Efficient quantum dot sensitized solar cells via improved loading amount management

High light-harvesting efficiency and low interfacial charge transfer loss are essential for the fabrication of high-efficiency quantum dot-based solar cells(QDSCs). Increasing the thickness of mesoporous TiO2films can improve the loading of pre-synthesized QDs on the film and enhance the absorbance of photoanode, but commonly accompanied by the increase in the unfavorable charge recombination due to prolonged electron transmission paths. Herein, we systematically studied the influence of the balance between QD loading and TiO2film thickness on the performance of QDSCs. It is found that the relative thin photoanode prepared by the cationic surfactant-assisted multiple deposition procedure has achieved a high QD loading which is comparable to that of the thick photoanode commonly used. Under AM 1.5G illumination, Zn–Cu–In–Se and Zn–Cu–In–S based QDSCs with optimized 11.8 μm photoanodes show the PCE of 10.03% and 8.53%, respectively, which are comparable to the corresponding highest PCE of Zn–Cu–In–Se and Zn–Cu–In–S QDSCs(9.74% and 8.75%) with over 25.0 μm photoanodes. Similarly, an impressive PCE of 6.14% was obtained for the CdSe based QDSCs with a 4.1 μm photoanode, which is slightly lower than the best PCE(7.05%)of reference CdSe QDSCs with 18.1 μm photoanode.

Dietary sodium acetate and sodium butyrate improve high-carbohydrate diet utilization by regulating gut microbiota, liver lipid metabolism, oxidative stress, and inflammation in largemouth bass(Micropterus salmoides)

Background Adequate level of carbohydrates in aquafeeds help to conserve protein and reduce cost. However, studies have indicated that high-carbohydrate(HC) diet disrupt the homeostasis of the gut–liver axis in largemouth bass, resulting in decreased intestinal acetate and butyrate level.Method Herein, we had concepted a set of feeding experiment to assess the effects of dietary sodium acetate(SA) and sodium butyrate(SB) on liver health and the intestinal microbiota in largemouth bass fed an HC diet. The experimental design comprised 5 isonitrogenous and isolipidic diets, including LC(9% starch), HC(18% starch), HCSA(18% starch;2 g/kg SA), HCSB(18% starch;2 g/kg SB), and HCSASB(18% starch;1 g/kg SA + 1 g/kg SB). Juvenile largemouth bass with an initial body weight of 7.00 ± 0.20 g were fed on these diets for 56 d.Results We found that dietary SA and SB reduced hepatic triglyceride accumulation by activating autophagy(ATG101, LC3B and TFEB), promoting lipolysis(CPT1α, HSL and AMPKα), and inhibiting adipogenesis(FAS, ACCA, SCD1 and PPARγ). In addition, SA and SB decreased oxidative stress in the liver(CAT, GPX1α and SOD1) by activating the Keap1-Nrf2 pathway. Meanwhile, SA and SB alleviated HC-induced inflammation by downregulating the expression of pro-inflammatory factors(IL-1β, COX2 and Hepcidin1) through the NF-κB pathway. Importantly, SA and SB increased the abundance of bacteria that produced acetic acid and butyrate(Clostridium_sensu_stricto_1). Combined with the KEGG analysis, the results showed that SA and SB enriched carbohydrate metabolism and amino acid metabolism pathways, thereby improving the utilization of carbohydrates. Pearson correlation analysis indicated that growth performance was closely related to hepatic lipid deposition, autophagy, antioxidant capacity, inflammation, and intestinal microbial composition.Conclusions In conclusion, dietary SA and SB can reduce hepatic lipid deposition;and alleviate oxidative stress and inflammation in largemouth bass fed on HC diet. These beneficial effects may be due to the altered composition of the gut microbiota caused by SA and SB. The improvement effects of SB were stronger than those associated with SA.

Geochemical fingerprints and hydrocarbon potential of Paleocene mudrocks in the Tano Basin, Ghana: insights from biomarkers and stable carbon isotopes

The Paleocene mudrocks in Ghana’s Tano Basin have received limited attention despite ongoing efforts to explore hydrocarbon resources.A thorough geochemical analysis is imperative to assess these mudrocks’petroleum generation potential and formulate effective exploration strategies.In this study,a comprehensive geochemical analysis was carried out on ten Paleocene rock cuttings extracted from TP-1,a discovery well within the Tano Basin.Various analytical techniques,including total organic carbon(TOC)analysis,Rock–Eval pyrolysis,gas chromatography-mass spectrometry,and isotope ratio-mass spectrometry,were employed to elucidate their hydrocar-bon potential and organic facies.Thefindings in this study were subsequently compared to existing geochemical data on Paleocene source rocks in the South Atlantic marginal basins.The results indicated that the Paleocene samples have TOC content ranging from 0.68 to 2.93 wt%.The prevalent kerogen types identified in these samples were Type Ⅱ and Type Ⅲ.Molecular and isotope data suggest that the organic matter found in the Paleocene mudrocks can be traced back to land plants and lower aquatic organisms.These mudrocks were deposited in a transi-tional environment withfluctuating water salinity,charac-terized by sub-oxic redox conditions.Maturity indices,both bulk and molecular,indicated a spectrum of maturity levels within the Paleocene mudrocks,spanning from immature to marginally mature,with increasing maturity observed with greater depth.In comparison,the organic composition and depositional environments of Paleocene source rocks in the Tano Basin closely resemble those found in the Niger Delta Basin,Douala,and Kribi-Campo Basins,the Kwanza Formation in Angola,and certain Brazilian marginal basins.However,it is worth noting that Paleocene source rocks in some of the basins,such as the Niger Delta and Brazilian marginal basins,exhibit rela-tively higher thermal maturity levels compared to those observed in the current Paleocene samples from the Tano Basin.In conclusion,the comprehensive geochemical analysis of Paleocene mudrocks within Ghana’s Tano Basin has unveiled their marginal hydrocarbon generation potential.The shared geochemical characteristics between the Paleocene mudrocks in the Tano Basin and those in the nearby South Atlantic marginal basins offer valuable insights into source rock quality,which is crucial for shaping future strategies in petroleum exploration in this region.

Lithium-Ion Charged Polymer Channels Flattening Lithium Metal Anode

The concentration difference in the near-surface region of lithium metal is the main cause of lithium dendrite growth.Resolving this issue will be key to achieving high-performance lithium metal batteries(LMBs).Herein,we construct a lithium nitrate(LiNO_(3))-implanted electroactiveβphase polyvinylidene fluoride-co-hexafluoropropylene(PVDF-HFP)crystalline polymorph layer(PHL).The electronegatively charged polymer chains attain lithium ions on the surface to form lithium-ion charged channels.These channels act as reservoirs to sustainably release Li ions to recompense the ionic flux of electrolytes,decreasing the growth of lithium dendrites.The stretched molecular channels can also accelerate the transport of Li ions.The combined effects enable a high Coulombic efficiency of 97.0%for 250 cycles in lithium(Li)||copper(Cu)cell and a stable symmetric plating/stripping behavior over 2000 h at 3 mA cm^(-2)with ultrahigh Li utilization of 50%.Furthermore,the full cell coupled with PHL-Cu@Li anode and Li Fe PO_(4) cathode exhibits long-term cycle stability with high-capacity retention of 95.9%after 900 cycles.Impressively,the full cell paired with LiNi_(0.87)Co_(0.1)Mn_(0.03)O_(2)maintains a discharge capacity of 170.0 mAh g^(-1)with a capacity retention of 84.3%after 100 cycles even under harsh condition of ultralow N/P ratio of 0.83.This facile strategy will widen the potential application of LiNO_(3)in ester-based electrolyte for practical high-voltage LMBs.

Review on laser directed energy deposited aluminum alloys

Lightweight aluminum(Al)alloys have been widely used in frontier fields like aerospace and automotive industries,which attracts great interest in additive manufacturing(AM)to process high-value Al parts.As a mainstream AM technique,laser-directed energy deposition(LDED)shows good scalability to meet the requirements for large-format component manufacturing and repair.However,LDED Al alloys are highly challenging due to their inherent poor printability(e.g.low laser absorption,high oxidation sensitivity and cracking tendency).To further promote the development of LDED high-performance Al alloys,this review offers a deep understanding of the challenges and strategies to improve printability in LDED Al alloys.The porosity,cracking,distortion,inclusions,element evaporation and resultant inferior mechanical properties(worse than laser powder bed fusion)are the key challenges in LDED Al alloys.Processing parameter optimizations,in-situ alloy design,reinforcing particle addition and field assistance are the efficient approaches to improving the printability and performance of LDED Al alloys.The underlying correlations between processes,alloy innovation,characteristic microstructures,and achievable performances in LDED Al alloys are discussed.The benchmark mechanical properties and primary strengthening mechanism of LDED Al alloys are summarized.This review aims to provide a critical and in-depth evaluation of current progress in LDED Al alloys.Future opportunities and perspectives in LDED high-performance Al alloys are also outlined.

Tumor deposits in axillary adipose tissue in patients with breast cancer:Do they matter?

Tumor deposits(TDs)are defined as discrete,irregular clusters of tumor cells lying in the soft tissue adjacent to but separate from the primary tumor,and are usually found in the lymphatic drainage area of the primary tumor.By definition,no residual lymph node structure should be identified in these tumor masses.At present,TDs are mainly reported in colorectal cancer,with a few reports in gastric cancer.There are very few reports on breast cancer(BC).For TDs,current dominant theories suggest that these are the result of lymph node metastasis of the tumor with complete destruction of the lymph nodes by the tumor tissue.Even some pathologists classify a TD as two lymph node metastases for calculation.Some pathologists also believe that TDs belong to the category of disseminated metastasis.Therefore,regardless of the origin,TDs are an indicator of poor prognosis.Moreover,for BC,sentinel lymph node biopsy is generally used at present.Whether radical axillary lymph node dissection should be adopted for BC with TDs in axillary lymph nodes is still inconclusive.The present commentary of this clinical issue has certain guiding significance.It is aimed to increase the awareness of the scientific community towards this under-recognized problem in BC pathology.

Origin of the Yueguang gold deposit in Xinhua, Hunan Province, South China: insights from fl uid inclusion and hydrogen–oxygen stable isotope analysis

The Yueguang gold deposit is located in Fengjia,Xinhua County,Hunan Province,South China.It represents a recently discovered small-scale gold deposit situated in the southwestern region of the Jiangnan Orogenic Belt,west of the Baimashan granitic batholith.In order to discern the characteristics of the ore-formingfluids,the underlying mineralization processes,and establish a foundation for the origin of the Yueguang gold depositfluid inclusion micro-thermometry,as well as quartz hydrogen and oxygen isotope analysis,have been carried out on samples obtained from various stages of mineralization.The hydrothermal miner-alization stages within the Yueguang gold deposit can be categorized into three stages:(i)the barren,pre-ore quartz-pyrite stage(Stage Ⅰ),the quartz-pyrite-gold stage(Stage Ⅱ),and the post-ore quartz-carbonate stage(Stage Ⅲ),with the second stage being the main mineralization stage.Thefluid inclusions identified in samples from the main min-eralization stage can predominantly be described with the NaCl–H_(2)O and CO_(2)–NaCl–H_(2)O systems.These inclusions display homogenization temperatures ranging from 158.8 to 334.9℃,and thefluid salinity ranges from 0.3%to 4.0%(wt.%NaCl equiv.).Laser Raman spectroscopy analysis of individual inclusions further reveals the presence of gas-phases such as CO_(2),CH_(4),and N_(2).Isotopic analysis indicatesδ^(18)Ofluid values ranging from 3.95 to 6.7‰ and δDH_(2)O values ranging from-71.9 to-55.7‰.These results indi-cate that the ore-formingfluid of the Yueguang gold deposit belongs to metamorphic hydrothermalfluids of middle-low temperature and low salinity.In the process of ore formation,gold is transported in the form of Au(HS)2-complexes,with gold deposition being driven byfluid immiscibility.Therefore,the Yueguang gold deposit is categorized as an orogenic gold deposit dominated by metamorphic hydrother-malfluid.It may become a new target for gold exploration in the Baimashan region,central Hunan Province.

Relationship between hydrogenation degree and pyrolysis performance of jet fuel

Understanding the relationship between the chemical composition and pyrolysis performance of endothermic hydrocarbon fuel(EHF) is of great significance for the design and optimization of advanced EHFs. In this work, the effect of deep hydrogenation on the pyrolysis of commercial RP-3 is investigated.Fuels with different hydrogenation degrees were obtained by the partially and completely catalytic hydrogenation and their pyrolysis performances were investigated using an apparatus equipped with an electrically heated tubular reactor. The results show that with the increase of hydrogenation degree, fuel conversion almost remains constant during the pyrolysis process(500-650°C, 4 MPa);however, the heat sink increases slightly, and the anti-coking performance significantly improves, which are highly related to their H/C ratios. Detailed characterisations reveal that the difference of the pyrolysis performance can be ascribed to the content of aromatics and cycloalkanes: the former are prone to initiate secondary reactions to form coking precursors, while the latter could act as the hydrogen donor and release hydrogen, which will terminate the radical propagation reactions and suppress the coke deposition. This work should provide the guidance for upgrading EHFs by modulating the composition of EHFs.

Depositional process of hyperpycnal flow deposits:A case study on Lower Cretaceous Sangyuan outcrop in the Luanping Basin,Northeast China

Sedimentary process research is of great significance for understanding the distribution and characteristics of sediments.Through the detailed observation and measurement of the Sangyuan outcrop in Luanping Basin,this paper studies the depositional process of the hyperpycnal flow deposits,and divides their depositional process into three phases,namely,acceleration,erosion and deceleration.In the acceleration phase,hyperpycnal flow begins to enter the basin nearby,and then speeds up gradually.Deposits developed in the acceleration phase are reverse.In addition,the original deposits become unstable and are taken away by hyperpycnal flows under the eroding force.As a result,there are a lot of mixture of red mud pebbles outside the basin and gray mud pebbles within the basin.In the erosion phase,the reverse deposits are eroded and become thinner or even disappear.Therefore,no reverse grading characteristic is found in the proximal major channel that is closer to the source,but it is still preserved in the middle branch channel that is far from the source.After entering the deceleration phase,normally grading deposits appear and cover previous deposits.The final deposits in the basin are special.Some are reverse,and others are normal.They are superimposed with each other under the action of hyperpycnal flow.The analysis of the Sangyuan outcrop demonstrates the sedimentary process and distribution of hyperpycnites,and reasonably explain the sedimentary characteristics of hyperpycnites.It is helpful to the prediction of oil and gas exploration targets in gravity flow deposits.

Towards the insights into the deactivation behavior of acetylene hydrogenation catalyst

A series of model catalysts were obtained by treating commercial fresh and spent catalysts unloaded from the factory with different methods, including green oil dipping, extraction and high-temperature regeneration;finally, the deactivation behavior of the commercial catalyst for acetylene hydrogenation were studied. The influence of various possible deactivation factors on the catalytic performance was elucidated via detailed structural characterization, surface composition analysis, and activity evaluation.The results showed that green oil, carbon deposit and sintering of active metal were the main reasons for deactivation, among which green oil and carbon deposit led to rapid deactivation, while the activity could be recovered after regeneration by high-temperature calcination. The sintering of active metal components was attributed to the high-temperature regeneration in hydrothermal conditions, which was slow but irreversible and accounted for permanent deactivation. Thus, optimizing the regeneration is expected to extend the service life of the commercial catalyst.

Geochemistry and depositional environment of fuchsite quartzites from Sargur Group,western Dharwar Craton,India

Meso-Neoarchean fuchsite quartzites are present in different stratigraphic positions of Dharwar Craton including the oldest(~3.3 Ga)Sargur Group of western Dharwar Craton.The present study deals with the petro-graphic and geochemical characteristics of the fuchsite quartzites from the Ghattihosahalli belt to evaluate their genesis,depositional setting and the enigma involved in the ancient sedimentation history.Their major mineral assemblages include quartz,fuchsite,and feldspars along with accessory kyanite and rutile.The geochemical com-positions are characterized by high SiO_(2),Al_(2)O_(3),low MgO,CaO,strongly enriched Cr(1326–6899 ppm),Ba(1165–3653 ppm),Sr(46–210 ppm),V(107–868 ppm)and Zn(11–158 ppm)contents compared to the upper continental crust(UCC).The UCC normalized rare earth element(REE)patterns are characterized by depleted light REE[(La/Sm)UCC=0.33–0.95]compared to heavy REE[(Gd/Yb)_(UCC)=0.42–1.65]with conspicuous positive Eu-anomalies(Eu/Eu^(*)=1.35–18.27)characteristic of hydrothermal solutions evidenced through the interlayered barites.The overall major and trace element systematics reflect a combined mafic-felsic provenance and suggest their deposition at a passive continental margin environ-ment.The comprehensivefield,petrographic,and geo-chemical studies indicate that these quartzites are infiltrated by Cr-richfluids released during high-grade metamorphism of associated ultramafic rocks.The Sargur and the subse-quent Dharwar orogeny amalgamated diverse lithounits from different tectonic settings,possibly leading to the release of Cr-richfluids and the formation of fuchsite quartzite during or after the orogeny.Thesefindings sug-gest a pre-existing stable crust prior to the Sargur Group and the link between orogenic events and various mineral deposits in the Dharwar Craton.

Unveiling the emerging role of curcumin to alleviate ochratoxin A-induced muscle toxicity in grass carp(Ctenopharyngodon idella):in vitro and in vivo studies

Background Ochratoxin A(OTA),a globally abundant and extremely hazardous pollutant,is a significant source of contamination in aquafeeds and is responsible for severe food pollution.The developmental toxicity of OTA and the potential relieving strategy of natural products remain unclear.This study screened the substance curcumin(Cur),which had the best effect in alleviating OTA inhibition of myoblast proliferation,from 96 natural products and investigated its effect and mechanism in reducing OTA myotoxicity in vivo and in vitro.Methods A total of 720 healthy juvenile grass carp,with an initial average body weight of 11.06±0.05 g,were randomly assigned into 4 groups:the control group(without OTA and Cur),1.2 mg/kg OTA group,400 mg/kg Cur group,and 1.2 mg/kg OTA+400 mg/kg Cur group.Each treatment consisted of 3 replicates(180 fish)for 60 d.Results Firstly,we cultured,purified,and identified myoblasts using the tissue block culture method.Through preliminary screening and re-screening of 96 substances,we examined cell proliferation-related indicators such as cell viability and ultimately found that Cur had the best effect.Secondly,Cur could alleviate OTA-inhibited myoblast differentiation and myofibrillar development-related proteins(Myo G and MYHC)in vivo and in vitro and improve the growth performance of grass carp.Then,Cur could also promote the expression of OTA-inhibited protein synthesis-related proteins(S6K1 and TOR),which was related to the activation of the AKT/TOR signaling pathway.Finally,Cur could downregulate the expression of OTA-enhanced protein degradation-related genes(murf1,foxo3a,and ub),which was related to the inhibition of the Fox O3a signaling pathway.Conclusions In summary,our data demonstrated the effectiveness of Cur in alleviating OTA myotoxicity in vivo and in vitro.This study confirms the rapidity,feasibility,and effectiveness of establishing a natural product screening method targeting myoblasts to alleviate fungal toxin toxicity.

Unveiling Nb-Ta mineralization processes:Insight from quartz textural and chemical characteristics in the Songshugang deposit,Jiangxi Province,South China

The Songshugang deposit is a large Ta-Nb deposit in South China,with Ta-Nb mineralization associated genetically with the granite and pegmatite.A diversity of quartz from topaz-albite granite,quartz-mica pegmatite,quartz-feldspar pegmatite,and quartz-fluorite pegmatite at Songshugang was studied by CL and LA-ICP-MS in order to constrain enrichment mechanisms of Nb and Ta and to find geochemical indicators of quartz for rare metal deposits.Cathodoluminescence image illuminates a canvas of complexity,the quartz from topaz-albite granite,quartz-mica pegmatite,quartz-feldspar pegmatite,and quartz-fluorite pegmatite,exhibits numerous dark CL streaks,patches,and a series of healed fractures.These textures suggest that the rocks were fractured because of deep crustal pressure,and underwent later hydrothermal metasomatism and quartz filling.The quartz from quartz-fluorite pegmatite present limited patches or fractures but distinct growth bands,indicating that the melt fluid composition during the formation of quartz at this stage varies greatly and is less aff ected by mechanical fragmentation.The LA-ICP-MS analysis of quartz shows that there is a positive correlation between Al and Li in the quartz from topaz-albite granite,quartz-mica pegmatite,quartz-feldspar pegmatite,to quartz-fluorite pegmatite,indicating that Al mainly enters the quartz lattice through charge compensation substitution mechanism with Li.However,our data deviate from the theoretical Li:Al mass ratio of~1:3.89 in quartz,indicating that there may be competition between H^(+)and Li in a water-rich magmatic environment.The quartz from topaz-albite granite is enriched in K and Na elements,and the quartz from quartz-fluorite pegmatite is enriched in fluorite with a low Ca content in quartz,further elucidating that these rocks were subjected to hydrothermal metasomatism.From topaz-albitite granite to quartz-fluorite pegmatite,Al,Li and Ge content and Al/Ti,Ge/Ti,Sb/Ti ratios in quartz gradually increased,but Ti content gradually decreased,reflecting the high evolution of magma,which can enrich rare metal elements.Based on the characteristics of quartz CL textures and trace elements in topaz-albite granite,quartz-mica pegmatite,quartz-feldspar pegmatite,and quartz-fluorite pegmatite,combined with the albitization and K-feldspathization of rocks,it is suggested that the Nb-Ta mineralization in Songshugang may be influenced by the combined action of magmatic crystallization differentiation and fluid metasomatism.By comparing the quartz in the Songshugang pluton with the quartz in the granite type and pegmatite type rare metal deposits recognized in the world,the Songshugang pegmatite share similarities with the LCT-type pegmatite.Combined with previous studies,the Ge/Ti>0.1 and Ti<10 ppm,as well as Al,Li,Ge,Sb,K,Na contents and Al/Ti,Sb/Ti ratios in quartz have the potential to be a powerful exploration marker for identifying granite-like pegmatitic Nb-Ta deposits in other places.

Printability disparities in heterogeneous material combinations via laser directed energy deposition:a comparative study

Additive manufacturing provides achievability for the fabrication of bimetallic and multi-material structures;however,the material compatibility and bondability directly affect the parts’formability and final quality.It is essential to understand the underlying printability of different material combinations based on an adapted process.Here,the printability disparities of two common and attractive material combinations(nickel-and iron-based alloys)are evaluated at the macro and micro levels via laser directed energy deposition(DED).The deposition processes were captured using in situ high-speed imaging,and the dissimilarities in melt pool features and track morphology were quantitatively investigated within specific process windows.Moreover,the microstructure diversity of the tracks and blocks processed with varied material pairs was comparatively elaborated and,complemented with the informative multi-physics modeling,the presented non-uniformity in mechanical properties(microhardness)among the heterogeneous material pairs was rationalized.The differences in melt flow induced by the unlike thermophysical properties of the material pairs and the resulting element intermixing and localized re-alloying during solidification dominate the presented dissimilarity in printability among the material combinations.This work provides an in-depth understanding of the phenomenological differences in the deposition of dissimilar materials and aims to guide more reliable DED forming of bimetallic parts.

Atomic layer deposition in advanced display technologies:from photoluminescence to encapsulation

Driven by the growing demand for next-generation displays,the development of advanced luminescent materials with exceptional photoelectric properties is rapidly accelerating,with such materials including quantum dots and phosphors,etc.Nevertheless,the primary challenge preventing the practical application of these luminescent materials lies in meeting the required durability standards.Atomic layer deposition(ALD)has,therefore,been employed to stabilize luminescent materials,and as a result,flexible display devices have been fabricated through material modification,surface and interface engineering,encapsulation,cross-scale manufacturing,and simulations.In addition,the appropriate equipment has been developed for both spatial ALD and fluidized ALD to satisfy the low-cost,high-efficiency,and high-reliability manufacturing requirements.This strategic approach establishes the groundwork for the development of ultra-stable luminescent materials,highly efficient light-emitting diodes(LEDs),and thin-film packaging.Ultimately,this significantly enhances their potential applicability in LED illumination and backlighted displays,marking a notable advancement in the display industry.

Geology and Geochemistry of K-feldspar Veins in Lamprophyre at the Zhenyuan Gold Deposit,Yunnan,Southwest China:Implications for Gold Mineralization

Lamprophyres typically appear in hydrothermal gold deposits.The relationship between lamprophyres and gold deposits is investigated widely.Some researchers suggest that the emplacement of lamprophyres triggers gold mineralization,whereas others hypothesize that the formation of lamprophyres increases the fertility of mantle sources and ore-forming fluids.K-feldspar veins,with ages between those of lamprophyres and gold deposits,appear in lamprophyres in Zhenyuan.Therefore,K-feldspar veins are ideal for investigating the relationship between lamprophyres and gold deposits.Phlogopite in K-feldspar veins has lower Mg#,Ni,and Cr contents and higher TiO2,Li,Ba,Sr,Sc,Zr,Nb,and Cs contents than phlogopite in lamprophyres.The in-situ Sr isotopic values of apatites(0.7063–0.7066)in K-feldspar veins are within the range for apatites(0.7064–0.7078)from lamprophyres.High large-ion lithophile element concentrations and low Nb and Ta concentrations in phlogopite from lamprophyres,in addition to high(87Sr/86Sr)i values of apatite(0.7064–0.7078),indicate that the magma parental to these phlogopite and apatite crystals is derived from an enriched mantle.Kfeldspar veins are genetically correlated with lamprophyres,whereas sulfide mineral assemblage and trace element compositions of pyrite in K-feldspar veins suggest that K-feldspar veins in lamprophyres are not directly related to gold mineralization of the Zhenyuan deposit.

Trace elements in magmatic and hydrothermal quartz:Implications on the genesis of the Xingluokeng Tungsten Deposit,South China

The Xingluokeng deposit is the largest gran-ite-related tungsten deposit within the Wuyi metallogenic belt in South China.The Xingluokeng intrusion primarily consists of porphyritic biotite granite,biotite granite,andfine-grained granite.The deposit is represented by veinlet-disseminated mineralization with K-feldspathization and biotitization,alongside quartz-vein mineralization with gre-isenization and sericitization.This study investigates in-situ analyses of quartz compositions from both the intrusion and hydrothermal veinlets and veins.Trace element correlations indicate that trivalent Al^(3+)and Fe^(3+)replace Si^(4+)within the quartz lattice,with monovalent cations(such as Li^(+),Na^(+),and K^(+))primarily serving as charge compensators.Low Ge/Al ratios(<0.013)of quartz from granites suggest a mag-matic origin.The low Al/Ti and Ge/Ti ratios,accompanied by high Ti contents in quartz,suggest that the porphyritic biotite granite and biotite granite are characterized by rela-tively low levels of differentiation and high crystallization temperatures.In contrast,thefine-grained granite exhibits a higher degree of fractionation,lower crystallization tem-peratures,and a closer association with tungsten miner-alization.Ti contents in quartz from quartz veins indicate Qz-Ⅰformed at temperatures above 400°C,while Qz-Ⅱto Qz-Ⅴformed at temperatures below 350°C.Variations in different generations of quartz,as indicated by Al content and(Al+Fe)/(Li+Na+K)ratio,suggest that Qz-Ⅰprecipi-tated from a less acidicfluid with a stable pH,whereas Qz-Ⅱto Qz-Ⅴoriginated from a more acidicfluid with notable pH variations.Consequently,alkaline alteration and acidic alteration supplied the essential Ca and Fe for the precipita-tion of scheelite and wolframite,respectively,highlighting a critical mechanism in tungsten mineralization at the Xin-gluokeng deposit.

New insights into the deposition of natural gas hydrate on pipeline surfaces:A molecular dynamics simulation study

Natural gas hydrate(NGH)can cause pipeline blockages during the transportation of oil and gas under high pressures and low temperatures.Reducing hydrate adhesion on pipelines is viewed as an efficient way to prevent NGH blockages.Previous studies suggested the water film can greatly increase hydrate adhesion in gas-dominant system.Herein,by performing the molecular dynamics simulations,we find in water-dominant system,the water film plays different roles in hydrate deposition on Fe and its corrosion surfaces.Specifically,due to the strong affinity of water on Fe surface,the deposited hydrate cannot convert the adsorbed water into hydrate,thus,a water film exists.As water affinities decrease(Fe>Fe_(2)O_(3)>FeO>Fe_(3)O_(4)),adsorbed water would convert to amorphous hydrate on Fe_(2)O_(3)and form the ordered hydrate on FeO and Fe_(3)O_(4)after hydrate deposition.While absorbed water film converts to amorphous or to hydrate,the adhesion strength of hydrate continuously increases(Fe<Fe_(2)O_(3)<FeO<Fe_(3)O_(4)).This is because the detachment of deposited hydrate prefers to occur at soft region of liquid layer,the process of which becomes harder as liquid layer vanishes.As a result,contrary to gas-dominant system,the water film plays the weakening roles on hydrate adhesion in water-dominant system.Overall,our results can help to better understand the hydrate deposition mechanisms on Fe and its corrosion surfaces and suggest hydrate deposition can be adjusted by changing water affinities on pipeline surfaces.

Evolution of tectonic landscapes and deformation in the southeast Kumaun and western Nepal Himalaya

The area of the present investigation’s expanse constitutes the southernmost extent of the southeast Kumaun Himalaya and western Nepal Himalaya.Multidisciplinary approaches have been employed to understand the landforms associated with tectonic deformation,through detailed field investigation supplemented by the geodetic,chronological,and morphometric database.The morphogenic expressions of the Main Boundary Thrust(MBT)are reflected in the form of~25 km long E-W trending north dipping fault scarp.The deformation along the strike length of the Himalayan Frontal Thrust(HFT)is noticed in the form of uplifted and incised fill terraces,and strath terraces.The deformation within the fluvial sequences in the study area can be visualized in the form of sheared boulders and pebbles,tilted and faulted terrace deposits.Furthermore,the chronological data of fluvial landforms in the study area suggests two major phases of tectonic deformations that have occurred around 58.7±10.8 ka and 3.88±0.4 ka.The chronology of late-Quaternary landforms advocates that the initial stage of aggradations in the Himalayan foothills commenced around 75.1±0.58 ka.The aggradational landforms resulted from the diverse depositional regime as evident from the nature of the sediment sequences from clasts dominated to thick mud sequences.The rate of deformation in the southeastern Kumaun and western Nepal Himalaya is±7 mm/yr,as per the data obtained from the Persistent Scatterer Interferometric Synthetic Aperture Radar(PSInSAR).The landform deformation pattern,phase of incision and aggradation,frequent occurrence of landslides,and recent past earthquake activity within the wide zone of the HFT,the MBT,and Ramgarh Thrust suggests that the southernmost front of the Kumaun Himalaya is active and has potential for future geohazard.The foothill zone of Himalayan towns are actively growing in terms of population and infrastructural development.Therefore,such intradisciplinary studies for tectonically active regions are needed for future infrastructural development.

Grain size and surface micro-texture characteristics and their paleoenvironmental significance of Holocene sediment in southern margin of the Gurbantunggut Desert,China

The southern margin of the Gurbantunggut Desert,China,is characterized by alternating layers of aeolian and alluvial deposits.Investigating the characteristics of arenaceous sediment in this area is of significant importance for understanding the interactive processes of wind and water forces,as well as the provenance of sediment.However,there are relatively few investigations on the characteristics of such sediment at present.In this study,we researched three aeolian-alluvial interactive stratigraphic profiles and different types of surface sediment on the desert-oasis transitional zone of southern margin of the Gurbantunggut Desert.Based on the optically stimulated luminescence(OSL)dating of aeolian sand and analyses of quartz sand grain size and surface micro-texture,we explored the aeolian-alluvial environmental change at southern margin of the desert in Holocene,as well as the provenance of sediment.The results indicated that the grain size characteristics of different types of sediment in the stratigraphic profiles were similar to those of modern dune sand,interdune sand,muddy desert surface soil,and riverbed sand.Their frequency curves were unimodal or bimodal,and cumulative probability curves were two-segment or three-segment,mainly composed of suspension load and saltation load.The quartz sand in the sediment at southern margin of the desert had undergone alternating transformation of various exogenic forces,with short transportation distance and time,and sedimentary environment was relatively humid.In Holocene,southern margin of the desert primarily featured braided river deposits,and during intermittent period of river activity,there were also aeolian deposits such as sand sheet deposits,stabilized dune deposits,and mobile dune deposits.The provenance for Holocene alluvial deposits at southern margin of the desert remains relatively constant,with the debris of the Tianshan Mountains being the primary provenance.Aeolian sand is mainly near-source recharge,which is formed by in situ deposition of fluvial or lacustrine materials in southern margin of the desert transported by wind erosion,and its provenance was still the weathered debris of the Tianshan Mountains.In addition,the sand in interior of the desert may be transported by northwest wind in desert-scale,thus affecting the development of dunes in southern margin of the desert.The results of this study provide a reference for understanding the composition and provenance changes of desert sand in the context of global climate change.