Solvent transport dynamics and its effect on evolution of mechanical properties of nitrocellulose(NC)-based propellants under hot-air drying process

Appropriate drying process with optimized controlling of drying parameters plays a vital role in the improvement of the quality and performance of propellant products.However,few research on solvent transport dynamics within NC-based propellants was reported,and its effect on the evolution of mechanical properties was not interpreted yet.This study is conducted to gain a comprehensive understanding of hot-air drying for NC-based propellants and clarify the effect of temperature on solvent transport behavior and further the change of mechanical properties during drying.The drying kinetic curves show the drying time required is decreased but the steady solvent content is increased and the drying rate is obviously increased with the increase of hot-air temperatures,indicating hot-air temperatures have a significant effect on drying kinetics.A modified drying model was established,and results show it is more appropriate to describe solvent transport behavior within NC-based propellants.Moreover,two linear equations were established to exhibit the relationship between solvent content and its effect on the change of tensile properties,and the decrease of residual solvent content causes an obvious increase of tensile strength and tensile modulus of propellant products,indicating its mechanical properties can be partly improved by adjustment of residual solvent content.The outcomes can be used to clarify solvent transport mechanisms and optimize drying process parameters of double-based gun propellants.

Simulation of the Ecosystem Productivity Responses to Aerosol Diffuse Radiation Fertilization Effects over the Pan-Arctic during 2001–19

The pan-Arctic is confronted with air pollution transported from lower latitudes.Observations have shown that aerosols help increase plant photosynthesis through the diffuse radiation fertilization effects(DRFEs).While such DRFEs have been explored at low to middle latitudes,the aerosol impacts on pan-Arctic ecosystems and the contributions by anthropogenic and natural emission sources remain less quantified.Here,we perform regional simulations at 0.2o×0.2ousing a well-validated vegetation model(Yale Interactive terrestrial Biosphere,YIBs)in combination with multi-source of observations to quantify the impacts of aerosol DRFEs on the net primary productivity(NPP)in the pan-Arctic during 2001-19.Results show that aerosol DRFEs increase pan-Arctic NPP by 2.19 Pg C(12.8%)yr^(-1)under clear-sky conditions,in which natural and anthropogenic sources contribute to 8.9% and 3.9%,respectively.Under all-sky conditions,such DRFEs are largely dampened by cloud to only 0.26 Pg C(1.24%)yr^(-1),with contributions of 0.65% by natural and 0.59% by anthropogenic species.Natural aerosols cause a positive NPP trend of 0.022% yr^(-1)following the increased fire activities in the pan-Arctic.In contrast,anthropogenic aerosols induce a negative trend of-0.01% yr^(-1)due to reduced emissions from the middle latitudes.Such trends in aerosol DRFEs show a turning point in the year of 2007 with more positive NPP trends by natural aerosols but negative NPP trends by anthropogenic aerosols thereafter.Though affected by modeling uncertainties,this study suggests a likely increasing impact of aerosols on terrestrial ecosystems in the pan-Arctic under global warming.

Effect of Size and Initial Water Content on the Effective Diffusion Coefficient during Convective Drying of Sweet Potato Cut into Cubic and Cylindrical Shapes

In this article, we investigated the influence of size and initial water content on the effective diffusion coefficient of sweet potatoes samples cut into cubic and cylindrical shapes. The sizes of the cubic samples are 0.5, 1, 1.5, 1.75, 2, 2.5 and 3 cm edge with a respective initial water content of 2.7, 3.76, 3.48, 2.68, 3.28, 2.17 and 2.29 kg/kgms. For cylindrical samples, the radius is set at 0.5 cm and sample heights are 1, 1.5, 2, 2.5, 3, 3.5 and 4 cm with respective water contents of 2.2, 3.19, 2.85, 2.1, 2.17, 2.39 and 2.03 kg/kgms. The effective diffusion coefficients of cubic samples are of the order of 10−10 and 10−9 m2∙s−1 grew with sample edge. As for the cylindrical samples, the effective diffusion coefficients were of the order of 10−9 m2∙s−1 and there was no linear correlation between cylinder height and their effective diffusion coefficient. As for the examination of the initial water content on the effective diffusion coefficient, it turned out that the initial water content had no influence on the effective diffusion coefficient of the sweet potato samples.

Unveiling the Re,Cr,and I diffusion in saturated compacted bentonite using machine-learning methods

The safety assessment of high-level radioactive waste repositories requires a high predictive accuracy for radionuclide diffusion and a comprehensive understanding of the diffusion mechanism.In this study,a through-diffusion method and six machine-learning methods were employed to investigate the diffusion of ReO_(4)^(−),HCrO_(4)^(−),and I−in saturated compacted bentonite under different salinities and compacted dry densities.The machine-learning models were trained using two datasets.One dataset contained six input features and 293 instances obtained from the diffusion database system of the Japan Atomic Energy Agency(JAEA-DDB)and 15 publications.The other dataset,comprising 15,000 pseudo-instances,was produced using a multi-porosity model and contained eight input features.The results indicate that the former dataset yielded a higher predictive accuracy than the latter.Light gradient-boosting exhibited a higher prediction accuracy(R2=0.92)and lower error(MSE=0.01)than the other machine-learning algorithms.In addition,Shapley Additive Explanations,Feature Importance,and Partial Dependence Plot analysis results indicate that the rock capacity factor and compacted dry density had the two most significant effects on predicting the effective diffusion coefficient,thereby offering valuable insights.

M-T Scheme for Predicting Effective Diffusion Coefficient of Chloride Ions in Cement-based Materials

To investigate the transport characteristics of chloride ions in cement-based materials, the Mori-Tanaka (M-T) prediction scheme of the effective diffusion coefficient in composites containing single-phase and multi-phase inclusions is systematically deduced based on the theory of composite mechanics and porous medium. The volume fraction, morphology and distribution of aggregates, as well as the interfacial transition zone (ITZ) are fully taken into consideration in this proposed model. The results show that the algorithm of M-T prediction scheme with high accuracy is relatively simple.

Fractal scaling of effective diffusion coefficient of solute in porous media

Fractal approach is used to derive a power law relation between effective diffusion coefficient of solute in porous media and the geometry parameter characterizing the media. The results are consistent with the empirical equations analogous to Archie`s law and are expected to be applied to prediction of effective diffusion coefficient. Key words: diffusion; effective diffusion coefficient; fractal; porous media.

Temporal Spreading Effect of Oceanic Lidar System

In this paper, multipath temporal spreading distributions of laser pulses are calculated when they travel through the seawater. Individual photon is followed in Monte Carlo calculation A modified Henyey-Greenstein （HG） function is applied to represent the scattering phase function of seawater. This paper proposes a new scaling method, which uses the effective scattering thickness τd to replace the optical thickness used in the traditional scaling technique. This paper compares the temporal spreading distributions of photons on conditions of different attenuation coefficients and target depths. The experiments reveal that these mutual deviations are changing in the range from 0.5% to 5%, so long as the corresponding effective scattering thicknesses τd remains the same. Therefore, a conclusion can be obtained, that the temporal spreading distribution is only dependent on the effective diffusion thickness τd .

Generation and manipulation of bright spatial bound-soliton pairs under the diffusion effect in photovoltaic photorefractive crystals

The generation and propagation characteristics of bright spatial bound-soliton pairs (BSPs) are investigated under the diffusion effect in photovoltaic photorefractive crystals by numerical simulation. The results show that two coherent solitons, one as the signal light and the other as the control light, can form a BSP when the peak intensity of the control light is appropriately selected. Moreover, under the diffusion effect, the BSP experiences a self-bending process during propagating and the center of the BSP moves on a parabolic trajectory. Furthermore, the lateral shift of the BSP at the output face of the crystal can be manipulated by adjusting the peak intensity of the control light. The research results provide a method for the design of all-optical switching and routing based on the manipulation of the lateral position of BSPs.

EFFECTIVE DIFFUSION AND EFFECTIVE DRAG COEFFICIENT OF A BROWNIAN PARTICLE IN A PERIODIC POTENTIAL

We study the stochastic motion of a Brownian particle driven by a constant force over a static periodic potential. We show that both the effective diffusion and the effective drag coefficient are mathematically well-defined and we derive analytic expressions for these two quantities. We then investigate the asymptotic behaviors of the effective diffusion and the effective drag coefficient, respectively, for small driving force and for large driving force. In the case of small driving force, the effective diffusion is reduced from its Brownian value by a factor that increases exponentially with the amplitude of the potential. The effective drag coefficient is increased by approximately the same factor. As a result, the Einstein relation between the diffusion coefficient and the drag coefficient is approximately valid when the driving force is small. For moderately large driving force, both the effective diffusion and the effective drag coefficient are increased from their Brownian values, and the Einstein relation breaks down. In the limit of very large driving force, both the effective diffusion and the effective drag coefficient converge to their Brownian values and the Einstein relation is once again valid.

The Approximate Analytical Solution of Non-Linear Equation for Simultaneous Internal Mass and Heat Diffusion Effects

For the first time a mathematical modelling of porous catalyst particles subject to both internal mass concentration gradients as well as temperature gradients, in endothermic or exothermic reactions has been reported. This model contains a non-linear mass balance equation which is related to rate expression. This paper presents an approximate analytical method (Modified Adomian decomposition method) to solve the non-linear differential equations for chemical kinetics with diffusion effects. A simple and closed form of expressions pertaining to substrate concentration and utilization factor is presented for all value of diffusion parameters. These analytical results are compared with numerical results and found to be in good agreement.

Effects of Positron Diffusion and Its Application in Composite System

The effects of positron diffusion on the measured S parameter have been investigated by a point-source diffusion model and a δ function method. Firstly, the theoretical analyses of the effects are presented for the samples of a homogeneous semi-infinite medium and a film of definite thickness. Then the results are used to analyze the S parameters in several composite systems and interface models.

Effect of Back Diffusion of Mg Dopants on Optoelectronic Properties of InGaN-Based Green Light-Emitting Diodes

The effect of back-diffusion of Mg dopants on optoelectronic characteristics of InGaN-based green light-emitting diodes （LEDs） is investigated. The LEDs with less Mg back-diffusion show blue shifts of longer wavelengths and larger wavelengths with the increasing current, which results from the Mg-dopant-related polarization screening. The LEDs show enhanced efficiency with the decreasing Mg back-diffusion in the lower current region. Light outputs follow the power law L α I^m, with smaller parameter m in the LEDs with less Mg back-diffusion, indicating a lower density of trap states. The trap-assisted tunneling current is also suppressed by reducing Mg- defect-related nonradiative centers in the active region. Furthermore, the forward current-voltage characteristics are improved.

Effect of Electric Current on Diffusion of Aluminum in Ti3AlC2 into Zirconium Alloy

The spark plasma sintering（SPS） method was used to study the mechanism of reaction interface between Zr and Ti3AlC2 with electric current going through it. It was found that electric current greatly reduced the bonding temperature of Zr and Ti3AlC2. By the micro-structure analysis of the interface through SEM/EDS, it was found that Al atoms diffused from the Ti3AlC2 substrate into the Zr side and reacted with Zr to form the Zr-Al compounds at the interface, which is the strengthening mechanism of Ti3AlC2-Zr bonding. The thickness of reaction layers（Zr-Al alloy） was from 0.879 to 13.945 mm depending on different sintering condition. Current direction, heating rate, soaking time, pulse patterns all influenced the diffusion of Al atoms which affected the joining quality of Zr and Ti3AlC2.

Effect of Ocean Thermal Diffusivity on Global Warming Induced by Increasing Atmospheric CO_2

A global mean ocean model including atmospheric heating, heat capacity of the mixed layer ocean, and vertical thermal diffusivity in the lower ocean, proposed by Cess and Goldenberg (1981), is used in this paper to study the sensitivity of global warming to the vertical diffusivity. The results suggest that the behaviour of upper ocean temperature is mainly determined by the magnitude of upper layer diffusivity and an ocean with a larger diffusivity leads to a less increase of sea surface temperature and a longer time delay for the global warming induced by increasing CO2 than that with smaller one. The global warming relative to four scenarios of CO2 emission assumed by Intergovernmental Panel of Climate Change (IPCC) is also estimated by using the model with two kinds of thermal diffusivities. The result shows that for various combinations of the CO2 emission scenarios and the diffusivities, the oceanic time delay to the global warming varies from 15 years to 70 years.

Effects of Distribution of Induced Defects on Positron Diffusion

The effects of distribution of induced defects on the positron diffusion was studied by using the point-source diffusion model and 6 function method.

Mesoporous molybdenum carbide for greatly enhanced hydrogen evolution at high current density and its mechanism studies

Currently the catalysis of hydrogen evolution reaction(HER)is mainly focused on the inherent electrocatalytic activity at relatively lower current densities while scarce at high current densities.Nevertheless,the latter is highly demanding in efficient mass-production of hydrogen.A SiO_(2) nanospheres template-synthesis is used to prepare mesoporous molybdenum carbide nanocrystals-embedded nitrogen-doped carbon foams(mp-Mo_(2)C/NC).The material shows much more excellent catalytic activity than the non-etched Mo_(2)C/NC toward hydrogen evolution reaction(HER)in acidic medium.More interestingly mp-Mo_(2)C/NC still has larger overpotential than Pt/C at lower current densities,but possess remarkably smaller overpotential than the latter at higher current densities for much better electrocatalytic performance.An approach is developed to investigate the electrode kinetics by Tafel plots,especially with eliminating the diffusion effect,indicating that Pt/C and mp-Mo_(2)C/NC display different reaction mechanisms.At low current densities the former presents reversible reaction,while the latter shows mixed electrochemical polarization/reversible electrode process.In the region of higher current densities,the former becomes totally gas-diffusion controlled with large overpotential,while the latter can still retain an electrode polarization process for much lower overpotential at the same current density.Result endorses that the meso-porously structured mp-Mo_(2)C/NC plays a critical role in avoiding gas diffusion control-resulting large overpotential at high current densities.This work holds great potential for an inexpensive catalyst better than Pt/C in practical applications of mass-production hydrogen at high current densities,while clearly shedding fundamental lights on designs of rational HER catalysts for the uses at high current densities.

Diffusion Characteristics of Swells in the North Indian Ocean

Research on the diffusion characteristics of swells contributes positively to wave energy forecasting, swell monitoring, and early warning. In this work, the South Indian Ocean westerly index(SIWI) and Indian Ocean swell diffusion effect index(IOSDEI) are defined on the basis of the 45-year(September 1957–August 2002) ERA-40 wave reanalysis data from the European Centre for Medium-Range Weather Forecasts(ECMWF) to analyze the impact of the South Indian Ocean westerlies on the propagation of swell acreage. The following results were obtained: 1) The South Indian Ocean swell mainly propagates from southwest to northeast. The swell also spreads to the Arabian Sea upon reaching low-latitude waters. The 2.0-meter contour of the swell can reach northward to Sri Lankan waters. 2) The size of the IOSDEI is determined by the SIWI strength. The IOSDEI requires approximately 2–3.5 days to fully respond to the SIWI. The correlations between SIWI and IOSDEI show obvious seasonal differences, with the highest correlations found in December–January–February(DJF) and the lowest correlations observed in June–July–August(JJA). 3) The SIWI and IOSDEI have a common period of approximately 1 week in JJA and DJF. The SIWI leads by approximately 2–3 days in this common period.

Numerical simulation to evaluate gas diffusion of turbulent flow in mine ventilation system

Tracer gas technique is a method to analyze the airflow path, measure the airflow quantity, and detect any recirculation or leakages in underground mine. In addition, it is also possible to evaluate the axial gas diffusion of gas in turbulent bulk flow by utilizing the tracer gas data. This paper discussed about the measurement using tracer gas technique in Cibaliung Underground Mine, Indonesia and the evaluation of effective axial diffusion coefficient, E, by numerical simulation. In addition, a scheme to treat network flow in mine ventilation system was also proposed. The effective axial diffusion coefficient for each airway was evaluated based on Taylor's theoretical equation. It is found that the evaluated diffusion coefficient agrees well with Taylor's equation by considering that the wall friction factor, f, is higher than those for smooth pipe flow. It also shows that the value of effective diffusion coefficient can be inherently determined and the value is constant when matching with other measurements. Furthermore, there are possibilities to utilize the tracer gas measurement data to evaluate the airway friction factors.

Determination of Mass Transfer Parameters During Deep Fat Frying of Rice Crackers

The accuracy of the knowledge of mass transfer parameters （effective moisture diffusivity, mass transfer Biot number and mass transfer coefficient） in the case of frying food, is essential and important for designing, modeling and process optimization. This study is undertaken to develop an approach for determining mass transfer parameters during frying of spherical rice cracker in sunflower oil at 150, 170 and 190 ℃. These parameters were evaluated from the plots of dimensionless concentration ratios against time of frying. Effective moisture diffusivity, mass transfer Biot number and mass transfer coefficient ranged between 1.24×10^-8 to 2.36×10^-8 m^2/s, 1.96 to 2.34 and 5.51×10^-6 to 9.70×10^-6 m/s, respectively. Effective moisture diffusivity and mass transfer coefficient were found to increase with an increasing frying temperature, whereas mass transfer Biot number decreased. An Arrhenius-type relationship was found between effective diffusivity coefficient and frying temperature.

Electromagnetohydrodynamic flows and mass transport in curved rectangular microchannels

Curved microchannels are often encountered in lab-on-chip systems because the effective axial channel lengths of such channels are often larger than those of straight microchannels for a given per unit chip length.In this paper,the effective diffusivity of a neutral solute in an oscillating electromagnetohydrodynamic(EMHD)flow through a curved rectangular microchannel is investigated theoretically.The flow is assumed as a creeping flow due to the extremely low Reynolds number in such microflow systems.Through the theoretical analysis,we find that the effective diffusivity primarily depends on five dimensionless parameters,i.e.,the curvature ratio of the curved channel,the Schmidt number,the tidal displacement,the angular Reynolds number,and the dimensionless electric field strength parameter.Based on the obtained results,we can precisely control the mass transfer characteristics of the EMHD flow in a curved rectangular microchannel by appropriately altering the corresponding parameter values.