In order to improve the matrix performance of impregnated diamond drill bit to better meet the drilling needs,the effects of the addition of nano-WC and nano-NbC particles on the matrix material together with the mech...In order to improve the matrix performance of impregnated diamond drill bit to better meet the drilling needs,the effects of the addition of nano-WC and nano-NbC particles on the matrix material together with the mechanical properties and microstructure of the diamond-matrix composite material of the Fe-based diamond drill bit were studied by using the method of uniform formula design,regression analysis and solution finding.An indoor drilling test was also carried out using the fabricated impregnated diamond drill bit.The results showed that after the addition of nano-NbC and nano-WC,the hardness and flexural strength of the matrix material got improved,as the flexural strength of the diamond composite material increased to 4.29%,the wear-resistance ratio increased to 8.75%,and the tighter the chemical bonding between the diamond and the matrix.This,indicates that the addition of nanoparticles has a positive significance in improving the performance of the diamond composite.The results of the drilling test showed that the mechanical drilling speed of the impregnated diamond drill bit after nanoparticle strengthening is 25.85%higher than that of the conventional drill bit,and the matrix wear was increased by 17.5%.It proves that nanoparticles can improve the drilling performance and efficiency of drill bit.展开更多
This paper describes an investigation of active bit vibration on the penetration mechanisms and bit-rock interaction for drilling with a diamond impregnated coring bit. A series of drill-off tests(DOTs) were conducted...This paper describes an investigation of active bit vibration on the penetration mechanisms and bit-rock interaction for drilling with a diamond impregnated coring bit. A series of drill-off tests(DOTs) were conducted where the drilling rate-of-penetration(ROP) was measured at a series of step-wise increasing static bit thrusts or weight-on-bits(WOBs). Two active DOTs were conducted by applying 60 Hz axial vibration at the bit-rock interface using an electromagnetic vibrating table mounted underneath the drilling samples, and a passive DOT was conducted where the bit was allowed to vibrate naturally with lower amplitude due to the compliance of the drilling sample mountings. During drilling, an acoustic emission(AE) system was used to record the AE signals generated by the diamond cutter penetration and the cuttings were collected for grain size analysis. The instrumented drilling system recorded the dynamic motions of the bit-rock interface using a laser displacement sensor, a load cell, and an LVDT(linear variable differential transformer) recorded the dynamic WOB and the ROP, respectively. Calibration with the drilling system showed that rotary speed was approximately the same at any given WOB, facilitating comparison of the results at the same WOB. Analysis of the experimental results shows that the ROP of the bit at any given WOB increased with higher amplitude of axial bit-rock vibration, and the drill cuttings increased in size with a higher ROP. Spectral analysis of the AEs indicated that the higher ROP and larger cutting size were correlated with a higher AE energy and a lower AE frequency. This indicated that larger fractures were being created to generate larger cutting size. Overall, these results indicate that a greater magnitude of axial bit-rock vibration produces larger fractures and generates larger cuttings which, at the same rotary speed, results in a higher ROP.展开更多
基金National Center for International Research on Deep Earth Drilling and Resource Development,Faculty of Engineering,China University of Geosciences(Wuhan)(No.DEDRD-2022-08).
文摘In order to improve the matrix performance of impregnated diamond drill bit to better meet the drilling needs,the effects of the addition of nano-WC and nano-NbC particles on the matrix material together with the mechanical properties and microstructure of the diamond-matrix composite material of the Fe-based diamond drill bit were studied by using the method of uniform formula design,regression analysis and solution finding.An indoor drilling test was also carried out using the fabricated impregnated diamond drill bit.The results showed that after the addition of nano-NbC and nano-WC,the hardness and flexural strength of the matrix material got improved,as the flexural strength of the diamond composite material increased to 4.29%,the wear-resistance ratio increased to 8.75%,and the tighter the chemical bonding between the diamond and the matrix.This,indicates that the addition of nanoparticles has a positive significance in improving the performance of the diamond composite.The results of the drilling test showed that the mechanical drilling speed of the impregnated diamond drill bit after nanoparticle strengthening is 25.85%higher than that of the conventional drill bit,and the matrix wear was increased by 17.5%.It proves that nanoparticles can improve the drilling performance and efficiency of drill bit.
基金funded by Atlantic Canada Opportunity Agency (AIF contract number: 7812636-1920044)
文摘This paper describes an investigation of active bit vibration on the penetration mechanisms and bit-rock interaction for drilling with a diamond impregnated coring bit. A series of drill-off tests(DOTs) were conducted where the drilling rate-of-penetration(ROP) was measured at a series of step-wise increasing static bit thrusts or weight-on-bits(WOBs). Two active DOTs were conducted by applying 60 Hz axial vibration at the bit-rock interface using an electromagnetic vibrating table mounted underneath the drilling samples, and a passive DOT was conducted where the bit was allowed to vibrate naturally with lower amplitude due to the compliance of the drilling sample mountings. During drilling, an acoustic emission(AE) system was used to record the AE signals generated by the diamond cutter penetration and the cuttings were collected for grain size analysis. The instrumented drilling system recorded the dynamic motions of the bit-rock interface using a laser displacement sensor, a load cell, and an LVDT(linear variable differential transformer) recorded the dynamic WOB and the ROP, respectively. Calibration with the drilling system showed that rotary speed was approximately the same at any given WOB, facilitating comparison of the results at the same WOB. Analysis of the experimental results shows that the ROP of the bit at any given WOB increased with higher amplitude of axial bit-rock vibration, and the drill cuttings increased in size with a higher ROP. Spectral analysis of the AEs indicated that the higher ROP and larger cutting size were correlated with a higher AE energy and a lower AE frequency. This indicated that larger fractures were being created to generate larger cutting size. Overall, these results indicate that a greater magnitude of axial bit-rock vibration produces larger fractures and generates larger cuttings which, at the same rotary speed, results in a higher ROP.
