Current research on pump-turbine units is focused on the unstable operation at off-design conditions, with the characteristic curves in generating mode being S-shaped. Unlike in the traditional water turbines, pump-tu...Current research on pump-turbine units is focused on the unstable operation at off-design conditions, with the characteristic curves in generating mode being S-shaped. Unlike in the traditional water turbines, pump-turbine operation along the S-shaped curve can lead to difficulties during load rejection with unusual increases in the water pressure, which leads to machine vibrations. This paper describes both model tests and numerical simulations. A reduced scale model of a low specific speed pump-turbine was used for the performance tests, with comparisons to computational fluid dynamics（CFD） results. Predictions using the detached eddy simulation（DES） turbulence model, which is a combined Reynolds averaged Naviers-Stokes（RANS） and large eddy simulation（LES） model, are compared with the two-equation turbulence mode results. The external characteristics as well as the internal flow are for various guide vane openings to understand the unsteady flow along the so called S characteristics of a pump-turbine. Comparison of the experimental data with the CFD results for various conditions and times shows that DES model gives better agreement with experimental data than the two-equation turbulence model. For low flow conditions, the centrifugal forces and the large incident angle create large vortices between the guide vanes and the runner inlet in the runner passage, which is the main factor leading to the S-shaped characteristics. The turbulence model used here gives more accurate simulations of the internal flow characteristics of the pump-turbine and a more detailed force analysis which shows the mechanisms controlling of the S characteristics.展开更多
The Reynolds-averaged Navier-Stokes（RANS）,such as the original k-ω two-equation closures,have been very popular in providing good prediction for a wide variety of flows with presently available computational resour...The Reynolds-averaged Navier-Stokes（RANS）,such as the original k-ω two-equation closures,have been very popular in providing good prediction for a wide variety of flows with presently available computational resource.But for cavitating flows,the above equations noticeably over-predict turbulent production and hence effective viscosity.In this paper,the detached eddy simulation（DES） method for time-dependent turbulent cavitating flows is investigated.To assess the state-of-the-art of computational capabilities,different turbulence models including the widely used RANS model and DES model are conducted.Firstly,in order to investigate the grid dependency in computations,different grid sizes are adopted in the computation.Furthermore,the credibility of DES model is supported by the unsteady cavitating flows over a 2D hydrofoil.The results show that the DES model can effectively reduce the eddy viscosities.From the experimental validations regarding the force analysis,frequency and the unsteady cavity visualizations,more favorable agreement with experimental visualizations and measurements are obtained by DES model.DES model is better able to capture unsteady phenomena including cavity length and the resulting hydrodynamic characteristics,reproduces the time-averaged velocity quantitatively around the hydrofoil,and yields more acceptable and unsteady dynamics features.The DES model has shown to be effective in improving the overall predictive capability of unsteady cavitating flows.展开更多
In order to describe an investigation of the flow around high-speed train on a bridge under cross winds using detached-eddy simulation(DES), a 1/8th scale model of a three-car high-speed train and a typical bridge mod...In order to describe an investigation of the flow around high-speed train on a bridge under cross winds using detached-eddy simulation(DES), a 1/8th scale model of a three-car high-speed train and a typical bridge model are employed, Numerical wind tunnel technology based on computational fluid dynamics(CFD) is used, and the CFD models are set as stationary models. The Reynolds number of the flow, based on the inflow velocity and the height of the vehicle, is 1.9×10~6. The computations are conducted under three cases, train on the windward track on the bridge(WWC), train on the leeward track on the bridge(LWC) and train on the flat ground(FGC). Commercial software FLUENT is used and the mesh sensitivity research is carried out by three different grids: coarse, medium and fine. Results show that compared with FGC case, the side force coefficients of the head cars for the WWC and LWC cases increases by 14% and 29%, respectively; the coefficients of middle cars for the WWC and LWC increase by 32% and 10%, respectively; and that of the tail car increases by 45% for the WWC whereas decreases by 2% for the LWC case. The most notable thing is that the side force and the rolling moment of the head car are greater for the LWC, while the side force and the rolling moment of the middle car and the tail car are greater for the WWC. Comparing the velocity profiles at different locations, the flow is significantly influenced by the bridge-train system when the air is close to it. For the three cases(WWC, LWC and FGC), the pressure on the windward side of train is mostly positive while that of the leeward side is negative. The discrepancy of train's aerodynamic force is due to the different surface area of positive pressure and negative pressure zone. Many vortices are born on the leeward edge of the roofs. Theses vortices develop downstream, detach and dissipate into the wake region. The eddies develop irregularly, leading to a noticeably turbulent flow at leeward side of train.展开更多
Delayed detached eddy simulation(DDES)is performed to investigate an open cavity at Ma0.85.Clean cavity and cavity with leading-edge saw tooth spoiler and flattop spoiler,are modeled.The results obtained from clean ca...Delayed detached eddy simulation(DDES)is performed to investigate an open cavity at Ma0.85.Clean cavity and cavity with leading-edge saw tooth spoiler and flattop spoiler,are modeled.The results obtained from clean cavity prediction are compared with experimental sound pressure level(SPL)data from QinetiQ,UK.DDES results agree well with the experimental data.Furthermore,comparisons are made with the predicted SPL between the three configurations to find out the effect of different passive control methods.Both the spoilers can suppress the over-all SPL up to 8dB.The main focuses of this investigation are to exam the DDES method on cavity aeroacoustic analysis and test the noise suppression effect by saw tooth spoiler and flattop spoiler.展开更多
One of the objectives of car manufacturers is to improve engine performance, reduce consumption reduce emissions. To achieve this objective, it is important to understand the phenomena involved in the combustion chamb...One of the objectives of car manufacturers is to improve engine performance, reduce consumption reduce emissions. To achieve this objective, it is important to understand the phenomena involved in the combustion chambers of engines. These phenomena are numerous and complex in nature such: the aerodynamics, fuel-air mixture, turbulence, combustion and the cycle to cycle instabilities that cause more problems. One of the factors responsible for the phenomenon of cycle to cycle variations is the instability of the characteristics of the vortex flow Tumble. This instability may be due to changes in initial conditions. This study is achieved in order to contribute in a better understanding of engine flow by using a Detached Eddy Simulation Shear-Stress Transport (DES SST) model, which is a hybrid RANS/LES model. These simulations have been performed with the commercial CFD (computational fluid dynamic) code (FLUENT) coupled with our own development based on UDF facilities given by FLUENT. To explore the suitability of the 3D DES STT to simulate the internal flow, the calculation is performed for a model tumbling flow at constant volume. This flow has been measured in an experimental set up and measurements are used to initiate and to validate simulations. For this case study, we consider simplified engine geometry. To generate tumbling motion, we use non-reacting DES with a single cycle (SC) strategy. Also, with this strategy we study the effect of initial conditions on the instabilities that accompany a vortex type tumble.展开更多
Detailed formulation of the detached-eddy simulation （DES） based on shear stress transport model （SST） was deduced. Based on finite volume method, detached-eddy simulation of super- sonic turbulent flow over rearw...Detailed formulation of the detached-eddy simulation （DES） based on shear stress transport model （SST） was deduced. Based on finite volume method, detached-eddy simulation of super- sonic turbulent flow over rearward facing step was conducted. Multi-block structured non-conform grid was designed. The obtained distribution of wall pressure coefficient along the downstream of the step was in good agreement with experiment. The structure of supersonic flow over rearward facing step is complicated and contains boundary layer-shock interaction, shock-shock interaction and sec- ondary flow separation. The predictions of the corner pressure and location of the reattachment shock are more exact than the Reynolds-averaged method. Results show that detached-eddy simulation can simulate the supersonic separated flows exactly and has advantages over Reynolds-averaged method. The partition of the detached-eddy simulation can be easily achieved by using multi-block non-conform grid, which reduces the requirement of the computational resources as well.展开更多
RAN S(R eyno lds-averaged N av ier-Stokes)加湍流模型是当前计算飞机粘性流场的最常用方法,数值实践说明要计算大分离流动,需要更高级的方法例如LES(Large Eddy S im u lation)或DN S(D irect N S S im u lation)。然而实际雷诺数下,...RAN S(R eyno lds-averaged N av ier-Stokes)加湍流模型是当前计算飞机粘性流场的最常用方法,数值实践说明要计算大分离流动,需要更高级的方法例如LES(Large Eddy S im u lation)或DN S(D irect N S S im u lation)。然而实际雷诺数下,LES和DN S对网格的要求太高,以至目前还难以应用。DES(D etached-Eddy S im u lation)方法结合了RAN S和LES的优点,通过对Spalart-A llm aras湍流模型中长度尺度的修正,在近壁面它体现为RAN S模型的特点,而在远离物面处又保持LES的亚格子模型的特性。论文对比了采用RAN S和DES方法数值模拟翼型失速特性的能力,并与实验结果进行了对比。结果表明,对大分离流动的数值模拟,DES方法体现出更强的能力。展开更多
采用基于M enter k-ωSST两方程湍流模型的脱体涡模拟(D etached Eddy S im u lation,DES)方法,求解N av ier-Stokes方程,数值模拟了超音速下圆柱底部的大分离流动。脱体涡模拟在近物面区采用雷诺平均方法,在其它区域采用Sm agorinsk i...采用基于M enter k-ωSST两方程湍流模型的脱体涡模拟(D etached Eddy S im u lation,DES)方法,求解N av ier-Stokes方程,数值模拟了超音速下圆柱底部的大分离流动。脱体涡模拟在近物面区采用雷诺平均方法,在其它区域采用Sm agorinsk i大涡模拟方法,兼具前者计算量小的优点和后者能模拟大分离湍流流动的优势。与雷诺平均方法的计算结果进行对比发现,DES方法可以更好地模拟分离涡的发展,得到的底部径向压力分布的时间平均值与实验值吻合。展开更多
基金Supported by National Natural Science Foundation of China(Grant No.51139007)State Key Laboratory of Hydroscience and Engineering Open Foundation of China(Grant No.2014-KY-05)
文摘Current research on pump-turbine units is focused on the unstable operation at off-design conditions, with the characteristic curves in generating mode being S-shaped. Unlike in the traditional water turbines, pump-turbine operation along the S-shaped curve can lead to difficulties during load rejection with unusual increases in the water pressure, which leads to machine vibrations. This paper describes both model tests and numerical simulations. A reduced scale model of a low specific speed pump-turbine was used for the performance tests, with comparisons to computational fluid dynamics（CFD） results. Predictions using the detached eddy simulation（DES） turbulence model, which is a combined Reynolds averaged Naviers-Stokes（RANS） and large eddy simulation（LES） model, are compared with the two-equation turbulence mode results. The external characteristics as well as the internal flow are for various guide vane openings to understand the unsteady flow along the so called S characteristics of a pump-turbine. Comparison of the experimental data with the CFD results for various conditions and times shows that DES model gives better agreement with experimental data than the two-equation turbulence model. For low flow conditions, the centrifugal forces and the large incident angle create large vortices between the guide vanes and the runner inlet in the runner passage, which is the main factor leading to the S-shaped characteristics. The turbulence model used here gives more accurate simulations of the internal flow characteristics of the pump-turbine and a more detailed force analysis which shows the mechanisms controlling of the S characteristics.
基金supported by National Natural Science Foundation of China (Grant No.11172040)
文摘The Reynolds-averaged Navier-Stokes（RANS）,such as the original k-ω two-equation closures,have been very popular in providing good prediction for a wide variety of flows with presently available computational resource.But for cavitating flows,the above equations noticeably over-predict turbulent production and hence effective viscosity.In this paper,the detached eddy simulation（DES） method for time-dependent turbulent cavitating flows is investigated.To assess the state-of-the-art of computational capabilities,different turbulence models including the widely used RANS model and DES model are conducted.Firstly,in order to investigate the grid dependency in computations,different grid sizes are adopted in the computation.Furthermore,the credibility of DES model is supported by the unsteady cavitating flows over a 2D hydrofoil.The results show that the DES model can effectively reduce the eddy viscosities.From the experimental validations regarding the force analysis,frequency and the unsteady cavity visualizations,more favorable agreement with experimental visualizations and measurements are obtained by DES model.DES model is better able to capture unsteady phenomena including cavity length and the resulting hydrodynamic characteristics,reproduces the time-averaged velocity quantitatively around the hydrofoil,and yields more acceptable and unsteady dynamics features.The DES model has shown to be effective in improving the overall predictive capability of unsteady cavitating flows.
基金Project(U1534210)supported by the National Natural Science Foundation of ChinaProject(14JJ1003)supported by the Natural Science Foundation of Hunan Province,China+2 种基金Project(2015CX003)supported by the Project of Innovation-driven Plan in Central South University,ChinaProject(14JC1003)supported by the Natural Science Foundation of Hunan Province,ChinaProject(2015T002-A)supported by the Technological Research and Development program of China Railways Cooperation
文摘In order to describe an investigation of the flow around high-speed train on a bridge under cross winds using detached-eddy simulation(DES), a 1/8th scale model of a three-car high-speed train and a typical bridge model are employed, Numerical wind tunnel technology based on computational fluid dynamics(CFD) is used, and the CFD models are set as stationary models. The Reynolds number of the flow, based on the inflow velocity and the height of the vehicle, is 1.9×10~6. The computations are conducted under three cases, train on the windward track on the bridge(WWC), train on the leeward track on the bridge(LWC) and train on the flat ground(FGC). Commercial software FLUENT is used and the mesh sensitivity research is carried out by three different grids: coarse, medium and fine. Results show that compared with FGC case, the side force coefficients of the head cars for the WWC and LWC cases increases by 14% and 29%, respectively; the coefficients of middle cars for the WWC and LWC increase by 32% and 10%, respectively; and that of the tail car increases by 45% for the WWC whereas decreases by 2% for the LWC case. The most notable thing is that the side force and the rolling moment of the head car are greater for the LWC, while the side force and the rolling moment of the middle car and the tail car are greater for the WWC. Comparing the velocity profiles at different locations, the flow is significantly influenced by the bridge-train system when the air is close to it. For the three cases(WWC, LWC and FGC), the pressure on the windward side of train is mostly positive while that of the leeward side is negative. The discrepancy of train's aerodynamic force is due to the different surface area of positive pressure and negative pressure zone. Many vortices are born on the leeward edge of the roofs. Theses vortices develop downstream, detach and dissipate into the wake region. The eddies develop irregularly, leading to a noticeably turbulent flow at leeward side of train.
基金supported by the Priority Academic Program Development of Jiangsu Higher Education Institutions(PAPD)the Funding of Jiangsu Innovation Program for Graduate Education (KYLX_0296)the Fundamental Research Funds for the Central Universities
文摘Delayed detached eddy simulation(DDES)is performed to investigate an open cavity at Ma0.85.Clean cavity and cavity with leading-edge saw tooth spoiler and flattop spoiler,are modeled.The results obtained from clean cavity prediction are compared with experimental sound pressure level(SPL)data from QinetiQ,UK.DDES results agree well with the experimental data.Furthermore,comparisons are made with the predicted SPL between the three configurations to find out the effect of different passive control methods.Both the spoilers can suppress the over-all SPL up to 8dB.The main focuses of this investigation are to exam the DDES method on cavity aeroacoustic analysis and test the noise suppression effect by saw tooth spoiler and flattop spoiler.
文摘One of the objectives of car manufacturers is to improve engine performance, reduce consumption reduce emissions. To achieve this objective, it is important to understand the phenomena involved in the combustion chambers of engines. These phenomena are numerous and complex in nature such: the aerodynamics, fuel-air mixture, turbulence, combustion and the cycle to cycle instabilities that cause more problems. One of the factors responsible for the phenomenon of cycle to cycle variations is the instability of the characteristics of the vortex flow Tumble. This instability may be due to changes in initial conditions. This study is achieved in order to contribute in a better understanding of engine flow by using a Detached Eddy Simulation Shear-Stress Transport (DES SST) model, which is a hybrid RANS/LES model. These simulations have been performed with the commercial CFD (computational fluid dynamic) code (FLUENT) coupled with our own development based on UDF facilities given by FLUENT. To explore the suitability of the 3D DES STT to simulate the internal flow, the calculation is performed for a model tumbling flow at constant volume. This flow has been measured in an experimental set up and measurements are used to initiate and to validate simulations. For this case study, we consider simplified engine geometry. To generate tumbling motion, we use non-reacting DES with a single cycle (SC) strategy. Also, with this strategy we study the effect of initial conditions on the instabilities that accompany a vortex type tumble.
文摘Detailed formulation of the detached-eddy simulation （DES） based on shear stress transport model （SST） was deduced. Based on finite volume method, detached-eddy simulation of super- sonic turbulent flow over rearward facing step was conducted. Multi-block structured non-conform grid was designed. The obtained distribution of wall pressure coefficient along the downstream of the step was in good agreement with experiment. The structure of supersonic flow over rearward facing step is complicated and contains boundary layer-shock interaction, shock-shock interaction and sec- ondary flow separation. The predictions of the corner pressure and location of the reattachment shock are more exact than the Reynolds-averaged method. Results show that detached-eddy simulation can simulate the supersonic separated flows exactly and has advantages over Reynolds-averaged method. The partition of the detached-eddy simulation can be easily achieved by using multi-block non-conform grid, which reduces the requirement of the computational resources as well.
文摘RAN S(R eyno lds-averaged N av ier-Stokes)加湍流模型是当前计算飞机粘性流场的最常用方法,数值实践说明要计算大分离流动,需要更高级的方法例如LES(Large Eddy S im u lation)或DN S(D irect N S S im u lation)。然而实际雷诺数下,LES和DN S对网格的要求太高,以至目前还难以应用。DES(D etached-Eddy S im u lation)方法结合了RAN S和LES的优点,通过对Spalart-A llm aras湍流模型中长度尺度的修正,在近壁面它体现为RAN S模型的特点,而在远离物面处又保持LES的亚格子模型的特性。论文对比了采用RAN S和DES方法数值模拟翼型失速特性的能力,并与实验结果进行了对比。结果表明,对大分离流动的数值模拟,DES方法体现出更强的能力。
文摘采用基于M enter k-ωSST两方程湍流模型的脱体涡模拟(D etached Eddy S im u lation,DES)方法,求解N av ier-Stokes方程,数值模拟了超音速下圆柱底部的大分离流动。脱体涡模拟在近物面区采用雷诺平均方法,在其它区域采用Sm agorinsk i大涡模拟方法,兼具前者计算量小的优点和后者能模拟大分离湍流流动的优势。与雷诺平均方法的计算结果进行对比发现,DES方法可以更好地模拟分离涡的发展,得到的底部径向压力分布的时间平均值与实验值吻合。
