velocity field, except for the west Qinling range where it parallels the striking of the major strike-slip faults. Active tectonics in the East Tibetan Plateau is characterized by three faulting systems. The left-slip Kunlun-Qinling faulting system combines the east Kunlun fault zone, sinistral oblique reverse faults along the Minshan range and two major NEE-striking faults cutting the west Qinling range, which accommodates eastward motion, at 10--14 mm/a, of the Chuan-Qing block. The left-slip Xianshuihe faulting system accommodated clockwise rotation of the Chuan-Dian block. The Longmenshan thrust faulting system forms the eastern margin of the East Tibetan Plateau and has been propagated to the SW of the Sichuan basin. Crustal shortening across the Longmenshan range seems low （2-4 mm/a） and absorbed only a small part of the eastward motion of the Chuan-Qing block. Most of this eastward motion has been transmitted to South China, which is moving SEE-ward at 7-9 mm/a. It is suggested from geophysical data interpretation that the crust and lithosphere of the East Tibetan Plateau is considerably thickened and theologically layered. The upper crust seems to be decoupled from the lower crust through a decollement zone at a depth of 15-20 kin, which involved the Longmenshan fault belt and propagated eastward to the SW of the Sichuan basin. The Wenchuan earthquake was just formed at the bifurcated point of this decollement system. A rheological boundary should exist beneath the Longmenshan fault belt where the lower crust of the East Tibetan Plateau and the lithospheric mantle of the Yangze block are juxtaposed.

COUPLED NUMERICAL SIMULATION ON COLD ROLLER'S TEMPERATURE FIFLD-PHASE TRANSFORMATION - STRESS FIELD DURING ITS QUENCHING PSOCESS

Complicated changns occur inside the steel parts during quenching process. The abruptly changed boundary conditions make the temperature field,micro - structure and stress field change dramatically in very short time, and these variables take a contact interactions in the whole process. In this paper, a three dimensional non - linear mathematical model for queeching process has been founded and the numerical simulation on temperature field,microstructre and stress field has been realized.In the FEM analysis, the incremental iteration method is used to deal with such complicated nonlinear as boundary nonlinear, physical property nonlinear,transformation nonlinear etc.The effect of stress on transformation kinetics has been considered in the calculation of microstructure. In the stress field anal- ysis,a thermo- elasto - plastic model has been founded, which considers such factors as transforma- tion strain,transformation plastic strain, themal strain and the effect of temperature and transforma- tion on mechanical propertier etc. The transient temperature field, microstructure distribution and stress field of the roller on any time can be displayed vividly,and the cooling curve and the changes of stress on any position can also be given.

Effect of sensor quantity on measurement accuracy of log inner defects by using stress wave

Wood nondestructive testing （NDT） is one of the high efficient methods in utilizing wood. This paper explained the principle of log defect testing by using stress wave, and analyzed the effects of sensor quantity on defect testing results by using stress wave in terms of image fitting degree and error rate. The results showed that for logs with diameter ranging from 20 to 40 cm, at least 12 sensors were needed to meet the requirement which ensure a high testing accuracy of roughly 90% of fitness with 0.1 of error rate. And 10 sensors were recommended to judge the possible locations of defects and 6 sensors were sufficient to decide whether there were defects or not.

Simulation of Paleotectonic Stress Fields and Distribution Prediction of Tectonic Fractures at the Hudi Coal Mine, Qinshui Basin

Study on tectonic fractures based on the inversion of tectonic stress fields is an effective method. In this study, a geological model was set up based on geological data from the Hudi Coal Mine, Qinshui Basin, a mechanical model was established under the condition of rock mechanics and geostress, and the finite element method was used to simulate the paleotectonic stress field. Based on the Griffith and Mohr-Coulomb criterion, the distribution of tectonic fractures in the Shanxi Formation during the Indosinian, Yanshanian, and Himalayan period can be predicted with the index of comprehensive rupture rate. The results show that the acting force of the Pacific Plate and the India Plate to the North China Plate formed the direction of principal stress is N-S, NW - SE, and NE - SW, respectively, in different periods in the study area. Changes in the direction and strength of the acting force led to the regional gradients of tectonic stress magnitude, which resulted in an asymmetrical distribution state of the stress conditions in different periods. It is suggested that the low-stress areas are mainly located in the fault zones and extend along the direction of the fault zones. Furthermore, the high-stress areas are located in the junction of fold belts and the binding site of multiple folds. The development of tectonic fractures was affected by the distribution of stress intensity and the tectonic position of folds and faults, which resulted in some developed areas with level I and II. There are obvious differences in the development of tectonic fractures in the fold and fault zones and the anticline and syncline structure at the same fold zones. The tectonic fractures of the Shanxi Formation during the Himalayan period are more developed than those during the Indosinian and Yanshanian period due to the superposition of the late tectonic movement to the early tectonic movement and the differences in the magnitude and direction of stress intensity.

The Relationship between Fractures and Tectonic Stress Field in the Extra Low-Permeability Sandstone Reservoir at the South of Western Sichuan Depression

The formation and distribution of fractures are controlled by paleotectonic stress field, and their preservative status and effects on development are dominated by the modern stress field. Since Triassic, it has experienced four tectonic movements and developed four sets of tectonic fractures in the extra low-permeability sandstone reservoir at the south of western Sichuan depression. The strikes of fractures are in the S-N, NE-SW, E-W, and NW-SE directions respectively. At the end of Triassic, under the horizontal compression tectonic stress field, for which the maximum principal stress direction was NW.SE, the fractures were well developed near the S-N faults and at the end of NE-SW faults, because of their stress concentration. At the end of Cretaceous, in the horizontal compression stress fields of the NE-SW direction, the stress was obviously lower near the NE-SW faults, thus, fractures mainly developed near the S-N faults. At the end of Neogene-Early Pleistocene, under the horizontal compression tectonic stress fields of E-W direction, stress concentrated near the NE-SW faults and fractures developed at these places, especially at the end of the NE-SE faults, the cross positions of NE-SW, and S-N faults. Therefore, fractures developed mostly near S-N faults and NE-SW faults. At the cross positions of the above two sets of faults, the degree of development of the fractures was the highest. Under the modern stress field of the NW-SE direction, the NW-SE fractures were mainly the seepage ones with tensional state, the best connectivity, the widest aperture, the highest permeability, and the minimum opening pressure.

Stress field modeling of northwestern South China Sea since 5.3 Ma and its tectonic significance

Tectonically, the northwestern South China Sea （SCS） is located at the junction between three micro-plates, i.e., the Indochina, South China and Zhongsha-Xisha micro-plates, and involves three basins, i.e., the Yinggehai Basin, the Qiongdongnan Basin and Xisha Trough in the east, and the Zhongjiannan Basin in the south. Since the Pliocene （5.3 Ma）, the Yinggehai Basin has experienced repeated accelerating subsidence, high thermal fluid, and widely developing mud-rich overpressure chambers, abundant mud diapers and crust-mantle mixed CO2. While a large central canyon was developed in the Qiongdongnan Basin, new rift occurred in the Xisha ~rough. These characteristics demonstrate a single tectonic unit for the northwestern SCS, for which we have undertaken stress field modeling to understand its plate deformations and sedimen- tary responses. Our results demonstrate that an extension tectonic event occurred after 5.3 Ma in theYingge- hal-Qiongdongnan-Xisha trough area, which is characterized by thinner crust C〈16000 m）, half-graben or graben structural style and thicker sedimentary sequences （〉3 500 m）. A new rift system subsequently was developed in this area; this event was mainly driven by the combined effects of different movement veloc- ity and direction of the three micro-plates, and the far-field effect of the continental collision between the Indian Plate and the Tibetan Plateau, and subduction of the Pacific Plate underneath the Eurasian Plate.

Evolution characteristics of Quaternary tectonic stress field in the north and east margin of Qinghai-Xizang plateau

By inversion of fault slip data for Quaternary tectonic stress field and the analysis of crustal deformation after lateTeriary. we explaincd the evolution of crustal dynamic about the north and east margin of Qinghai-Xizang (Tibet)plateau since Miocenc. From middle or late Miocene to early Pleistocene, the tectonic stress field was featured by amaximum principal compression which was coming from the collision of india Plate continued to the boundaryof the plateau. and was basically of reverse faulting type. Since the late period of early Pleistocene, Pleistocene continuedto push northward and the compressional deformation of the plateau interior increased continuously, meanwhile,N W-SE extension appeared on the east side of the plateau. This formed a favorable condition for the interior block offoe plateau to slide towards east and southeast, causing the faults surrounding the plateau to change from thrust tostrike-slip. -The contemporary tectonic stress field was formed from the late period of early Pleistocene and continuedto present. The direction of maximum principal compressional stress rotated clockwise with respect to the previoustectonic stress held. the stress field was mainly of strike-slip type.

Epigenetic field defects in progression to cancer

A field defect is a field of pre-malignant tissue in which a new cancer is likely to arise. Field defects often appear to be histologically normal under the microscope. Recent research indicates that cells within a field defect characteristically have an increased frequency of epigenetic alterations and these may be fundamentally important as underlying factors in progression to cancer. However, understanding of epigenetic field defects is at an early stage, and the work of Katsurano et al published this year, is a key contribution to this field. One question examined by Katsurano et al was how early could the formation of an epigenetic field defect be de-tected in a mouse colitis model of tumorigenesis. They highlighted a number of measurable epigenetic altera-tions, detected very early in normal appearing tissue undergoing histologically invisible tumorigenesis. They also documented the increasing presence of the epigenetic alterations at successive times during progression to cancer. In this commentary, we offer a perspective on the changes they observed within a broader sequence of epigenetic events that occur in progressionto cancer. In particular, we highlight the likely central role of epigenetic deficiencies in DNA repair gene expression that arise during progression to cancer.

Three dimensional tectonic stress field in North China

According to the latest data of geological structure, geophysics, in-situ stress measurement and focal mechanism,3-D tectonic stress field model in North China is built and 3-D tectonic stress field pattern of North China aresimulated by finite element method. Then the overall characteristics and regional specific feature of North Chinaare studied. Finally, the influences of the valid dynamic boundary conditions of North China Block, active faultsand the inhomogeneity of crustal medium on tectonic stress field of North China are investigated.