An innovative detection method of high frequency BPSK signal with low signal-to-noise ratio

Based on chaotic oscillator system, this paper proposes a novel method on high frequency low signal- to-noise ratio BPSK（ Binary Phase Shift Keying） signal detection. Chaotic oscillator system is a typical non-lin- ear system which is sensitive to periodic signals and immune to noise at the same time. Those properties make it possible to detect low signal-to-noise ratio signals. The BPSK signal is a common signal type which is widely used in modern communication. Starting from the analysis of advantages of chaotic, os~.illator system and signal features of the BPSK signal, we put forward a unique method that can detect low signar-to-noise ratio BPSK sig- nals with high frequency. The simulation results show that the novel method can dclct.t low signal-to-noise ratio BPSK signals with frequency in an order of magnitude of l0s Hz, and the input Signal-to-Noise Ratio threshold can be -20 dB.

Enhancement of signal-to-noise ratio of ultracold polar NaCs molecular spectra by phase locking detection

We report a method of high-sensitively detecting the weak signal in photoassociation （PA） spectra of ultracold NaCs molecules by phase sensitive-demodulated trap-loss spectra of Na atoms from a photomultiplier tube. We find that the signal-to-noise ratio （SNR） of the PA spectra is strongly dependent on the integration time and the sensitivity of the lock-in amplifier, and our results show reasonable agreement with the theoretical analyses of the SNR with the demodulation parameters. Meanwhile, we investigate the effect of the interaction time of the PA laser with the colliding Na-Cs atom pairs on the SNR of the PA spectra. The atom loss rate is dependent on both the PA-induced atom loss and the loading of the MOT. The high-sensitive detection of the excited ultracold NaCs molecules lays a solid foundation for further study of the formation and application of ultracold NaCs molecules.

Using Pearson’s System of Curves to Approximate the Distributions of the Difference between Two Correlated Estimates of Signal-to-Noise Ratios: The Cases of Bivariate Normal and Bivariate Lognormal Distributions

Background: The signal-to-noise ratio (SNR) is recognized as an index of measurements reproducibility. We derive the maximum likelihood estimators of SNR and discuss confidence interval construction on the difference between two correlated SNRs when the readings are from bivariate normal and bivariate lognormal distribution. We use the Pearsons system of curves to approximate the difference between the two estimates and use the bootstrap methods to validate the approximate distributions of the statistic of interest. Methods: The paper uses the delta method to find the first four central moments, and hence the skewness and kurtosis which are important in the determination of the parameters of the Pearsons distribution. Results: The approach is illustrated in two examples;one from veterinary microbiology and food safety data and the other on data from clinical medicine. We derived the four central moments of the target statistics, together with the bootstrap method to evaluate the parameters of Pearsons distribution. The fitted Pearsons curves of Types I and II were recommended based on the available data. The R-codes are also provided to be readily used by the readers.

Signal-to-noise ratio of Raman signal measured by multichannel detectors

Raman spectroscopy has been widely used to characterize the physical properties of two-dimensional materials(2DMs).The signal-to-noise ratio(SNR or S/N ratio)of Raman signal usually serves as an important indicator to evaluate the instrumental performance rather than Raman intensity itself.Multichannel detectors with outstanding sensitivity,rapid acquisition speed and low noise level have been widely equipped in Raman instruments for the measurement of Raman signal.In this mini-review,we first introduce the recent advances of Raman spectroscopy of 2DMs.Then we take the most commonly used CCD detector and IGA array detector as examples to overview the various noise sources in Raman measurements and analyze their potential influences on SNR of Raman signal in experiments.This overview can contribute to a better understanding on the SNR of Raman signal and the performance of multichannel detector for numerous researchers and instrumental design for industry,as well as offer practical strategies for improving spectral quality in routine measurement.

Methane concentration detection system based on differential infrared absorption

The infrared absorption method for methane concentration detection is an ideal way to detect methane at present. However, it is difficult to spread this method due to its high cost. In this paper, by using a wideband infrared light emitting di- ode （LED） accompanied with a PIN photo electric diode, a low-cost methane detection system was designed. To overcome the shortcomings caused by the wide working band, a differential light path was designed. By means of a differential ratio algo- rithm, the stability and the accuracy of the system were guaranteed. Finally, the validity of the system with the proposed algo- rithm was verified by the experiment results.

Voice activity detection based on deep belief networks using likelihood ratio

A novel technique is proposed to improve the performance of voice activity detection(VAD) by using deep belief networks(DBN) with a likelihood ratio(LR). The likelihood ratio is derived from the speech and noise spectral components that are assumed to follow the Gaussian probability density function(PDF). The proposed algorithm employs DBN learning in order to classify voice activity by using the input signal to calculate the likelihood ratio. Experiments show that the proposed algorithm yields improved results in various noise environments, compared to the conventional VAD algorithms. Furthermore, the DBN based algorithm decreases the detection probability of error with [0.7, 2.6] compared to the support vector machine based algorithm.

Effective DOA Estimation Under Low Signal-to-Noise Ratio Based on Multi-Source Information Meta Fusion

Efficiently performing high-resolution direction of arrival(DOA)estimation under low signal-to-noise ratio(SNR)conditions has always been a challenge task in the literatures.Obvi-ously,in order to address this problem,the key is how to mine or reveal as much DOA related in-formation as possible from the degraded array outputs.However,it is certain that there is no per-fect solution for low SNR DOA estimation designed in the way of winner-takes-all.Therefore,this paper proposes to explore in depth the complementary DOA related information that exists in spa-tial spectrums acquired by different basic DOA estimators.Specifically,these basic spatial spec-trums are employed as the input of multi-source information fusion model.And the multi-source in-formation fusion model is composed of three heterogeneous meta learning machines,namely neural networks(NN),support vector machine(SVM),and random forests(RF).The final meta-spec-trum can be obtained by performing a final decision-making method.Experimental results illus-trate that the proposed information fusion based DOA estimation method can really make full use of the complementary information in the spatial spectrums obtained by different basic DOA estim-ators.Even under low SNR conditions,promising DOA estimation performance can be achieved.

Signal-to-noise ratio of lensless ghost interference with thermal incoherent light

Factors influencing the signal-to-noise ratio （SNR） of lensless ghost interference with thermal incoherent light are investigated. Our result shows that the SNR of lensless ghost interference is related to the transverse length of the object, the position of the object in the imaging system and the transverse size of the light source. Furthermore, the effects of these factors on the SNR are discussed in detail by numerical simulations.

Noises and Signal-to-Noise Ratio of Nanosize EIS and ISFET Biosensors

The results of comparative theoretical analyzes of the behavior of internal low-frequency noises, signal-to-noise ratio and sensitivity to DNA molecules for EIS and ISFET based nanosize biosensors are presented. It is shown that EIS biosensor is more sensitive to the presence of DNA molecules in aqueous solution than ISFET sensor. Internal electrical noises level decreases with the increase of concentration of DNA molecules in aqueous solution. In the frequency range 10−3 - 103 Hz noises level for EIS sensor about in three orders is higher than for ISFET sensor. In the other hand, signal-to-noise ratio for capacitive EIS biosensor is much higher than for ISFET sensor.

GNSS spoofing detection for single antenna receivers via CNR variation monitoring

In this paper,a method for spoofing detection based on the variation of the signal’s carrier-to-noise ratio(CNR)is proposed.This method leverages the directionality of the antenna to induce varying gain changes in the signals across different incident directions,resulting in distinct CNR variations for each signal.A model is developed to calculate the variation value of the signal CNR based on the antenna gain pattern.This model enables the differentiation of the variation values of the CNR for authentic satellite signals and spoofing signals,thereby facilitating spoofing detection.The proposed method is capable of detecting spoofing signals with power and CNR similar to those of authentic satellite signals.The accuracy of the signal CNR variation value calculation model and the effectiveness of the spoofing detection method are verified through a series of experiments.In addition,the proposed spoofing detection method works not only for a single spoofing source but also for distributed spoofing sources.

Research on the sensitivity for the coal mine gas concentration detection by laser spectrum absorption

Because of the former gas chemistry examination method defects, tunable diode laser absorption spectrum technology （TDLAS） was used. It used an isolated absorption spectrum of the gas molecule to measure the gas absorption spectrum in order to distinguish the gas conveniently. The second harmonic （20 was measured in this system. Due to the fact which the harmonious signal is proportional to the concentration of the absorption gas, the gas concentration may be obtained through examining harmonious signal. The theoretical analysis and the experimental result indicate that under the same level of pressure, survey with the signal-to-noise ratio（SNR） of 2fsignal increases the accuracy by one order of magnitude and may reach 10 ^-3 and the sensitivity may reach the 10^-6 level compared to that of direct absorption. 5% methane density and a 30 cm absorption cell were used in the experiment. It has several advantages including high sensitivity, best resolution, and faster response and so on. The gas concentration monitoring of coal mine may be accomplished.

Influence of signal-to-noise ratio on accuracy of spectral analysis by near infrared spectroscopy

As one of the important indicators of spectrometer,signal-to-noise ratio(SNR)reflects the ability of spectrometer to detect weak signals.To investigate the influence of SNR on the prediction accuracy of spectral analysis,we first introduce the major factors affecting the spectral SNR.Taking green tea as an example,the influence of spectral SNR on the prediction accuracy of the origin identification model is analyzed by experiments.At the same time,the relationship between the spectral SNR and prediction accuracy of spectral analysis model is fitted.Based on this,the common methods for improving the spectral SNR are discussed.The results show that the accuracy of the prediction set model first decreases slowly,then decreases linearly,and finally tends to be flat as the spectral SNR decreases.Through calculation,in order to achieve the prediction accuracy of prediction model reaching 90%and 85%,the spectral SNR is required to be higher than 23.42 dB and 21.16 dB,respectively.The overall results provide certain parameters support for the development of new online analytical spectroscopic instruments,especially for the technical indicators of SNR.

Research and Simulation on Weak Signal Detection Based on Duffing Oscillator and Damping Ratio Perturbation

The chaotic system is sensitive to the initial value, and this can be applied in the weak signal detection. There are periodic, critical and chaotic states in a chaotic system. When the system is in the critical state, a small perturbation of system,n parameter may lead to a qualitative change of the system＇s state. This paper introduces a new method to detect weak signals by the way of disturbing the damping ratio. The authors choose the duffing equation, using MATLAB to carry on the simulation, to study the changes of the system when the signal to be measured is added to the damping ratio. By means of observing the phase loots chart and time damin chart, the weak signal will be detected.

Automatic Detection Instrument for the Ratio of Chlorine to Bromine in Oxidized Liquid of Bromine Production Based on Fuzzy Method

In the process of bromine production,because of lag adjustment methods,there are problems of adjusting delay,raw material wastage and low growth rate.By considering the nature of bromine production,with the help of fuzzy data processing method,computer detection and display technique,we designed an automatic detection instrument for the ratio of chlorine to bromine in oxidized liquid of bromine production.This instrument can be used to detect the different parameters of raw materials adjustment and control in real time,and afford assurance that raw materials will be adjusted in time.This paper briefly introduces the working mechanism,hardware and software design of the instrument.

Calculation method of the signal-to-noise ratio attribute of seismic data based on structural orientation

At present,most signal-to-noise ratio(SNR)estimation methods can only calculate the global and not the local SNR of seismic data.This paper proposes a calculation method of a structure-oriented-based seismic SNR attribute.The purpose is to characterize the temporal and spatial variation of the seismic data SNR.First,the local slope parameters of the seismic events are calculated using a plane wave decomposition filter.Then,the singular value decomposition method is used to calculate the local seismic data SNR,thereby obtaining it in time and space.The proposed method overcomes the insufficiency of a conventional global SNR to characterize any local seismic data features and uses the SNR as an attribute of seismic data to more accurately describe the signal-noise energy distribution characteristics of seismic data in time and space.The results of a theoretical model test and real data processing show that the SNR attribute can be used not only for seismic data quality evaluation but also for analysis and evaluation of denoising methods.

Signal-to-noise ratio comparison of angular signal radiography and phase stepping method

Grating-based x-ray phase contrast imaging has the potential to be applied in future medical applications as it is compatible with both laboratory and synchrotron source. However, information retrieval methods are important because acquisition speed, scanning mode, image quality, and radiation dose depend on them. Phase-stepping （PS） is a widely used method to retrieve information, while angular signal radiography （ASR） is a newly established method. In this manuscript, signal-to-noise ratios （SNRs） of ASR are compared with that of PS. Numerical experiments are performed to validate theoretical results. SNRs comparison shows that for refraction and scattering images ASR has higher SNR than PS method, while for absorption image both methods have same SNR. Therefore, our conclusions would have guideline in future preclinical and clinical applications.

Advanced derivative ratio filters for edge detection of potential field data

Edge location is an important information of the source,and can be obtained by the potential field data. Most edge detection methods of potential field data are the functions of horizontal and vertical derivatives.The authors provide a new strategy to establish edge detection filters that can improve the resolution to identify small bodies,which use the ratio functions of different-order derivatives to recognize the edges of the sources.The new filter is named as advanced derivative ratio( ADR) filter and balanced outputs can be produced for different forms of ADR filters. The ADR filters are tested on synthetic data and real potential field data. The advantage of the ADR filters is that they can detect the edges of the causative sources more precisely and clearly,and the model testing results show that the resolution of ADR filters is higher than other existing filters. The ADR filters were applied to real data,with more subtle details obtained.

Local Correlated Noise Improvement of Signal-to-Noise Ratio Gain in an Ensemble of Noisy Neuron

We theoretically investigate the collective response of an ensemble of leaky integrate-and-fire neuron units to a noisy periodic signal by including local spatially correlated noise. By using the linear response theory, we obtained the analytic expression of signal-to-noise ratio (SNR). Numerical simulation results show that the rms amplitude of internal noise can be increased up to?an optimal value where the output SNR reaches a maximum value. Due to the existence of the local spatially correlated noise in the units of the ensemble, the SNR gain of the collective ensemble response can exceed unity and can be optimized when the nearest-neighborhood correlation is negative. This nonlinear collective phenomenon of SNR gain amplification in an ensemble of leaky integrate-and-fire neuron units can be related to the array stochastic resonance (SR) phenomenon. Furthermore, we also show that the SNR gain can also be optimized by tuning the number of neuron units, frequency and?amplitude of the weak periodic signal. The present study illustrates the potential to utilize the local spatially correlation noise and the number of ensemble units for optimizing the collective response of the neuron to inputs, as well as a guidance in the design of information processing devices to weak signal detection.

Acquisition Practice of High Signal-to-Noise Ratio in YTB Block of Sichuan Basin

YTB block in Sichuan basin is a favorable area to exploit oil and gas in shallow tight rock. 3D seismic project of this zone has two characteristics. Firstly, it has high requirements for the tolerance rate of the construction process and the acquisition of high signal-to-noise ratio seismic data;Second, there are widely obstacles and noises that lead to difficult acquisition construction organization. In acquisition practice, high signal-to-noise ratio seismic data was obtained by reasonable design of construction scheme, optimization of excitation parameters, improvement of receiving conditions and optimization of obstacle crossing observation system. .