Buck Converter Current Measurement Using Differential Amplifier

The accuracy of the measured current is a preeminent parameter for Current Control based Power Converter applications to ensure genuine operation of the designed converter.The current measurement accuracy can be affected by several parameters which includes the type of technology used,components used for the selected technology,aging,usage,operating and environmental conditions.The effect of gain resistors and their manufacturing tolerances on differential amplifier-based buck converter current measurement is investigated in this work.The analysis mainly focused on the output voltage variation and its accuracy with respect to the change in gain resistance tolerances.The gain resistors with 5%,1%,0.5%and 0.1%manufacturing tolerances taken for the worst-case analysis and the calculated performance results are compared and verified with the simula-tion results.The Operational amplifiers(Op-Amp)for high frequency power con-verter applications must operate in a high frequency noise environment and the intended current measuring system must manage common mode noise distur-bances paired with the signal to be measured.Based on the Common Mode Rejec-tion Ratio(CMRR)the common mode voltages and noise signals will effectively getfiltered out.Lesser CMRR results in lower common mode signal rejection,resulting in poor precision and noise rejection.In differential amplifiers,the CMRR predominantly depends on gain resistors.So,the variations in Common Mode Rejection Ratio due to gain resistor tolerances also analyzed and compared with the output voltage variations.Besides the effects of resistor tolerances,this paper also examines the effect of Op-Amp offset voltage on output accuracy spe-cifically for low magnitude input currents.The obtained results from this analysis clearly shows that the gain resistors with 0.1%tolerance gives maximum accuracy with improved CMRR and accuracy at low magnitude input currents will get well improved by using Op-Amps with Low Offset voltage specifications.

Differential mode-gain equalization via femtosecond laser micromachining-induced refractive index tailoring

The mode-division multiplexing technique combined with a few-mode erbium-doped fiber amplifier(FM-EDFA)demonstrates significant potential for solving the capacity limitation of standard single-mode fiber(SSMF)transmission systems.However,the differential mode gain(DMG)arising in the FM-EDFA fundamentally limits its transmission capacity and length.Herein,an innovative DMG equalization strategy using femtosecond laser micromachining to adjust the refractive index(RI)is presented.Variable mode-dependent attenuations can be achieved according to the DMG profile of the FM-EDFA,enabling DMG equalization.To validate the proposed strategy,DMG equalization of the commonly used FM-EDFA configuration was investigated.Simulation results revealed that by optimizing both the length and RI modulation depth of the femtosecond laser-tailoring area,the maximum DMG(DMGmax)among the 3 linear-polarized(LP)mode-group was mitigated from 10 dB to 1.52 dB,whereas the average DMG(DMGave)over the C-band was reduced from 8.95 dB to 0.78 dB.Finally,a 2-LP mode-group DMG equalizer was experimentally demonstrated,resulting in a reduction of the DMGmax from 2.09 dB to 0.46 dB,and a reduction of DMGave over the C band from 1.64 dB to 0.26 dB,with only a 1.8 dB insertion loss.Moreover,a maximum range of variable DMG equalization was achieved with 5.4 dB,satisfying the requirements of the most commonly used 2-LP mode-group amplification scenarios.

Logarithmic Gain-carrier Density Characteristic of QW Lasers

The relationship between gain and carrier density is analysed. In the quantum well (QW) lasers, initially, the gain increases rapidly with the carrier density and then starts to saturate. It can be seen that QW lasers have a higher differential gain because of the step-like state density, and that the gain saturates at higher carrier densities because of the constant state density of the lowest subband. It is shown that simple logarithmic gain-carrier density is more accurate than the traditional linearized form for a QW laser.

Mode-dependent dynamic gain of all-fiber FM-EDFA under various pump manipulation

The dynamic gain of a few-mode erbium-doped fiber amplifier(FM-EDFA)is vital for the long-haul mode division multiplexing(MDM)transmission.Here,we investigate the mode-dependent dynamic gain of an FM-EDFA under various manipulations of the pump mode.First,we numerically calculate the gain variation with respect to the input signal power,where a modedependent saturation input power occurs under different pump modes.Even under the fixed intensity profile of the pump laser,the saturation input power of each spatial mode is different.Moreover,high-order mode pumping leads to a compression of the linear amplification region,even though it is beneficial for the mitigation of the differential modal gain(DMG)arising in all guided modes.Then,we develop an all-fiber 3-mode EDFA,where the fundamental mode of the pump laser can be efficiently converted to the LP_(11)mode using the all-fiber mode-selective coupler(MSC).In comparison with the traditional LP_(01)pumping scheme,the DMG at 1550 nm can be mitigated from 1.61 dB to 0.97 dB under the LP_(11)mode pumping,while both an average gain of 19.93 dB and a DMG of less than 1 dB can be achieved from 1530 nm to 1560 nm.However,the corresponding signal input saturation powers are reduced by 0.3 dB for the LP_(01)mode and 1.6 dB for the LP_(11)mode,respectively.Both theoretical and experimental results indicate that a trade-off occurs between the DMG mitigation and the extension of the linear amplification range when the intensity profile of pump laser is manipulated.

Optimization Design of Active Structure of Strained MQW DFB Lasers

The well number and the cavity length of 1.55μm wavelength In 1-x-y Ga y Al x As MQW DFB lasers are optimized using a simple model.A low threshold,maximum operating temperature of 550～560K,and high relaxation oscillation frequency of over 30GHz MQW DFB laser is presented.