A two stage turbocharging control system was proposed,in which the pressure regulator valve with a close-loop pressure adjusting function instead of a high speed on-off solenoid valve,is used as a driving mechanism of...A two stage turbocharging control system was proposed,in which the pressure regulator valve with a close-loop pressure adjusting function instead of a high speed on-off solenoid valve,is used as a driving mechanism of waste gate.A digital-analog(DA)conversion circuit based on pulse width modulation(PWM)generates one analog voltage signal required by the pressure regulating valve control.The principle of the DA conversion circuit was analyzed,meanwhile,the performance of the conversion circuit was improved by adopting a speed-up capacitor,which helps to increase the stability and responsiveness of the control voltage generated by the conversion circuit;the structure parameters of the circuit was optimized by simulation.After the optimization,the ripple wave of circuit output voltage was kept within16mV under the 12bit conversion accuracy,the conversion time of the circuit could be reduced to 4ms.The engine bench test show that the turbocharging boost pressure control system which adopted the circuit had a rather good stable control accuracy(the steady state within 0.8%)and dynamic response(the regulation time is less than 4s).展开更多
Objective BEPCII is a high-performance collider with a design energy of 2.1 GeV. In order to obtain more physical experimentsand synchrotron radiation applications, BEPCII decided to carry out energy upgrading to 2.5 ...Objective BEPCII is a high-performance collider with a design energy of 2.1 GeV. In order to obtain more physical experimentsand synchrotron radiation applications, BEPCII decided to carry out energy upgrading to 2.5 GeV. Insufficient energyof special magnet power supplies in collision zone is a key factor restricting BEPCII’s operation under 2.5 GeV energy.Therefore, three high-power and high-stability power supplies are designed for BEPCII energy upgrading.Methods The designed power supplies output part adopts high-frequency chopper modules parallel connected and adoptsdigital-analog hybrid control methods. The voltage loop regulator uses high-speed analog control, and current loop regulatoruses digital control which is based on FPGA.Conclusion The experimental data show that the output current stability of the developed power supplies is lower than50 ppm. The output current resolution is lower than 70 ppm. The developed power supplies can well meet the design requirementsof BEPCII energy upgrading.展开更多
基金Supported by the Ministerial Level Research Project of China(D2220112901)
文摘A two stage turbocharging control system was proposed,in which the pressure regulator valve with a close-loop pressure adjusting function instead of a high speed on-off solenoid valve,is used as a driving mechanism of waste gate.A digital-analog(DA)conversion circuit based on pulse width modulation(PWM)generates one analog voltage signal required by the pressure regulating valve control.The principle of the DA conversion circuit was analyzed,meanwhile,the performance of the conversion circuit was improved by adopting a speed-up capacitor,which helps to increase the stability and responsiveness of the control voltage generated by the conversion circuit;the structure parameters of the circuit was optimized by simulation.After the optimization,the ripple wave of circuit output voltage was kept within16mV under the 12bit conversion accuracy,the conversion time of the circuit could be reduced to 4ms.The engine bench test show that the turbocharging boost pressure control system which adopted the circuit had a rather good stable control accuracy(the steady state within 0.8%)and dynamic response(the regulation time is less than 4s).
文摘Objective BEPCII is a high-performance collider with a design energy of 2.1 GeV. In order to obtain more physical experimentsand synchrotron radiation applications, BEPCII decided to carry out energy upgrading to 2.5 GeV. Insufficient energyof special magnet power supplies in collision zone is a key factor restricting BEPCII’s operation under 2.5 GeV energy.Therefore, three high-power and high-stability power supplies are designed for BEPCII energy upgrading.Methods The designed power supplies output part adopts high-frequency chopper modules parallel connected and adoptsdigital-analog hybrid control methods. The voltage loop regulator uses high-speed analog control, and current loop regulatoruses digital control which is based on FPGA.Conclusion The experimental data show that the output current stability of the developed power supplies is lower than50 ppm. The output current resolution is lower than 70 ppm. The developed power supplies can well meet the design requirementsof BEPCII energy upgrading.