Development and Application of Die-Casting High Speed Steel Rolls

Due to its high hardness,good red hardness and excellent wear resistance at high temperature,high speed steel(HSS)is fit for the roll manufacture.In order to overcome the segregation of centrifugal casting of HSS roll,die-cast processes were developed and its effects on the properties of the HSS roll were investigated.It was found that pressure,pressing time and speed are three important factors affecting shrinkage cavity.For pouring temperature of 1 400-1 450 ℃,pressure of 150-160 MPa,pressing time of 120-150 sand pressing speed of 14-16mm/s,a compact HSS roll was obtained,which has no segregation and small working allowance.In the high speed wire rod rolling mill,service life of the HSS roll is 5to 8times longer than that of high nickel chromium infinite chilled cast iron roll.

Study on Key Joining Technology and Test Method of Steel/Al Hybrid Structure Body-in-White

Green and low carbon promote the application and development of light-weight materials in body-in-white. Large-scale die-casting Al alloy (DCAA) and high-strength thermo-formed steel sheet (TFSS) have put forward higher requirements for the application of joining technology of high-strength steel/Al dissimilar materials. Taking the new die-casting Al alloy body as an example, this paper systematically studies the progress of the latest joining methods of steel/Al dissimilar material with combination of two-layer plate and three-layer plate. By analyzing the joining technologies such as FSPR, RES, FDS and SPR, the technology and process characteristics of steel/Al dissimilar material joining are studied, and the joining technical feasibility and realization means of different material combination of the body are analyzed. The conditions of material combination, material thickness, material strength, flange height, preformed holes and joint spacing for achieving high-quality joining are given. The FSPR joining technology is developed and tested in order to meet with the joining of parts with DCAA and TFSS, especially for the joining of three-layer plates with them. It finds the method and technical basis for the realization of high quality joining of dissimilar materials, provides the early conditions for the application of large DCAA and TFSS parts in body-in-white, and meets the design requirements of new energy body. .

Effect of electromagnetic stirring in mold on the macroscopic quality of high carbon steel billet

An industrial plant trial for optimizing the process parameters in a round billet continuous casting mold with electromagnetic stirring （M-EMS） was performed, in which the influences of stirring parameters with M-EMS on the solidification macrostructure of high carbon steel were investigated. The results show that the billet quality is not well controlled under the condition of working current and frequency with EMS, in which the subsurface crack of grade 1.0-2.0 ups to 38.09%, the central pipe of grade 1.0-1.5 reaches to 14.28%, and the central porosity of grade 1.5 is 14.29%. The parameters of current 260 A and frequency 8 Hz as the final optimum scheme has a remarkable effect for improving the macroscopic quality of billet, in which the subsurface crack, central pipe and skin blowhole are all disappeared, and the central porosity and carbon segregation are also well improved.

Effect of CeO_2 on heat transfer and crystallization behavior of rare earth alloy steel mold fluxes

To improve the heat transfer capability and the crystallization property of the traditional mold flux, CaF_2 was replaced with B_2O_3. Then, the influences of CeO_2 on the heat transfer and the crystallization of the CaF_2-bearing mold flux and the new mold flux with 10 wt% B_2O_3 were studied using a slag film heat flux simulator and X-ray diffraction(XRD). The results revealed that the addition of CeO2 reduced the heat transfer by increasing the solid slag thickness and the crystallization of two mold fluxes. However, CeO_2 had less effect on the B_2O_3-containing mold flux compared with the CaF_2-bearing mold flux. According to the analyses, the CeO_2 contents in the CaF_2-bearing mold flux and the B_2O_3-containing mold flux should not exceed 8 wt% and 12 wt%, respectively. Therefore, these experimental results are beneficial to improve and develop the mold flux for casting rare earth alloy steels.

Effect of microstructure on the impact toughness of a bainitic steel bloom for large plastic molds

The correlation between the impact toughness and microstructural characteristics of a large bainitic steel bloom has been investigated. The study focuses on microcrack nucleation and propagation in the basic cleavage plane. To analyze the phase transformation during the wind-cooling process, the temperature field of the bloom was acquired by computer simulation, and a continuous cooling transformation experiment was conducted. The results show that compared with the surface of the bloom, the toughness of the bloom’s core is decreased by the increase in proeutectoid ferrite and the coarsening of tempered martensite–austenite constituents. The proeutectoid ferrite decreases the toughness via its effects on carbide precipitation, the formation of martensite–austenite constituents, and the bainite transformation. The relatively large tempered martensite–austenite constituents are conducive to microcrack nucleation and propagation.

Research on mold flux for hypo-peritectic steel at high casting speed

Mold fluxes having adaptable properties were developed in the laboratory to solve quality defects, such as depressions and longitudinal cracks when casting hypo-peritectic steel at high casting speed. Firstly, the effect of components on the high basicity mold flux properties was first studied using the orthogonal method. In the scope of the studied content, Li2O has the largest effect on the melting temperature, and the least effect on the viscosity; CaF2 has the largest effect on the viscosity, and the least effect on the melting temperature; Na2O and CaO/SiO2 have no obvious influence on the melting temperature and viscosity. Secondly, two powders （Z1 and Z6） have reasonable viscosity-temperature curves, higher solidification temperatures, and porous structure after solidification, but the crystal property of Z6 is worse than that of Z1, and thus Z1 is more suitable for continuous casting hypo-peritectic steel at high casting speed. Thirdly, a higher basicity of powder, a less free enthalpy of crystal compound, and a lower baffle energy are good for a higher tendentiousness of crystal.

Effect of Carbon Properties on Melting Behavior of Mold Fluxes for Continuous Casting of Steels

During continuous casting of steel, the properties of mold fluxes strongly affect the casting performance, steel quality and environment of casting operation. The high temperature microscopy technique was used to investigate the melting behaviour of mold fluxes, and drip test method was used to determine their melting rate. The results showed that free carbon is a dominant factor in governing the melting behaviour of fluxes, and the melting rate is increased with increasing carbon reactivity and decreasing carbon content.

Corrosion Behavior of the S136 Mold Steel Fabricated by Selective Laser Melting

The selective laser melting(SLM) method has a great potential for fabricating injection mold with complex structure. However, the microstructure and performance of the SLM molds show significantly di erent from those manufac?tured by traditional technologies. In this study, the microstructure, hardness and especially corrosion behavior of the samples fabricated by SLM and casting were investigated. The XRD results exhibit that the γ?Fe phase is only obtained in the SLM parts, and the α?Fe peak slightly moves to low di raction angle compared with casting counterparts. Due to the rapid cooling rate, the SLM samples have fine cellular microstructures while the casting ones have coarse grains with obvious elements segregation. Besides, the SLM samples show anisotropy, hardness of side view and top view are 48.73 and 50.31 HRC respectively, which are 20% higher than that of casting ones. Corrosion results show that the SLM samples have the better anti?corrosion resistance(in a 6% FeCl3 solution for 48 h) but the deeper corrosion pits than casting ones. Finally, the performance of the SLM molds could meet the requirement of injecting production. Moreover, the molds especially present a significant decrease(20%) of cooling time and increases of cooling uniform?ity due to the customized conformal cooling channels.

Low-cycle fatigue behavior of permanent mold cast and die-cast Al-Si-Cu-Mg alloys

Fatigue failure is one of the main failure forms of Al-Si-Cu-Mg aluminum alloys.To feature their mechanical aspect of fatigue behavior,the low-cycle fatigue behavior of permanent mold cast and die-cast Al-Si-Cu-Mg alloys at room temperature was investigated.The experimental results show that both permanent mold cast and die-cast Al-Si-Cu-Mg alloys mainly exhibit cyclic strain hardening.At the same total strain amplitude,the die-cast Al-Si-Cu-Mg alloy shows higher cyclic deformation resistance and longer fatigue life than does the permanent mold cast Al-Si-Cu-Mg alloy.The relationship between both elastic and plastic strain amplitudes with reversals to failure shows a monotonic linear behavior,and can be described by the Basquin and Coffin-Manson equations,respectively.

Preparation of high nitrogen and nickel-free austenitic stainless steel by powder injection molding

High nitrogen and nickel-free austenitic stainless steel has received much recognition worldwide because it can solve the problem of ＂nickel-allergy＂ and has outstanding mechanical and physical properties. In this article, 0Cr17Mn11Mo3N was prepared by powder injection molding （PIM） technique accompanied with solid-nitriding. The results show that the critical solid loading can achieve up to 64vol% by use of gas-atomized powders with the average size of 17.4 μm. The optimized sintefing conditions are determined to be 1300℃,2 h in flowing nitrogen atmosphere, at which the relative density reaches to 99% and the N content is as high as 0.78wt%. After solution annealing at 1150℃for 90 rain and water quench, the 0.2% yield strength, ultimate tensile strength （UTS）, elongation, reduction in area, and hardness can reach as high as 580 MPa, 885 MPa, 26.0%, 29.1%, and Hv 222, respectively.

Fabrication and sintering behavior of high-nitrogen nickel-free stainless steels by metal injection molding

高氮的没有镍的不锈钢被与各种各样的比例作为金属粉末和文件夹的 binders.Mixtures 用高氮 alloying 粉末和三聚合物的混合物塑造技术的金属注射制作也被调查，并且当64vol% .Intact 注射塑造了协议，装载能力的最佳粉末被决定被为塑造的协议调整处理 parameters.The debinding 过程成功地获得与 th

Rheological, mechanical and corrosive properties of injection molded 17-4PH stainless steel

The feedstock based on the binder 65%PW-30%EVA-5%SA has the best general rheological properties for the 17-4PH stainless steel powder. The 17-4PH stainless steel compacts sintered at 1 380 ℃ for 90 min have the best mechanical properties and the good microstructure with homogeneously distributed pore structure and the moderate-sized grains. Whereas the compacts sintered for 60 min and 120 min show an inadequate and an over-sintered microstructure respectively. The compacts sintered at 1380 ℃ for 90 min have the density of 7.70 g/cm^3, the strength of 1 275 MPa, the elongation of 5%, and hardness of HRC36. With the increase of sintering temperature, the density, strength and hardness increase, while the elongation decreases. The 17-4PH stainless steel has good corrosion resistance, showing an activation-passivation polarization curve. But the passivation potential range is narrow and the spot corrosion potential is low, indicating a low anti-spot corrosive properties.

Shape retention of injection molded stainless steel compacts

The effects of the binder composition, the powder loading, the thermal properties of feedstocks, and the injection molding parameters on the compact shape retention for metal injection molding 17-4PH stainless steel were investigated. The high-density polyethylene is more effective than ethylene vinyl acetate as a second component of the wax-based binder to retain compact shape due to its higher pyrolytic temperature and less heat of fusion. The compact distortion decreases with increasing the powder loading, molding pressure and molding temperature. There exists an optimal process combination including the powder loading of 68%, molding pressure of 120MPa and molding temperature of 150℃. Under this process condition, the percentage of distorted compacts is the lowest.

Behavior of Liquid Steel in Mold for Thin Slab Caster

The comparison of different submerged entry nozzles(SEN)was made by numerical simulation regarding the influence of liquid steel flow field,heat transfer and mold fluxes,as well as solidification shell stress and surface quality of thin slabs.The optimum internal shape of mold and the SEN were obtained.The foundation for choice of internal shape and casting parameters of mold was built.

Computer Aided Design of Heat Treatment for AISI P20+Ni Mold Steel with Good Machinability

Computer aided design of heat treatment for AISI P20 mold steel with good machinability is attempted to proceed by the commercial software package Thermo-Calc (TCP+DICTRA). Through experimental and theoretical analysis of phase transformation during heat treatment, further knowledge of designing proper heat treatment is obtained. Then the machinability of AISI P20+Ni steel under given heat treatment condition is studied and the influencing factors to their machinability are analyzed. It is shown that heat treatment designed by computer simulation of carbide transformation is applicable to AISI P20+Ni steel with good machinability; AISI P20+Ni steel with tempered sorbite treated by quenching & tempering has optimal machinability; normalizing at the temperature of 910°C & tempering can avoid cracking and result in acceptable machinability in small thickness module.

Simulation of thermal behavior during peritectic steel solidification in slab continuous casting mold

Thermal behavior of the solidifying shell in continuous casting mold is very important to final steel products.In the present work,one two-dimension transient thermal-mechanical finite element model was developed to simulate the thermal behavior of peritectic steel solidifying in slab continuous casting mold by using the sequential coupling method.In this model,the steel physical properties at high temperature was gotten from the micro-segregation model withδ/γtransformation in mushy zone,and the heat flux was obtained according to the displacement between the surface of solidifying shell and the hot face of mold as solidification contraction,the liquid-solid structure and distribution of mold flux,and the temperature distribution of slab surface and mold hot face,in addition,the rate-dependent elastic-viscoplastic constitutive equation was applied to account for the evolution of shell stress in the mold.With this model,the variation characteristics of surface temperature,heat flux, and growth of the solidifying shell corner,as well as the thickness distribution of the liquid flux,solidified flux,air gap and the corresponding thermal resistance were described.

Development and application of fluorine-free mold powder for low carbon steel

Fluorine in mold powder is known as harmful to human health and the environment. Being the advocate of green production, Baosteel developed an environmentally friendly mold powder without fluorine. The main problem of fluorine-free flux film is small heat resistance and thus the heat transfer intensity of the mold is too large, which to some extent hinders the increase of the casting speed. With the heat flow simulation equipment, controlling precipitation of crystal in flux and solidification temperature properly, fluorine-free mold powder for low carbon steel,which substitutes F with B203 ,was successfully developed and applied in industrial production. The production results show that, by using boronic fluorine-free mold powder,the boron increment in molten steel is less than 1.3ppm for conventional aluminium killed low carbon steel.

Sintering Mechanism of Stainless Steel in Powder Injection Molding

Stainless steel samples were made by Powder injection Molding (PIM) process with-400 mesh powder in order to investigate the sintering mechanism in this system and develop the PIM of stainless steels. The process included mixing, injection molding, debin- ding and sintering. Neck growth model was used to analyze the sintering mechanism. The results show that lattice (volume) diffusion is the main mechanism in the sintering process, the products with higher density (>95%) and properties are obtained. At lower temperatures, grain boundary diffusion may play a role in the sintering densification.

The optimization of mold fluxes used for casting the peritectic steel of heavy slabs at Baosteel

In order to solve the problem of the high surface longitudinal crack ratio of heavy peritectic steel slabs produced by the No. 3 continuous caster at Baosteel,the physical properties of the original mold flux and the optimized mold flux were compared in a comprehensive way by using analytical measures, such as a slag film heat-flow simulator, a thermowire molten flux crystallization tester and an X-ray diffractometer in the laboratory. The results reveal that one of the major reasons for the cracks is the poor heat transfer ability of the original mold flux. However, the optimized mold flux with a high basicity features a high crystallizing rate,low crystallization temperature and low heat-flow density. Therefore, the optimized mold flux is more suitable for casting peritectic steel by the heavy slab continuous caster. The test results show that the slabs produced by using the optimized mold flux had no surface longitudinal crack in four test casts, while the surface longitudinal crack ratio of the slabs produced by using the original mold flux was 5%. The optimized mold flux can effectively prevent slab surface longitudinal cracks from occurring.