In order to reduce sulphur ( S ) and phosphorus ( P ) impurities in deposited metal, a small amount of rare earth (RE) lanthanum ( La) and yttrium (Y) were added into the coating ofE4303 electrode, a low car...In order to reduce sulphur ( S ) and phosphorus ( P ) impurities in deposited metal, a small amount of rare earth (RE) lanthanum ( La) and yttrium (Y) were added into the coating ofE4303 electrode, a low carbon steel electrode. The microstructures of deposited metal were analyzed with metalloscope, and then the content of S and P was examined by energy dispenive X-ray spectrometer ( EDXS ), and by wavelength dispersive X-ray fluorescence (XRF) spectrometer for further examination. The results show that the proper addition of La and Y can be beneficial to the desulfurization and dephosphorization of the deposited metal. Certainly, difference in the addition amount of La and Y could lead to various desulfurization and dephosphorization efficiency, in which the former is more obvious than the latter. With the proper amount of La attd Y, there is finer microstructure in deposited metal, and mechanical properties are improved as well. The S content in deposited metal with added La and Y decreases by 44. 44 wt. % , while the P content 6. 67 wt. %, compared with that in deposited metal without La and II.展开更多
The microstructure of E911 deposited metal was observed and the effect of heat input and postweld heat treatment on microstructure and impact toughness was investigated. The microstructure consists of tempered martens...The microstructure of E911 deposited metal was observed and the effect of heat input and postweld heat treatment on microstructure and impact toughness was investigated. The microstructure consists of tempered martensite and residual δ- ferrite. The morphology of tempered martensite is columnar and the residual δ-ferrite is polygonal. With the increase in heat input, the width of columnar martensite grain and the size of residual δ-ferrite increased, whereas the volume fraction of residual δ-ferrite varied slightly. The impact toughness decreased as heat input increased. The result reveals that coarsening columnar martensite grain and δ-ferrite have greater effect on impact toughness than volume fraction of residual δ-ferrite. As the time of postweld heat treatment is exceeded 8h, aggregation of M23 C6occurs in some grain boundaries or lath interfaces. The partial aggregation of M23 C6 results in the decrease in impact toughness.展开更多
By means of metallographic microscope(OM),scanning electron microscope(SEM),back scattering electron diffraction(EBSD)and transmission electron microscope(TEM),the effect of Cu on microstructure transformation and mec...By means of metallographic microscope(OM),scanning electron microscope(SEM),back scattering electron diffraction(EBSD)and transmission electron microscope(TEM),the effect of Cu on microstructure transformation and mechanical properties of deposited metal of 590MPa class steel welding wire was studied.The results show that the microstructure of deposited metal is composed of acicular ferrite,lamellar bainite,granular bainite and residual austenite.With the increase of Cu content,the phase transition temperature of the deposited metal decreases,making the phase transition region of ferrite and pearlite shift to the right,expanding the phase transition region of bainite and shrinking the phase transition region of ferrite and pearlite.The microstructure of deposited metal changed,the content of M-A elements increased but the size decreased,and the ferrite-bainite biphasic microstructure was matched.The reduction of M-A component content in strips and blocks and the reduction of effective grain size will reduce the nucleation probability of microcracks,increase crack growth resistance,and improve the impact toughness of the deposited metal.展开更多
Alloy element and microstructure are key factors that dominate mechanical and corrosion resistant properties of weathering steel. The effect of Mo on microstructure, mechanical properties and corrosion resistant prope...Alloy element and microstructure are key factors that dominate mechanical and corrosion resistant properties of weathering steel. The effect of Mo on microstructure, mechanical properties and corrosion resistant property of depos ited metal was investigated. Experimental results show that with the increase of Mo content in deposited metals, the phase transformation temperature decreases, and the ferrite zone in CCT diagram moves rightward, resulting in en larged bainite zone and reduced ferrite and pearlite zone. The addition of 0.24 mass% Mo in deposited metal results in the increase of tensile strength, more M-A constituent and less high angle grain which reduce the low temperature toughness. It is found that Mo can raise the weathering resistance of deposited metal in industrial atmosphere. Analy sis indicates that Mo may enrich in the inner rust layer, produce MoO3, enhance the formation of compact rust film and impede the anode dissolution reaction. Granular bainite in deposited metals displays better corrosion resistance than acicular ferrite during the initial corrosion stage, but its long-term influence on the corrosion resistance is limited.展开更多
The effect of Al in Ti-microalloyed welding wire on microstructure and toughness of deposited metals is studied.The results show that the deposited metal toughness worsens with increasing Al in wire' The mechanis...The effect of Al in Ti-microalloyed welding wire on microstructure and toughness of deposited metals is studied.The results show that the deposited metal toughness worsens with increasing Al in wire' The mechanism of Al is as follows:(1) Al makes oxygen content in deposited metal increase.(2)Al restrains the formation of Ti-rich oxide inclusion, which causes granular bainite microstructure in deposited metal.(3)The content of solute Ti in deposited metal increases with Al content in welding wire,as a result,a part of carbonrich constitution in deposited metal is in the form of twin martensite.展开更多
The microstractures of 9Cr-lMo multipass deposited metal were observed. The effect of microstructure on impact toughness of 9Cr-lMo multipass deposited metal with varying heat inputs was investigated. Result shows tha...The microstractures of 9Cr-lMo multipass deposited metal were observed. The effect of microstructure on impact toughness of 9Cr-lMo multipass deposited metal with varying heat inputs was investigated. Result shows that fine-grained microstructure occurs in reheated zones. The absorbed energy increases with the increase of volume fraction of fine-grained microstructure , suggesting that the volume fraction of fine-grained microstracture influences directly on impact toughness. The increasing ratio of fine-grained zone thickness to weld layer thickness is responsible for improving impact toughness after PWHT.展开更多
The single solid source precursor, cobalt (Ⅱ) acetylacetonate was prepared and characterized by infrared spectroscopy. Thin films of cobalt oxide were deposited on soda lime glass substrates through the pyrolysis ...The single solid source precursor, cobalt (Ⅱ) acetylacetonate was prepared and characterized by infrared spectroscopy. Thin films of cobalt oxide were deposited on soda lime glass substrates through the pyrolysis (metal organic chemical vapour deposition (MOCVD)) of single solid source precursor, cobalt acetylacetonate, Co[C5H7O2]2 at a temperature of 420℃. The compositional characterization carried out by rutherford backscattering spectroscopy and X-ray diffraction (XRD), showed that the films have a stoichiometry of Co2O3 and an average thickness of 227±0.2 nm. A direct energy gap of 2,15±0.01 eV was calculated by the data obtained by optical absorption spectroscopy. The morphology of the films obtained by scanning electron microscopy, showed that the grains were continuous and uniformly distributed at various magnifications, while the average grain size was less than i micron for the deposited thin films of cobalt oxide.展开更多
Copper was surfaced on the Q235 substrate by shielded metal arc welding (SMAW) and tungsten inert-gas (TIG) arc welding, the regularity of iron element in deposited metal was analyzed by metallograph, scanning ele...Copper was surfaced on the Q235 substrate by shielded metal arc welding (SMAW) and tungsten inert-gas (TIG) arc welding, the regularity of iron element in deposited metal was analyzed by metallograph, scanning electron microscopy and energy disperse spectroscopy. The results indicate that with the increase of SMA W welding speed, the iron content decreases and the granular or spherical iron becomes more bulky in the overlay. The iron content obviously decreases with the increase of surfacing layers' numbers in multilayer welding because of the substrate dilution. On the third layer, the microstrueture of deposited metal is single-phase e-copper. Under the influence of welding methods, the granular or spherical crystal morphology is more likely to form in SMAW for the more divergent arc heat, but is dendrite in TIG welding because of centralized arc energy.展开更多
Granitic pegmatites are commonly thought to form by fractional crystallization or by liquid immiscibility of granitic magma; however, these proposals are based mainly on analyses of fluid and melt inclusions. Here, we...Granitic pegmatites are commonly thought to form by fractional crystallization or by liquid immiscibility of granitic magma; however, these proposals are based mainly on analyses of fluid and melt inclusions. Here, we use the Jiajika pegmatite deposit, the largest spodumene deposit in Asia, as a case study to investigate ore forming processes using isotope dating. Dating of a single granite sample from the Jiajika deposit using multiple methods gave a zircon U-Pb SHRIMP age of 208.4 ~ 3.9 Ma, an 4~Ar/39Ar age for muscovite of 182.9 ~ 1.7 Ma, and an 4~Ar/39Ar age for biotite of 169.9 + 1.6 Ma. Based on these dating results and the 4~Ar/39Ar age of muscovite from the Jiajika pegmatite, a temperature-time cooling track for the Jiajika granite was constructed using closure temperatures of the different isotope systems. This track indicates that the granite cooled over ^-40 m. y., with segregation of the pegmatite fluid from the granitic magma at a temperature of ~700~C. This result suggests that the Jiajika pegmatite formed not by fractional crystallization, but by segregation of an immiscible liquid from the granitic magma. When compared with fractional crystallization, the relatively early timing of segregation of an immiscible liquid from a granitic magma can prevent the precipitation of ore-forming elements during crystallization, and suggests that liquid immiscibility could be an important ore-forming process for rare metal pegmatities. We also conclude that isotope dating is a method that can potentially be used to determine the dominant ore-forming processes that occurred during the formation of granite-related ore deposits, and suggest that this method can be employed to determine the formation history of the W-Sn ore deposits found elsewhere within the Nanling Metallogenic Belt.展开更多
With the rapid developments of marine resource exploitation,mounts of marine engineering equipment are settled on the ocean.When it is not possible to move the damaged equipment into a dry dock,welding operations must...With the rapid developments of marine resource exploitation,mounts of marine engineering equipment are settled on the ocean.When it is not possible to move the damaged equipment into a dry dock,welding operations must be performed in underwater environments.The underwater laser welding/cladding technique is a promising and advanced technique which could be widely applied to the maintenance of the damaged equipment.The present review paper aims to present a critical analysis and engineering overview of the underwater laser welding/cladding technique.First,we elaborated recent advances and key issues of drainage nozzles all over the world.Next,we presented the underwater laser processing and microstructural-mechanical behavior of repaired marine materials.Then,the newly developed powder-feeding based and wire-feeding based underwater laser direct metal deposition techniques were reviewed.The differences between the convection,conduction,and the metallurgical kinetics in the melt pools during underwater laser direct metal deposition and in-air laser direct metal deposition were illustrated.After that,several challenges that need to be overcame to achieve the full potential of the underwater laser welding/cladding technique are proposed.Finally,suggestions for future directions to aid the development of underwater laser welding/cladding technology and underwater metallurgical theory are provided.The present review will not only enrich the knowledge in the underwater repair technology,but also provide important guidance for the potential applications of the technology on the marine engineering.展开更多
Physicochemical parameters of mineralization such as temperature, pressure, salinity, density, composition and boiling of ore fluids as well as pH, Eh, fo2 and reducing parameter in theprocess of mineralization of maj...Physicochemical parameters of mineralization such as temperature, pressure, salinity, density, composition and boiling of ore fluids as well as pH, Eh, fo2 and reducing parameter in theprocess of mineralization of major ore deposits in the study district have been obtained by the authors through systematic observation and determination of characteristics and phase changes of fluid inclusions at different temperatures and analysis of gaseous and liquid phase compositions of the inclusions, thus providing a scientific basis for the division of mineralization-alteration stages, types of mineral deposits and minerogenetic series and the deepening of the knowledge about the ore-forming processes and mechanisms of mineral deposits. It is indicated that the deposits of the same type have similar fluid inclusion geochemical features and physicochemical parameters though they belong to different minerogenetic series, while the compositions of inclusions are not conditioned by deposit types but closely related to the minerogenetic series of deposits.展开更多
The photocatalytic performance of g-C_(3)N_(4) for CO_(2) conversion is still inadequate by several shortfalls including the instability,insu cient solar light absorption and rapid charge carrier's recombination r...The photocatalytic performance of g-C_(3)N_(4) for CO_(2) conversion is still inadequate by several shortfalls including the instability,insu cient solar light absorption and rapid charge carrier's recombination rate. To solve these problems,herein,noble metals(Pt and Au)decorated Sr-incorporated g-C_(3)N_(4) photocatalysts are fabricated via the simple calcination and photo-deposition methods. The Sr-incorporation remarkably reduced the g-C_(3)N_(4) band gap from 2.7 to 2.54 eV,as evidenced by the UV–visible absorption spectra and the density functional theory results. The CO_(2) conversion performance of the catalysts was evaluated under visible light irradiation. The Pt/0.15 Sr-CN sample produced 48.55 and 74.54 μmol h-1 g-1 of CH_(4) and CO,respectively.These amounts are far greater than that produced by the Au/0.15 Sr-CN,0.15 Sr-CN,and CN samples. A high quantum e ciency of 2.92% is predicted for the Pt/0.15 Sr-CN sample. Further,the stability of the photocatalyst is confirmed via the photocatalytic recyclable test. The improved CO_(2) conversion performance of the catalyst is accredited to the promoted light absorption and remarkably enhanced charge separation via the Sr-incorporated mid gap states and the localized surface plasmon resonance e ect induced by noble metal nanoparticles.This work will provide a new approach for promoting the catalytic e ciency of g-C_(3)N_(4) for e cient solar fuel production.展开更多
Additive manufacturing(AM)is an emerging customized three-dimensional(3D)functional product fabrication technology.It provides a higher degree of design freedom,reduces manufacturing steps,cost and production cycles.H...Additive manufacturing(AM)is an emerging customized three-dimensional(3D)functional product fabrication technology.It provides a higher degree of design freedom,reduces manufacturing steps,cost and production cycles.However,existing metallic component 3D printing techniques are mainly for the manufacture of single material components.With the increasing commercial applications of AM technologies,the need for 3D printing of more than one type of dissimilar materials in a single component increases.Therefore,investigations on multi-material AM(MMAM)emerge over the past decade.Lasers are currently widely used for the AM of metallic components where high temperatures are involved.Here we report the progress and trend in laser-based macro-and micro-scale AM of multiple metallic components.The methods covered in this paper include laser powder bed fusion,laser powder directed energy deposition,and laser-induced forward transfer for MMAM applications.The principles and process/material characteristics are described.Potential applications and challenges are discussed.Finally,future research directions and prospects are proposed.展开更多
Objective The Huashi Village in Xinglong County of Hebei Province is located in the Yanshan subsidence zone in the central eastern North China Plate, which is 137 km away from Beijing City (Fig. la). This area has ...Objective The Huashi Village in Xinglong County of Hebei Province is located in the Yanshan subsidence zone in the central eastern North China Plate, which is 137 km away from Beijing City (Fig. la). This area has undergone large -scale magmatic intrusion affected by the tectonic compression of the Pacific Plate in the Mesozoic (known as the Yanshanian movement) to form many alkaline rocks such as the Wulingshan rock mass. Previous studies have conducted petrological research and reconnaissance survey of rare metal ores in this area (Tian Shuzhang and Guo Zongshan, 1981; Xu Baoling et al., 1996). In 2016, the Qinhuangdao Mineral and Hydrology Engineering Geological Brigade of Hebei Bureau of Geology and Mineral Resources Exploration implemented the project of Reconnaissance of Rare Metal Ores Including Rubidium in Huashi Village of Xinglong County, Hebei Province, and discovered super-large rare metal deposits of rubidium and biobium in the Madi alkali feldspar granite bodies in the Huashi Village to achieve great breakthrough of rare metal ore prospecting.展开更多
Progress in materials development is often paced by the time required to produce and evaluate a large number of alloys with different chemical compositions.This applies especially to refractory high-entropy alloys(RHE...Progress in materials development is often paced by the time required to produce and evaluate a large number of alloys with different chemical compositions.This applies especially to refractory high-entropy alloys(RHEAs),which are difficult to synthesize and process by conventional methods.To evaluate a possible way to accelerate the process,high-throughput laser metal deposition was used in this work to prepare a quinary RHEA,TiZrNbHfTa,as well as its quaternary and ternary subsystems by in-situ alloying of elemental powders.Compositionally graded variants of the quinary RHEA were also analyzed.Our results show that the influence of various parameters such as powder shape and purity,alloy composition,and especially the solidification range,on the processability,microstructure,porosity,and mechanical properties can be investigated rapidly.The strength of these alloys was mainly affected by the oxygen and nitrogen contents of the starting powders,while substitutional solid solution strengthening played a minor role.展开更多
In this work, the wafer bowing during growth can be in-situ measured by a reflectivity mapping method in the 3×2 Thomas Swan close coupled showerhead metal organic chemical vapor deposition(MOCVD) system. The r...In this work, the wafer bowing during growth can be in-situ measured by a reflectivity mapping method in the 3×2 Thomas Swan close coupled showerhead metal organic chemical vapor deposition(MOCVD) system. The reflectivity mapping method is usually used to measure the film thickness and growth rate. The wafer bowing caused by stresses(tensile and compressive) during the epitaxial growth leads to a temperature variation at different positions on the wafer, and the lower growth temperature leads to a faster growth rate and vice versa. Therefore, the wafer bowing can be measured by analyzing the discrepancy of growth rates at different positions on the wafer. Furthermore, the wafer bowings were confirmed by the ex-situ wafer bowing measurement. High-resistivity and low-resistivity Si substrates were used for epitaxial growth. In comparison with low-resistivity Si substrate, Ga N grown on high-resistivity substrate shows a larger wafer bowing caused by the highly compressive stress introduced by compositionally graded Al Ga N buffer layer. This transition of wafer bowing can be clearly in-situ measured by using the reflectivity mapping method.展开更多
High-performance low-leakage-current A1GaN/GaN high electron mobility transistors (HEMTs) on silicon (111) sub- strates grown by metal organic chemical vapor deposition (MOCVD) with a novel partially Magnesium ...High-performance low-leakage-current A1GaN/GaN high electron mobility transistors (HEMTs) on silicon (111) sub- strates grown by metal organic chemical vapor deposition (MOCVD) with a novel partially Magnesium (Mg)-doped GaN buffer scheme have been fabricated successfully. The growth and DC results were compared between Mg-doped GaN buffer layer and a unintentionally onμe. A 1μ m gate-length transistor with Mg-doped buffer layer exhibited an OFF-state drain leakage current of 8.3 × 10-8 A/mm, to our best knowledge, which is the lowest value reported for MOCVD-grown A1GaN/GaN HEMTs on Si featuring the same dimension and structure. The RF characteristics of 0.25-μ m gate length T-shaped gate HEMTs were also investigated.展开更多
CaN nanorods are successfully fabricated by adjusting the flow rate ratio of hydrogen (H2)/nitrogen (N2) and growth temperature of the selective area growth (SAG) method with metal organic chemical vapor deposit...CaN nanorods are successfully fabricated by adjusting the flow rate ratio of hydrogen (H2)/nitrogen (N2) and growth temperature of the selective area growth (SAG) method with metal organic chemical vapor deposition (MOCVD). The SAG template is obtained by nanospherical-lens photolithography. It is found that increasing the flow rate of 1-12 will change the CaN crystal shape from pyramid to vertical rod, while increasing the growth temperature will reduce the diameters of GaN rods to nanometer scale. Finally the CaN nanorods with smooth lateral surface and relatively good quality are obtained under the condition that the H2:N2 ratio is 1:1 and the growth temperature is 1030℃. The good crystal quality and orientation of GaN nanorods are confirmed by high resolution transmission electron microscopy. The cathodoluminescence spectrum suggests that the crystal and optical quality is also improved with increasing the temperature.展开更多
CeO2 and Ce0.8M0.2O2-d films (M = Mn, Y, Gd, Sm, Nd and La) with (00l) preferred orientation have been prepared on biaxially textured Ni-W substrates by metal organic decomposition (MOD) method. The factors infl...CeO2 and Ce0.8M0.2O2-d films (M = Mn, Y, Gd, Sm, Nd and La) with (00l) preferred orientation have been prepared on biaxially textured Ni-W substrates by metal organic decomposition (MOD) method. The factors influencing the formation of cracks on the surface of these CeO2 and doped CeO2 films on Ni-W substrates were explored by X-ray diffraction (XRD), scanning electron microscopy (SEM) analysis, atomic force microscopy (AFM) and differential scanning calorimetry (DSC). The results indicate that many factors, such as the change of the ionic radii of doping cations, the transformation of crystal structure and the formation of oxygen vacancies in lattices at high annealing temperature, may be related to the formation of cracks on the surface of these films. However, the crack formation shows no dependence on the crystal lattice mismatch degree of the films with Ni-W substrates. Moreover, the suppression of surface cracks is related to the change of intrinsic elasticity of CeO2 film with doping of cations with a larger radius. SEM and AFM investigations of Ce0.8M0.2O2-d (M = Y, Gd, Sm, Nd and La) films reveal the dense, smooth and crack-free microstructure, and their lattice parameters match well with that of YBCO, illuminating that they are potentially suitable to be as buffer layer, especially as cap layer in multi-layer architecture of buffer layer for coated conductors.展开更多
The 2205 duplex stainless + DH36 clad steel plate was welded by gas metal arc welding(GMAW), and the welding performance of the clad steel plate was investigated. The results show that the adaptability of the weldi...The 2205 duplex stainless + DH36 clad steel plate was welded by gas metal arc welding(GMAW), and the welding performance of the clad steel plate was investigated. The results show that the adaptability of the welding procedure for the base metal of carbon steel, the transition layer, and the cladding material is excellent. The test results indicate that the phase proportion and component dilution of the GMAW-welded joints of clad steel plate can be effectively controlled to yield joints with good mechanical properties and corrosion resistance.展开更多
基金This project is supported by National Natural Science Foundation of China ( Grant No. 51305178) Xuzhou City Science and Technology Plan Projects (Grant No. XC12A013).
文摘In order to reduce sulphur ( S ) and phosphorus ( P ) impurities in deposited metal, a small amount of rare earth (RE) lanthanum ( La) and yttrium (Y) were added into the coating ofE4303 electrode, a low carbon steel electrode. The microstructures of deposited metal were analyzed with metalloscope, and then the content of S and P was examined by energy dispenive X-ray spectrometer ( EDXS ), and by wavelength dispersive X-ray fluorescence (XRF) spectrometer for further examination. The results show that the proper addition of La and Y can be beneficial to the desulfurization and dephosphorization of the deposited metal. Certainly, difference in the addition amount of La and Y could lead to various desulfurization and dephosphorization efficiency, in which the former is more obvious than the latter. With the proper amount of La attd Y, there is finer microstructure in deposited metal, and mechanical properties are improved as well. The S content in deposited metal with added La and Y decreases by 44. 44 wt. % , while the P content 6. 67 wt. %, compared with that in deposited metal without La and II.
基金Acknowledgements The authors acknowledge gratefully to the financial support for this work from National Natural Science Foundation of China and Baosteel (No. 50734004) and the assistance of Welding Laboratory of Baosteel Group.
文摘The microstructure of E911 deposited metal was observed and the effect of heat input and postweld heat treatment on microstructure and impact toughness was investigated. The microstructure consists of tempered martensite and residual δ- ferrite. The morphology of tempered martensite is columnar and the residual δ-ferrite is polygonal. With the increase in heat input, the width of columnar martensite grain and the size of residual δ-ferrite increased, whereas the volume fraction of residual δ-ferrite varied slightly. The impact toughness decreased as heat input increased. The result reveals that coarsening columnar martensite grain and δ-ferrite have greater effect on impact toughness than volume fraction of residual δ-ferrite. As the time of postweld heat treatment is exceeded 8h, aggregation of M23 C6occurs in some grain boundaries or lath interfaces. The partial aggregation of M23 C6 results in the decrease in impact toughness.
文摘By means of metallographic microscope(OM),scanning electron microscope(SEM),back scattering electron diffraction(EBSD)and transmission electron microscope(TEM),the effect of Cu on microstructure transformation and mechanical properties of deposited metal of 590MPa class steel welding wire was studied.The results show that the microstructure of deposited metal is composed of acicular ferrite,lamellar bainite,granular bainite and residual austenite.With the increase of Cu content,the phase transition temperature of the deposited metal decreases,making the phase transition region of ferrite and pearlite shift to the right,expanding the phase transition region of bainite and shrinking the phase transition region of ferrite and pearlite.The microstructure of deposited metal changed,the content of M-A elements increased but the size decreased,and the ferrite-bainite biphasic microstructure was matched.The reduction of M-A component content in strips and blocks and the reduction of effective grain size will reduce the nucleation probability of microcracks,increase crack growth resistance,and improve the impact toughness of the deposited metal.
基金Item Sponsored by International Science and Technology Cooperation Program of China(2015DFA51460)
文摘Alloy element and microstructure are key factors that dominate mechanical and corrosion resistant properties of weathering steel. The effect of Mo on microstructure, mechanical properties and corrosion resistant property of depos ited metal was investigated. Experimental results show that with the increase of Mo content in deposited metals, the phase transformation temperature decreases, and the ferrite zone in CCT diagram moves rightward, resulting in en larged bainite zone and reduced ferrite and pearlite zone. The addition of 0.24 mass% Mo in deposited metal results in the increase of tensile strength, more M-A constituent and less high angle grain which reduce the low temperature toughness. It is found that Mo can raise the weathering resistance of deposited metal in industrial atmosphere. Analy sis indicates that Mo may enrich in the inner rust layer, produce MoO3, enhance the formation of compact rust film and impede the anode dissolution reaction. Granular bainite in deposited metals displays better corrosion resistance than acicular ferrite during the initial corrosion stage, but its long-term influence on the corrosion resistance is limited.
文摘The effect of Al in Ti-microalloyed welding wire on microstructure and toughness of deposited metals is studied.The results show that the deposited metal toughness worsens with increasing Al in wire' The mechanism of Al is as follows:(1) Al makes oxygen content in deposited metal increase.(2)Al restrains the formation of Ti-rich oxide inclusion, which causes granular bainite microstructure in deposited metal.(3)The content of solute Ti in deposited metal increases with Al content in welding wire,as a result,a part of carbonrich constitution in deposited metal is in the form of twin martensite.
文摘The microstractures of 9Cr-lMo multipass deposited metal were observed. The effect of microstructure on impact toughness of 9Cr-lMo multipass deposited metal with varying heat inputs was investigated. Result shows that fine-grained microstructure occurs in reheated zones. The absorbed energy increases with the increase of volume fraction of fine-grained microstructure , suggesting that the volume fraction of fine-grained microstracture influences directly on impact toughness. The increasing ratio of fine-grained zone thickness to weld layer thickness is responsible for improving impact toughness after PWHT.
基金the Third World Academy of Science (TWAS, Grant #93-058 R6/PHYS/AF/AC)Obafemi Awolowo University(University Research Committee URC) for supporting this project
文摘The single solid source precursor, cobalt (Ⅱ) acetylacetonate was prepared and characterized by infrared spectroscopy. Thin films of cobalt oxide were deposited on soda lime glass substrates through the pyrolysis (metal organic chemical vapour deposition (MOCVD)) of single solid source precursor, cobalt acetylacetonate, Co[C5H7O2]2 at a temperature of 420℃. The compositional characterization carried out by rutherford backscattering spectroscopy and X-ray diffraction (XRD), showed that the films have a stoichiometry of Co2O3 and an average thickness of 227±0.2 nm. A direct energy gap of 2,15±0.01 eV was calculated by the data obtained by optical absorption spectroscopy. The morphology of the films obtained by scanning electron microscopy, showed that the grains were continuous and uniformly distributed at various magnifications, while the average grain size was less than i micron for the deposited thin films of cobalt oxide.
文摘Copper was surfaced on the Q235 substrate by shielded metal arc welding (SMAW) and tungsten inert-gas (TIG) arc welding, the regularity of iron element in deposited metal was analyzed by metallograph, scanning electron microscopy and energy disperse spectroscopy. The results indicate that with the increase of SMA W welding speed, the iron content decreases and the granular or spherical iron becomes more bulky in the overlay. The iron content obviously decreases with the increase of surfacing layers' numbers in multilayer welding because of the substrate dilution. On the third layer, the microstrueture of deposited metal is single-phase e-copper. Under the influence of welding methods, the granular or spherical crystal morphology is more likely to form in SMAW for the more divergent arc heat, but is dendrite in TIG welding because of centralized arc energy.
基金supported by grants from the National Natural Science Foundation of China (40702014)the China Postdoctoral Science Foundation (2008044018,200902580)+1 种基金the Chinese SinoProbe Project (SinoProbe-03-01)the National Nonprofit Institute Research Grant of IMR,GAGS(K1001)
文摘Granitic pegmatites are commonly thought to form by fractional crystallization or by liquid immiscibility of granitic magma; however, these proposals are based mainly on analyses of fluid and melt inclusions. Here, we use the Jiajika pegmatite deposit, the largest spodumene deposit in Asia, as a case study to investigate ore forming processes using isotope dating. Dating of a single granite sample from the Jiajika deposit using multiple methods gave a zircon U-Pb SHRIMP age of 208.4 ~ 3.9 Ma, an 4~Ar/39Ar age for muscovite of 182.9 ~ 1.7 Ma, and an 4~Ar/39Ar age for biotite of 169.9 + 1.6 Ma. Based on these dating results and the 4~Ar/39Ar age of muscovite from the Jiajika pegmatite, a temperature-time cooling track for the Jiajika granite was constructed using closure temperatures of the different isotope systems. This track indicates that the granite cooled over ^-40 m. y., with segregation of the pegmatite fluid from the granitic magma at a temperature of ~700~C. This result suggests that the Jiajika pegmatite formed not by fractional crystallization, but by segregation of an immiscible liquid from the granitic magma. When compared with fractional crystallization, the relatively early timing of segregation of an immiscible liquid from a granitic magma can prevent the precipitation of ore-forming elements during crystallization, and suggests that liquid immiscibility could be an important ore-forming process for rare metal pegmatities. We also conclude that isotope dating is a method that can potentially be used to determine the dominant ore-forming processes that occurred during the formation of granite-related ore deposits, and suggest that this method can be employed to determine the formation history of the W-Sn ore deposits found elsewhere within the Nanling Metallogenic Belt.
基金Supported by National Basic Scientific Research Project(Grant No.JCKY2017110B001)Jiangsu Provincial Postgraduate Research&Practice Innovation Program of China(Grant No.KYCX20_0080)。
文摘With the rapid developments of marine resource exploitation,mounts of marine engineering equipment are settled on the ocean.When it is not possible to move the damaged equipment into a dry dock,welding operations must be performed in underwater environments.The underwater laser welding/cladding technique is a promising and advanced technique which could be widely applied to the maintenance of the damaged equipment.The present review paper aims to present a critical analysis and engineering overview of the underwater laser welding/cladding technique.First,we elaborated recent advances and key issues of drainage nozzles all over the world.Next,we presented the underwater laser processing and microstructural-mechanical behavior of repaired marine materials.Then,the newly developed powder-feeding based and wire-feeding based underwater laser direct metal deposition techniques were reviewed.The differences between the convection,conduction,and the metallurgical kinetics in the melt pools during underwater laser direct metal deposition and in-air laser direct metal deposition were illustrated.After that,several challenges that need to be overcame to achieve the full potential of the underwater laser welding/cladding technique are proposed.Finally,suggestions for future directions to aid the development of underwater laser welding/cladding technology and underwater metallurgical theory are provided.The present review will not only enrich the knowledge in the underwater repair technology,but also provide important guidance for the potential applications of the technology on the marine engineering.
文摘Physicochemical parameters of mineralization such as temperature, pressure, salinity, density, composition and boiling of ore fluids as well as pH, Eh, fo2 and reducing parameter in theprocess of mineralization of major ore deposits in the study district have been obtained by the authors through systematic observation and determination of characteristics and phase changes of fluid inclusions at different temperatures and analysis of gaseous and liquid phase compositions of the inclusions, thus providing a scientific basis for the division of mineralization-alteration stages, types of mineral deposits and minerogenetic series and the deepening of the knowledge about the ore-forming processes and mechanisms of mineral deposits. It is indicated that the deposits of the same type have similar fluid inclusion geochemical features and physicochemical parameters though they belong to different minerogenetic series, while the compositions of inclusions are not conditioned by deposit types but closely related to the minerogenetic series of deposits.
基金financially supported by the Ministry of Science and Technology of China (Grant No. 2018YFA0702100)the National Natural Science Foundation of China (Grant No. 11874169,51972129)+4 种基金the National Key R&D Program of China (Grant No. 2017YFE0120500)the Key Research and Development Program of Hubei (Grant No. 2020BAB079)the South Xinjiang Innovation and Development Program of Key Industries of Xinjiang Production and Construction Corps (Grants No. 2020DB002)Engineering and Physical Sciences Research Council (EP/T025875/1)the Hubei “ChuTian Young Scholar” program。
文摘The photocatalytic performance of g-C_(3)N_(4) for CO_(2) conversion is still inadequate by several shortfalls including the instability,insu cient solar light absorption and rapid charge carrier's recombination rate. To solve these problems,herein,noble metals(Pt and Au)decorated Sr-incorporated g-C_(3)N_(4) photocatalysts are fabricated via the simple calcination and photo-deposition methods. The Sr-incorporation remarkably reduced the g-C_(3)N_(4) band gap from 2.7 to 2.54 eV,as evidenced by the UV–visible absorption spectra and the density functional theory results. The CO_(2) conversion performance of the catalysts was evaluated under visible light irradiation. The Pt/0.15 Sr-CN sample produced 48.55 and 74.54 μmol h-1 g-1 of CH_(4) and CO,respectively.These amounts are far greater than that produced by the Au/0.15 Sr-CN,0.15 Sr-CN,and CN samples. A high quantum e ciency of 2.92% is predicted for the Pt/0.15 Sr-CN sample. Further,the stability of the photocatalyst is confirmed via the photocatalytic recyclable test. The improved CO_(2) conversion performance of the catalyst is accredited to the promoted light absorption and remarkably enhanced charge separation via the Sr-incorporated mid gap states and the localized surface plasmon resonance e ect induced by noble metal nanoparticles.This work will provide a new approach for promoting the catalytic e ciency of g-C_(3)N_(4) for e cient solar fuel production.
文摘Additive manufacturing(AM)is an emerging customized three-dimensional(3D)functional product fabrication technology.It provides a higher degree of design freedom,reduces manufacturing steps,cost and production cycles.However,existing metallic component 3D printing techniques are mainly for the manufacture of single material components.With the increasing commercial applications of AM technologies,the need for 3D printing of more than one type of dissimilar materials in a single component increases.Therefore,investigations on multi-material AM(MMAM)emerge over the past decade.Lasers are currently widely used for the AM of metallic components where high temperatures are involved.Here we report the progress and trend in laser-based macro-and micro-scale AM of multiple metallic components.The methods covered in this paper include laser powder bed fusion,laser powder directed energy deposition,and laser-induced forward transfer for MMAM applications.The principles and process/material characteristics are described.Potential applications and challenges are discussed.Finally,future research directions and prospects are proposed.
基金financially supported by the project of Reconnaissance of Rare Metal Ores Including Rubidium in Huashi Village of Xinglong County, Hebei Province from the Hebei Bureau of Geology and Mineral Resources Exploration (grant No.2015017)
文摘Objective The Huashi Village in Xinglong County of Hebei Province is located in the Yanshan subsidence zone in the central eastern North China Plate, which is 137 km away from Beijing City (Fig. la). This area has undergone large -scale magmatic intrusion affected by the tectonic compression of the Pacific Plate in the Mesozoic (known as the Yanshanian movement) to form many alkaline rocks such as the Wulingshan rock mass. Previous studies have conducted petrological research and reconnaissance survey of rare metal ores in this area (Tian Shuzhang and Guo Zongshan, 1981; Xu Baoling et al., 1996). In 2016, the Qinhuangdao Mineral and Hydrology Engineering Geological Brigade of Hebei Bureau of Geology and Mineral Resources Exploration implemented the project of Reconnaissance of Rare Metal Ores Including Rubidium in Huashi Village of Xinglong County, Hebei Province, and discovered super-large rare metal deposits of rubidium and biobium in the Madi alkali feldspar granite bodies in the Huashi Village to achieve great breakthrough of rare metal ore prospecting.
基金GL and ELG acknowledge funding from the German Research Foundation in the framework of the priority program SPP 2006—Compositionally Complex Alloys—High Entropy Alloys,projects LA 3607/3-1 and GU 1075/12-1.EPG is supported by the U.S.Department of Energy,Office of Science,Basic Energy Sciences,Materials Sciences and Engineering Division.
文摘Progress in materials development is often paced by the time required to produce and evaluate a large number of alloys with different chemical compositions.This applies especially to refractory high-entropy alloys(RHEAs),which are difficult to synthesize and process by conventional methods.To evaluate a possible way to accelerate the process,high-throughput laser metal deposition was used in this work to prepare a quinary RHEA,TiZrNbHfTa,as well as its quaternary and ternary subsystems by in-situ alloying of elemental powders.Compositionally graded variants of the quinary RHEA were also analyzed.Our results show that the influence of various parameters such as powder shape and purity,alloy composition,and especially the solidification range,on the processability,microstructure,porosity,and mechanical properties can be investigated rapidly.The strength of these alloys was mainly affected by the oxygen and nitrogen contents of the starting powders,while substitutional solid solution strengthening played a minor role.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.61274039 and 51177175)the National Basic Research Program of China(Grant No.2011CB301903)+5 种基金the Ph.D.Programs Foundation of Ministry of Education of China(Grant No.20110171110021)the International Science and Technology Collaboration Program of China(Grant No.2012DFG52260)the International Science and Technology Collaboration Program of Guangdong Province,China(Grant No.2013B051000041)the Science and Technology Plan of Guangdong Province,China(Grant No.2013B010401013)the National High Technology Research and Development Program of China(Grant No.2014AA032606)the Opened Fund of the State Key Laboratory on Integrated Optoelectronics,China(Grant No.IOSKL2014KF17)
文摘In this work, the wafer bowing during growth can be in-situ measured by a reflectivity mapping method in the 3×2 Thomas Swan close coupled showerhead metal organic chemical vapor deposition(MOCVD) system. The reflectivity mapping method is usually used to measure the film thickness and growth rate. The wafer bowing caused by stresses(tensile and compressive) during the epitaxial growth leads to a temperature variation at different positions on the wafer, and the lower growth temperature leads to a faster growth rate and vice versa. Therefore, the wafer bowing can be measured by analyzing the discrepancy of growth rates at different positions on the wafer. Furthermore, the wafer bowings were confirmed by the ex-situ wafer bowing measurement. High-resistivity and low-resistivity Si substrates were used for epitaxial growth. In comparison with low-resistivity Si substrate, Ga N grown on high-resistivity substrate shows a larger wafer bowing caused by the highly compressive stress introduced by compositionally graded Al Ga N buffer layer. This transition of wafer bowing can be clearly in-situ measured by using the reflectivity mapping method.
文摘High-performance low-leakage-current A1GaN/GaN high electron mobility transistors (HEMTs) on silicon (111) sub- strates grown by metal organic chemical vapor deposition (MOCVD) with a novel partially Magnesium (Mg)-doped GaN buffer scheme have been fabricated successfully. The growth and DC results were compared between Mg-doped GaN buffer layer and a unintentionally onμe. A 1μ m gate-length transistor with Mg-doped buffer layer exhibited an OFF-state drain leakage current of 8.3 × 10-8 A/mm, to our best knowledge, which is the lowest value reported for MOCVD-grown A1GaN/GaN HEMTs on Si featuring the same dimension and structure. The RF characteristics of 0.25-μ m gate length T-shaped gate HEMTs were also investigated.
基金Supported by the Key Program of the National Natural Science Foundation of China under Grant No 61334009the National High Technology Research and Development Program of China under Grant No 2014AA032604
文摘CaN nanorods are successfully fabricated by adjusting the flow rate ratio of hydrogen (H2)/nitrogen (N2) and growth temperature of the selective area growth (SAG) method with metal organic chemical vapor deposition (MOCVD). The SAG template is obtained by nanospherical-lens photolithography. It is found that increasing the flow rate of 1-12 will change the CaN crystal shape from pyramid to vertical rod, while increasing the growth temperature will reduce the diameters of GaN rods to nanometer scale. Finally the CaN nanorods with smooth lateral surface and relatively good quality are obtained under the condition that the H2:N2 ratio is 1:1 and the growth temperature is 1030℃. The good crystal quality and orientation of GaN nanorods are confirmed by high resolution transmission electron microscopy. The cathodoluminescence spectrum suggests that the crystal and optical quality is also improved with increasing the temperature.
基金Funded by the National Natural Science Foundation of ChinaNational 863 Program of China(Nos.50872115and2009AA03Z203)
文摘CeO2 and Ce0.8M0.2O2-d films (M = Mn, Y, Gd, Sm, Nd and La) with (00l) preferred orientation have been prepared on biaxially textured Ni-W substrates by metal organic decomposition (MOD) method. The factors influencing the formation of cracks on the surface of these CeO2 and doped CeO2 films on Ni-W substrates were explored by X-ray diffraction (XRD), scanning electron microscopy (SEM) analysis, atomic force microscopy (AFM) and differential scanning calorimetry (DSC). The results indicate that many factors, such as the change of the ionic radii of doping cations, the transformation of crystal structure and the formation of oxygen vacancies in lattices at high annealing temperature, may be related to the formation of cracks on the surface of these films. However, the crack formation shows no dependence on the crystal lattice mismatch degree of the films with Ni-W substrates. Moreover, the suppression of surface cracks is related to the change of intrinsic elasticity of CeO2 film with doping of cations with a larger radius. SEM and AFM investigations of Ce0.8M0.2O2-d (M = Y, Gd, Sm, Nd and La) films reveal the dense, smooth and crack-free microstructure, and their lattice parameters match well with that of YBCO, illuminating that they are potentially suitable to be as buffer layer, especially as cap layer in multi-layer architecture of buffer layer for coated conductors.
文摘The 2205 duplex stainless + DH36 clad steel plate was welded by gas metal arc welding(GMAW), and the welding performance of the clad steel plate was investigated. The results show that the adaptability of the welding procedure for the base metal of carbon steel, the transition layer, and the cladding material is excellent. The test results indicate that the phase proportion and component dilution of the GMAW-welded joints of clad steel plate can be effectively controlled to yield joints with good mechanical properties and corrosion resistance.