Evaluation of the Oxidation Reactivity and Behavior of Exhaust Soot Particles from Diesel Engines with Different Emission Levels

The aim of this study was to investigate the oxidation reactivity and behavior of exhaust particulate matter(PM)from diesel engines.PM samples from two diesel engines(1K,CY4102)with different emission levels were collected by a thermophoretic system and a quartz filter.The oxidation reactivity,oxidation behaviors,and physicochemical properties of the PM samples were analyzed using thermogravimetric analysis(TGA),high-resolution transmission electron microscopy(HRTEM),Fourier-transform infrared spectrometry(FTIR),and Raman spectroscopy.The results showed that there was a great difference in the oxidation reactivity of soot particles emitted by the two different diesel engines.A qualitative analysis of the factors influencing oxidation reactivity showed that the nanostructure,degree of graphitization,and relative concentration of aliphatic C—H functional groups were the most important factors,whereas no significant correlation was found between the primary particle size and activation energy of the diesel soot.Based on the oxidation behavior analysis,the diesel soot particles exhibited both internal and surface oxidation modes during the oxidation process.Surface oxidation was dominant during the initial stage,and as oxidation progressed,the mode gradually changed to internal oxidation.Internal oxidation mode of soot particles from the 1K engine was significantly higher than that of CY4102.

Combined Effect of a Catalytic Reduction Device with Waste Frying Oil-Based Biodiesel on NOx Emissions of Diesel Engines

Internal combustion engines with application in automobiles and other relevant industries constitute significant environmental pollution via the release of toxic exhaust gasses like carbon monoxide (CO), hydrocarbons (HC), particulate matter (PM), and nitrogen oxide (NOx). Engine researchers and manufacturers are challenged to develop external and internal measures to ensure environmentally friendly solutions to accommodate and conform to the growing list of emission standards. Therefore, this work presents an experimental investigation of the NOx emission profile of a diesel engine that is fuelled and fitted with waste frying oil-based biodiesel and catalytic converter. Using a single-cylinder, four-stroke air-cooled CI engine at a constant speed of 1900 rpm and different loadings of 25%, 50%, 75%, and 100%;fitted with a catalytic converter at the exhaust outlet of the engine and linked to a dynamometer and a gas analyser, an experiment was conducted at biodiesel/diesel volume blends of B0 (0/10), B5 (5/95), B20 (20/80), B30 (30/70), B70 (70/30), B100 (100/0);and 30% concentration (v/v), 0.5 litre/hr flow rate of aqueous urea from the catalytic converter. The results show an increasing NOx emission as the biodiesel component increased in the blend. The catalytic converter showed a downward NOx reduction with a significant 68% reduction in efficiency at high exhaust gas temperatures. It is concluded that the combined utilisation of waste frying oil-based biodiesel and the catalytic converter yields substantial NOx emission reduction.

Effects of Hydrogen Addition on Power and Emissions Outputs from Diesel Engines

Energy efficiency and environmental impact have become dominant topics in internal combustion engines development. Among many strategies to improve power and emissions outputs from diesel engines is the partial mix of hydrogen and air as fresh charge components to form extremely lean and homogenous mixture, which resist the spontaneous combustion, while diesel fuel is injected directly inside combustion chamber using the conventional fuel injection systems. This contribution presents an analytical and experimental investigation for the effects of adding hydrogen on diesel engines power output and the reduction of emissions. Parametric analysis is used based on lamped parameters modeling of intake manifold to estimate in cylinder trapped charge. The fuel energy flow to engine cylinders is compared for a range of loads and concentrations to simulate relevant case studies. Diesel fuel reduction for significant range of part-load operation can be achieved by introducing hydrogen, along with power improvement emission reductions are affected positively as well. This is achievable without compromising the engine maximum efficiency, given that most engines are operated at small and part-load during normal driving conditions, which allow for introducing more hydrogen instead of large quantities of excess air during such operation conditions that also can be further improved by charge boosting.

A Database of Selected Marine Diesel Engines for Diagnostic Needs

The article describes an electronic database of selected marine piston combustion engines created for diagnostic purposes. The database was made for vessels of the biggest Polish shipowner. It is used for archiving and comparing measured parameters of diagnosed engines with model parameters. To facilitate the search for and use of required data, they have been collected and catalogued. For this purpose the database has been prepared by using a computer program included in the Microsoft Office suite. The database search relies on the details concerning the type of vessel. The fields displayed include such items as the year and place of construction, the parameters of the ship, flag, etc.. For each vessel special forms are available for main and auxiliary engines, enabling easy and quick check of the necessary parameters during operation of the engine. The database contains parameters of the main propulsion and auxiliary engines, as well as model characteristics to help determine the diagnostics, prognosis and genesis.

Series 190 Diesel Engines Used in China's Oil Drilling

Ｓｅｒｉｅｓ１９０ＤｉｅｓｅｌＥｎｇｉｎｅｓＵｓｅｄｉｎＣｈｉｎａ＇ｓＯｉｌＤｒｉｌｌｉｎｇ￥／／ＬｉｕＱｉｍｉｎ（ＣｈｉｅｆＥｎｇｉｎｅｅｒ．ＪｉｎａｎＤｉｅｓｅｌＥｎｇｉｎｅＷｏｒｋｓ）ＪｉｎａｎＤｉｅｓｅｌＥｎｇｉｎｅＷｏｒｋｓ，ｌｏｃａｔｅｄ...

Optimization of the Performance of Marine Diesel Engines to Minimize the Formation of SO_x Emissions

Optimization procedures are required to minimize the amount of fuel consumption and exhaust emissions from marine engines.This study discusses the procedures to optimize the performance of any marine engine implemented in a 0D/1D numerical model in order to achieve lower values of exhaust emissions.From that point,an extension of previous simulation researches is presented to calculate the amount of SOx emissions from two marine diesel engines along their load diagrams based on the percentage of sulfur in the marine fuel used.The variations of SOx emissions are computed in g/k W·h and in parts per million(ppm)as functions of the optimized parameters:brake specific fuel consumption and the amount of air-fuel ratio respectively.Then,a surrogate model-based response surface methodology is used to generate polynomial equations to estimate the amount of SOx emissions as functions of engine speed and load.These developed non-dimensional equations can be further used directly to assess the value of SOx emissions for different percentages of sulfur of the selected or similar engines to be used in different marine applications.

HC-PM COUPLING MODEL FOR PARTICULATE MATTER EMISSION OF DIESEL ENGINES

A rapid, phenomenological model that predicts paniculate matter (PM) emissionof diesel engines is developed and formulated. The model is a chemical equilibrium compositionmodel, and is based on the formation mechanisms of PM and unburned hydrocarbon (HC) emissions ofdiesel engines. It can evaluate the emission concentration of PM via the emission concentration ofHC. To validate the model, experiments are carried out in two research diesel engines. Comparisonsof the model results with the experimental data show good agreement. The model can be used toevaluate the concentration of PM emission of diesel engines under lack of PM measuring instruments.In addition, the model is useful for computer simulations of diesel engines, as well as electroniccontrol unit (ECU) designs for electronically controlled diesel engines.

Experimental Study on the Performance and Emission of Chinese Small Agricultural Diesel Engine Fuelled with Methanol/Biodiesel/DTBP

Diesel engine alternative fuels, such as methanol and biodiesel, are beneficial to reduce diesel engine emission. In order to study the influence of methanol and biodiesel on the performance, economy and emission of small agricultural diesel engine, the physical-chemical properties(cetane number, lower heat value(LHV), viscosity, etc.) of methanol and biodiesel were analyzed. The methanol and biodiesel showed good complementary property to some extent. When a large proportion of methanol was added into biodiesel, the cetane number of the methanol/biodiesel blend will be greatly reduced. Since the cetane number of the blend fuel has great influence on the combustion process of diesel engine, after testing for blending ratio of methanol/biodiesel, the blend was prepared with 5%(BM5), 10%(BM10) and 15%(BM15) methanol, respectively. Di-Tert-Butyl Peroxide(DTBP) was chosen as a cetane number improver to be added into methanol/biodiesel blend. 0.25%, 0.50% and 0.75% of DTBP was added into BM15. The bench test was carried out on a 186 FA diesel engine to study the effect of methanol and DTBP on the engine performance and emissions. The results show that, at rated condition, compared with biodiesel, the NO;concentration of BM5, BM10 and BM15 is reduced by 5.02%, 33.85% and 21.24%, and smoke is reduced by 5.56%, 22.22% and 55.56%. However, the engine power is also reduced by 5.77%, 14.23% and 25.41%, and the brake specific energy consumption is increased by 3.31%, 7.78% and 6.37%. The addition of DTBP in methanol/biodiesel could recover the engine power to the level of diesel. DTBP shows good effect on the reduction of the brake specific energy consumption and NO_(x), CO, HC concentration, but a little increase of exhaust smoke.

Hardware-in-the-Loop Research on the Electronic Control Unit for Diesel Engines

A hardware-in-the-loop simulating platform is developed to avoid designing defects caused by the complicated logical structure and multiple-functional buildup of the dectronic control unit（ECU）in modem diesel engines, and to diminish potential damages on components or human exposure to dangers in R＆D en- deavor. This plat-form consists of a computer installed with software Matlab/Simulink/RTW and dSPACE/ ControlDesk; a diesel engine ECU, and a dSPACE autobox which runs a real-time diesel engine model. A typical model of diesel engine with turbocharger and intercooler is presented. Based on this model our research is carried out with a real ECU to test its software control strategies. Results show that by using the diesel engine model downloaded inside, the hardware-in-the-loop platform can simulate diesel engine＇s working conditions and generate all kinds of sensor signals which ECU needs on a real-time basis. So the ECU control strategies can be validated and relevant parameters roughly calibrated.

Optimal Mixture Ratios of Biodiesel Ethanol Diesel for Diesel Engines

In this paper, we study the best-mixture ratio of biodiesel-ethanol-diesel for diesel engines. The simulation results show that the integrated indexes including engine power, cost-effectiveness and emission properties are rather better with different optimizing index when the ratio of bio-diesel, ethanol and diesel are 71.58:2.72:25.70 and 50:2.4127:47.5873.

Optimizing the Exhaust System of Marine Diesel Engines to Improve Low-speed Performances and Cylinder Working Conditions

Proper design of exhaust systems in marine high-power turbocharged diesel engines can contribute to improve the low-speed performance of these engines and make the working conditions of the cylinders more uniform.Here a high-power marine 16-cylinder V-type turbocharged diesel engine is simulated using the GT-Power software.The results reveal the differences induced by different exhaust system structures,such as an 8-cylinder-inpipe exhaust system with single/double superchargers and a 4-cylinder-in-pipe exhaust system with a single supercharger.After a comparative analysis,the 8-cylinder type with double superchargers is determined to be the optimal solution,and the structure of the exhaust system is further optimized.The simulations show that the optimized maximum exhaust temperature difference among cylinders is reduced by 66%.Finally,the simulation results and the optimized performance of the designed exhaust system are verified through experiments.

Miller Cycle with Early Intake Valve Closing in Marine Medium-Speed Diesel Engines

In this study,a one-dimensional simulation was performed to evaluate the performance of in-cylinder combustion to control NO_(x) emissions on a four-stroke,six-cylinder marine medium-speed diesel engine.Reducing the combustion temperature is an important in-cylinder measure to decrease NO_(x) emissions of marine diesel engines.The Miller cycle is an effective method used to reduce the maximum combustion temperature in a cylinder and accordingly decrease NO_(x) emissions.Therefore,the authors of this study designed seven different early intake valve closing(EIVC)Miller cycles for the original engine,and analyzed the cycle effects on combustions and emissions in high-load conditions.The results indicate that the temperature in the cylinder was significantly reduced,whereas fuel consumption was almost unchanged.When the IVC was properly advanced,the ignition delay period increased and the premixed combustion accelerated,but the in-cylinder average pressure,temperature and NO_(x) emissions in the cylinder were lower than the original engine.However,closing the intake valve too early led to high fuel consumption.In addition,the NO_(x) emissions,in-cylinder temperature,and heat release rate remarkably increased.Therefore,the optimal timing of the EIVC varied with different loads.The higher the load was,the earlier the best advance angle appeared.Therefore,the Miller cycle is an effective method for in-engine NO_(x) purification and does not entail significant cost.

Assessment of the Application of Subcooled Fluid Boiling to Diesel Engines for Heat Transfer Enhancement

The increasing demand of cooling in internal combustion engines(ICE)due to engine downsizing may require a shift in the heat removal method from the traditional single phase liquid convection to the application of new technologies based on subcooled fluid boiling.Accordingly,in the present study,experiments based on subcooled flow boiling of 50/50 by volume mixture of ethylene glycol and water coolant(EG/W)in a rectangular channel heated by a cast iron block are presented.Different degrees of subcooling,velocity and pressure conditions are examined.Comparison of three empirical reference models shows that noticeable deviations occur especially when low bulk subcooling and velocity conditions are considered.On the basis of the experimental data,a modified power-type wall heat flux model is developed and its ability to represent adequately reality is tested through numerical simulations against a reference rig case and a practical diesel engine.Computational results show that this modified model can effectively be used for practical engine cooling system design.

Dispersion Performance of Methanol-Diesel Emulsified Fuel Prepared by High Gravity Technology

A new continuous process for preparing methanol-diesel emulsified fuel with an Impinging Stream-Rotating Packed Bed is proposed. The droplet size of dispersed phase(methanol) of the emulsified fuel has a significant effect on the combustion of methanol-diesel emulsified fuel. In this paper, the methanol-diesel emulsified fuel uses diesel as the continuous phase and methanol as the dispersed phase. The Sauter mean diameter of the dispersed phase of methanol-diesel emulsified fuel was characterized with microphotography and arithmetic method. The experimental result showed that the Sauter mean diameter of the dispersed phase, which was decreased with the augmentation of the high gravity factor, liquid flow rate and emulsifier dosage, was inversely proportional to the methanol content. The Sauter mean diameter of the dispersed phase can be controlled and adjusted in the range of 12—40 μm through the change of operating conditions. The correlative expressions of the Sauter mean diameter of emulsified fuel were obtained and the calculated values agreed well with the experimental values.

A New Method for Computing Radiation Heat Flow of In-Cylinder Soot of Diesel Engines

A concise formula for computing radiation heat flow of in-cylinder soot is presented, based on the assumptions that in-cylinder heat transfer of diesel engines is a quasi-equilibrium process and in-cylinder soot particles are spherical. That in this formula there consist neither constants needing adjustments nor variables related to engine types or operating conditions makes it universal and easy to use. Also it can be seen from the formula that radiation heat transfer is proportional to the quotient of in-cylinder soot mass over the average radius of primary particles. Besides, with the help of different algorithms it can be used for predicting cylinders＇ global as well as local radiation heat flows. As a demonstrative application on its global facet, a three-dimension simulation study about the soot-radiation-related heat flow in the combustion chamber of a diesel engine is carried out. Results show that the range of the soot-radiation-related heat flow computed by this formula agrees well with other researcher＇s earlier theoretic reasoning and experimental measurements.

A Review and Comparison on Recent Optimization Methodologies for Diesel Engines and Diesel Power Generators

The electrical instability that frequently distinguishes the isolated networks and depends on diesel generators to supply their energy requirements leads to an operation of the diesel generator in a transient dynamic condition and/or at low loads. In addition, extended operation of the diesel generator at partial load develops the condensation of combustion residues on the engine cylinder walls, which, after a certain time, increases friction, reduces the efficiency of the equipment and increases its fuel consumption. On the other hand, recent regulatory changes have led to ever more stringent and evolving emission standards. Among these, the International Maritime Organization (IMO) and the Environmental Protection Agency (EPA) have implemented emission standards in order to reduce exhaust gas emitted by marine diesel engines. To phase lower emission engines as soon as possible, a Tier system was adopted. This paper presents a literature review of existing technologies available to optimize the energy performance of diesel engines and diesel generators in order to reduce the cost of electricity, to increase the diesel engine efficiency and to decrease their fuel consumption and greenhouse gases (GHG) emissions. The proposed optimization methodologies are based on the application of Pre-treatment, Internal treatment and Post-treatment technologies for diesel engines and on the application of mechanical and electrical technologies for diesel power generators (DPGs). The list of references given at the end of the paper should offer aids for students and researchers working in this field.

An Evaluation of Human Error Probabilities for Critical Failures in Auxiliary Systems of Marine Diesel Engines

Human error,an important factor,may lead to serious results in various operational fields.The human factor plays a critical role in the risks and hazards of the maritime industry.A ship can achieve safe navigation when all operations in the engine room are conducted vigilantly.This paper presents a systematic evaluation of 20 failures in auxiliary systems of marine diesel engines that may be caused by human error.The Cognitive Reliability Error Analysis Method(CREAM)is used to determine the potentiality of human errors in the failures implied thanks to the answers of experts.Using this method,the probabilities of human error on failures were evaluated and the critical ones were emphasized.The measures to be taken for these results will make significant contributions not only to the seafarers but also to the ship owners.

Evaluation of properties for lubricant filter in diesel engines

The properties of lubricant filters in diesel engines directly affect operation of the lubricant system, and lubricant filters are apt to be impacted by many factors. Therefore, scientific and sensible methods evaluating the properties for lubricant filter diesel engines are necessary to monitor filter properties on line and dynamically. This paper applies ferrographic techniques and adopts sampling methods that oil specimens are synchronously obtained in front of and behind filter elements to monitor the filters of ISUZU DA-220 diesel engine in two FD50 forklifts. Results show that the combination of ferrographic techniques and above sampling methods is effective in analyzing the whole operating process of filters used in diesel engines. The service life and ruined type of filter can be estimated through the relationship between ferrographic readings in front and behind of filter and operation time. Furthermore, through a great deal of tests, a series of experimental curves of readings and time and characteristic parameters for filters used in different machines can be gained, which has guiding significance to the selection and maintenance of the filters. But because of the limitation of the ferrographic technique, the debris on the substrate prevents determination of sizes. It is difficult to judge accurately the size of debris that a filter can filter.

Dynamic Characteristic Investigation on the Fuel Pressure of Diesel Engines Electronic In-line Pump System

The electronic in-line pump (EIP) is a complex system consisting of mechanical, hydraulic, and electromagnetic parts. Experimental study showed that the fuel pressure of the plunger and the fuel drainage of the pressure system after fuel injection could result in fuel pressure fluctuation in the low pressure system. Such fluctuation exhibited pulsating cycle fluctuation as the amplitude rose with the increase of the injection pulse width. The time domain analysis found that the pressure time history curve and injection cylinders corresponded with a one-to-one relationship. By frequency domain analysis, the result was that with the increase of the working cylinder number, the high frequency amplitude gradually increased and the basic frequency amplitude gradually decreased. The conclusion was that through wavelet transformation, the low pressure signal simultaneously moved towards low frequency as the high frequency of the wavelet transformation signal with the working cylinder number increased. Lastly, by using the numerical model, the study investigated the simulation research concerning the relationship of the fluctuation dynamic characteristic in the low pressure system and the fuel injection characteristic of the high pressure system, completing the conclusions obtained by the experimental study.

Detection of cylinder pressure in diesel engines using cylinder head vibration and time series methods

This paper investigates the vibration characteristics of diesel engine cylinder heads by means of the time series method. With the concept of "Assumed System",the vibration transfer function of real cylinder head structures is established using the autoregressive-moving average models(ARMA models) of cylinder head surface vibration signals. Then this transfer function is successfully used to reconstruct the gas pressure trace inside the cylinder from measured cylinder head vibration signals. This offers an effective means for diesel engine cylinder pressure detection and condition monitoring.