Detection accuracy of target accelerations based on vortex electromagnetic wave in keyhole space

The influence of the longitudinal acceleration and the angular acceleration of detecting target based on vortex electromagnetic waves in keyhole space are analyzed.The spectrum spreads of different orbital angular momentum(OAM)modes in different non-line-of-sight situations are simulated.The errors of target accelerations in detection are calculated and compared based on the OAM spectra spreading by using two combinations of composite OAM modes in the keyhole space.According to the research,the effects about spectrum spreads of higher OAM modes are more obvious.The error in detection is mainly affected by OAM spectrum spreading,which can be reduced by reasonably using different combinations of OAM modes in different practical situations.The above results provide a reference idea for investigating keyhole effect when vortex electromagnetic wave is used to detect accelerations.

Fault diagnosis method of link control system for gravitational wave detection

To maintain the stability of the inter-satellite link for gravitational wave detection,an intelligent learning monitoring and fast warning method of the inter-satellite link control system failure is proposed.Different from the traditional fault diagnosis optimization algorithms,the fault intelligent learning method pro-posed in this paper is able to quickly identify the faults of inter-satellite link control system despite the existence of strong cou-pling nonlinearity.By constructing a two-layer learning network,the method enables efficient joint diagnosis of fault areas and fault parameters.The simulation results show that the average identification time of the system fault area and fault parameters is 0.27 s,and the fault diagnosis efficiency is improved by 99.8%compared with the traditional algorithm.

Application of transient Rayleigh wave in detection of tunnel lining void area

Transient Rayleigh wave detection is a high-precision nondestructive detection method.At present,it has been widely used in shallow exploration,but rarely used in tunnel lining quality detection.Through the tunnel lining physical model experiment,the layout defects of the double-layer reinforcement lining area were detected and the Rayleigh wave velocity profile and dispersion curve were analyzed after data process-ing,which finally verified the feasibility and accuracy of Rayleigh wave method in detecting the tunnel lining void area.The results show that the method is not affected by the reinforcement inside the lining,the shallow detection is less disturbed and the accuracy is higher,and the data will fluctuate slightly with the deepening of the detection depth.At the same time,this method responds quite accurately to the thickness of the concrete,allowing for the assessment of the tunnel lining’s lack of compactness.This method has high efficiency,good reliability,and simple data processing,and is suitable for nondestructive detection of internal defects of tun-nel lining structure.

Application of Gaussian Beam Summation Migration in Reflected In-seam Wave Imaging

The geological conditions for coal mining in China are complex,with various structural issues such as faults and collapsed columns seriously compromising the safety of coal mine production.In-seam wave exploration is an effective technique for acquiring detailed information on geological structures in coal seam working faces.However,the existing reflected in-seam wave imaging technique can no longer meet the exploration precision requirements,making it imperative to develop a new reflected in-seam wave imaging technique.This study applies the Gaussian beam summation(GBS)migration method to imaging coal seams'reflected in-seam wave data.Firstly,with regard to the characteristics of the reflected in-seam wave data,methods such as wavefield removal and enveloped superposition are employed for the corresponding wavefield separation,wave train compression and other processing of reflected in-seam waves.Thereafter,imaging is performed using the GBS migration technique.The feasibility and effectiveness of the proposed method for reflected in-seam wave imaging are validated by conducting GBS migration tests on 3D coal-seam fault models with different dip angles and throws.By applying the method to reflected in-seam wave data for an actual coal seam working face,accurate imaging of a fault structure is obtained,thereby validating its practicality.

Parametric study on contact sensors for MASW measurement-based interfacial debonding detection for SCCS

Steel-concrete composite structures(SCCS)have been widely used as primary load-bearing components in large-scale civil infrastructures.As the basis of the co-working ability of steel plate and concrete,the bonding status plays an essential role in guaranteeing the structural performance of SCCS.Accordingly,efficient non-destructive testing(NDT)on interfacial debondings in SCCS has become a prominent research area.Multi-channel analysis of surface waves(MASW)has been validated as an effective NDT technique for interfacial debonding detection for SCCS.However,the feasibility of MASW must be validated using experimental measurements.This study establishes a high-frequency data synchronous acquisition system with 32 channels to perform comparative verification experiments in depth.First,the current sensing approaches for high-frequency vibration and stress waves are summarized.Secondly,three types of contact sensors,namely,piezoelectric lead-zirconate-titanate(PZT)patches,accelerometers,and ultrasonic transducers,are selected for MASW measurement.Then,the selection and optimization of the force hammer head are performed.Comparative experiments are carried out for the optimal selection of ultrasonic transducers,PZT patches,and accelerometers for MASW measurement.In addition,the influence of different pasting methods on the output signal of the sensor array is discussed.Experimental results indicate that optimized PZT patches,acceleration sensors,and ultrasonic transducers can provide efficient data acquisition for MASW-based non-destructive experiments.The research findings in this study lay a solid foundation for analyzing the recognition accuracy of contact MASW measurement using different sensor arrays.

Application of SPAC method and electromagnetic wave CT in karst detection of Wuhan Metro Line 8

In recent years,karst construction projects in the built-up area of Wuhan(capital of Hubei Province,China)are increasing,and the karst geological disasters have aroused social concerns.The actual engineering projects usually use shallow geophysical exploration methods to explore karst.This paper uses Spatial Auto-Correlation Method(SPAC)and electromagnetic Computerized Tomography(CT)to detect karst in urban built-up areas.Depending on the different physical properties of rock and soil,the SPAC method can better reveal the interface between soil and rock strata and the interface between soil layers.The electromagnetic CT method can identify strata according to the apparent absorption coefficient,which can better reveal the interface between soil and rock,the interface between the more intact and weathered rock.The SPAC method is mainly qualitative to measure the low-speed area,namely,the wrong geological body i.e.,karst cave,but also can detect the fracture zone or filling mode of karst cave,and at the same time,cannot use exploration holes or logging observation.The electromagnetic CT method can accurately detect the location and scale of the karst caves and has a higher accuracy detecting karst bands.In addition,exploration holes or well logging observations are also expected to be conducted,and their detection effect is greatly affected by lithology.

Detection technique of moving target based on passive millimeter wave

To solve the problem of insufficient ability when detecting the high-speed moving target with passive millimeter wave technology, a direct-detection passive millimeter wave detecting system using the monolithic microwave integrated cir- cuit （MMIC） millimeter wave radiometer is built, and the measured data are obtained by experiment under different condi- tions. Based on feature analysis of testing signals, it points out that the peak of the first pulse and interval of two peak pulses are valid features which can reflect the motion characteristic of target. A method to calculate the moving speed of target is put forward. The calculating results indicate that the proposed method has enough accuracy and is feasible to determine the parameters of the moving target using for passive millimeter wave system.

Acoustic wave detection of laser shock peening

In order to overcome the existing disadvantages of offline laser shock peening detection methods, an online detection method based on acoustic wave signals energy is provided. During the laser shock peening, an acoustic emission sen- sor at a defined position is used to collect the acoustic wave signals that propagate in the air. The acoustic wave signal is sampled, stored, digitally filtered and analyzed by the online laser shock peening detection system. Then the system gets the acoustic wave signal energy to measure the quality of the laser shock peening by establishing the correspondence between the acoustic wave signal energy and the laser pulse energy. The surface residual stresses of the samples are measured by X-ray stress analysis instrument to verify the reliability. The results show that both the surface residual stress and acoustic wave signal energy are increased with the laser pulse energy, and their growth trends are consistent. Finally, the empirical formula between the surface residual stress and the acoustic wave signal energy is established by the cubic equation fitting, which will provide a theoretical basis for the real-time online detection of laser shock peening.

FOULING DETECTION IN FOOD VESSELS USING INTERDIGITAL LAMB WAVE TRANSDUCER

Lamb waves are used to detect fouling in food vessels. The propagation of the Lamb waves in plates exhibits many modes and dispersion characteristics, which have great influence on fouling detection. The relative distribution of the in-plane and out-of-plane displacement of the mode across the thickness of the plate will determine the sensitivity of the mode to a particular loading condition. By considering the dispersion and multi-mode characteristics of guided waves, an interdigital polyvi- nylidene fluoride （PVDF） transducer is designed to realize the mode selection of gnided waves, and a single a0 mode is used for guided wave detection. Fouling detection experiments are conducted in the laboratory using epoxy adhesive on a thin plate. Using the interdigital PVDF transducer, three fouled areas are detected. Using one of the time-frequency analysis methods, the waveforms are further processed. This also demonstrates the validity of this method of fouling detection.

Defect detection in brazed weldment with lattice structure using ultrasonic Lamb wave technique

In this paper, defects detection in brazed weldment with lattice structure is studied using ultrasonic Lamb wave. Based on the ultrasonic guided wave theory, the frequency dispersion curves for phase and group velocity of I Cr18Ni9Ti are obtained by solving the Rayleigh-Lamb equation. The incident angles of different modes are determined through theoretical calculation and experimental analyses. Artificial defects of through-wall slots with different dimensions are made and tested. Experimental scattering effects of the fundamental symmetric mode S2 and asymmetric modes A1 and A0 are analysed and compared. The results show that mode Ao is suitable for detecting artificial defect, and the amplitude of the received signals are in good agreement with the defect size. Brazed weldment specimen containing lack of brazing with certain dimensions is made. Using the same methodology, scattering effects produced by weld defects are measured. The results show that the clutter wave brought about by the filler metal will certainly disturbs the identification of defect signal. But, when the defect is 3.0 mm in width, the presented mode Ao could be used potentially.

Robust Damage Detection and Localization Under Complex Environmental Conditions Using Singular Value Decomposition-based Feature Extraction and One-dimensional Convolutional Neural Network

Ultrasonic guided wave is an attractive monitoring technique for large-scale structures but is vulnerable to changes in environmental and operational conditions(EOC),which are inevitable in the normal inspection of civil and mechanical structures.This paper thus presents a robust guided wave-based method for damage detection and localization under complex environmental conditions by singular value decomposition-based feature extraction and one-dimensional convolutional neural network(1D-CNN).After singular value decomposition-based feature extraction processing,a temporal robust damage index(TRDI)is extracted,and the effect of EOCs is well removed.Hence,even for the signals with a very large temperature-varying range and low signal-to-noise ratios(SNRs),the final damage detection and localization accuracy retain perfect 100%.Verifications are conducted on two different experimental datasets.The first dataset consists of guided wave signals collected from a thin aluminum plate with artificial noises,and the second is a publicly available experimental dataset of guided wave signals acquired on a composite plate with a temperature ranging from 20℃to 60℃.It is demonstrated that the proposed method can detect and localize the damage accurately and rapidly,showing great potential for application in complex and unknown EOC.

Sensitivity function analysis of gravitational wave detection with single-laser and large-momentum-transfer atomic sensors

Recently, a configuration using atomic interferometers （AIs） had been sug- gested for the detection of gravitational waves. A new AI with some additional laser pulses for implementing large momentum transfer was also put forward, in order to reduce the effect of shot noise and laser frequency noise. We use a sensitivity function to analyze all possible configurations of the new AI and to distinguish how many mo- menta are transferred in a specific configuration. By analyzing the new configuration, we further explore a detection scheme for gravitational waves, in particular, that ame- liorates laser frequency noise. We find that the amelioration occurs in such a scheme, but novelly, in some cases, the frequency noise can be canceled completely by using a proper data processing method.

A Nonparametric Derivative-Based Method for R Wave Detection in ECG

QRS detection is very important in cardiovascular disease diagnosis and ECG (electrocardiogram) monitor, because it is the precondition of the calculation of correlative parameters and diagnosis. This paper presents a non-parametric derivative-based method for R wave detection in ECG signal. This method firstly uses a digital filter to cut out noises from ECG signals, utilizes local polynomial fitting that is a non-parametric derivative-based method to estimate the derivative values, and then selects appropriate thresholds by the difference, and the algorithm adaptively adjusts the size of thresholds periodically according to the different needs. Afterwards, the position of R wave is detected by the estimation of the first-order derivative values with nonparametric local polynomial statistical model. In addition, in order to improve the accuracy of detection, the method of redundant detection and missing detection are applied in this paper. The clinical experimental data are used to evaluate the effectiveness of the algorithm. Experimental results show that the method in the process of the detection of R wave is much smoother, compared with differential threshold algorithm and it can detect the R wave in the ECG signals accurately.

ANALYSIS OF GROUND TARGET STEALTH BASED ON PASSIVE MILLIMETER-WAVE DETECTION

Passive Millimeter-Wave(MMW)detection has become a threat to ground targets.Toenhance the survivability of the ground target in the future battlefield,passive MMW stealth tech-nology is analyzed in this paper.Based on the passive MMW detection principle,computation andanalysis are made for the MMW apparent temperature of tank in different actual combat conditions.The necessity of the passive MMW stealth is analyzed and the passive MMW stealth methods arealso studied.

Was LIGO’s Gravitational Wave Detection a False Alarm?

This article presents a new type of whitening filter (allowing the “passing” of some noise sources) applied to process the data recorded in LIGO’s GW150914 and GW151226 events. This new analysis shows that in the GW150914 event, the signals from the collision of two black holes are very similar to the 32.5 Hz noise sources observed in both of LIGO’s detectors. It also points out that these 32.5 Hz noise sources are powered by a 30 Hz sub harmonic, coming from the 60 Hz power system. In the GW1226 event, the same analysis points out that the NR template is very similar to the 120 Hz noise source. Therefore, the signals recorded in these events were probably generated by some small changes with the 60 Hz frequency in the US power grid. This can be caused, for example, by a power variation in the DC link, which can appear in both detectors in the same 10 ms time window. As this kind of power grid occurrence did not change the voltage levels, it may have gone unnoticed by LIGO’s electrical power supply’s monitoring system.

Optimal mother wavelet-based Lamb wave analyses and damage detection for composite structures

With the purpose of on-line structural health monitoring,a transducer network was embedded into compos- ite structure to minimize the influence of surroundings.The intrinsic dispersion characteristic of Lamb wave makes the wavelet transform an effective signal processing method for guided waves.To get high precision in feature extrac- tion,an information entropy-based optimal mother wavelet selection approach was proposed,which was used to choose the most appropriate basis function for particular Lamb wave analysis.By using the embedded sensor network and extracting time-of-flight,delamination in the composite laminate was identified and located.The results demon- strate the effectiveness of the proposed methods.

A System of Signal Detection and Estimation for Ground Wave Over-The-Horizon Radar

Ground wave over-the-horizon radar(GW-OTHR) can detect the OTH moving targets on sea or at low altitude. This paper discusses the background for detecting a target with GW-OTHR, introduces the theory and implementation of the signal detection and estimation system which has the parallel processing function, and gives some experimental results. The results of GW-OTHR experiments show that this system can successfully detect and estimate the above-mentioned targets.

Influence of roughness on the detection of mechanical characteristics of low-k film by the surface acoustic waves

The surface acoustic wave （SAW） technique is a precise and nondestructive method to detect the mechanical charac- teristics of the thin low dielectric constant （low-k） film by matching the theoretical dispersion curve with the experimental dispersion curve. In this paper, the influence of sample roughness on the precision of SAW mechanical detection is inves- tigated in detail. Random roughness values at the surface of low-k film and at the interface between this low-k film and the substrate are obtained by the Monte Carlo method. The dispersive characteristic of SAW on the layered structure with rough surface and rough interface is modeled by numerical simulation of finite element method. The Young＇s moduli of the Black DiamondTM samples with different roughness values are determined by SAWs in the experiment. The results show that the influence of sample roughness is very small when the root-mean-square （RMS） of roughness is smaller than 50 nm and correlation length is smaller than 20 μm. This study indicates that the SAW technique is reliable and precise in the nondestructive mechanical detection for low-k films.

QRS waves detection algorithm based on positive-negative adaptive threshold method

In order to accurately detect the occasional negative R waves in electrocardiography （ECG） signals, the positive-negative adaptive threshold method is adopted to determine the positive R waves and the negative R waves, according to difference characteristics of ECG signals. The Q and S waves can then be accurately positioned based on the basic characteristics of QRS waves. Finally, the algorithm simulation is made based on the signals from MIT-BIH database with MATLAB. The ex- perimental results show that the algorithm can improve the detection accuracy rate to 99. 91% and o- vercome the problem of larger computation load for wavelet transform and other methods, so the al- gorithm is suitable for real-time detection.

Estimation of detection threshold in multiple ship target situations with HF ground wave radar

A credible method of calculating the detection threshold is presented for the multiple target situations, which appear frequently in the lower Doppler velocity region during the surveillance of sea with HF ground wave radar. This method defines a whole-peak-outlier elimination （WPOE） criterion, which is based on in-peak-samples correlation of each target echo spectra, to trim off the target signals and abnormal disturbances with great amplitude from the complex spectra. Therefore, cleaned background noise samples are obtained to improve the accuracy and reliability of noise level estimation. When the background noise is nonhomogeneous, the detection samples are limited and often occupied heavily with outliers. In this case, the problem that the detection threshold is overvalued can be solved. In applications on experimental data, it is verified that this method can reduce the miss alarm rate of signal detection effectively in multiple target situations as well as make the adaptability of the detector better.