Force and impulse multi-sensor based on flexible gate dielectric field effect transistor

Nowadays,force sensors play an important role in industrial production,electronic information,medical health,and many other fields.Two-dimensional material-based filed effect transistor(2D-FET)sensors are competitive with nano-level size,lower power consumption,and accurate response.However,few of them has the capability of impulse detection which is a path function,expressing the cumulative effect of the force on the particle over a period of time.Herein we fabricated the flexible polymethyl methacrylate(PMMA)gate dielectric MoS_(2)-FET for force and impulse sensor application.We systematically investigated the responses of the sensor to constant force and varying forces,and achieved the conversion factors of the drain current signals(I_(ds))to the detected impulse(I).The applied force was detected and recorded by I_(ds)with a low power consumption of~30 nW.The sensitivity of the device can reach~8000%and the 4×1 sensor array is able to detect and locate the normal force applied on it.Moreover,there was almost no performance loss for the device as left in the air for two months.

Alternative Strategy for Development of Dielectric Calcium Copper Titanate‑Based Electrolytes for Low‑Temperature Solid Oxide Fuel Cells

The development of low-temperature solid oxide fuel cells(LT-SOFCs)is of significant importance for realizing the widespread application of SOFCs.This has stimulated a substantial materials research effort in developing high oxide-ion conductivity in the electrolyte layer of SOFCs.In this context,for the first time,a dielectric material,CaCu_(3)Ti_(4)O_(12)(CCTO)is designed for LT-SOFCs electrolyte application in this study.Both individual CCTO and its heterostructure materials with a p-type Ni_(0.8)Co_(0.15)Al_(0.05)LiO_(2−δ)(NCAL)semiconductor are evaluated as alternative electrolytes in LT-SOFC at 450–550℃.The single cell with the individual CCTO electrolyte exhibits a power output of approximately 263 mW cm^(-2) and an open-circuit voltage(OCV)of 0.95 V at 550℃,while the cell with the CCTO–NCAL heterostructure electrolyte capably delivers an improved power output of approximately 605 mW cm^(-2) along with a higher OCV over 1.0 V,which indicates the introduction of high hole-conducting NCAL into the CCTO could enhance the cell performance rather than inducing any potential short-circuiting risk.It is found that these promising outcomes are due to the interplay of the dielectric material,its structure,and overall properties that led to improve electrochemical mechanism in CCTO–NCAL.Furthermore,density functional theory calculations provide the detailed information about the electronic and structural properties of the CCTO and NCAL and their heterostructure CCTO–NCAL.Our study thus provides a new approach for developing new advanced electrolytes for LT-SOFCs.

Degradation of Organic Compounds by Active Species Sprayed in a Dielectric Barrier Corona Discharge System

Investigation was made into the degradation of organic compounds by a dielectric barrier corona discharge （DBCD） system. The DBCD, consisting of a quartz tube, a concentric high voltage electrode and a net wrapped to the external wall （used as ground electrode）, was introduced to generate active species which were sprayed into the organic solution through an aerator fixed on the bottom of the tube. The effect of four factors-the discharge voltage, gas flow rate, solution conductivity, and pH of wastewater, on the degradation efficiency of phenol was assessed. The obtained results demonstrated that this process was an effective method for phenol degradation. The degradation rate was enhanced with the increase in power supplied. The degradation efficiency in alkaline conditions was higher than those in acid and neutral conditions. The optimal gas flow rate for phenol degradation in the system was 1.6 L/min, while the solution conductivity had little effect on the degradation.

Sintering,crystallization and dielectric properties of CaO-B_2O_3-SiO_2 system glass ceramics

CaO-B203-SiO2 （CBS） glass powders are prepared by conventional glass melting method at different melting temperatures whose properties and microstructures are characterized by X-ray diffraction （XRD） and scanning electron microscopy （SEM）. It is found that there are SiO2 and some unknown phases in CBS glass melting liquid from 1 300 ℃ to 1 500 ℃ and the amount of these phases decreases with the increase of the melting temperature. The CBS glass melted at 1 450 ℃ could be sintered from 830 ℃ to 930 ℃ and the bulk densities of the samples are all higher than 2.4 g/cm^3. From the points of the properties and energy conservation, the melting temperature of 1 450 ℃ is the optimal melting temperature. The glass ceramic sintered at 850 ℃ exhibits better dielectric properties： er=6.33, tan6=2.2×10^-3 at 10 GHz, and the major phases of the samples are CaSiO3, CaB2O4 and SiO2.

The Effect of Bi_2O_3 on the Structure and Microwave Dielectric Properties of Ba_(6-3x)Nd_(8+2x)Ti_(18)O_(54)System(x=2/3)

The structures and dielectric properties of Ba6-3xNd8＋2xTi18O54 system（x=2/3） doped with different contents of Bi2O3, whose final molecular formula is Ba6-3x（Nd1-yBiy）8＋2xTi18O54 were investigated. It is indicated that the dielectric constant increases greatly whereas Q value（f0=4 GHz） decreases with the increase of Bi2O3 content. However, the temperature coefficient could be controlled below 0±30×10^-6/℃ in the experiment. These phenomena are related to the appearance of a new phase, Bi4Ti3O12, which has high dielectric constant. Also, that Bi^3＋（0.13 nm） substitutes for Nd^3＋（0.099 5 nm） will increase the unit cell volume, which will lead to the enlargement of the octahedron B site occupied by Ti^4＋. So the spontaneous polarization of Ti^4＋ ions will be strengthened. Besides, Bi^3＋ will fill up some vacancies which Ba^2＋ or Nd^3＋ ions leave in two A1 sites and four A2 sites. More positive ions polarize, which also contributes to higher dielectric constant. The samples got with the optimium properties are sintered at 1 200 ℃ for 4 h, when y=0.25, ε≈110, Q≈5 400（f0=4 GHz）, TCC=-4.7×10^-6/℃; When y=0.3, ε≈120, Q≈5 000（f0=4 GHz）, TCC=-24×10^-6/℃.

Research on quinoline degradation in drinking water by a large volume strong ionization dielectric barrier discharge reaction system

Quinoline is widely used in the production of drugs as a highly effective insecticide,and its derivatives can also be used to produce dyes.It has a teratogenic carcinogen to wildlife and humans once entering into the aquatic environment.In this study,the degradation mechanism of quinoline in drinking water by a strong ionization dielectric barrier discharge(DBD)lowtemperature plasma with large volume was explored.High concentration of hydroxyl radical(·OH)(0.74 mmol l^(-1))and ozone(O3)(58.2 mg l^(-1))produced by strongly ionized discharge DBD system were quantitatively analyzed based on the results of electron spin resonance and O3 measurements.The influencing reaction conditions of input voltages,initial pH value,·OH inhibitors,initial concentration and inorganic ions on the removal efficiency of quinoline were systematically studied.The obtained results showed that the removal efficiency and TOC removal of quinoline achieved 94.8%and 32.2%,degradation kinetic constant was 0.050 min^(-1) at 3.8 k V and in a neutral pH(7.2).The proposed pathways of quinoline were suggested based on identified intermediates as hydroxy pyridine,fumaric acid,oxalic acid,and other small molecular acids by high-performance liquid chromatography/tandem mass spectrometry analysis.Moreover,the toxicity analysis on the intermediates demonstrated that its acute toxicity,bioaccumulation factor and mutagenicity were reduced.The overall findings provided theoretical and experimental basis for the application of a high capacity strong ionization DBD water treatment system in the removal of quinoline from drinking water.

Treatment of Practical Dye Wastewater Using a Double Dielectric Barrier Discharge System Combined with a Sequencing Batch Reactor System

Synthetic dyes are substances that are relatively stable and difficult to degrade in wastewater treatment plants using normal physical,chemical or / and biological treatment. The present work explored the synergistic effect of non-thermal plasma( NTP) and biological wastewater treatment technologies on practical dye wastewater degradation by establishing a double dielectric barrier discharge( DDBD) system combined with a sequencing batch reactor( SBR) system. The biodegradation and degradation efficiency of the DDBD-SBR system was investigated. The investigation results indicated that the DDBD technology was effective in treating the practical dye wastewater as a pre-treatment process. After a 10-min treatment,although the total organic carbon( TOC) removal efficiency was not so significant, the decolouration and the biodegradation were improved greatly. The microbial toxicity test revealed that the sample after degradation became less toxic than the original dye,which demonstrated the treatment had a significant effect on the reduction of toxicity. In addition,the SBR technology remedied the defects of DDBD treatment and improved TOC removal efficiency noticeably. The hybrid DDBD-SBR system made full use of the advantages of the individual technologies and exhibited an efficient capability for practical dye wastewater treatment.

Dielectric Spectroscopy Study on Vesicles of CTAB/SDBS System

Amphiphilic molecules can form into different structures, such as micelle, microemulsion, vesicle, liposome, liquid crystals, and so on by self-associating. The Dielectric Spectroscopy (DS) method has been applied to the systems of micelle and microemulsion successfully. For the first time the author put the method to the system of vesicle of CTAB/SDBS. The experiments show clear dielectric relaxation and the results were discussed primarily.

Ultrahigh performance passive radiative cooling by hybrid polar dielectric metasurface thermal emitters

Real-world passive radiative cooling requires highly emissive,selective,and omnidirectional thermal emitters to maintain the radiative cooler at a certain temperature below the ambient temperature while maximizing the net cooling power.Despite various selective thermal emitters have been demonstrated,it is still challenging to achieve these conditions sim-ultaneously because of the extreme difficulty in controlling thermal emission of photonic structures in multidimension.Here we demonstrated hybrid polar dielectric metasurface thermal emitters with machine learning inverse design,en-abling a high emissivity of~0.92 within the atmospheric transparency window 8-13μm,a large spectral selectivity of~1.8 and a wide emission angle up to 80 degrees,simultaneously.This selective and omnidirectional thermal emitter has led to a new record of temperature reduction as large as~15.4°C under strong solar irradiation of~800 W/m2,signific-antly surpassing the state-of-the-art results.The designed structures also show great potential in tackling the urban heat island effect,with modelling results suggesting a large energy saving and deployment area reduction.This research will make significant impact on passive radiative cooling,thermal energy photonics and tackling global climate change.

Effect of La_2O_3-Dopant on Microstructure and Microwave Dielectric Properties of CaO-MgO-Nb_2O_5-TiO_2 System Ceramics

La_2O_3-doped CaO-MgO-Nb_2O_5-TiO_2 system ceramics were prepared by solid-state ceramic technique. The microstructure and microwave dielectric properties of CaO-MgO-Nb_2O_5-TiO_2-La_2O_3 ceramics can be adjusted by varying the amount of La^(3+) ions. The results show that the replacement of Ca^(2+) by La^(3+) at A-site of the ceramics can increase the quality factor Q·f value as well as the temperature coefficient of resonant frequency τ_f and decrease the dielectric constant ε_r. With increase of La^(3+) contents, the dielectric constant decreases from 57 to 35 and Q·f value increases from 33400 GHz to 35000 GHz (at 7.6 GHz). Meanwhile, the temperature coefficient of resonant frequency is improved towards near zero. The dielectric properties of these compounds are related to octahedra tilting due to deficient vacancies at A-site.

Effect of La^(3+), Sr^(2+) on Microwave Dielectric Properties of CaO-MgO-Nb_2O_5^-TiO_2 System Ceramics

The effect of La^3 ＋ , Sr^2＋ on the microstructure and microwave properties of CaO-MgO-Nb2O5-TiO2 system ceramics was investigated. The result shows that a single complex perovskite structure formed within investigated composition range in La^3＋ , Sr2-doped CaO-MgO-Nb2O5-TiO2 system ceramics. With increasing of La^3＋ , Sr^2＋ content, the structure of La^3＋ , Sr2-doped CaO-MgO-Nb2O5-TiO2 system ceramic respectively maintain orthorhombic type.

A Preliminary Study of Dielectric Properties and Structures of NBT-SCN System

ＡＰｒｅｌｉｍｉｎａｒｙＳｔｕｄｙｏｆＤｉｅｌｅｃｔｒｉｃＰｒｏｐｅｒｔｉｅｓａｎｄＳｔｒｕｃｔｕｒｅｓｏｆＮＢＴ┐ＳＣＮＳｙｓｔｅｍＴａｎｇＹｉｗｅｎ，ＤａｉＭｉｎｇｘｉｎｇ，ＷａｎｇＲｅｎｈｕｉ，ＧｕｉＪｉａｎｉａｎＤｅｐａｒｔｍｅｎｔｏｆＰｈ...

Preparation,Structure and Dielectric Properties of Tungsten Bronze Ferroelectrics in SrO-Eu_2O_3-TiO_2-Nb_2O_5 System

Compounds Sr4Eu2Ti4Nb6O30 and Sr5EuTi3Nb7O30 with filled tetragonal tungsten bronze structure were prepared,and the dielectric characteristics and ferroelectric transition were investigated.Both ceramics displayed weak frequency dependence in room temperature dielectric constant,which decreased from 125 to 118 for Sr4Eu2Ti4Nb6O30,from 206 to 195 for Sr5EuTi3Nb7O30 in the frequency range of 10 kHz to 1 MHz.The present ceramics showed a diffuse ferroelectric phase transition.The frequency independent transition temperature （Tm） indicated the above compounds had no relaxor property.The diffuseness （γ） was 1.45 and 1.64 for Sr4Eu2Ti4Nb6O30 and Sr5EuTi3Nb7O30 respectively.The weak ferroelectric of the present materials are indicated from the P-E hysteresis loops,and a small 2Pr of 0.596 μC/cm2 and 0.068 μC/cm2 were observed for Sr4Eu2Ti4Nb6O30 and Sr5EuTi3Nb7O30 respectively.

An Investigation of Structure Transition in Sodium Dodecyl Trioxyethylene Sulfate/n-Butanol/n-Octane/Water System by Dielectric Relaxation Spectroscopy Method

The phase diagram of the quaternary system of sodium dodecyl trioxyethylene sulfate(SDES)/n-butanol/n-octane/water was obtained at (30.0±0.1) ℃. There exists a clear, isotropic, and low-viscosity L phase, which can be divided into W/O, bi-continuous(B.C.) and O/W microemulsions by conductivity measurement results. Dielectric Relaxation Spectroscopy(DRS) measurements, including permittivity, conductivity, relaxation strength, characteristic relaxation time, dielectric parameters, phase parameters, etc., were applied to investigating the microstructures of the system mentioned above. For the samples with a fixed SDES/n-butanol mass ratio of 4/6 including 20%(mass fraction) of n-octane, DRS indicated a structure transition from a W/O to an O/W via a B.C. microemulsion with the increase of the water content. For the samples with a fixed (SDES/20%n-octane)/H_2O mass ratio of 5/5, DRS presented that there only exists a onefold structure of a W/O microemulsion as the (n-butanol/20%n-octane) content increases. The results obtained from DRS are in good agreement with those from the phase diagram.

Dielectric Properties of B_2O_3 Doped MgTiO_3-CaTiO_3 System Ceramics

The dielectric ceramics with a main crystal phase of MgTiO 3 and additional crystal phase of CaTiO 3 were prepared by the conventional electronic ceramics technology. The structures of MgTiO 3 are ilmenite-type, and belong to hexagonal syngony. The ratio of MgTiO 3 to CaTiO 3 can be adjusted to gain a zero temperature coefficient of ε r and a higher ε r for the system. The effects of B 2O 3 doping on the dielectric properties of MgTiO 3-CaTiO 3 (MCT) ceramics were investigated. The addition of B 2O 3 decreases the sintering temperature and results in rapid densification without obvious negative effect on the Q values of the system (Q=1/tan δ). B 2O 3 exists as liquid phase in the sintering process, promoting the reactions as a sintering agent.

Effect of Rare Earth Oxides on the Microstructure and Microwave Dielectric Properties of CaO-MgO-Nb_2O_5-TiO_2 System Ceramics

La2O3 and SrO-doped CaO-MgO-Nb2O3-TiO2 system ceramics were prepared by solid-state ceramic technique.The microstructure and microwave dielectric properties of CaO-MgO-Nb2O5-TiO2-La2O3 cermics can be adjusted by varying the amount of La^3＋ or Sr^2＋ ions respectively.The replacement of Ca^2＋ by La^3＋ at A-site of the ceramics increases the quality factor Q value（ at 7.6GHz）as well as the temperature coefficient of resonant frequency τf and decreases the dielectric constant εr and the substitution of Sr^2＋ at A-site in this ceramics system exhibits opposite characteristics.The microwave properties of La^3＋,Sr^2＋-doped CaO-MgO-Nb2O5-TiO2 system ceramics depend on the degree of octahedral distortion inside materials.

Structure and Dielectric Properties of ZnO and Nb_2O_5 Doped BaO-TiO_2 System Microwave Ceramics

The microwave dielectric properties and microstructure of BaTi4.3ZnyO9.6＋y ＋0.02 mol% SnO2＋0.01 mol% MnCO3＋x mol% Nb2O5（x=0-0.05, y=0-0.08） system ceramics were studied as a function of the amount of ZnO and Nb2O5 doped. Addition of （y=0-0.05） ZnO and （x=0-0.025） Nb2O5 enhanced the reactivity and decreased the sintering temperature effectively. It also increased the dielectric constant ε r and quality factor Q（=1/tan 8） of the system due to the substitution of Ti^4＋ ions with incorporating Zn^2＋and Nb^5＋ ions, which was analyzed by the reaction ZnO＋Nb2O5＋ 3 TiTxTi →ZnTi＋ 2NbTi＋3TiO2. When the system doped with （y=0.05） ZnO and （x=0.025） Nb205 were sintered at 1 160 ℃ for 6 h, the εr. Qf0 value and rfwere 36.5, 42 000 GHz, and＋1.8 ppm/℃, respectively, at 5 GHz.

Analysis of the critical active species for methylene blue decoloration in a dielectric barrier discharge plasma system

In the paper, a hybrid gas–liquid dielectric barrier discharge(DBD) plasma system was set up to treat a methylene blue(MB) solution. The effects of the change of the carrier gas, the gas bubbling rate and different kinds of scavenger addition, including sodium carbonate(Na_2CO_3),para benzoquinone(p-BQ), triethylenediamine and sodium dihydrogen phosphate(NaH_2PO_4),on the MB decoloration were reviewed to clarify the critical active species for the dye decoloration in the DBD plasma system. The obtained results show that higher decoloration of the MB solution could be achieved when O2 was used as the carrier gas, which could be 100% after 20 min discharge treatment, and the result confirmed the crucial effect of O_3 in the MB decoloration. Based on the experiments of the scavenger addition, it could be concluded that O_2·^- and ~1O_2 were two other important reactive oxygen species(ROS) for the MB decoloration.The results of the higher chemical oxygen demand removal and faster disappearance of the characteristic peak of the MB from the UV–vis analysis under O_2 bubbling conditions also proved the critical effect of the ROS formed by O_2 on the MB decoloration.

Dielectric Spectra of Aerosol OT/Water Systems at Different Concentrations and Temperatures

The dielectric spectra of aerosol OT[AOT, sodium（bis-2-ethylhexyl）sulfosuccinate]/water systems at different concentrations and temperatures were investigated by the dielectric relaxation spectroscopy（DRS）. Through the dielectric spectra of different concentrations, two dielectric relaxations were observed over a frequency range from 40 Hz to 110 MHz and the mechanisms of the relaxations were also interpreted based on the Grosse’s model. The low-frequency relaxation（around 105 Hz） was attributed to the radial diffusion of counterions along the long-half axis of the rod-like micelle, and the high-frequency relaxation（around 106 Hz） was ascribed to the radial diffusion of counterions along the short-half axis. Furthermore, specific emphasis was placed on studying the effects of temperature on system’s conductivity. It was observed that the low-frequency limit of conductivity（κl） decreased and then increased with the increment of temperature under the measured concentration. On the other hand, the conductivity（κm and κh） in meso- and high-frequency ranges always increased as temperature increased. Both the tendencies of alteration which mentioned above should be related to the phase transition of AOT/water system.

Dielectric Properties at High Frequency of BSTO System Doped Dy_2O_3

Samples doped with different amount of dysprosium oxide into barium strontium titanate (BSTO) were prepared. Dielectric properties of the samples at high frequency were discussed. X-ray diffraction (XRD) method was employed for analyzing and comparing with the changes in the crystal lattice of the samples,and information of crystal growth was obtained through method of environmental scanning electron micrograph (ESEM). Influence of dysprosium oxide doping on dielectric properties of BSTO based ceramic system at high frequency was studied. Phenomenological coefficients of the samples were calculated on the base of tunability.