Study the Structural, Electronic, Optical Properties of CZTS Compound after Doping Ba at Zn Site and Si at Sn Site Using Density Functional Theory (DFT)

The structural, electronic, and optical properties of Cu2Zn1−xBaxSn1−ySiyS4 compounds have been calculated using GGA-PBE function within the framework of Density Functional Theory (DFT). In the present work, lattice parameters remained the same, that is tetragonal crystal structure for 0% and 100% doping concentration. The electronic band gap of Cu2Zn1−xBaxSn1−ySiyS4 compounds has been gradually increased for continuous increment of doping concentration where the highest electronic band gap is 1.117 eV for Cu2BaSiS4 structure. Moreover, the band gap changes from direct to indirect band gap with the increase of doping concentration in the parent compound. The absorption coefficient has been found to be high (> 104 cm−1) in UV-region for all the doping concentration which makes the studied compound as a potential candidate of absorber layer in the UV detector. The theoretical study of the effect of double doping in the CZTS compound is very interesting for improving the quality of it and it would be a reference for the theoretical and experimental researchers.

Understanding the Relativistic Generalization of Density Functional Theory (DFT) and Completing It in Practice

In 2014, 50 years following the introduction of density functional theory (DFT), a rigorous understanding of it was published [AIP Advances, 4, 127,104 (2014)]. This understanding includes two features that complete the theory in practice, inasmuch as they are necessary for its correct application in electronic structure calculations;this understanding elucidates what appears to have been the crucial misunderstanding for 50 years, namely, the confusion between a stationary solution, attainable with most basis sets, following self-consistent iterations, with the ground state solution. The latter is obtained by a calculation that employs the well-defined optimal basis set for the system. The aim of this work is to review the above understanding and to extend it to the relativistic generalization of density functional theory by Rajagopal and Callaway [Phys. Rev. B7, 1912 (1973)]. This extension straightforwardly follows similar steps taken in the non-relativistic case, with the four-component current density, in the former, replacing the electronic charge density, in the latter. This new understanding, which completes relativistic DFT in practice, is expected to be needed for the study of heavy atoms and of materials (from molecules to solids) containing them—as is the case for some high temperature superconductors.

A Periodic Density Functional Study on Adsorption Properties of Methoxy on Au(111) Surface

Adsorption of CH3O at four sites （top, bridge, hcp, fcc） on Au（111） surface has been investigated by density functional theory method at the generalized gradient approximation level. We have performed calculations on adsorption energies, structures, Mulliken charges and vibrational frequencies of CH3O on Au（111） surface with full-geometry optimization. The predicted results are compared with the available experimental observation. The calculated CH3O adsorption structure and stretching vibrational frequencies agree well with experimental ones, and precise determinations of adsorption sites are carded out. The most favorite adsorption on Au（111） occurs at the bridge site, and O-C axis is tilted to the surface. However, on hollow sites （hcp, fcc） the species is adsorbed in an upright geometry （pseudo-C3v local symmetry）.

Interaction of Photoactive[Fe(CN)_6]^(4-) with TiO_2 Anatase(101) Surface:A Periodic Density Functional Theory Study

The plane-wave pseudopotential function method, based on density-functional theory, has been used to calculate the adsorption, electronic band structures, orbitals and optical absorption spectrum of [Fe（CN）6]^4- on TiOz anatase（101） surface. Our calculations reveal that the surface-modified anatase system has large adsorption energy and a much narrower band gap. [Fe（CN）6]^4- adsorption on the （101） surface could lead to a large red shift of the anatase optical absorption threshold, which extends into a visible region significantly. The calculated results are in agreement with the experiment and other theoretical studies reasonably. It is very important for the understanding and further development ofphotovoltaic materials that are active under visible light.

Studies of n-Octanol/water Partition Coefficients (lgK_(ow)) for Organophosphate Compounds by Density Functional Theory

Optimized calculation of 35 dialkyl phenyl phosphate compounds （OPs） was carded out at the B3LYP/6-31G^＊ level in Gaussian 98 program. Based on the theoretical linear solvation energy relationship （TLSER） model, the obtained parameters were taken as theoretical descriptors to establish the novel QSPR model for predicting n-octanol/water partition coefficients （lgKow） of OPs. The new model achieved in this work contains three variables, i.e., molecular volume （Vm）, dipole moment of the molecules （μ） and enthalpy （H^0）. For this model, R^2 = 0.9167 and SD = 0.31 at large t values. In addition, the variation inflation factors （VIF） of variables are all close to 1.0, suggesting high accuracy of the predicting model. And the results of cross-validation test （q^2 = 0.8993） and method validation also showed the model of this study exhibited optimum stability and better predictive power than that from semi-empirical method. The model achieved can be used to predict IgKow of congeneric compounds.

Hydrogen storage in BC_3 composite single-walled nanotube:a combined density functional theory and Monte Carlo investigation

This paper applies a density functional theory （DFT） and grand canonical Monte Carlo simulations （GCMC） to investigate the physisorptions of molecular hydrogen in single-walled BC3 nanotubes and carbon nanotubes. The DFT calculations may provide useful information about the nature of hydrogen adsorption and physisorption energies in selected adsorption sites of these two nanotubes. Furthermore, the GCMC simulations can reproduce their storage capacity by calculating the weight percentage of the adsorbed molecular hydrogen under different conditions. The present results have shown that with both computational methods, the hydrogen storage capacity of BC3 nanotubes is superior to that of carbon nanotubes. The reasons causing different behaviour of hydrogen storage in these two nanotubes are explained by using their contour plots of electron density and charge-density difference.

Studies of Structural and Thermodynamic Properties for Polychlorinated Thianthrenes by Density Functional Theory

The structural and thermodynamic （PCTAs） in the ideal gas state at 298.15 K and 1.013 properties of 75 polychlorinated thianthrenes ×10^5 Pa have been calculated at the B3LYP/6- 31G＊ level using Gaussian 98 program. Based on the output data of Gaussian, the isodesmic reactions were designed to calculate standard enthalpy of formation （△fH^θ） and standard free energy of formation （△fH^θ） of PCTAs congeners. The relations of these thermodynamic parameters with the number and position of C1 atom substitution （Npcs） were discussed, and it was found that there exists high correlation between thermodynamic parameters （total energy （TE）, zero-point vibrational energy （ZPE）, thermal correction to energy （Eth）, heat capacity at constant volume （Cv^θ）, entropy （S^θ）, enthalpy （H^θ）, free energy （G^θ）, standard enthalpies of formation （△fH^θ） and standard Gibbs energies of formation （△fG^θ）） and Npcs. On the basis of the relative magnitude of their △fG^θ, the order of relative stability of PCTA congeners was theoretically proposed. In addition, the correlations between structural parameters and Npcs were also discussed. The good correlations were found between molecular average polarizability （α）, energy of the highest occupied molecular orbital （EHOMO）, molecular volume （Vm） and Npcs, and all R^2 values are larger than 0.95. Moreover, it was supposed that the isomer groups with higher toxicity should be Tri-CTA and TCTA.

New ternary superconducting compound LaRu2As2： Physical properties from density functional theory calculations

In this paper, we perform the density functional theory （DFT） -based calculations by the first-principles pseudopo- tential method to investigate the physical properties of the newly discovered superconductor LaRu2As2 for the first time. The optimized structural parameters are in good agreement with the experimental results. The calculated independent elas- tic constants ensure the mechanical stability of the compound. The calculated Cauchy pressure, Pugh＇s ratio as well as Poisson＇s ratio indicate that LaRu2As2 should behave as a ductile material. Due to low Debye temperature, LaRu2As2 may be used as a thermal barrier coating （TBC） material. The new compound should exhibit metallic nature as its valence bands overlap considerably with the conduction bands. LaRu2As2 is expected to be a soft material and easily machinable because of its low hardness value of 6.8 GPa. The multi-band nature is observed in the calculated Fermi surface. A highly anisotropic combination of ionic, covalent and metallic interactions is expected to be in accordance with charge density calculation.

Tuning electronic properties of the S2/graphene heterojunction by strains from density functional theory

Based on the density functional calculations, the structural and electronic properties of the WS2/graphene heterojunction under different strains are investigated. The calculated results show that unlike the free mono-layer WS2, the monolayer WS2 in the equilibrium WS2/graphene heterojunctionis characterized by indirect band gap due to the weak van der Waals interaction. The height of the schottky barrier for the WS2/graphene heterojunction is 0.13 eV, which is lower than the conventional metal/MoS2 contact. Moreover, the band properties and height of schottky barrier for WS2/graphene heterojunction can be tuned by strain. It is found that the height of the schottky barrier can be tuned to be near zero under an in-plane compressive strain, and the band gap of the WS2 in the heterojunction is turned into a direct band gap from the indirect band gap with the increasing schottky barrier height under an in-plane tensile strain. Our calculation results may provide a potential guidance for designing and fabricating the WS2-based field effect transistors.

Theoretical Study on a 42 T Model of Beta Zeolite by Density Functional Theory Simulation

Density functional theory was applied to study the structure of Beta zeolite. A model cluster containing 41Si atoms, 1 Al atom, 70 O atoms and 29 H atoms was constructed. The model structures were optimized using the Becke＇s three-parameter hybrid method with the Lee-Yang-Parr correlation functional （B3LYP） and the 6-31G basis set applying the Gaussian03 program package. The NMR parameters were calculated to validate the rationality of the model. It was found that in the optimization models, all O-H bond lengths were in range of 0.984-0.985A^°, among which the model with O-H bond length of 0.98478A^° was more stable than the others. The ^1H and ^27Al chemical shifts of the most stable model were 4.03434 and 55.74 ppm, which were pretty consistent with Larry＇ s experimental data of 4.1 and 54 ppm. The relationship between other structure parameters and total relative electric energy has also been found. All the results exhibit that the 42 T （the total number of Si and Al atoms is 42） model has common properties of the standard of zeolite Beta.

A Density Functional Study of N-Doped TiO_2 Anatase Cluster

A systematic study on geometry, electronic structure and vibrational properties of N-doped TiO2 anatase cluster, within the framework of the density functional theory, has been performed in this work. The calculations confirmed that the most structures in substitutional model consist of a two-coordinate bridge structure and a three-coordinate hollow structure. The calculated results can well explain the red shift in N-doped TiO2 observed in experiments. The study provides an illustration for the N-doped anatase from the viewpoint of chemical bonding theory.

Estimation of n-Octanol/water Partition Coeffi-cients(lgK_(ow)) and the Aqueous Solubility(-lg_(Sw)) of all PCDF Congeners by Density Functional Theory

Optimized calculation of dibenzofuran （DF） and 135 polychlorinated dibenzofurans （PCDFs） was carried out at the B3LYP/6-31G＊ level in GAUSSIAN 98 program. Based on the theoretical linear solvation energy relationship （TLSER） model, the obtained structural parameters were taken as theoretical descriptors to establish the novel quantitative structureproperty relationship （QSPR） model for predicting n-octanol/water partition coefficients （lgKow） of PCDFs. The new model of lgKow achieved in this work contains three variables： energy of the highest occupied molecular orbital （EHOMO）, the most negative atomic partial charge （q^-） and average molecular polarizability （a）, of which R^2= 0.9011 and SD = 0,17 with larger t values. In addition, the variation inflation factors （VIF） of variables in the present model are all less than 5.5, suggesting high accuracy of the lgKow model. And the results of cross-validation test （q^2 = 0.8688） and method validation also show this model exhibits optimum stability and better predictive power than semi-empirical method. At the same time, it is found that the aqueous solubility （-lgSw） has high relative correlation with constant volume molar heat capacity （Cv^0）, of which R^2 = 0.9777 and SD = 0.22. Moreover, lgKow and -lgSw values of all PCDF congeners were predicted respectively.

Direct atomic-level insight into oxygen reduction reaction on size-dependent Pt-based electrocatalysts from density functional theory calculations

Developing novel oxygen reduction reaction(ORR)catalysts with high activity is urgent for proton exchange membrane fuel cells.Herein,we investigated a group of size-dependent Pt-based catalysts as promising ORR catalysts by density functional theory calculations,ranging from single-atom,nanocluster to bulk Pt catalysts.The results showed that the ORR overpotential of these Pt-based catalysts increased when its size enlarged to the nanoparticle scale or reduced to the single-atom scale,and the Pt_(38)cluster had the lowest ORR overpotential(0.46 V)compared with that of Pt_(111)(0.57 V)and single atom Pt(0.7 V).Moreover,we established a volcano curve relationship between the ORR overpotential and binding energy of O*(ΔE_(O*),confirming the intermediate species anchored on Pt38cluster with suitable binding energy located at top of volcano curve.The interaction between intermediate species and Pt-based catalysts were also investigated by the charge distribution and projected density of state and which further confirmed the results of volcano curve.

Pressure-dependent physical properties of cubic SrΒO3(Β=Cr,Fe)perovskites investigated by density functional theory

We perform the first-principles investigations of the structural,elastic,electronic,and optical properties of SrBO3(B=Cr,Fe)perovskites under pressure based on density functional theory(DFT).This is the first detailed pressure-dependent study of the physical properties for these compounds.The calculated structural parameters are consistent with the existing experimental results and slightly decrease with the application of pressure.The mechanical properties are discussed in detail and reveal that the SrCrO3 is harder than SrFeO3.Without pressure,these compounds behave like half-metals,confirmed by their band structure and density of states.Although the SrCrO3 retains its half-metallic nature under pressure,SrFeO3 becomes metallic for both up-spin and down-spin configuration.Both charge density and bond overlap population reveal the covalent nature of Cr–O bond and Fe–O bond in the studied compounds.The optical properties of SrBO3,also discussed for the first time,reveal some interesting results.

Density functional study for structure and electronic properties of FeS_2(100)

The electronic properties of FeS 2 (100) surface were studied by using a density functional theory(DFT) method. The very stable (100) surface does not give any significant geometric relaxation and can be regarded as a simple termination of the bulk structure along a plane of cleaved Fe S bonds. The electronic structure of FeS 2 (100) surface is characterized by surface states in its forbidden zone. The highest occupied and the lowest unoccupied states localize at surface Fe sites. Fe sites are energetically favored over S 2 sites for redox interaction with electron donor or acceptor species on (100) surface.

Theoretical Study on the Optical Properties for 2,7- and 3,6-Linked Carbazole Trimers by Time-dependent Density Functional Theory

Electronic properties, such as HOMO and LUMO energies, band gaps, ionization potential （IP） and electron affinity （EA） of 2,7- and 3,6-1inked carbazole trimers, two conjugated oligomcrs with different linkages of carbazole, were studicd by the density functional theory with Becke-Lee-Young-Parr composite exchange correlation functional （B3LYP）. The absorption spectra of these compounds were also investigated by time-dependent density functional theory （TD-DFT） with 6-3 IG＊ basis set. The calculated results indicated that the HOMO and LUMO of the 2,7- and 3,6-1inked carbazole trimers are both slightly destabilized on going from methyl substitution to sec-butyl substitution. Both IP and EA exhibit their good hole-transporting but poor electronaccepting ability. The presence of alkyl groups on the nitrogen atoms does not affect the intra-chain electronic delocalization along the molecular frame. Thus no significant effect on the band gap and absorption spectra of compounds has been found.

Investigation of Structural and Electronic Properties of [Tris(Benzene-1,2-Dithiolato)M]^3-(M = V, Cr, Mn, Fe and Co) Complexes: A Spectroscopic and Density Functional Theoretical Study

In this study, the first raw transition metals from V to Co complexes with benzene-1,2-dithiolate (L2-) ligand have been studied theoretically to elucidate the geometry, electronic structure and spectroscopic properties of the complexes. Density Functional Theory (DFT) and Time-Dependent Density Functional Theory (TD-DFT) methods have been used. The ground state geometries, binding energies, spectral properties (UV-vis), frontier molecular orbitals (FMOs) analysis, charge analysis and natural bond orbital (NBO) have been investigated. The geometrical parameters are in good agreement with the available experimental data. The metal-ligand binding energies are 1 order of magnitude larger than the physisorption energy of a benzene-1, 2-dthiolate molecule on a metallic surface. The electronic structures of the first raw transition metal series from V to Co have been elucidated by UV-vis spectroscopic using DFT calculations. In accordance with experiment the calculated electronic spectra of these tris complexes show bands at 522, 565, 559, 546 and 863 nm for V3+, Cr3+, Mn3+, Fe3+ and Co3+ respectively which are mainly attributed to ligand to metal charge transfer (LMCT) transitions. The electronic properties analysis shows that the highest occupied molecular orbital (HOMO) is mainly centered on metal coordinated sulfur atoms whereas the lowest unoccupied molecular orbital (LUMO) is mainly located on the metal surface. From calculation of intramolecular interactions and electron delocalization by natural bond orbital (NBO) analysis, the stability of the complexes was estimated. The NBO results showed significant charge transfer from sulfur to central metal ions in the complexes, as well as to the benzene. The calculated charges on metal ions are also reported at various charge schemes. The calculations show encouraging agreement with the available experimental data.

SO_(2)对K2CO_(3)吸附CO_(2)性能影响的实验及DFT机理研究

电站锅炉的尾气在脱硫后含有微量的SO_(2),导致CO_(2)吸附剂性能变差。根据电厂烟气的组分,采用模拟烟气在实验室条件下对K2CO_(3)吸附剂的CO_(2)吸附性能及SO_(2)对CO_(2)吸附的影响进行实验研究。结合XRD分析,利用密度泛函理论(density functional theory,DFT)对SO_(2)在K2CO_(3)吸附剂上的影响及CO_(2)吸附机理进行理论研究。结果表明,受SO_(2)分子S原子活跃的s轨道影响,S的p轨道及O原子活性均增强,与K2CO_(3)表面O原子价带顶能带简并,SO_(2)被优先吸附在K2CO_(3)表面的O顶位,并将CO_(2)推离吸附剂表面,导致吸附剂活性位点虽有空余却无法吸附CO_(2)。在实验中表现为:模拟烟气中CO_(2)体积浓度为10%时,气氛中体积浓度为0.007%的SO_(2)会使吸附剂的吸附量由1.65 mmol/g降低至1.01 mmol/g。提出CO_(2)与H2O在K2CO_(3)(001)表面的吸附机理,理论计算的反应活化能为40.7 kJ/mol,反应热为-54.9 kJ/mol。

Density Function Theory Studies on the Structure of AMT Inhibitor

Density function theory （DFT） at the B3LYP/6- 311 ＋ ＋ G（2d） （5D, 7F） level of theory was calculated to predict the geometry structures, toted energy and net charges of four kinds of dynamic isomer molecules of 2-aminino-5 mercapto- 1,3,4-thiodizole （ AA/IT for short）. The fact that the atoms in four kinds of dynamie AMT isomer molecules lie in a plane and one kind of AMT is most stable is approved. The results also indicate that the pentogon ring in four kinds of dynamic AMT isomer molecules are aromatics, and the AMTc and Cu corrosion mitigation film produces as a result of the bonds form one by one of the covalent bond of Cu（1） with 7 N atom in AMTc amd the coordinate bond of Cu with 2S atom in ATMc. The resonant vibration frequencies and IR intensity for the four kituds of dynamic isomer of AMT are also calculated and their IR spectra are shown.

Quantum spin Hall insulators in chemically functionalized As(110)and Sb(110)films

We propose a new type of quantum spin Hall （QSH） insulator in chemically functionalized As （110） and Sb （110） film. According to first-principles calculations, we find that metallic As （110） and Sb （110） films become QSH insulators after being chemically functionalized by hydrogen （H） or halogen （C1 and Br） atoms. The energy gaps of the functionalized films range from 0.121 eV to 0.304 eV, which are sufficiently large for practical applications at room temperature. The energy gaps originate from the spin-orbit coupling （SOC）. The energy gap increases linearly with the increase of the SOC strength λ/λ0. The Z2 invariant and the penetration depth of the edge states are also calculated and studied for the functionalized films.