期刊文献+
共找到87篇文章
< 1 2 5 >
每页显示 20 50 100
Effects of Deposition Models on Deposition and Performance Deterioration in Axial Compressor Cascade 被引量:2
1
作者 贾会霞 席光 +1 位作者 高丽敏 闻苏平 《Chinese Journal of Aeronautics》 SCIE EI CAS CSCD 2005年第1期20-24,共5页
A new particle deposition model, namely partial deposition model, is developed in order to improve the accuracy of prediction to particle deposition. Concepts of critical velocity and critical angle are proposed and u... A new particle deposition model, namely partial deposition model, is developed in order to improve the accuracy of prediction to particle deposition. Concepts of critical velocity and critical angle are proposed and used to determine whether particles are deposited or not. The comparison of numerical results calculated by partial deposition model and existing deposition model shows that the deposition distribution obtained by partial deposition model is more reasonable. Based on the predicted deposition results, the change of total pressure loss coefficient with operating time and the distribution of pressure coefficients on blade surface after 500 hours are predicted by using partial deposition model. 展开更多
关键词 axial compressors cascade partial deposition model performance deterioration
下载PDF
Depositional model of the Member Deng-2 marginal microbial mound-bank complex of the Dengying Formation in the southwestern Sichuan Basin, SW China: Implications for the Ediacaran microbial mound construction and hydrocarbon exploration
2
作者 Jin-Min Song Xin Jin +10 位作者 Zhong Luo Shu-Gen Liu Shao-Bo Liu Xing-Zhi Ma Zhi-Wu Li Xue-Song Lu Ling-Li Zhao Ke-Ran Li Jia-Xin Ren Li-Zhou Tian Hao-Shuang Deng 《Petroleum Science》 SCIE EI CAS CSCD 2024年第2期806-822,共17页
Recent advances in hydrocarbon exploration have been made in the Member Deng-2 marginal microbial mound-bank complex reservoirs of the Dengying Formation in the western Sichuan Basin, SW China,where the depositional p... Recent advances in hydrocarbon exploration have been made in the Member Deng-2 marginal microbial mound-bank complex reservoirs of the Dengying Formation in the western Sichuan Basin, SW China,where the depositional process is regarded confusing. The microfacies, construction types, and depositional model of the Member Deng-2 marginal microbial mound-bank complex have been investigated using unmanned aerial vehicle photography, outcrop section investigation, thin section identification,and seismic reflections in the southwestern Sichuan Basin. The microbialite lithologic textures in this region include thrombolite, dendrolite, stromatolite, fenestral stromatolite, spongiostromata stone,oncolite, aggregated grainstone, and botryoidal grapestone. Based on the comprehensive analysis of“depositional fabrics-lithology-microfacies”, an association between a fore mound, mound framework,and back mound subfacies has been proposed based on water depth, current direction, energy level and lithologic assemblages. The microfacies of the mound base, mound core, mound flank, mound cap, and mound flat could be recognized among the mound framework subfacies. Two construction types of marginal microbial mound-bank complex have been determined based on deposition location, mound scale, migration direction, and sedimentary facies association. Type Jinkouhe microbial mound constructions(TJMMCs) develop along the windward margin owing to their proximity to the seaward subfacies fore mound, with a northeastwardly migrated microbial mound on top of the mud mound,exhibiting the characteristics of large-sized mounds and small-sized banks in the surrounding area. Type E'bian microbial mound constructions(TEMMCs) primarily occur on the leeward margin, resulting from the presence of onshore back mound subfacies, with the smaller southwestward migrated microbial mounds existing on a thicker microbial flat. The platform margin microbial mound depositional model can be correlated with certain lateral comparison profile and seismic reflection structures in the 2D seismic section, which can provide references for future worldwide exploration. Microbial mounds with larger buildups and thicker vertical reservoirs are typically targeted on the windward margin, while small-sized microbial mounds and flats with better lateral connections are typically focused on the leeward margin. 展开更多
关键词 Sichuan Basin The Member Deng-2 Marginal microbial mound-bank complex depositional model Exploration implications
下载PDF
Numerical simulation and printability analysis of fused deposition modeling with dual-temperature control 被引量:1
3
作者 Xiaodan Huo Bin Zhang +2 位作者 Qianglong Han Yong Huang Jun Yin 《Bio-Design and Manufacturing》 SCIE EI CAS CSCD 2023年第2期174-188,共15页
Ideal tissue engineering scaffolds need interconnected pores and high porosity to enable cell survival,migration,proliferation,and differentiation.However,obtaining a high-resolution structure is difficult with tradit... Ideal tissue engineering scaffolds need interconnected pores and high porosity to enable cell survival,migration,proliferation,and differentiation.However,obtaining a high-resolution structure is difficult with traditional one-temperature control fused deposition modeling(FDM).In this study,we propose a dual-temperature control method to improve printability.A numerical model is developed in which the viscosity is a function of temperature and shear rate to study the influence of two different temperature control modes.Quantitative tests are used to assess filament formation and shape fidelity,including one-dimensional filament printing,deposition at corners,fusion,and collapse.By using dual-temperature control,the width of the deposited poly(ε-caprolactone)filament is reduced to 50μm.The comparative results of both the experimental method and numerical simulation suggest that the dual-temperature control FDM can manufacture spatially arranged constructs and presents a promising application in tissue engineering。 展开更多
关键词 Fused deposition modeling(FDM) Dual-temperature control Filament deposition Printing resolution VISCOSITY
下载PDF
Multi-Objective Optimization of Fused Deposition Modeling for Mechanical Properties of Biopolymer Parts Using the Grey-Taguchi Method
4
作者 Kapil Kumar Hari Singh 《Chinese Journal of Mechanical Engineering》 SCIE EI CAS CSCD 2023年第1期51-64,共14页
The urgent need to develop customized functional products only possible by 3D printing had realized when faced with the unavailability of medical devices like surgical instruments during the coronavirus-19 disease and... The urgent need to develop customized functional products only possible by 3D printing had realized when faced with the unavailability of medical devices like surgical instruments during the coronavirus-19 disease and the ondemand necessity to perform surgery during space missions.Biopolymers have recently been the most appropriate option for fabricating surgical instruments via 3D printing in terms of cheaper and faster processing.Among all 3D printing techniques,fused deposition modelling(FDM)is a low-cost and more rapid printing technique.This article proposes the fabrication of surgical instruments,namely,forceps and hemostat using the fused deposition modeling(FDM)process.Excellent mechanical properties are the only indicator to judge the quality of the functional parts.The mechanical properties of FDM-processed parts depend on various process parameters.These parameters are layer height,infill pattern,top/bottom pattern,number of top/bottom layers,infill density,flow,number of shells,printing temperature,build plate temperature,printing speed,and fan speed.Tensile strength and modulus of elasticity are chosen as evaluation indexes to ascertain the mechanical properties of polylactic acid(PLA)parts printed by FDM.The experiments have performed through Taguchi’s L27orthogonal array(OA).Variance analysis(ANOVA)ascertains the significance of the process parameters and their percent contributions to the evaluation indexes.Finally,as a multiobjective optimization technique,grey relational analysis(GRA)obtains an optimal set of FDM process parameters to fabricate the best parts with comprehensive mechanical properties.Scanning electron microscopy(SEM)examines the types of defects and strong bonding between rasters.The proposed research ensures the successful fabrication of functional surgical tools with substantial ultimate tensile strength(42.6 MPa)and modulus of elasticity(3274 MPa). 展开更多
关键词 Fused deposition modeling Mechanical properties Taguchi method ANOVA Grey relational analysis SEM
下载PDF
Effect of Fibre Size on Mechanical Properties and Surface Roughness of PLA Composites by Using Fused Deposition Modelling (FDM)
5
作者 Aida Haryati Jamadi Nadlene Razali +1 位作者 Sivakumar Dhar Malingam Mastura Mohammad Taha 《Journal of Renewable Materials》 EI 2023年第8期3261-3276,共16页
Naturalfibre as a reinforcing agent has been widely used in many industrial applications.Nevertheless,several factors need to be considered,such as the size and weight percentage of thefibre used in binding.Using fused ... Naturalfibre as a reinforcing agent has been widely used in many industrial applications.Nevertheless,several factors need to be considered,such as the size and weight percentage of thefibre used in binding.Using fused deposition modelling(FDM),this factor was investigated by varying the size of naturalfibre as the responding variable with afixed weight percentage of kenaffibre.The process of modifying the naturalfibre in terms of size might increase the dispersion of kenaffibre in the polymer matrix and increase the adhesion bonding between thefibre and matrix of composites,subsequently improving the interfacial bonding between these two phases.In this paper,the effect offibre size was evaluated by performing the mechanical test,Scanning Electron Micrograph(SEM)to observe the morphology of the composites,and also by surface analysis.The surface roughness was visualised using a 3D profilometer and thefigure was illustrated as colour shading in the image.The composite withfibre size≤100μm displayed better tensile andflexural strength,compared to other sizes.In conclusion,by reducing the size of thefibre,the composites could develop high strength performance for industrial applications. 展开更多
关键词 Fibre size mechanical properties fused deposition modelling(FDM) surface analysis
下载PDF
DECISION-MAKING OF SLICING SCHEME IN FUSED DEPOSITION MODELING PROCESS BASED ON ANALYTICAL HIERARCHICAL PROCESS 被引量:6
6
作者 张剑峰 彭安华 《Transactions of Nanjing University of Aeronautics and Astronautics》 EI 2010年第2期125-130,共6页
Based on analyzing the influences of a slicing scheme on stair-stepping effect, supporting structure, efficiency and deformation, etc. , analytical hierarchical process (AHP) combining with fuzzy synthetic evaluatio... Based on analyzing the influences of a slicing scheme on stair-stepping effect, supporting structure, efficiency and deformation, etc. , analytical hierarchical process (AHP) combining with fuzzy synthetic evaluation is introduced to make decision in slicing schemes for a processing part. The application in determining the slicing scheme for a computer mouse during prototyping shows that the method increases the rationality during decision- making and improves quality and efficiency for the prototyping part. 展开更多
关键词 DECISION-MAKING fused deposition modeling (FDM) analytical hierarchical process (AHP) slicing scheme
下载PDF
Sedimentary characteristics and depositional model of a Paleocene-Eocene salt lake in the Jiangling Depression,China 被引量:10
7
作者 余小灿 王春连 +6 位作者 刘成林 张招崇 徐海明 黄华 谢腾骁 李皓楠 刘锦磊 《Chinese Journal of Oceanology and Limnology》 SCIE CAS CSCD 2015年第6期1426-1435,共10页
We studied the sedimentary characteristics of a Paleocene-Eocene salt lake in the Jiangling Depression through field core observation,thin section identification,scanning electron microscopy,and X-ray diffraction anal... We studied the sedimentary characteristics of a Paleocene-Eocene salt lake in the Jiangling Depression through field core observation,thin section identification,scanning electron microscopy,and X-ray diffraction analysis.On the basis of sedimentary characteristics we have summarized the petrological and mineralogical characteristics of the salt lake and proposed 9 types of grade IV salt rhythms.The deposition shows a desalting to salting order of halite-argillaceous-mudstone-mud dolostonemud anhydrock-glauberite-halite.The relationship among grade IV rhythms,water salinity and climate fluctuations was analyzed.Based on the analysis of the relationship between boron content and mudstone color and by combining the mineralogy and sedimentary environment characteristics,we propose that the early and late Paleocene Shashi Formation in the Jiangling Depression was a paleolacustrine depositional environment with a high salt content,which is a representation of the shallow water salt lake depositional model.The middle Paleocene Shashi Formation and the early Eocene Xingouzui Formation were salt and brackish sedimentary environments with low salt content in a deep paleolake,which represents a deep salt lake depositional model. 展开更多
关键词 Paleocene-Eocene salt lake salt rhythm depositional model Jiangling Depression
下载PDF
Depositional Patterns and Oil/Gas Accumulation Features of Sha-3 Member Turbidites in Dongying Depression, Bohai Bay Basin 被引量:11
8
作者 BaiGuoping ZhangShanwen 《Petroleum Science》 SCIE CAS CSCD 2004年第2期105-110,共6页
Recent exploration results indicate that a significant exploration potential remains in the Dongying Depression of the Bohai Bay Basin and the undiscovered oil and gas are largely reservoired in subtle traps including... Recent exploration results indicate that a significant exploration potential remains in the Dongying Depression of the Bohai Bay Basin and the undiscovered oil and gas are largely reservoired in subtle traps including turbidite litholigcal traps of the Sha-3 Member. In order to effectively guide the exploration program targeting turbidites, this study will focus on the depositional models of the Sha-3 Member turbidites and oil/gas accumulation characteristics in these turbidites. Two corresponding relationships were found. One is that the East African Rift Valley provides a modern analog for the depositional systems in the Dongying Depression. The other is that the depositional models of line-sourced slope aprons, single point-source submarine fan and multiple source ramp turbidite, established for deep-sea turbidites, can be applied to interpret the depositional features of the turbidite fans of three different origins: slope turbidite aprons, lake floor turbidite fans and delta-fed turbidite fans in the Sha-3 Member. Updip sealing integrity is the key factor determining whether oil/gas accumulates or not in the slope aprons and lake floor fans. The factors controlling oil/gas migration and accumulation in the delta-fed turbidite fans are not very clear. Multiple factors rather than a single factor probably played significant roles in these processes. 展开更多
关键词 Dongying Depression Sha-3 Member TURBIDITE depositional model migration and accumulation features
下载PDF
Sedimentary system characteristics and depositional filling model of Upper Permian——Lower Triassic in South Yellow Sea Basin 被引量:6
9
作者 YUAN Yong CHEN Jian-wen +3 位作者 ZHANG Yin-g ZHANG Yu-xi LIANG Jie ZHANG Peng-hui 《Journal of Central South University》 SCIE EI CAS CSCD 2018年第12期2910-2928,共19页
In the South Yellow Sea Basin,Mesozoic–Paleozoic marine strata are generally well developed with large thickness,and no substantial breakthroughs have been made in hydrocarbon exploration.Through research,it is belie... In the South Yellow Sea Basin,Mesozoic–Paleozoic marine strata are generally well developed with large thickness,and no substantial breakthroughs have been made in hydrocarbon exploration.Through research,it is believed that the Upper Permian–Lower Triassic can be regarded as a long-term base-level cycle.Based on drilling data,characteristics of the lithology–electric property combination cyclicity,and the special lithology,the long-term base-level cycle was divided into five medium-term base-level cycles(MC1–MC5).On this basis,the Permian–Triassic sedimentary systems and their filling model were analyzed in accordance with the change of base-level cycle and transition of sedimentary environment,as well as characteristics of the drilling sedimentary facies and seismic facies.The results show that there were six sedimentary systems(fluvial,delta,tidal flat,open platform,restricted platform,and continental shelf)developed in the Upper Permian–Lower Triassic,the sedimentary systems were distributed such that the water was deep in the northwest and shallow in the southeast,and there were two base-level cycle filling models(a relatively stable tidal flat facies and a rapidly transgressive continental shelf facies to stable platform facies)developed in the Upper Permian–Lower Triassic.These models can provide a basis for evaluation of the Mesozoic–Paleozoic hydrocarbon geology in the South Yellow Sea Basin. 展开更多
关键词 sequence base-level cycle sedimentary system depositional filling model Upper Permian–Lower Triassic South Yellow Sea Basin
下载PDF
Tensile Properties of Mechanically-Defibrated Cellulose Nanofiber-Reinforced Polylactic Acid Matrix Composites Fabricated by Fused Deposition Modeling 被引量:5
10
作者 KURITA Hiroki BERNARD Chrystelle +1 位作者 LAVROVSKY Agathe NARITA Fumio 《Transactions of Nanjing University of Aeronautics and Astronautics》 EI CSCD 2021年第1期68-74,共7页
Biodegradable polymers are highly attractive as potential alternatives to petroleum-based polymers in an attempt to achieve carbon neutrality whilst maintaining the mechanical properties of the structures.Among these ... Biodegradable polymers are highly attractive as potential alternatives to petroleum-based polymers in an attempt to achieve carbon neutrality whilst maintaining the mechanical properties of the structures.Among these polymers,polylactic acid(PLA)is particularly promising due to its good mechanical properties,biocompatibility and thermoplasticity.In this work,we aim to enhance the mechanical properties of PLA using mechanically-defibrated cellulose nanofibers(CNFs)that exhibit remarkable mechanical properties and biodegradability.We also employ fused deposition modeling(FDM),one of the three-dimensional printing methods for thermoplastic polymers,for the low-cost fabrication of the products.Mechanically-defibrated CNF-reinforced PLA matrix composites are fabricated by FDM.Their tensile properties are investigated in two printing directions(0°/90°and+45°/-45°).The discussion about the relationship between printing direction and tensile behavoir of mechanically-defibrated CNF-reinforced PLA matrix composite is the unique point of this study.We further discuss the microstructure and fracture surface of mechanically-defibrated CNF-reinforced PLA matrix composite by scanning electron microscope. 展开更多
关键词 cellulose nanofiber(CNF) polylactic acid(PLA) tensile property fused deposition modeling
下载PDF
Depositional conditions and modeling of Triassic Oil shale in southern Ordos Basin using geochemical records 被引量:3
11
作者 LI De-lu LI Rong-xi +3 位作者 TAN Cheng-qian ZHAO Di) LIU Fu-tian ZHAO Bang-sheng 《Journal of Central South University》 SCIE EI CAS CSCD 2019年第12期3436-3456,共21页
Based on the element geochemistry and biomarkers of the oil shale from the Chang 7 sub-unit in the southern Ordos Basin,the depositional conditions and organic source of the oil shale are discussed.Biomarkers analyses... Based on the element geochemistry and biomarkers of the oil shale from the Chang 7 sub-unit in the southern Ordos Basin,the depositional conditions and organic source of the oil shale are discussed.Biomarkers analyses show that the oil shale has a homologous organic matter source,with a mix of plankton and advanced plants.U/Th and V/Ni ratios suggest that the redox condition is dominated by a reducing condition,and the degree of anoxia in the Tongchuan area is higher than that of the Xunyi area.Sr/Ba ratios illustrate that the oil shale is deposited in fresh water and the paleosalinity in the Tongchuan area is slightly higher.Fe/Ti ratios imply that the Tongchuan area underwent obvious hydrothermal fluid activities.Sr/Cu ratios show warm and humid paleoclimate in both areas.As assessed by(La/Yb)NASC,the deposition rate in the Tongchuan area is relatively lower.Fe/Co and Th/U ratios suggest that the paleo-water-depth in the Tongchuan area is deeper.The source rock could have the advance plants source,which must have close relationship with the Qinling orogeny.Comparing the paleoenvironment,the Tongchuan area has better depositional conditions,and is the key oil shale exploration area in the southern Ordos Basin. 展开更多
关键词 oil shale geochemistry depositional model Chang 7 Ordos Basin
下载PDF
A fiber Bragg grating based earth and water pressures transducer with three-dimensional fused deposition modeling for soil mass 被引量:4
12
作者 Yue Qin Qiankun Wang +2 位作者 Dongsheng Xu Jiaming Yan Shanshan Zhang 《Journal of Rock Mechanics and Geotechnical Engineering》 SCIE CSCD 2022年第2期663-669,共7页
A novel fiber Bragg grating(FBG)sensor with three-dimensional(3D)fused deposition modeling(FDM)approach is proposed for effective stress measurement in soil mass.The three-diaphragm structure design is developed to me... A novel fiber Bragg grating(FBG)sensor with three-dimensional(3D)fused deposition modeling(FDM)approach is proposed for effective stress measurement in soil mass.The three-diaphragm structure design is developed to measure earth and water pressures simultaneously.The proposed transducer has advantages of small size,high sensitivity,low cost,immunity to electromagnetic interference and rapid prototyping.The working principle,design parameters,and manufacturing details are discussed.The proposed transducer was calibrated for earth and water pressures measurement by using weights and a specially designed pressure chamber,respectively.The calibration results showed that the wavelength of the transducer was proportional to the applied pressure.The sensitivity coefficients of the earth and water pressures were 12.633 nm/MPa and 6.282 nm/MPa,respectively.Repeated tests and error analysis demonstrated the excellent stability and accuracy of the earth and water pressure measurements.The performance of the proposed transducer was further verified by a model experimental test and numerical analysis,which indicated that the proposed transducer has great potential for practical applications. 展开更多
关键词 Fused deposition modeling(FDM) Fiber bragg-grating(FBG)sensor Earth pressure Water pressure
下载PDF
Characterization for elastic constants of fused deposition modelling-fabricated materials based on the virtual fields method and digital image correlation 被引量:3
13
作者 Quankun Cao Huimin Xie 《Acta Mechanica Sinica》 SCIE EI CAS CSCD 2017年第6期1075-1083,共9页
Fused deposition modelling(FDM), a widely used rapid prototyping process, is a promising technique in manufacturing engineering. In this work, a method for characterizing elastic constants of FDM-fabricated materials ... Fused deposition modelling(FDM), a widely used rapid prototyping process, is a promising technique in manufacturing engineering. In this work, a method for characterizing elastic constants of FDM-fabricated materials is proposed. First of all, according to the manufacturing process of FDM, orthotropic constitutive model is used to describe the mechanical behavior. Then the virtual fields method(VFM) is applied to characterize all the mechanical parameters(Q, Q, Q, Q) using the full-field strain,which is measured by digital image correlation(DIC). Since the principal axis of the FDM-fabricated structure is sometimes unknown due to the complexity of the manufacturing process, a disk in diametrical compression is used as the load configuration so that the loading angle can be changed conveniently. To verify the feasibility of the proposed method, finite element method(FEM) simulation is conducted to obtain the strain field of the disk. The simulation results show that higher accuracy can be achieved when the loading angle is close to 30?. Finally, a disk fabricated by FDM was used for the experiment. By rotating the disk, several tests with different loading angles were conducted. To determine the position of the principal axis in each test, two groups of parameters(Q, Q, Q, Q) are calculated by two different groups of virtual fields. Then the corresponding loading angle can be determined by minimizing the deviation between two groups of the parameters. After that, the four constants(Q, Q, Q, Q) were determined from the test with an angle of 27?. 展开更多
关键词 Fused deposition modelling Virtual fields method Digital image correlation Orthotropic constitutive model Disk compression
下载PDF
Design and Manufacturing Strategies for Fused Deposition Modelling in Additive Manufacturing:A Review 被引量:3
14
作者 Hugo I.Medellin-Castillo Jorge Zaragoza-Siqueiros 《Chinese Journal of Mechanical Engineering》 SCIE EI CAS CSCD 2019年第3期1-16,共16页
Although several research works in the literature have focused on studying the capabilities of additive manufacturing(AM) systems, few works have addressed the development of Design for Additive Manufacturing(DfAM) kn... Although several research works in the literature have focused on studying the capabilities of additive manufacturing(AM) systems, few works have addressed the development of Design for Additive Manufacturing(DfAM) knowledge,tools, rules, and methodologies, which has limited the penetration and impact of AM in industry. In this paper a comprehensive review of design and manufacturing strategies for Fused Deposition Modelling(FDM) is presented.Consequently, several DfAM strategies are proposed and analysed based on existing research works and the operation principles, materials, capabilities and limitations of the FDM process. These strategies have been divided into four main groups: geometry, quality, materials and sustainability. The implementation and practicality of the proposed DfAM is illustrated by three case studies. The new proposed DfAM strategies are intended to assist designers and manufacturers when making decisions to satisfy functional needs, while ensuring manufacturability in FDM systems.Moreover, many of these strategies can be applied or extended to other AM processes besides FDM. 展开更多
关键词 Additive manufacturing(AM) Design for additive manufacturing(DfAM) Fused deposition Modelling(FDM) Design and manufacturing strategies
下载PDF
Comparison of wear behavior of ABS and Nylon6-Fe powder composite parts prepared with fused deposition modelling 被引量:2
15
作者 Harish Kumar Garg Rupinder Singh 《Journal of Central South University》 SCIE EI CAS CSCD 2015年第10期3705-3711,共7页
Fused deposition modeling(FDM) is one of the latest rapid prototyping techniques in which parts can be manufactured at a fast pace and are manufactured with a high accuracy. This research work is carried out to study ... Fused deposition modeling(FDM) is one of the latest rapid prototyping techniques in which parts can be manufactured at a fast pace and are manufactured with a high accuracy. This research work is carried out to study the friction and wear behavior of parts made of newly developed Nylon6-Fe composite material by FDM. This work also involves the comparison of the friction and wear characteristics of the Nylon6-Fe composite with the existing acrylonitrile butadiene styrene(ABS) filament of the FDM machine. This Is carried out on the pin on disk setup by varying the load(5, 10, 15 and 20 N) and speed(200 and 300 r/min). It is concluded that the newly developed composite is highly wear resistant and can be used in industrial applications where wear resistance is of paramount importance. Morphology of the surface in contact with the Nylon6-Fe composite and ABS is also carried out. 展开更多
关键词 composite material fused deposition modeling(FDM) parts TRIBOLOGY pin on disc iron(Fe) Nylon 6 acrylonitrile butadiene styrene(ABS)
下载PDF
Simulating Dry Deposition Fluxes of PM_(10) and Particulate Inorganic Nitrogen over the Eastern China Seas During a Severe Asian Dust Event Using WRF-Chem Model 被引量:5
16
作者 YAN Han GAO Huiwang +1 位作者 YAO Xiaohong WANG Zifa 《Journal of Ocean University of China》 SCIE CAS 2012年第3期301-314,共14页
A WRF-Chem model including a comprehensive gas-phase nitrogen chemistry module was used to simulate a severe dust event appearing in the eastern China on 19-25 March, 2002. The modeling result well reproduced PM10 con... A WRF-Chem model including a comprehensive gas-phase nitrogen chemistry module was used to simulate a severe dust event appearing in the eastern China on 19-25 March, 2002. The modeling result well reproduced PM10 concentrations in various distances from the dust sources and the transport pathway of the dust strom. The results showed that both the concentrations and the dry deposition fluxes of PM10 increased over the China seas during the dust event following the passage of a cold front system. The maximum fluxes of PM10 in the Yellow Sea and the East China Sea during the dust event were 5.5 and 8.4 times of those before the event, respectively. However, the temporal variations of the dry deposition fluxes of particulate inorganic nitrogen differed over the Yellow Sea from those over the East China Sea. Nitrate and ammonium in the whole northern China rapidly decreased because of the intrusion of dust-loaded air on 19 March. The dust plume arrived in the Yellow Sea on 20 March, decreasing the particulate inorganic nitrogen in mass concentration accordingly. The minimum dry deposition fluxes of nitrate and ammonium in the Yellow Sea were about 3/5 and 1/6 of those before the dust arrival, respectively. In contrast, when the dust plume crossed over the Yangtze Delta area, it became abundant in nitrate and ammonium and increased the concentrations and dry deposition fluxes of particulate inorganic nitrogen over the East China Sea, where the maximum dry deposition fluxes of nitrate and ammonium increased approximately by 4.1 and 2.6 times of those prior to the dust arrival. 展开更多
关键词 Asian dust aerosol inorganic particulate nitrogen dry deposition flux WRF-Chem model
下载PDF
PROTOTYPE SURFACE MICRO- PRECISION IN FUSED DEPOSITION MODELING PROCESS 被引量:2
17
作者 WANG Tianming XI Juntong JIN Ye 《Chinese Journal of Mechanical Engineering》 SCIE EI CAS CSCD 2007年第1期100-106,共7页
To aim at prototype parts fabricated with fused deposition modeling (FDM) process, the problems how to improve and enhance their surface micro-precision are studied. The producing mechanism of surface roughness is e... To aim at prototype parts fabricated with fused deposition modeling (FDM) process, the problems how to improve and enhance their surface micro-precision are studied. The producing mechanism of surface roughness is explained with three aspects concretely including the principle error of rapid prototyping (RP) process, the inherent characteristics of FDM process, and some mi- cro-scratches on the surface of the extruded fiber. Based on the micro-characters of section shape of the FDM prototype, a physical model reflecting the outer shape characters is abstracted. With the physical simplified and deduced, the evaluating equations of surface roughness are acquired. According to the FDM sample parts with special design for experimental measurement, the real surface roughness values of different inclined planes are obtained. And the measuring values of surface roughness are compared with the calculation values. Furthermore, the causes of surface roughness deviation between measuring values and calculation values are respectively analyzed and studied. With the references of analytic conclusions, the measuring values of the experimental part surface are revised, and the revised values nearly accord with the calculation values. Based on the influencing principles of FDM process parameters and special post processing of FDM prototype parts, some concrete measures are proposed to reduce the surface roughness of FDM parts, and the applying effects are better. 展开更多
关键词 Rapid prototyping Fused deposition modeling Micro-precision Surface roughness Post processing sequence
下载PDF
Grade-Tonnage, Ore Value-Tonnage, andEnrichment Ratio-Tonnage Models forResource Assessment
18
作者 Shoji Tetsuya Department of Environment Systems, The University of Tokyo, Tokyo 113-0033, Japan 《Journal of China University of Geosciences》 SCIE CSCD 2001年第1期45-53,共9页
According to grade-tonnage diagrams of nickel and zinc deposits, their critical grades are 0.4 % and 3. 4 %, respectively, and hence the former resources can be considered optimistic and the latter pessimistic. The gr... According to grade-tonnage diagrams of nickel and zinc deposits, their critical grades are 0.4 % and 3. 4 %, respectively, and hence the former resources can be considered optimistic and the latter pessimistic. The grade-tonnage diagram of gold deposits is convex downwards suggesting that the critical grade is 1 X 10-6 in the low-grade part. The ore value (OV)-tonnage diagram of all deposits In the world consists of three parts: high, middle and low vain f classes. The enrichment ratio (ER)-tonnage diagram of all deposits in the world ho consists of three parts: high, middle and low ratio classes.Nine quality categories defined by ER and OV are characterized by some keywords indicating deposit types as follows: category RH (high ER-high OV: 0. 7 %) by 'unconformity' and 'Mississippi Val-ley', category HM (high ER-middle: OV: 0.7 %) by 'vein', category ML (middle ER-low OV: 0 %) by 'sandstone', 'stockwork' and' dissemination', category LM by 'orthomagmatic',' laterite',komatiite and ' chemical', and category LL by 'porphyry', 'dissemination' and 'placer'. Category MM is not characterized by any keyword. If the commodities of a deposit are defined by both the enrichment ratio and the ore value, the defined commodities are relatively coincident for gold and nickel,but different for copper, silver and zinc, and greatly different for molybdenum and lead. Deposits containing lead and/or zinc are complimentary. If the commodity Ph+Zn is applied, most lead or zinc deposits are classified as Ph+Zu by both definitions. Accessory metals are commonly expected for deposits of kuroko-type zinc, epithermal silver, massive sulfide-type zinc and volcanogenic zinc, but uncommon for deposits of orthomagmatic chromium, chemically precipitated copper and sandstone-type uranium. 展开更多
关键词 GRADE ore value enrichment ratio TONNAGE mineral resources deposit model.
下载PDF
Microstructure and Deposition Mechanism of C/SiCN Composites Prepared by Rapid Electro-thermal Pyrolysis CVD
19
作者 夏熠 QIAO Shengru WANG Qiangqiang 《Journal of Wuhan University of Technology(Materials Science)》 SCIE EI CAS 2013年第4期688-692,共5页
Carbon fiber-reinforced silicon carbonitride ceramic matrix composites (C/SiCN) were prepared by rapid electro-thermal pyrolysis CVD using liquid polymer hexamethyldisilazane (HMDS, (CH3)3SiNHSi(CH3)3) as prec... Carbon fiber-reinforced silicon carbonitride ceramic matrix composites (C/SiCN) were prepared by rapid electro-thermal pyrolysis CVD using liquid polymer hexamethyldisilazane (HMDS, (CH3)3SiNHSi(CH3)3) as precursor. Microstructure morphology and production technique of C/SiCN composites were investigated. Scanning electron microscopy and transmission electron microscopy were respectively employed to characterize microstructures of the as-received C/SiCN composites samples. The high temperature pyrolysis of HMDS results in destruction of molecular chain, fracture of bonds, as well as liquid-gas-solid conversion from polymer to ceramic. Microstructures observation indicates that there is a high degree of coalescence between SiCN matrix and C fiber. The deposition model of liquid precursor electro-thermal pyrolysis CVD is different from that of gas precursor isothermal chemical vapor infiltration. Rapid liquid flow and slow gas diffusion are key factors for the difference of two methods. Preparation of rapid electro-thermal pyrolysis CVD consists of four steps including liquid polymer infiltration, polymer pyrolysis, rapid deposition of pyrolyzed substances and rapid densification, respectively. 展开更多
关键词 C/SiCN composite electro-thermal CVD MICROSTRUCTURE deposition model
下载PDF
Minimizing Warpage for Macro-Size Fused Deposition Modeling Parts
20
作者 Thanh Thuong Huynh Tien V.T.Nguyen +1 位作者 Quoc Manh Nguyen Trieu Khoa Nguyen 《Computers, Materials & Continua》 SCIE EI 2021年第9期2913-2923,共11页
In this study,we investigated warpage and corner lifting minimization for three-dimensional printed parts generated by macro-size fused deposition modeling(FDM).First,the reasons for warpage were theoretically elucida... In this study,we investigated warpage and corner lifting minimization for three-dimensional printed parts generated by macro-size fused deposition modeling(FDM).First,the reasons for warpage were theoretically elucidated.This approach revealed that the thermal deformation and differential volumetric shrinkage of the extruded molten plastic resulted in warpage of FDM parts.In addition,low adhesion between the deposited model and the heated or non-heated printing bed may intensify warpage further.As a next step,initial small-size and medium-size models were used to identify parameters to manage and minimize warpage in a way that would reduce material consumption and running time.Finally,a macro-size model was built to experimentally investigate and verify the technical solutions to minimize the warpage of FDM parts.In conclusion,an improved part with reduced warpage was efficiently produced after detailed consideration of thermal effects and adhesion force.Potential exists to widen the application scope of FDM technology in manufacturing for processes like thermoforming that involve mold core fabrication with heating.This technology,which has applications not only in mechanical engineering but also in related engineering fields,is convenient and could readily be applied to practical manufacturing industries. 展开更多
关键词 Fused deposition modeling corner lifting volumetric shrinkage thermal deformation acrylonitrile butadiene styrene filament
下载PDF
上一页 1 2 5 下一页 到第
使用帮助 返回顶部