Numerical Simulation of Sloshing with Large Deforming Free Surface by MPS-LES Method

Moving particle semi-implicit （MPS） method is a fully Lagrangian particle method which can easily solve problems with violent free surface. Although it has demonstrated its advantage in ocean engineering applications, it still has some defects to be improved. In this paper, MPS method is extended to the large eddy simulation （LES） by coupling with a sub-particle-scale （SPS） turbulence model. The SPS turbulence model turns into the Reynolds stress terms in the filtered momentum equation, and the Smagorinsky model is introduced to describe the Reynolds stress terms. Although MPS method has the advantage in the simulation of the free surface flow, a lot of non-free surface particles are treated as free surface particles in the original MPS model. In this paper, we use a new free surface tracing method and the key point is ＂neighbor particle＂. In this new method, the zone around each particle is divided into eight parts, and the particle will be treated as a free surface particle as long as there are no ＂neighbor particles＂ in any two parts of the zone. As the number density parameter judging method has a high efficiency for the free surface particles tracing, we combine it with the neighbor detected method. First, we select out the particles which may be mistreated with high probabilities by using the number density parameter judging method. And then we deal with these particles with the neighbor detected method. By doing this, the new mixed free surface tracing method can reduce the mistreatment problem efficiently. The serious pressure fluctuation is an obvious defect in MPS method, and therefore an area-time average technique is used in this paper to remove the pressure fluctuation with a quite good result. With these improvements, the modified MPS-LES method is applied to simulate liquid sloshing problems with large deforming free surface. Results show that the modified MPS-LES method can simulate the large deforming free surface easily. It can not only capture the large impact pressure accurately on rolling tank wall but also can generate all physical phenomena successfully. The good agreement between numerical and experimental results proves that the modified MPS-LES method is a good CFD methodology in free surface flow simulations.

Optimal Design of Deforming Regulation for Compact Continuous Rolling Mill with Balanced Load

If the draught of each mill stand is limited by forced bite condition for compact continuous mill,the rolling load difference between one mill stand and another is very big.If deforming regulation of relative load for each mill stand is approximate to the same,the productive capacity of compact continuous mill can be brought into full play,and also the safety running and the smooth rolling of mill can be ensured.

Deforming analysis of sheet metal based on stereo vision and coordinate grid

A new approach based on stereo vision technology is introduced to analyzesheet metal deformation. By measuring the deformed circle grids that are printed on the sheetsurface before forming, the strain distribution of the workpiece is obtained. The measurement andanalysis results can be used to verify numerical simulation results and guide production. To getgood accuracy, some new techniques are employed: camera calibration based on genetic algorithm,feature abstraction based on self-adaptive technology, image matching based on structure feature andcamera modeling pre-constrains, and parameter calculation based on curve and surface optimization.The experimental values show that the approach proposed is rational and practical, which can providebetter measurement accuracy with less time than the conventional method.

Microstructural evolution and tensile properties of low-carbon steel with martensitic microstructure during warm deforming and annealing

For preparing large-scale nano-grained and ultrafine-grained steel sheets by warm rolling and annealing, the effects of deforming temperature on both the flow stress and the microstructure evolution of 09MnNiD steel with lath martensitic microstructure were studied by warm-compression test and transmission electron microscopy （TEM） observation. Thereafter, the steel with the lath martensitic structure was multi-pass warm-rolled and then annealed. TEM results indicate that nano-grained and ultrafine-grained steel sheets are formed by warm rolling at 400℃ and annealing at 400-600℃. In comparison with the as-warm-rolled specimen, the tensile strength at room temperature changes a little when the rolled samples are annealed below 450℃, and the tensile strength is greatly lowered as the annealing temperature increases to above 550℃.

An Improved Coupled Level Set and Continuous Moment-of-Fluid Method for Simulating Multiphase Flows with Phase Change

An improved algorithm for computing multiphase flows is presented in which the multimaterial Moment-of-Fluid(MOF)algorithm for multiphase flows,initially described by Li et al.(2015),is enhanced addressing existing MOF difficulties in computing solutions to problems in which surface tension forces are crucial for understanding salient flow mechanisms.The Continuous MOF(CMOF)method is motivated in this article.The CMOF reconstruction method inherently removes the"checkerboard instability"that persists when using the MOF method on surface tension driven multiphase(multimaterial)flows.The CMOF reconstruction algorithm is accelerated by coupling the CMOF method to the level set method and coupling the CMOF method to a decision tree machine learning(ML)algorithm.Multiphase flow examples are shown in the two-dimensional(2D),three-dimensional(3D)axisymmetric"RZ",and 3D coordinate systems.Examples include two material and three material multiphase flows:bubble formation,the impingement of a liquid jet on a gas bubble in a cryogenic fuel tank,freezing,and liquid lens dynamics.

7075铝合金切削加工晶粒尺寸演化过程研究

金属材料在切削加工过程中,表层晶粒在机械载荷和热载荷的剧烈冲击作用下快速再结晶使表面形成晶粒细化层,该细化层严重影响材料使役性能。在研究切削加工晶粒尺寸演化机制的基础上,通过DEFORM仿真软件实现7075铝合金晶粒尺寸演化过程,开展单因素法试验,构建了晶粒尺寸关于切削速度、进给量的预测模型。结果表明:切削速度增加,表层晶粒尺寸增大,细化层厚度减小;进给量增加,晶粒尺寸和细化层厚度在温度和塑性变形共同作用下先增加后减小。通过实验验证,该模型能够较为准确地预测材料表面晶粒尺寸。

9Cr3W3Co耐热钢锻造工艺数值模拟及实验研究

通过Deform 3D模拟了9Cr3W3Co耐热钢连续多道次锻造工艺,分析了等效应力、等效应变场和温度场的分布规律。基于模拟结果,优化了锻造工艺,并通过Gleeble-3800热模拟试验机对9Cr3W3Co耐热钢进行不同变形参数多道次热压缩实验,分析了不同变形参数下的热变形行为,结合热模拟真应力-真应变曲线和显微组织,验证了模拟的准确性。结果表明,模拟后的优化锻造工艺为应变速率5 s^(-1),变形方式为先大变形后小变形,变形后的坯料心部温度分布均匀,为951~970℃,等效应变分布均匀,为2.15~2.19。当应变速率为5 s^(-1)时,动态再结晶晶粒尺寸随变形温度的升高而变大,采用先大压下量后小压下量的方式,可获得完全再结晶的等轴晶,平均晶粒尺寸为15μm,变形后组织均匀性更好。结合微观组织演变结果分析,模拟实验具有可行性,实验结果与模拟结果基本吻合。

基于改进Deformable DETR的无人机视频流车辆目标检测算法

针对无人机视频流检测中小目标数量多、因图像传输质量较低而导致的上下文语义信息不充分、传统算法融合特征推理速度慢、数据集类别样本不均衡导致的训练效果差等问题,提出一种基于改进Deformable DETR的无人机视频流车辆目标检测算法。在模型结构方面,该算法设计了跨尺度特征融合模块以增大感受野,提升小目标检测能力,并采用针对object_query的挤压-激励模块提升关键目标的响应值,减少重要目标的漏检与错检率;在数据处理方面,使用了在线困难样本挖掘技术,改善数据集中类别样本分布不均的问题。在UAVDT数据集上进行了实验,实验结果表明,改进后的算法相较于基线算法在平均检测精度上提升了1.5%,在小目标检测精度上提升了0.8%,并在保持参数量较少增长的情况下,维持了原有的检测速度。

Deformable Catalytic Material Derived from Mechanical Flexibility for Hydrogen Evolution Reaction

Deformable catalytic material with excellent flexible structure is a new type of catalyst that has been applied in various chemical reactions,especially electrocatalytic hydrogen evolution reaction(HER).In recent years,deformable catalysts for HER have made great progress and would become a research hotspot.The catalytic activities of deformable catalysts could be adjustable by the strain engineering and surface reconfiguration.The surface curvature of flexible catalytic materials is closely related to the electrocatalytic HER properties.Here,firstly,we systematically summarized self-adaptive catalytic performance of deformable catalysts and various micro–nanostructures evolution in catalytic HER process.Secondly,a series of strategies to design highly active catalysts based on the mechanical flexibility of lowdimensional nanomaterials were summarized.Last but not least,we presented the challenges and prospects of the study of flexible and deformable micro–nanostructures of electrocatalysts,which would further deepen the understanding of catalytic mechanisms of deformable HER catalyst.

Rapid report of the December 18,2023 M_(S)6.2 Jishishan earthquake,Gansu,China

On December 18,2023,the Jishishan area in Gansu Province was jolted by a M_(S) 6.2 earthquake,which is the most powerful seismic event that occurred throughout the year in China.The earthquake occurred along the NWtrending Lajishan fault(LJSF),a large tectonic transformation zone.After this event,China Earthquake Networks Center(CENC)has timely published several reports about seismic sources for emergency responses.The earthquake early warning system issued the first alert 4.9 s after the earthquake occurrence,providing prompt notification that effectively mitigated panics,injuries,and deaths of residents.The near real-time focal mechanism solution indicates that this earthquake is associated with a thrust fault.The distribution of aftershocks,the rupture process,and the recorded amplitudes from seismic monitoring and GNSS stations,all suggest that the mainshock rupture predominately propagates to the northwest direction.The duration of the rupture process is~12 s,and the largest slip is located at approximately 6.3 km to the NNW from the epicenter,with a peak slip of 0.12 m at~8 km depth.Seismic station N0028 recorded the highest instrumental intensity,which is 9.4 on the Mercalli scale.The estimated intensity map shows a seismic intensity reaching up to IX near the rupture area,consistent with field survey results.The aftershocks(up to December 22,2023)are mostly distributed in the northwest direction within~20 km of the epicenter.This earthquake caused serious casualties and house collapses,which requires further investigations into the impact of this earthquake.

Mechanical Modeling and Analysis of Stability Deterioration of Production Well During Marine Hydrate Depressurization Production

Different from oil and gas production,hydrate reservoirs are shallow and unconsolidated,whose mechanical properties deteriorate with hydrate decomposition.Therefore,the formations will undergo significant subsidence during depressurization,which will destroy the original force state of the production well.However,existing research on the stability of oil and gas production wells assumes the formation to be stable,and lacks consideration of the force exerted on the hydrate production well by formation subsidence caused by hydrate decomposition during production.To fill this gap,this paper proposes an analytical method for the dynamic evolution of the stability of hydrate production well considering the effects of hydrate decomposition.Based on the mechanical model of the production well,the basis for stability analysis has been proposed.A multi-field coupling model of the force state of the production well considering the effect of hydrate decomposition and formation subsidence is established,and a solver is developed.The analytical approach is verified by its good agreement with the results from the numerical method.A case study found that the decomposition of hydrate will increase the pulling-down force and reduce the supporting force,which is the main reason for the stability deterioration.The higher the initial hydrate saturation,the larger the reservoir thickness,and the lower the production pressure,the worse the stability or even instability.This work can provide a theoretical reference for the stability maintaining of the production well.

Anomalous{1012}tensile twinning and subsequent detwinning in a friction stir processed carbon fiber-reinforced Mg composite

1.Main text Owing to their low density and high specific strength,magnesium alloys and magnesium-based composites have great potential as structure metal materials in applications where lightweight matters[1–4].Deformation twins[5],especially the{1012}tension twins(also called tensile or extension twins)with a low critical resolved shear stress(CRSS)[6],are commonly observed in Mg alloys.They can provide the much-needed deformation along the c-axis in their hcp structure resulting from the very few easily activated slip systems in this crystal structure[7].The tensile twinning activation usually follows the macroscopic Schmid factor law[2],i.e.,the twin variant with the highest Schmid factor occurs,and it only appears when its Schmid factor is positive.

The application of the strip-shaped cymba conchae orthosis in the nonsurgical correction of complex auricular deformity

Objective: This study aims to evaluate the efficacy and safety of using a strip-shaped cymba conchae orthosis for the nonsurgical correction of complex auricular deformities. Methods: Clinical data were collected from 2020 to 2021 for 6 patients who underwent correction using a stripshaped cymba conchae orthosis. The indications, corrective effects, and complications associated with use of the orthosis were analyzed. Results: There were four indications for treatment: cryptotia with helix adhesion;cryptotia with grade I microtia;cryptotia with excessive helix thickness;and auricular deformity beyond the treatment time window(≥6 months). Excellent corrective effects were observed in all 6 patients. Complications occurred in one patient, who recovered after symptomatic treatment. Conclusion: The use of a strip-shaped cymba conchae orthosis alone or combined with a U-shaped helix orthosis presents a feasible approach for correcting complex auricular deformities or deformities beyond the treatment time window in pediatric patients.

Application of GNSS-PPP on Dynamic Deformation Monitoring of Offshore Platforms

The real-time dynamic deformation monitoring of offshore platforms under environmental excitation is crucial to their safe operation.Although Global Navigation Satellite System-Precise Point Positioning(GNSS-PPP)has been considered for this purpose,its monitoring accuracy is relatively low.Moreover,the influence of background noise on the dynamic monitoring accuracy of GNSS-PPP remains unclear.Hence,it is imperative to further validate the feasibility of GNSS-PPP for deformation monitoring of offshore platforms.To address these concerns,vibration table tests with different amplitudes and frequencies are conducted.The results demonstrate that GNSS-PPP can effectively monitor horizontal vibration displacement as low as±30 mm,which is consistent with GNSS-RTK.Furthermore,the spectral characteristic of background noise in GNSS-PPP is similar to that of GNSS-RTK(Real Time Kinematic).Building on this observation,an improved Complete Ensemble Empirical Mode Decomposition with Adaptive Noise(CEEMDAN)has been proposed to de-noise the data and enhance the dynamic monitoring accuracy of GNSS-PPP.Field monitoring application research is also undertaken,successfully extracting and analyzing the dynamic deformation of an offshore platform structure under environmental excitation using GNSS-PPP monitoring in conjunction with improved CEEMDAN de-noising.By comparing the de-noised dynamic deformation trajectories of the offshore platform during different periods,it is observed that the platform exhibits reversible alternating vibration responses under environmental excitation,with more pronounced displacement deformation in the direction of load action.The research results confirm the feasibility and potential of GNSS-PPP for dynamic deformation monitoring of offshore platforms.

Origin of nucleation and growth of extension twins in grains unsuitably oriented for twinning during deformation of Mg-1%Al

A large number of anomalous extension twins,with low or even negative twinning Schmid factors,were found to nucleate and grow in a strongly textured Mg-1Al alloy during tensile deformation along the extruded direction.The deformation mechanisms responsible for this behaviour were investigated through in-situ electron back-scattered diffraction,grain reference orientation deviation,and slip trace-modified lattice rotation.It was found that anomalous extension twins nucleated mainly at the onset of plastic deformation at or near grain boundary triple junctions.They were associated with the severe strain incompatibility between neighbour grains as a result from the differentbasal slip-induced lattice rotations.Moreover,the anomalous twins were able to grow with the applied strain due to the continuous activation ofbasal slip in different neighbour grains,which enhanced the strain incompatibility.These results reveal the complexity of the deformation mechanisms in Mg alloys at the local level when deformed along hard orientations.

1Cr16Co5Ni2MoWVNbN耐热钢球座模锻成型工艺模拟与试验验证

通过热压缩模拟实验研究了1Cr16Co5Ni2MoWVNbN耐热钢在热变形过程中的动态再结晶行为,通过Deform 3D有限元数值模拟研究了应变速率和坯料尺寸对1Cr16Co5Ni2MoWVNbN耐热钢球座模锻成型工艺的影响。热压缩试验结果表明,1Cr16Co5Ni2MoWVNbN耐热钢发生动态再结晶、混晶现象不明显的临界变形量约为20%,增大应变速率有利于在小变形量下,获得更加均匀的组织。数值模拟结果表明,随着应变速率提高,模锻件最小变形区域的等效应变与等效应力均增加,随着坯料直径增加,模锻件最小变形区的等效应变下降,等效应力先降低后提高。应变速率为0.1 s^(-1)时,坯料直径ϕ60 mm~ϕ65 mm,最小变形区域工程应变可达到20%以上,且具有较好的锻造成型性。根据数值模拟结果,设计了直径ϕ60 mm、高度74 mm的坯料,以0.1 s^(-1)的应变速率进行模锻验证试验,试制出的锻件成型好、组织与硬度均匀,验证了数值模拟结果的合理与可行性。

Flow characteristics and hot workability of a typical low-alloy high-strength steel during multi-pass deformation

Heavy components of low-alloy high-strength(LAHS) steels are generally formed by multi-pass forging. It is necessary to explore the flow characteristics and hot workability of LAHS steels during the multi-pass forging process, which is beneficial to the formulation of actual processing parameters. In the study, the multi-pass hot compression experiments of a typical LAHS steel are carried out at a wide range of deformation temperatures and strain rates. It is found that the work hardening rate of the experimental material depends on deformation parameters and deformation passes, which is ascribed to the impacts of static and dynamic softening behaviors. A new model is established to describe the flow characteristics at various deformation passes. Compared to the classical Arrhenius model and modified Zerilli and Armstrong model, the newly proposed model shows higher prediction accuracy with a confidence level of 0.98565. Furthermore, the connection between power dissipation efficiency(PDE) and deformation parameters is revealed by analyzing the microstructures. The PDE cannot be utilized to reflect the efficiency of energy dissipation for microstructure evolution during the entire deformation process, but only to assess the efficiency of energy dissipation for microstructure evolution in a specific deformation parameter state.As a result, an integrated processing map is proposed to better study the hot workability of the LAHS steel, which considers the effects of instability factor(IF), PDE, and distribution and size of grains. The optimized processing parameters for the multi-pass deformation process are the deformation parameters of 1223–1318 K and 0.01–0.08 s^(-1). Complete dynamic recrystallization occurs within the optimized processing parameters with an average grain size of 18.36–42.3 μm. This study will guide the optimization of the forging process of heavy components.

Prediction of subsurface settlement induced by shield tunnelling in sandy cobble stratum

This study focuses on the analytical prediction of subsurface settlement induced by shield tunnelling in sandy cobble stratum considering the volumetric deformation modes of the soil above the tunnel crown.A series of numerical analyses is performed to examine the effects of cover depth ratio(C/D),tunnel volume loss rate(h t)and volumetric block proportion(VBP)on the characteristics of subsurface settle-ment trough and soil volume loss.Considering the ground loss variation with depth,three modes are deduced from the volumetric deformation responses of the soil above the tunnel crown.Then,analytical solutions to predict subsurface settlement for each mode are presented using stochastic medium theory.The influences of C/D,h t and VBP on the key parameters(i.e.B and N)in the analytical expressions are discussed to determine the fitting formulae of B and N.Finally,the proposed analytical solutions are validated by the comparisons with the results of model test and numerical simulation.Results show that the fitting formulae provide a convenient and reliable way to evaluate the key parameters.Besides,the analytical solutions are reasonable and available in predicting the subsurface settlement induced by shield tunnelling in sandy cobble stratum.

Liquefaction susceptibility and deformation characteristics of saturated coral sandy soils subjected to cyclic loadings-a critical review

Coral sandy soils widely exist in coral island reefs and seashores in tropical and subtropical regions.Due to the unique marine depositional environment of coral sandy soils,the engineering characteristics and responses of these soils subjected to monotonic and cyclic loadings have been a subject of intense interest among the geotechnical and earthquake engineering communities.This paper critically reviews the progress of experimental investigations on the undrained behavior of coral sandy soils under monotonic and cyclic loadings over the last three decades.The focus of coverage includes the contractive-dilative behavior,the pattern of excess pore-water pressure(EPWP)generation and the liquefaction mechanism and liquefaction resistance,the small-strain shear modulus and strain-dependent shear modulus and damping,the cyclic softening feature,and the anisotropic characteristics of undrained responses of saturated coral sandy soils.In particular,the advances made in the past decades are reviewed from the following aspects:(1)the characterization of factors that impact the mechanism and patterns of EPWP build-up;(2)the identification of liquefaction triggering in terms of the apparent viscosity and the average flow coefficient;(3)the establishment of the invariable form of strain-based,stress-based,or energy-based EPWP ratio formulas and the unique relationship between the new proxy of liquefaction resistance and the number of cycles required to reach liquefaction;(4)the establishment of the invariable form of the predictive formulas of small strain modulus and strain-dependent shear modulus;and(5)the investigation on the effects of stress-induced anisotropy on liquefaction susceptibility and dynamic deformation characteristics.Insights gained through the critical review of these advances in the past decades offer a perspective for future research to further resolve the fundamental issues concerning the liquefaction mechanism and responses of coral sandy sites subjected to cyclic loadings associated with seismic events in marine environments.

Material point method simulation of hydro-mechanical behaviour in twophase porous geomaterials: A state-of-the-art review

The material point method(MPM)has been gaining increasing popularity as an appropriate approach to the solution of coupled hydro-mechanical problems involving large deformation.In this paper,we survey the current state-of-the-art in the MPM simulation of hydro-mechanical behaviour in two-phase porous geomaterials.The review covers the recent advances and developments in the MPM and their extensions to capture the coupled hydro-mechanical problems involving large deformations.The focus of this review is aiming at providing a clear picture of what has or has not been developed or implemented for simulating two-phase coupled large deformation problems,which will provide some direct reference for both practitioners and researchers.