This research study the effect of diode laser (810 nm), with various power (30, 200, 500) mW in hardness of the material used in the combinations of teeth (ceramics). Hardness was measured for dental ceramic samples d...This research study the effect of diode laser (810 nm), with various power (30, 200, 500) mW in hardness of the material used in the combinations of teeth (ceramics). Hardness was measured for dental ceramic samples divided into four groups, each group containing ten test sample, before and after it irradiated with the diode laser with wavelength 810 nm and different power (30, 200, 500) mW, with irradiation power of 200 mW for duration two minutes and ten minutes to the third and fourth groups, and irradiation power of 30 and 500 mW for duration one minute for the last two groups. The results showed that the increase in the irradiated time of the samples from two minutes to ten minutes, as well as increased power from 30 to 500 mW does not have a significant effect in increasing the hardness of the ceramic material. This study found that the hardness ratio of the samples was increased up to (18.28%), by irradiation of invisible diode laser 810 nm, 30 mW.展开更多
Aim: The study was to fabricate FA nanopowder/Co-Cr-Mo dental alloy nanocomposite using pulsed laser deposition (PLD), and to evaluate bioactivity properties on simulated body fluid. Methods: In this work, the FA nano...Aim: The study was to fabricate FA nanopowder/Co-Cr-Mo dental alloy nanocomposite using pulsed laser deposition (PLD), and to evaluate bioactivity properties on simulated body fluid. Methods: In this work, the FA nanopowder was prepared by mixing calcium hydroxide (Ca(OH)2), phosphorouspent oxide (P2O5) and calcium fluoride (CaF2) in a planetary high energy ball mill using zirconium vial. Fluorapatite (FA) nanopowder was processed in the form of pellet for pulsed laser deposition process. The Co-Cr-Mo alloy was coated with FA nanopowder which was approximately 35 - 65 nm at various laser energy, pressure and time. The X-ray diffraction (XRD) was used to analyze phase, crystallinity and size distribution of Co-Cr-Mo/FA nanocomposite. The surface analysis was by scanning electron microscopy (SEM), Atomic Force microscopy (AFM) and Energy dispersive spectroscopy (EDS). Results: From the results obtained, It was shown that FA nanopowder deposited on Co-Cr-Mo alloy was stable during 14 days of incubation on simulated body fluid. It was also observed that the FA nanopowder coated on the surface of the alloy was still intact after the deposition process, which indicated the bioactivity and biocompatibility of the material. Conclusions: The fabrication of FA nanocomposite based dental alloys (Co-Cr-Mo) using PLD was done successfully. This was confirmed by various characterization techniques, which included XRD, AFM, SEM and EDS.展开更多
AIM: To investigate low intensity laser irradiation phototherapy(LILIP) on the proliferation, mineralization and degradation of dental pulp constructs.METHODS: Stem cells from human exfoliated deciduous teeth(SHED) we...AIM: To investigate low intensity laser irradiation phototherapy(LILIP) on the proliferation, mineralization and degradation of dental pulp constructs.METHODS: Stem cells from human exfoliated deciduous teeth(SHED) were grown to confluence and seeded on collagen scaffolds to create dental pulp constructs. LILIP was delivered to the dental pulp constructs using an 830 nm GaA IAs laser at an output power of 20 m W. The LILIP energy density was 0.4, 0.8, 1.2, and 2.4 J/cm2. After 8 d, the cell proliferation and degradation within the dental pulp constructs were measured using histologic criteria. After 28 d, the effect of LILIP on SHED mineralization was assessed by von Kossa staining.RESULTS: SHED proliferation within the dental pulp constructs varied after exposure to the 0.4, 0.8, 1.2,and 2.4 J/cm2 LILIP energy densities(P < 0.05). The maximum proliferation of SHED in nutrient deficient media was 218% after exposure to a 1.2 J/cm2 LILIP energy density. SHED grown in nutrient deficient media after exposure to a 0.4, 0.8, and 1.2 J/cm2 LILIP energy density, proliferated by 167-218% compared to the untreated(non-LILIP) control group(P < 0.05).SHED exposed to a 0.4, 0.8, and 1.2 J/cm2 LILIP energy density, and grown in optimal nutritional conditions and proliferated by 147%-164% compared to the untreated(non-LILIP) control group(P < 0.05). The exposure of SHED to the highest LILIP energy density(2.4 J/cm2) caused a reduction of the cell proliferation of up to 73% of the untreated(non-LILIP) control(P < 0.05). The amount of mineral produced by SHED increased over time up to 28 d(P < 0.05). The 0.8 and 1.2J/cm2 LILIP energy densities were the most effective at stimulating the increased the mineralization of the SHED from 150%-700% compared to untreated(nonLILIP) control over 28 d(P < 0.05). The degradation of dental pulp constructs was affected by LILIP(P <0.05). The dental pulp constructs grown in optimal nutritional conditions exposed to a 0.8 J/cm2 or 1.2 J/cm2 LILIP energy density had 13% to 16% more degradation than the untreated(non-LILIP) control groups(P < 0.05). The other LILIP energy densities caused a 1%degradation of dental pulp constructs in optimal nutritional conditions(P > 0.05).CONCLUSION: LILIP can enhance or reduce SHED proliferation, degradation and mineralization within dental pulp constructs. LILIP could promote the healing and regeneration of dental tissues.展开更多
Since former president Obama of America put forward the concept of 3D printing or additive manufacturing, it had been putting into use rapidly and getting acceptance widely. In particular, metal additive manufacturing...Since former president Obama of America put forward the concept of 3D printing or additive manufacturing, it had been putting into use rapidly and getting acceptance widely. In particular, metal additive manufacturing machines had been successfully applied with pilot demonstration in industry. However, the present metal additive manufacturing machines cannot be directly used in medical fields such as dental restoration because of some different requirements between industry and medical fields. In this case, this paper is aimed for the development of laser fusion printing machine (LFP), also being called as selective laser melting (SLM), for ceramic teeth crown in dental restoration business. Through the reasonable design and development of key components such as machinery unit, optical unit, electrical controlling unit, and software unit, and the integration, debugging, and optimization of the entire system, the laser fusion printing apparatus for dental restoration has been successfully developed. Key technologies such as machine structure design, optical unit design, electrical controlling system design, system software and process software have been overcome, on the basis of which, a lot of process experiments of medical titanium alloy materials were deeply carried out. At last laser fusion printing technology of titanium alloy was mastered, and titanium dental crown by laser fusion printing with relative density up to 97.37% was realized. After post treatment with porcelain, it was found that the laser fusion printed porcelain teeth with titanium alloy has good metal-ceramic bonding strength, which is equivalent to the quality of traditional porcelain teeth, which showed that laser fusion printing can meet the requirements of dental restoration business and has a broad market outlook.展开更多
To investigate the bacterial colonization on zirconium oxide and titanium surfaces in vivo quantitatively using a confocal laser scanning microscope （CLSM）. Ten samples of zirconium oxide ceramic and commercially pu...To investigate the bacterial colonization on zirconium oxide and titanium surfaces in vivo quantitatively using a confocal laser scanning microscope （CLSM）. Ten samples of zirconium oxide ceramic and commercially pure titanium were fabricated and polished using silicon carbide abrasive paper. One sample from each group was evaluated topographic pattern under a scanning electron microscope. One sample from each group was to evaluate roughness using a profilometer. Eight volunteers were selected. The samples were cemented at the buccal surfaces of upper first molars. All samples were removed after 48 hours, immersed in SYTO-9 and propidium iodide fluorescent to stain for adherent bacteria and obseIved with CLSM. Fewer bacteria were observed in zirconia group than titanium group. However, there was no statistical difference between two groups. The experimental results demonstrate that zirconium oxide may be considered as a promising material for dental implant abutments.展开更多
Aim: 1] Comparative evaluation of the linear depth of induced remineralized lesions after subjecting to fluoride supplements and 2] To assess the average fluorescence at both the demineralized and the remi-neralized z...Aim: 1] Comparative evaluation of the linear depth of induced remineralized lesions after subjecting to fluoride supplements and 2] To assess the average fluorescence at both the demineralized and the remi-neralized zones in all the three study groups under confocal laser scanning microscope. Method: Forty five sound human premolars extracted for orthodon-tic reasons were decoronated 1 mm below the ce-mento-enamel junction and coated with nail varnish except for a 3 × 3 mm window on the buccal surface. The samples were placed in 50 ml of de mineralizing solution at pH 4.6 for 96 hours. Following deminera-lization, the lower half of the 3 × 3 mm window in all the samples were covered with nail varnish to serve as control. The samples were randomly divided into three groups of fifteen teeth each (n = 15) and speci-mens in group A[Nfd] were remineralized using non-fluoridated dentifrice [control], those in groups B [Fd5] and group C [Fd10] using 500 ppm and 1000 ppm of fluoride containing dentifrice, respectively. The specimens were subjected to a 20 day reminera-lization treatment regimen and were sectioned into 100 μm thick sections and two images were captured on the buccal surface from either side of the midpoint of occluso-cervical length using confocal laser scan-ning microscope [CLSM]. Results: were tabulated and statistically analyzed by Anova. Study concluded that 1000 ppm fluoridated dentifrice showed a greater degree of remineralization than other groups and confocal laser scanning microscopes gives promising results in the diagnosis of early enamel lesions over the conventional methods.展开更多
Photoacoustic waves from hemoglobin solutions in dental roots are detected by using a 1064-nm laser and an ultrasonic soft probe based on a composite transducer on the tooth surface. The high-frequency ultrasonic wave...Photoacoustic waves from hemoglobin solutions in dental roots are detected by using a 1064-nm laser and an ultrasonic soft probe based on a composite transducer on the tooth surface. The high-frequency ultrasonic waves are detected from a tooth with a hemoglobin solution in the pulp cavity due to the large heat transfer coefficient and absorption coefficient of hemoglobin. The spectral intensities of frequency components higher than 1 MHz show good correlation with the hemoglobin solution concentrations, and maps of frequency spectra calculated by taking short-time Fourier transforms clearly exhibit the effect of absorbance in dental pulp.展开更多
文摘This research study the effect of diode laser (810 nm), with various power (30, 200, 500) mW in hardness of the material used in the combinations of teeth (ceramics). Hardness was measured for dental ceramic samples divided into four groups, each group containing ten test sample, before and after it irradiated with the diode laser with wavelength 810 nm and different power (30, 200, 500) mW, with irradiation power of 200 mW for duration two minutes and ten minutes to the third and fourth groups, and irradiation power of 30 and 500 mW for duration one minute for the last two groups. The results showed that the increase in the irradiated time of the samples from two minutes to ten minutes, as well as increased power from 30 to 500 mW does not have a significant effect in increasing the hardness of the ceramic material. This study found that the hardness ratio of the samples was increased up to (18.28%), by irradiation of invisible diode laser 810 nm, 30 mW.
文摘Aim: The study was to fabricate FA nanopowder/Co-Cr-Mo dental alloy nanocomposite using pulsed laser deposition (PLD), and to evaluate bioactivity properties on simulated body fluid. Methods: In this work, the FA nanopowder was prepared by mixing calcium hydroxide (Ca(OH)2), phosphorouspent oxide (P2O5) and calcium fluoride (CaF2) in a planetary high energy ball mill using zirconium vial. Fluorapatite (FA) nanopowder was processed in the form of pellet for pulsed laser deposition process. The Co-Cr-Mo alloy was coated with FA nanopowder which was approximately 35 - 65 nm at various laser energy, pressure and time. The X-ray diffraction (XRD) was used to analyze phase, crystallinity and size distribution of Co-Cr-Mo/FA nanocomposite. The surface analysis was by scanning electron microscopy (SEM), Atomic Force microscopy (AFM) and Energy dispersive spectroscopy (EDS). Results: From the results obtained, It was shown that FA nanopowder deposited on Co-Cr-Mo alloy was stable during 14 days of incubation on simulated body fluid. It was also observed that the FA nanopowder coated on the surface of the alloy was still intact after the deposition process, which indicated the bioactivity and biocompatibility of the material. Conclusions: The fabrication of FA nanocomposite based dental alloys (Co-Cr-Mo) using PLD was done successfully. This was confirmed by various characterization techniques, which included XRD, AFM, SEM and EDS.
文摘AIM: To investigate low intensity laser irradiation phototherapy(LILIP) on the proliferation, mineralization and degradation of dental pulp constructs.METHODS: Stem cells from human exfoliated deciduous teeth(SHED) were grown to confluence and seeded on collagen scaffolds to create dental pulp constructs. LILIP was delivered to the dental pulp constructs using an 830 nm GaA IAs laser at an output power of 20 m W. The LILIP energy density was 0.4, 0.8, 1.2, and 2.4 J/cm2. After 8 d, the cell proliferation and degradation within the dental pulp constructs were measured using histologic criteria. After 28 d, the effect of LILIP on SHED mineralization was assessed by von Kossa staining.RESULTS: SHED proliferation within the dental pulp constructs varied after exposure to the 0.4, 0.8, 1.2,and 2.4 J/cm2 LILIP energy densities(P < 0.05). The maximum proliferation of SHED in nutrient deficient media was 218% after exposure to a 1.2 J/cm2 LILIP energy density. SHED grown in nutrient deficient media after exposure to a 0.4, 0.8, and 1.2 J/cm2 LILIP energy density, proliferated by 167-218% compared to the untreated(non-LILIP) control group(P < 0.05).SHED exposed to a 0.4, 0.8, and 1.2 J/cm2 LILIP energy density, and grown in optimal nutritional conditions and proliferated by 147%-164% compared to the untreated(non-LILIP) control group(P < 0.05). The exposure of SHED to the highest LILIP energy density(2.4 J/cm2) caused a reduction of the cell proliferation of up to 73% of the untreated(non-LILIP) control(P < 0.05). The amount of mineral produced by SHED increased over time up to 28 d(P < 0.05). The 0.8 and 1.2J/cm2 LILIP energy densities were the most effective at stimulating the increased the mineralization of the SHED from 150%-700% compared to untreated(nonLILIP) control over 28 d(P < 0.05). The degradation of dental pulp constructs was affected by LILIP(P <0.05). The dental pulp constructs grown in optimal nutritional conditions exposed to a 0.8 J/cm2 or 1.2 J/cm2 LILIP energy density had 13% to 16% more degradation than the untreated(non-LILIP) control groups(P < 0.05). The other LILIP energy densities caused a 1%degradation of dental pulp constructs in optimal nutritional conditions(P > 0.05).CONCLUSION: LILIP can enhance or reduce SHED proliferation, degradation and mineralization within dental pulp constructs. LILIP could promote the healing and regeneration of dental tissues.
文摘Since former president Obama of America put forward the concept of 3D printing or additive manufacturing, it had been putting into use rapidly and getting acceptance widely. In particular, metal additive manufacturing machines had been successfully applied with pilot demonstration in industry. However, the present metal additive manufacturing machines cannot be directly used in medical fields such as dental restoration because of some different requirements between industry and medical fields. In this case, this paper is aimed for the development of laser fusion printing machine (LFP), also being called as selective laser melting (SLM), for ceramic teeth crown in dental restoration business. Through the reasonable design and development of key components such as machinery unit, optical unit, electrical controlling unit, and software unit, and the integration, debugging, and optimization of the entire system, the laser fusion printing apparatus for dental restoration has been successfully developed. Key technologies such as machine structure design, optical unit design, electrical controlling system design, system software and process software have been overcome, on the basis of which, a lot of process experiments of medical titanium alloy materials were deeply carried out. At last laser fusion printing technology of titanium alloy was mastered, and titanium dental crown by laser fusion printing with relative density up to 97.37% was realized. After post treatment with porcelain, it was found that the laser fusion printed porcelain teeth with titanium alloy has good metal-ceramic bonding strength, which is equivalent to the quality of traditional porcelain teeth, which showed that laser fusion printing can meet the requirements of dental restoration business and has a broad market outlook.
基金Funded by the National Natural Science Foundation of China(No.81271179)the Scientific Research Foundation for Returned Scholars,Ministry of Education of China(No.(2011)1568)the Science and Technology Program of Shanghai Pudong New Area Health Bureau(No.PW2010A-14)
文摘To investigate the bacterial colonization on zirconium oxide and titanium surfaces in vivo quantitatively using a confocal laser scanning microscope （CLSM）. Ten samples of zirconium oxide ceramic and commercially pure titanium were fabricated and polished using silicon carbide abrasive paper. One sample from each group was evaluated topographic pattern under a scanning electron microscope. One sample from each group was to evaluate roughness using a profilometer. Eight volunteers were selected. The samples were cemented at the buccal surfaces of upper first molars. All samples were removed after 48 hours, immersed in SYTO-9 and propidium iodide fluorescent to stain for adherent bacteria and obseIved with CLSM. Fewer bacteria were observed in zirconia group than titanium group. However, there was no statistical difference between two groups. The experimental results demonstrate that zirconium oxide may be considered as a promising material for dental implant abutments.
文摘Aim: 1] Comparative evaluation of the linear depth of induced remineralized lesions after subjecting to fluoride supplements and 2] To assess the average fluorescence at both the demineralized and the remi-neralized zones in all the three study groups under confocal laser scanning microscope. Method: Forty five sound human premolars extracted for orthodon-tic reasons were decoronated 1 mm below the ce-mento-enamel junction and coated with nail varnish except for a 3 × 3 mm window on the buccal surface. The samples were placed in 50 ml of de mineralizing solution at pH 4.6 for 96 hours. Following deminera-lization, the lower half of the 3 × 3 mm window in all the samples were covered with nail varnish to serve as control. The samples were randomly divided into three groups of fifteen teeth each (n = 15) and speci-mens in group A[Nfd] were remineralized using non-fluoridated dentifrice [control], those in groups B [Fd5] and group C [Fd10] using 500 ppm and 1000 ppm of fluoride containing dentifrice, respectively. The specimens were subjected to a 20 day reminera-lization treatment regimen and were sectioned into 100 μm thick sections and two images were captured on the buccal surface from either side of the midpoint of occluso-cervical length using confocal laser scan-ning microscope [CLSM]. Results: were tabulated and statistically analyzed by Anova. Study concluded that 1000 ppm fluoridated dentifrice showed a greater degree of remineralization than other groups and confocal laser scanning microscopes gives promising results in the diagnosis of early enamel lesions over the conventional methods.
文摘Photoacoustic waves from hemoglobin solutions in dental roots are detected by using a 1064-nm laser and an ultrasonic soft probe based on a composite transducer on the tooth surface. The high-frequency ultrasonic waves are detected from a tooth with a hemoglobin solution in the pulp cavity due to the large heat transfer coefficient and absorption coefficient of hemoglobin. The spectral intensities of frequency components higher than 1 MHz show good correlation with the hemoglobin solution concentrations, and maps of frequency spectra calculated by taking short-time Fourier transforms clearly exhibit the effect of absorbance in dental pulp.
