Numerical modeling of destress blasting for strata separation

Destress blasting(DB)implemented along the perimeter of safety pillars is a special application of destressing in coal longwall mining.The goal is to separate relatively more deformed mined areas from safety pillars,such as shaft pillars or cross-cut pillars,to reduce the transfer of high stresses to the protective pillar.This case study aims to numerically simulate selected destress blasts in the Czech part of the Upper Silesian Coal Basin and examine its impact on stress transfer to the safety pillar area.To separate the area between the protective pillar and the longwall(LW),two fans of five 93-mm blast holes(length of 93e100 m)were drilled from the gate roads into the overburden strata.Each set of blast holes was fired separately in two stages without time delay.The explosive charge(gelatin-type of explosive)of each stage is 3450 kg.The two DB stages were fired when the longwall face was approximately 158 m and 152 m away from the blast.A 3D mine-wide model is built and validated with in situ stress measured with hydrofracturing.Mining and destressing in three 5-m thick coal seams are simulated in the region.Numerical modeling of DB is successfully conducted using a rock fragmentation factor a of 0.05 and a stress reduction/dissipation factor β of 0.95.Buffering of transfer of additional stress from the mining area into the safety pillar is evaluated by comparison of yielding volume before and after DB.It is shown that yielding volume drops after DB by nearly 80%in the area of the destressing panel and near the safety shaft pillar.

Protecting miners from coal bursts during development above historic mine workings in Harlan County,KY

In order to reach a large,untapped reserve of high-quality coal,D8 Cloverlick Mine proposed to mine a corridor nearly 600 m deep beneath the Benham Spur of Black Mountain,Kentucky’s highest peak.D8 Cloverlick Mine was extracting the Owl seam,but the corridor’s route lay approximately 20 m above century-old mine workings in the C–(Darby)seam.Adding to the concern,three serious coal bursts had recently occurred in nearby Owl seam workings.Maps of the old workings seemed to indicate that the underlying C–seam had been fully extracted.However,two of the coal bursts had occurred above areas where the C–Seam was also shown as mined out.Mine Safety and Health Administration(MSHA)Technical Support therefore investigated the records of past mining to better understand the old mine maps.Underground conditions observed in current Owl seam workings were also compared with the maps of the old C–seam workings.The study concluded that the presence of hazardous underlying remnants could not be ruled out.To mitigate the burst risk,D8 Cloverlick Mine adopted a strategy of stress probe drilling.A self-propelled coal drill was used to auger 11.5-m-long,small diameter holes in advance of mining.As each hole was drilled,the cuttings were measured to detect the presence of highly stressed coal.Ultimately the crossing was successfully completed without incident.

MINING INDUCED INFLUENCE ON THE ROADWAYS IN WEAK SURROUNDING ROCK AND ITS CONTROLLING MEASURES

The application of destressing method can change the distribution patterns of the stress field in the weak rock surrounding openings. locate the openings in the zone of low stress level, thus improve their loading and maintaining conditions. Such method is considered as a new way of opening maintenance in weak rock and has caused extensive interests in mining industry both at home and abroad. The results of theoretic research and lab experiments of utilizing top-destressing trough to maintain the opening affected by mining activities in weak rock, as well as its practical application in a coal mine are introduced in this paper. The research results indicate that the deformation and floor heaving of the opening in weak rock can be effectively controlled, and long-term stability of the opening can be realized by applying destressing method as long as the destressing plan and concerned parameters are carefully determined.

Large-scale destress blasting for seismicity control in hard rock mines:A case study

Destress blasting is a rockburst control technique where highly stressed rock is blasted to reduce the local stress and stiffness of the rock,thereby reducing its burst proneness.The technique is commonly practiced in deep hard rock mines in burst prone developments,as well as in sill or crown pillars which become burst-prone as the orebody is extracted.Large-scale destressing is a variant of destress blasting where panels are created parallel to the orebody strike with a longhole,fanning blast pattern from cross cut drifts situated in the host rock.The aim of panel destressing is to reduce the stress concentration in the ore blocks or pillars to be mined.This paper focuses on the large-scale destress blasting program conducted at Vale's Copper Cliff Mine(CCM)in Ontario,Canada.The merits of panel destressing are examined through field measurements of mining induced stress changes in the pillar.The destressing mechanism is simulated with a rock fragmentation factor(a)and stress reduction/dissipation factor(b).A 3D model is built and validated with measured induced stress changes.It is shown that the best correlation between the numerical model and field measurements is obtained when the combination of a and b indicates that the blast causes high fragmentation(a=0.05)and high stress release(b=0.95)in the destress panel.It is demonstrated that the burst proneness of the ore blocks in the panel stress shadow is reduced in terms of the brittle shear ratio(BSR)and the burst potential index(BPI).

Assessment and analysis of strata movement with special reference to rock burst mechanism in island longwall panel

This study presents a novel approach using theoretical analysis to assess the risk of rock burst of an island longwall panel that accounts for the coupled behavior of stress distribution and overlying strata movement. The height of destressed zone(HDZ) above the mined panel was first determined based on the strain energy balance in an underground coal mining area. HDZ plays a vital role in accurately determining the amount of different loads being transferred towards the front abutment and panel sides. Subsequently, based on the load transfer mechanisms, a series of formulae were derived for the average static and dynamic stresses in the island pillar through theoretical analysis. Finally, the model was applied to determining the side abutment stress distribution of LW 3112 in the Chaoyang Coal Mine and the results of ground subsidence monitoring were used to verify the predicted model. It can be concluded that the proposed computational model can be successfully applied to determining the safety of mining in island longwall panels.

Geomechanical effects of stress shadow created by large-scale destress blasting

This study aims to determine if large-scale choked panel destress blasting can provide sufficient beneficial stress reduction in highly-stressed remnant ore pillar that is planned for production. The orebody is divided into 20 stopes over 2 levels, and 2 panels are choke-blasted in the hanging wall to shield the ore pillar by creating a stress shadow around it. A linear-elastic model of the mining system is constructed with finite difference code FLAC3 D. The effect of destress blasting in the panels is simulated by applying a fragmentation factor(α) to the rock mass stiffness and a stress reduction factor(β) to the current state of stress in the region occupied by the destress panels. As an extreme case, the destress panel is also modeled as a void to obtain the maximum possible beneficial effects of destressing and stress shadow.Four stopes are mined in the stress shadow of the panels in 6 lifts and then backfilled. The effect of destress blasting on the remnant ore pillar is quantified based on stress change and brittle shear ratio(BSR) in the stress shadow zone compared to the base case without destress blasting. To establish realistic rock fragmentation and stress reduction factors, model results are compared to measured stress changes reported for case studies at Fraser and Brunswick mines. A 1.5 MPa immediate stress decrease was observed 20 m away from the panel at Fraser Mine, and a 4 MPa immediate stress decrease was observed 25 m away at Brunswick Mine. Comparable results are obtained from the current model with a rock fragmentation factor α of 0.2 and a stress reduction factor α of 0.8. It is shown that a destress blasting with these parameters reduces the major principal stress in the nearest stopes by 10-25 MPa.This yields an immediate reduction of BSR, which is deemed sufficient to reduce volume of ore at risk in the pillar.

Volumetric changes in the focal areas of seismic events corresponding to destress blasting

The typical development of total volumetric change in the focal areas of seismic events,corresponding to destress blasting,is characterized as an explosive phase followed by an implosive phase and with alternating additional phases following on from that.In a few cases,a non-typical development of volumetric change was identified,where the first phase was implosive and the second phase,explosive.This development is mainly typical for induced seismic events recorded during mining,not for destress blasting.Seismic events were recorded during longwall mining in the Czech part of the Upper Silesian Coal Basin,where the destress blasting technique is used as a rockburst prevention active measure.Kinematic source processes in the focal areas of selected seismic events were analyzed by the seismic moment tensor inversion method,as well as by studying geomechanical rock mass conditions at the localities of the seismic events.The main goal of the analysis was to attempt to identify the reasons for non-typical development of volumetric changes in these cases.Volumetric changes were analyzed for seismic events with energy greater than 104 J,recorded in the period of time from 1993 to 2009(1109 events).80%(891)of the recorded seismic events were induced seismic events that were registered during longwall mining and 20%(218)corresponded to destress blasting events.Research shows that the main reason for the non-typical development of volumetric changes in the focal areas of seismic events is an association with destress blasting in the rock mass,which is very close to rock mass overstressing.The detonation of explosives in boreholes,which would dominate the first phase of volumetric changes,probably obscured stress release in the rock mass,as manifested in the first implosion phase of the volumetric changes in this case.

A comparison of seismic response to conventional and face destress blasting during deep tunnel development

A novel design of development face destress blasting was implemented during the construction of an experimental tunnel at great depth.A second tunnel was developed nearby using conventional blasting as a control.The tunnels were developed parallel to one another and perpendicular to a high subhorizontal stress.High resolution seismic monitoring was used to record and compare the seismic response generated by each excavation.Analysis of the seismic data from the conventionally blasted tunnel indicated that the seismogenic zone of stress-driven instability extended up to 3.6 m ahead of the face.Destress blasting within the corresponding zone of the adjacent tunnel had the effect of reducing the rock mass stiffness,primarily due to weakening of the pre-existing natural discontinuities.The reduction in rock mass stiffness was inferred from the spatial broadening of the seismogenic zone and associated reduction in the measured spatial density of events,radiated energy and seismic potency ahead of the face.High strain gradients around the unsupported portion of the conventionally blasted excavation were implied by the rate at which the spatial density of seismicity changed with respect to the tunnel face position.In contrast,the change in the spatial density of seismicity around the destressed development face was much more gradual.This was indicative of lower strain gradients in the rock there.A reduction in rock mass stiffness following destress blasting was also indicated by the much wider variety of seismic source mechanisms recorded adjacent to the destressed tunnel.Seismic source mechanisms associated with destress blasting were also more clearly characteristic of compressive overstressing with fracture closure.The source mechanism data also indicated that destress blasting induced instability on all natural joint sets.When compared to conventional development blasting,destress blasting typically reduced violent strain energy release from the rock mass and the associated seismicity,but not always.

Development of a time-dependent energy model to calculate the mining-induced stress over gates and pillars

Generally, longwall mining-induced stress results from the stress relaxation due to destressed zone that occurs above the mined panel. Knowledge of induced stress is very important for accurate design of adjacent gateroads and intervening pillars which helps to raise the safety and productivity of longwall mining operations. This study presents a novel time-dependent analytical model for determination of the longwall mining-induced stress and investigates the coefficient of stress concentration over adjacent gates and pillars. The model is developed based on the strain energy balance in longwall mining incorporated to a rheological constitutive model of caved materials with time-varying parameters. The study site is the Tabas coal mine of Iran. In the proposed model, height of destressed zone above the mined panel, total longwall mining-induced stress, abutment angle, induced vertical stress, and coefficient of stress concentration over neighboring gates and intervening pillars are calculated. To evaluate the effect of proposed model parameters on the coefficient of stress concentration due to longwall mining, sensitivity analysis is performed based on the field data and experimental constants. Also, the results of the proposed model are compared with those of existing models. The comparative results confirm a good agreement between the proposed model and the in situ measurements. According to the obtained results, it is concluded that the proposed model can be successfully used to calculate the longwall mining-induced stress. Therefore, the optimum design of gate supports and pillar dimensions would be attainable which helps to increase the mining efficiency.

Numerical Simulation of the Relationship between the Width of Destressed Zone and Blasthole Depth

Overstress in the surrounding rock of the roadway is a key reason that causes failures of deep roadways. Destressing blasting is one of the promising techniques that could improve the supporting quality. If the depth of the pressure relief blast hole is too shallow, the surrounding rock of the roadway will be broken or even collapsed. If the pressure relief blast hole is too deep, the pressure relief area will be located in the deep part of the surrounding rock of the roadway, which cannot achieve the purpose of releasing the stress in the shallow part of the surrounding rock and cause waste of the blast hole. The width or range of the pressure relief area should just fall in the high stress area of the surrounding rock of the roadway, so the pressure relief blast hole should have a reasonable depth. In order to quantitatively describe the relationship between borehole depth and the width of the stress relief zone, numerical simulations were carried out in ANSYS according to different borehole depths. The results show that the optimal destressing effect is achieved when borehole depth is 4 m. Peak stress of and is significantly reduced by 30.51% and 49.07% after blasting. Meanwhile, the high-stress area shifts about 4.8 m from the roadside to the depth of surrounding rock, thus a 3.8 m wide stress relief zone is formed around the roadside, thus, the aim of quantizing the effects of destress blasting is achieved.

Seismic evaluation of the destress blasting efficiency

In this paper, selected methods of destress blasting efficiency assessment are presented, and novel quantitative methods based on in situ seismic measurements are proposed. The newly formulated solution combines two different approaches. The first, which is useful mostly for the near-field seismic analyses, is based on the analysis of seismic amplitude characteristics, and the second, relevant for farfield evaluation, is extended by the duration and frequency of the seismic wave. Both approaches are based on the seismic analyses of the waveforms generated by blasting recorded by the local seismic network. The proposed solutions are tested and validated in deep underground mines in Poland in which the room-and-pillar mining method is applied. Based on performed analysis, it is shown that both methods may be used as a rockburst hazard control in underground mines. However, developed methods may also be successfully implemented in other engineering practices, including the assessment of seismic vibrations in open pits and quarries.

Modeling and simulation of strata movement for protective seam mining with large interburden

Based on simulated material scale modeling and numerical simulation, the protective seam mining method was conducted at one coal mine. After extracting the No.15seam, the overlying strata movement and the deformation of the No.9-10 protected seamwere studied. The experiment results show that it is feasible to destress the protectedseams with large interburden thickness. When the face had advanced 200 m from thesetup room, the No.9-10 seam was fully destressed, resulting in easy gas drainage in thedestressed zone. Recommendations on mining sequence of multiple seams mining in thesame coal areas were made.

Numerical study on rock failure around a tunnel destressed by a conceptualized notched technique

A destressing method for reducing the strainburst risk in burst-prone grounds is suggested.In this method,the rock is destressed by cutting notches at the excavation boundary.First,the concept of the proposed method is described both analytically and numerically.Then,the method is applied to a tunneling problem.Several numerical models are built to study the destressing process and the failure mechanism around a circular tunnel.Results show that when the notch is added to the model,the rock at the tunnel wall is destressed,and the stress concentration zones shift to a farther distance away from the wall.Also,the analysis of the failure zone around the tunnel and the velocity of the failed elements show that the failure in the notched tunnel is less violent compared to that in the tunnel without the notch.Finally,a parametric study is conducted to investigate the influences of the notch dimensions on the stress distribution,deformation,and failures around the tunnel.