Application of pre-alloyed powders for diamond tools by ultrahigh pressure water atomization

Copper, iron and cobalt based pre-alloyed powders for diamond tools were prepared by ultrahigh pressure water atomization（UPWA） process. Pre-alloyed powders prepared by different processes including UPWA, conventional water atomization （CWA） and elemental metal mechanical mixing （EMMM） were sintered to segments and then compared in mechanical properties, holding force between matrix and diamond, fracture morphology of blank and sintering diamond section containing matrix. The results showed that the pre-alloyed powder prepared by UPWA exhibits the best mechanical properties including the relative density, the hardness and the bending strength of matrix sinteredsegment. Sintered segments fractography of UPWA pre-alloyed powder indicatesmechanical mosaic strength and chemical bonding force between the pre-alloyed powder and the diamond, leading to the great increase in the holding force between matrix and diamond. The mechanical performance andthe service life of diamond tools were greatly improved by UPWA pre-alloyed powders.

A study on comprehensive recycling of waste diamond tools

This article puts forward a new method of recycling materials in diamond tools comprehensively and efficiently by means of analyzing and summarizing various methods of recycling waste diamond tools.After the waste diamond tools were decomposed in a mixed acid,metals contained in it went into solution in their ionic forms,while diamond and tungsten carbide particles formed into residues to be reclaimed.The amounts of metal ions in the leaching solution were adjusted according to the contents of metals in the diamond tools;then,the leaching solution was co-precipitated using oxalic acid as precipitation agent,and ammonia water was added to adjust the pH value of the oxalic acid.Under the right conditions,the comprehensive precipitation rate of metals reached above 98%.Finally,ultrafine pre-alloy powder was obtained by hydrogen reduction of oxalate.

Research progress of nickel based filler for development of diamond tools

Owing to diamond excellent physical and chemical properties,so synthetic diamond abrasives are extensively used in manufacturing diamond tools are utilized in machining hard and brittle materials.The brazing technology is exploited with strong bonding force between the diamond and substrate,which can realize metallurgical and chemical bonding between the filler metals and diamond abrasives.In this paper,the research reports on nickel-based fillers for brazing diamond grains at home and abroad in recent years are reviewed systematically,with emphasis on the influence of alloying elements and active elements on the properties of nickel-based fillers.The advantages and disadvantages of Cr,B,Si,P,Mn,Fe,Cu,W,C in nickel-based fillers and the negative effects of impurity elements were summarized.The shortcomings in the research and application of nickel-based fillers were pointed out,which provided theoretical guidance for further systematic research and development of related technologies.

CURING PROCESS OF PHOTOPOLYMER RESIN BOND DIAMOND TOOLS

Analytical simulation and corresponding proof-test are adopted to study the principle of the curing process of photopolymer resin diamond tools. The influence of the diamond as abrasives in photopolymer resin owing to the absorptivity of the diamond for the UV light on the photopolymer resin curing process is discussed. Based on the above, a kind of diamond tool—dicing blade is selected to analyze the curing process of photopolymer bond diamond tools. An analytical model of curing process is developed and a correlation curve between the depth of polymerization of the photopolymer resin diamond tools and the exposure time to represent the curing process of photopolymer bond dicing blade. A test is done to proof-test the validity of the analytical model and the correlation curve. The simulated data fit the experimental results, which demonstrates the analytical models and numerical algorithm are of high reliability. The analytical simulation method could possibly be used to optimize the curing cycle and improve the quality of the photopolymers resin bond diamond tools.

Electroplating of diamond tools under economic and environmental care aspects

0 Introduction Economy and the protection of the environment are important topics.We are competent to talk about these topics.Due to the expanding areas of application for highprecision and electroplated diamond tools with reproducible quality and long life,of course the aspects of economy and environmental protection gain increasing significance.In this lecture we will explain and show that economical aspects and environmental aspects in diamond electro-plating do not contradict,but rather complement each other.

A critical review on the chemical wear and wear suppression of diamond tools in diamond cutting of ferrous metals

Diamond tools play a critical role in ultra-precision machining due to their excellent physical and mechanical material properties,such as that cutting edge can be sharpened to nanoscale accuracy.However,abrasive chemical reactions between diamond and non-diamond-machinable metal elements,including Fe,Cr,Ti,Ni,etc,can cause excessive tool wear in diamond cutting of such metals and most of their alloys.This paper reviews the latest achievements in the chemical wear and wear suppression methods for diamond tools in cutting of ferrous metals.The focus will be on the wear mechanism of diamond tools,and the typical wear reduction methods for diamond cutting of ferrous metals,including ultrasonic vibration cutting,cryogenic cutting,surface nitridation and plasma assisted cutting,etc.Relevant commercially available devices are introduced as well.Furthermore,future research trends in diamond tool wear suppression are discussed and examined.

Study of the morphology and properties of diamond joints brazed with carbide-reinforced Cu-Sn-Ti filler metal

Cu-Sn-Ti brazing filler is a new type of copper-based brazing filler for brazing diamond tools currently used in industry,but it suffers from poor wear resistance,high brazing temperature and low bond strength.This paper provides a way to improve the strength of dia-mond-brazed joints by adding zirconium carbide and tungsten carbide reinforcing phase particles to the Cu-Sn-Ti alloy,respectively.Dia-mond particles were attached to Q460 steel using Cu-Sn-Ti composite filler with the addition of the reinforcing phase,and experimental in-struments such as scanning electron microscope,X-ray diffractometer and energy spectrometer were used to investigate the brazed joint per-formance of the composite brazing material for brazing diamond.The results show that the addition of enhanced phase particles resulted in a metallurgical reaction at the joint of the composite brazed diamond,achieving a higher strength joint with no obvious cracks at the interface,while the addition of 15 wt.%WC resulted in excellent wear resistance and the highest hardness at the joint interface.

SURFACE ROUGHNESS PREDICTION MODEL FOR ULTRAPRECISION TURNING ALUMINIUM ALLOY WITH A SINGLE CRYSTAL DIAMOND TOOL

A surface roughness model utilizing regression analysis method is developedfor predicting roughness of ultra-precision machined surface with a single crystal diamond tool. Theeffects of the main variables, such as cutting speed, feed, and depth of cut on surface roughnessare also analyzed in diamond turning aluminum alloy. In order to predict the optimum cuttingconditions during process planning. A lot of experimental results show that the model can predictthe surface roughness effectively under a certain cutting conditions.

Effects of rare earth element lanthanum on the microstructure of copper matrix diamond tool materials

Effects of rare earth element La on the microstructure of Cumatrix diamond tools were researched under the conditions of variousmaterials components and the process parameters in order to improvematerials properties. SEM, XPS and X-ray were used to investigate thefracture section, microstructure and the element valence inmaterials. The Results shown that the combination of rare earthelement La and transition element Ti is advantageous to the bondingstate Between diamond particles and matrix, so it can improve thematerials properties. Suitable sintering temperature is 790 deg. C.

Experimental Investigation and Numerical Simulation on Interfacial Carbon Diffusion of Diamond Tool and Ferrous Metals

We numerically simulated and experimentally studied the interfacialcarbon diffusion between diamond tooland workpiece materials.A diffusion modelwith respect to carbon atoms of diamond toolpenetrating into chips and machined surface was established.The numericalsimulation results of the diffusion process revealthat the distribution laws of carbon atoms concentration have a close relationship with the diffusion distance,the diffusion time,and the originalcarbon concentration of the work material.In addition,diamond face cutting tests of die steels with different carbon content are conducted at different depth of cuts and feed rates to verify the previous simulation results.The micro-morphology of the chips is detected by scanning electron microscopy.Energy dispersive X-ray analysis was proposed to investigate the change in carbon content of the chips surface.The experimentalresults of this work are of benefit to a better understanding on the diffusion wear mechanism in single crystaldiamond cutting of ferrous metals.Moreover,the experimentalresults show that the diffusion wear of diamond could be reduced markedly by applying ultrasonic vibration to the cutting toolcompared with conventionalturning.

Approach for Polishing Diamond Coated Complicated Cutting Tool: Abrasive Flow Machining(AFM)

Lower surface roughness and sharper cutting edge are beneficial for improving the machining quality of the cut?ting tool, while coatings often deteriorate them. Focusing on the diamond coated WC?Co milling cutter, the abrasive flow machining(AFM) is selected for reducing the surface roughness and sharpening the cutting edge. Comparative cutting tests are conducted on di erent types of coated cutters before and after AFM, as well as uncoated WC?Co one, demonstrating that the boron?doped microcrystalline and undoped fine?grained composite diamond coated cutter after the AFM(AFM?BDM?UFGCD) is a good choice for the finish milling of the 6063 Al alloy in the present case, because it shows favorable machining quality close to the uncoated one, but much prolonged tool lifetime. Besides, compared with the micro?sized diamond films, it is much more convenient and e cient to finish the BDM?UFGCD coated cutter covered by nano?sized diamond grains, and resharpen its cutting edge by the AFM, owing to the lower initial surface roughness and hardness. Moreover, the boron incorporation and micro?sized grains in the underly?ing layer can enhance the film?substrate adhesion, avoid the rapid film removal in the machining process, and thus maximize the tool life(1040 m, four times more than the uncoated one). In general, the AFM is firstly proposed and discussed for post?processing the diamond coated complicated cutting tools, which is proved to be feasible for improving the cutting performance

An Indentation Method for Nanoprecision Measurement of Diamond Tool Edge Radius

In ductile mode cutting of brittle materials using di amond tools, such as ductile cutting of silicon and quartz for wafer fabrication , one of the key conditions for achieving ductile chip formation is to get the r ight ratio of tool cutting edge radius to the undeformed chip thickness. It has been shown that the undeformed chip thickness has to be in the order of nanomete rs and that the tool cutting edge radius has to be smaller than the undeformed c hip thickness. Therefore, nanoprecision measurement of diamond cutting tools has become a key issue for ductile mode cutting of brittle materials. In this paper , a non-destructive nanoprecision measurement method for diamond tool cutting e dge radius is presented. The basis of the method is that the exact profile of th e tool cutting edge can be perfectly copied by indenting the tool cutting edge o n the surface of a rigid-perfect plastic material, and that the copy of the pro file can be measured at nanoprecision level. Ideally, the first aspect of th e method is to make a perfect copy of the tool cutting edge profile by indentati on on the surface of a rigid-perfect plastic material which has no elastic spri ng back, so that a true copy of the tool cutting edge is maintained for subseque nt measurement. Since no rigid-perfect plastic material can be found in realit y, actual materials of rigid-elastic-plastic nature have to be used for the in dentation in the measurement method, and the material elastic error compensation coefficients have to be determined to cancel out the effect of elastic spring b ack. For the minimization of error compensation, criteria for the selection of t he optimal materials for the indentation measurement are found to be: 1) high ri gidity and high density, 2) large Young’s elastic modulus, and 3) low yield strength. One of such materials identified is copper. The second aspect of the method is to measure the radius of the indented profile on the surface of the ma terial. This can be achieved by using an atomic force microscope (AFM), and in t his paper the results for measurement of diamond tool edge radii of nanometer sc ales by indentation on a copper material are presented. The elastic error compen sation coefficient for the copper material is determined through the indentation of a tungsten carbide tool edge on the copper surface. By comparing the actual tool edge radius measured using SEM on the sectional view of the tungsten carbid e tool with the one measured from the copied profile of the tool edge on the cop per surface, the coefficient is obtained. Analysis is given for the accuracy of the proposed method, showing that as far as the elastic compensation coefficient is consistent with the material used for the indentation measurement, the only source of errors with the measurement will come from the device for measuring th e indented profile on the surface of the solid, in this case it will come from t he AFM which measures on the sub-nanometer scales.

Prediction of cutting force in ultra-precision machining of nonferrous metals based on strain energy

The effects of the nonuniform cutting force and elastic recovery of processed materials in ultra-precision machining are too complex to be treated using traditional cutting theories,and it is necessary to take account of factors such as size effects,the undeformed cutting thickness,the tool blunt radius,and the tool rake angle.Therefore,this paper proposes a new theoretical calculation model for accurately predicting the cutting force in ultra-precision machining,taking account of such factors.The model is first used to analyze the material deformation of the workpiece and the cutting force distribution along the cutting edge of a diamond tool.The size of the strain zone in different cutting deformation zones is then determined by using the distribution of strain work per unit volume and considering the characteristics of the stress distribution in these different deformation zones.Finally,the cutting force during ultra-precision machining is predicted precisely by calculating the material strain energy in different zones.A finite element analysis and experimental data on ultra-precision cutting of copper and aluminum are used to verify the predictions of the theoretical model.The results show that the error in the cutting force between the calculation results and predictions of the model is less than 14%.The effects of the rake face stress distribution of the diamond tool,the close contact zone,and material elastic recovery can be fully taken into account by the theoretical model.Thus,the proposed theoretical calculation method can effectively predict the cutting force in ultra-precision machining.

Elliptical vibration cutting of large-size thin-walled curved surface parts of pure iron by using diamond tool with active cutting edge shift

Large-size thin-walled curved surface parts of pure iron are crucial in aerospace,national defense,energy and precision physical experiments.However,the high machining accuracy and surface quality are difficult to achieve due to the serious tool wear and deformation when machining the parts with conventional cutting tools.In this paper,an elliptical vibration cutting(EVC)with active cutting edge shift(ACES)based on a long arbor vibration device is proposed for ultraprecision machining the pure iron parts by using diamond tool.Compared with cutting at a fixed cutting edge,the influence of ACES on the EVC was analyzed.Experiments in EVC of pure iron with ACES were conducted.The evolutions of the surface roughness,surface topography,and chip morphology with tool wear in EVC with ACES are revealed.The reasonable parameters of ultraprecision machining the pure iron parts by EVC with ACES were determined.It shows that the ACES has a slight influence on the machined surface roughness and surface topography.The diamond tool life can be significantly prolonged in EVC of pure iron with ACES than that with a fixed cutting edge,so that high profile accuracy and surface quality could be obtained even at higher nominal cutting speed.A typical thin-walled curved surface pure iron part with diameter φ240 mm,height 122 mm,and wall thickness 2 mm was fabricated by the presented method,and its profile error and surface roughness achieved PV 2.2μm and Ra less than 50 nm,respectively.

Cutting force and its frequency spectrum characteristics in high speed milling of titanium alloy with a polycrystalline diamond tool

In this paper, a series of experiments were performed by high speed milling of Ti-6.5Al-2Zr-1Mo-1V (TA15) by use of polycrystalline diamond (PCD) tools. The characteristics of high speed machining (HSM) dynamic milling forces were investi- gated. The effects of the parameters of the process, i.e., cutting speed, feed per tooth, and depth of axial cut, on cutting forces were studied. The cutting force signals under different cutting speed conditions and different cutting tool wear stages were analyzed by frequency spectrum analysis. The trend and frequency domain aspects of the dynamic forces were evaluated and discussed. The results indicate that a characteristic frequency in cutting force power spectrum does in fact exist. The amplitudes increase with the increase of cutting speed and tool wear level, which could be applied to the monitoring of the cutting process.