Development of 400-μW cryogen-free dilution refrigerators for quantum experiments

We have successfully developed cryogen-free dilution refrigerators with medium cooling power that can be applied to quantum experiments. Breakthroughs have been made in some key technologies and components of heat switches and dilution units. Our prototype has been running continuously and stably for more than 100 hours below 10 m K, with a minimum temperature of 7.6 m K and a cooling power of 450 μW at 100 m K. At the same time, we have also made progress in the application of dilution refrigerators, such as quantum computing, low-temperature detector, and magnet integration. These indicators and test results indicate good prospects for application in physics, astronomy, and quantum information.

Effect of CO_(2) dilution on laminar burning velocities,combustion characteristics and NO_(x) emissions of CH_(4)/air mixtures

The laminar combustion characteristics of CH_(4)/air premixed flames with CO_(2) addition are systemically studied.Experimental measurements and numerical simulations of the laminar burning velocity(LBV)are performed in CH_(4)/CO_(2)/Air flames with various CO_(2) doping ratio under equivalence ratios of 1.0–1.4.GRI 3.0 mech and Aramco mech are employed for predicting LBV,adiabatic flame temperature(AFT),important intermediate radicals(CH_(3),H,OH,O)and NO_(x) emissions(NO,NO_(2),N2O),as well as the sensitivity analysis is also conducted.The detail analysis of experiment and simulation reveals that as the CO_(2) addition increases from 0%to 40%,the LBVs and AFTs decrease monotonously.Under the same CO_(2) doping ratio,the LBVs and AFTs increase first and then decrease with the increase of equivalence ratio,and the maximum of LBV is reached at equivalence ratio of 1.05.The mole fraction tendency of important intermediates and NO_(x) with equivalence ratio and CO_(2) doping ratio are similar to the LBVs and AFTs.Reaction H+O_(2)⇔O+OH is found to be responsible for the promotion of the generation of important intermediates and NO_(x) under the equivalence ratios and CO_(2) addition through sensitivity analysis.The sensitivity coefficients of elementary reactions that the increasing of CO_(2) doping ratio promotes or inhibits formation of intermediate radicals and NO_(x) decreases.

Dilution characteristics of dual buoyant jets in wavy cross-flow environment

Due to the difference in density between the discharge effluent and coastal water,partially treated wastewater is often discharged into the marine environment as a buoyant jet via submarine outfalls with multiport diffusers.The dilution characteristics of effluent discharge(dual buoyant jets)in a wavy cross-flow environment were studied in a laboratory.The planar laser-induced fluorescence technique was used to obtain the concentration data of the jets.The effects of different environmental variables on the diffusion and dilution characteristics of the jets were examined through physical experiments,dimensional analysis,and empirical formulations.It was found that the dilution process of the dual jets could be divided into two components:the original jet component and the effluent cloud component.The jet-to-current velocity ratio was the main parameter affecting the concentration levels of the effluent cloud.The merging of the two jets increased the jet concentration in the flow field.When the jets traveled further downstream,the axial dilution increased gradually and then increased significantly along the axis.Under the effects of strong waves,the concentration contours branched into two peaks,and the mean dilution became more significant than under the effects of weak waves.Therefore,the dilution of the effluent discharge was expected to be significant under strong wave effects because the hydrodynamic force increased.A dilution equation was derived to improve our understanding of the dilution process of buoyant jets in a wavy cross-flow environment.This equation was used to determine the influences of the jet-to-current velocity ratio,wave-to-current velocity ratio,and Strouhal number on the minimum jet dilution.It revealed that the wave and buoyancy effects in effluent discharges were significant.

Synthesis and Flocculation of Polyacrylamide with Low Water Absorption for Non-dispersible Underwater Concrete

The polyacrylamide which is directly added into concrete shows strong water absorption property.Thus the construction of underwater constructure would demand high amount of water,resulting in poor workability of concrete and strength shrinkage after hardening.Herein,a kind of anionic polyacrylamide(APAM)grafted with water reducing functional group(-COOH)was synthesized at low temperatures by partial factor design and response surface design.The structure and morphology of APAM were characterized by UV,FTIR and SEM methods.The experimental results show that the molecular weight of the synthesized APAM could reach 11 million,under the condition that the temperature was 35℃,the pH value was 8,the monomer concentration was 27wt%,the initiator dosage was 0.6wt%,and the monomer ratio(n(AM):n(AA))was 3.When the APAM was applied into the underwater slurry,it presented good flocculation and low water demand.When the dosage was 1%of the mass of the cement,the water demand increased by 12%,which could meet the self-leveling and anti-dispersity of the underwater slurry at the same time.This technology provides technical guidance for the large-scale industrial production of polyacrylamide for underwater concrete construction while achieving environmental protection during production.

What Is the Difference between Post- and Pre-Dilution in On-Line Haemodiafiltration in the Removing of Median-Molecular-Weight Toxins?

Introduction: β2-microglobulin and prolactin are medium-molecular-weight toxins. We believe that the rate of removal of these molecules, using filters with two different surfaces, in post- and pre-dilution haemodiafiltration, will be of interest to the literature. Methods: We studied, in 12 haemodialyzed patients, the removal of those, with filter with surface of 2.5 m2 (Group A) or 2.1 m2 (Group B) with post-dilution haemodiafiltration, and with a filter with surface 2.5 m2 with pre-dilution (Group C). Results: Satisfactory removal of β2-microglobulin (best with post-dilution) was found, and a good rate of removal of prolactin without the filter surface played a role in both cases. Conclusion: The elimination of β2-microglobulin in post-dilution is not affected by the filter surface area. Pre-dilution achieves removal of β2-microglobulin, less than that of post-dilution. Prolactin was removed satisfactorily regardless of the filter surface in post-dilution, and its removal appears to be less than that of β2-microglobulin.

Regulating the dopant clustering in LiZnAs-based diluted magnetic semiconductor

Tuning of the magnetic interaction plays the vital role in reducing the clustering of magnetic dopant in diluted magnetic semiconductors(DMS).Due to the not well understood magnetic mechanism and the interplay between different magnetic mechanisms,no efficient and universal tuning strategy is proposed at present.Here,the magnetic interactions and formation energies of isovalent-doped(Mn) and aliovalent(Cr)-doped LiZnAs are studied based on density functional theory(DFT).It is found that the dopant–dopant distance-dependent magnetic interaction is highly sensitive to the carrier concentration and carrier type and can only be explained by the interplay between two magnetic mechanisms,i.e.,superexchange and Zener’s p–d exchange model.Thus,the magnetic behavior and clustering of magnetic dopant can be tuned by the interplay between two magnetic mechanisms.The insensitivity of the tuning effect to U parameter suggests that our strategy could be universal to other DMS.

Correlation of work function and stacking fault energy through Kelvin probe force microscopy and nanohardness in diluteα-magnesium

Electronic interactions of the Group 2A elements with magnesium have been studied through the dilute solid solutions in binary Mg-Ca,Mg-Sr and Mg-Ba systems.This investigation incorporated the difference in the‘Work Function'(ΔWF)measured via Kelvin Probe Force Microscopy(KPFM),as a property directly affected by interatomic bond types,i.e.the electronic structure,nanoindentation measurements,and Stacking Fault Energy values reported in the literature.It was shown that the nano-hardness of the solid-solutionα-Mg phase changed in the order of Mg-Ca>Mg-Sr>Mg-Ba.Thus,it was shown,by also considering the nano-hardness levels,that SFE of a solid-solution is closely correlated with its‘Work Function'level.Nano-hardness measurements on the eutectics andΔWF difference between eutectic phases enabled an assessment of the relative bond strength and the pertinent electronic structures of the eutectics in the three alloys.Correlation withΔWF and at least qualitative verification of those computed SFE values with some experimental measurement techniques were considered important as those computational methods are based on zero Kelvin degree,relatively simple atomic models and a number of assumptions.As asserted by this investigation,if the results of measurement techniques can be qualitatively correlated with those of the computational methods,it can be possible to evaluate the electronic structures in alloys,starting from binary systems,going to ternary and then multi-elemental systems.Our investigation has shown that such a qualitative correlation is possible.After all,the SFE values are not treated as absolute values but rather become essential in comparative investigations when assessing the influences of alloying elements at a fundamental level,that is,free electron density distributions.Our study indicated that the principles of‘electronic metallurgy'in developing multi-elemental alloy systems can be followed via practical experimental methods,i.e.ΔWF measurements using KPFM and nanoindentation.

First-Principle Study on the Electronic Structure and Optical Property of New Diluted Magnetic Semiconductor(Y_(0.75)Ca_(0.25))(Cu_(0.75)Mn_(0.25))SO

The band structure,DOSs,and optical properties of(Y_(0.75)Ca_(0.25))(Cu_(0.75)Mn_(0.25))SO,including dielectric function,absorption function,reflection function,and energy loss spectrum were studied by using the first-principles calculation.The calculation results indicate that(Y_(0.75)Ca_(0.25))(Cu_(0.75)Mn_(0.25))SO is a direct bandgap semiconductor with a bandgap of 1.1 eV.The Fermi surface is asymmetric and exhibits spin splitting phenomenon.The new type of dilute magnetic semiconductor(Y_(0.75)Ca_(0.25))(Cu_(0.75)Mn_(0.25))SO exhibits significant light loss around 70 eV,with light reflection gradually increasing after 30 eV,and light absorption mainly occurring around 8-30 eV.These results also provide a basis for the discovery of more types of 1111 phase new dilute magnetic semiconductors in the future.

Shear hydrophobic flocculation and flotation of ultrafine Anshan hematite using sodium oleate

Effects of stirring speed and time, pH and sodium oleate concentration on the shear hydrophobic flocculation of ultrafine Anshan hematite with sodium oleate as the surfactant were discussed. The results show that these parameters significantly affect the shear hydrophobic flocculation of ultrafine hematite. The optimum conditions for the flocculation are： stirring speed 1 400 r/min, flocculation time 20 min, pH 9 and sodium oleate concentration 3.94×10-4 mol/L; the flotation recovery of hematite flocs is remarkably high compared with non flocculated ultrafine hematite. According to the extended DLVO theory, the total interaction potential of Anshan ultrafine hematite was determined. The calculation results indicate that the hydrophobic flocculation state of the ultrafine hematite-sodium oleate system is mainly dominated by electric double layer repulsive interaction potential and hydrophobic interaction potential. A mechanical agitation is required to impart particles a kinetic energy to overcome potential barrier between them due to the existence of electric double layer repulsive interaction potential. Those particles further approach to form flocs due to the significant increase of the hydrophobic interaction potential.

Screening of a Novel Bioflocculant-producing Strain and Research on Its Flocculation

[Objective] This study aimed to screen a bacterial strain capable of producing bioflocculant. [Method] A bacterial strain T-11 capable of producing bioflocculant was isolated from activated sludge. Detailed tests on the morphological, physiological and biochemical characteristics were carried out and identification was performed to identify the strain. Finally, the bioflocculant was isolated and purified, and the flocculating activity and chemical characteristics were measured. [Result] It was identified as Serratia plumuthica based on its morphological, physiological and biochemical characteristics. This strain secreted flocculant best in a culture medium which included sucrose and NaNO3. The maximal cell growth was achieved within 10 h and the flocculating activity paralleled to it. It was found to be effective for flocculation of kaolin suspension, when added at a final concentration of 0.7 mg/L, over a range of pHs （2-7）, and temperature （approximately 30-80 ℃）. Chemical analysis indicated that the bioflocculant was an acidic polysaccharide consisting of glucose, glucuronic acid and galactose, talose and altrose. Infrared spectrum analysis also revealed typical characteristics of polysaccharides. [Conclusion] The biofloccu- lants produced by strain T-11 can greatly improve the ability of activated sludge to settle.

Dynamic experiments on flocculation and sedimentation of argillized ultrafine tailings using fly-ash-based magnetic coagulant

In order to accelerate the sedimentation of super-large-scale argillized ultrafine tailings with bad features such as low settling velocity, muddy overflow water, and large flocculant dosage, a fly-ash-based magnetic coagulant （FAMC） was used in a dynamic experimental device. To obtain the best possible combination of the impact factors （magnetic intensity, FAMC dosage, flocculant dosage, and feed speed） for minimum overflow turbidity, a response surface methodology test coupled with a four-factor five-level central composite design was conducted. The synergy mechanism of FAMC and flocculant was analyzed based on the potential measurement and scanning electron microscopy. The results show that the flocculant dosage, overflow turbidity, and solid content can be reduced by 50%, 90%, and 80%, while the handling capacity per unit and efficiency of backfill and dry stacking can be promoted by 20%, 17%, and 13%, respectively, with a magnetic intensity of 0.3 T, FAMC dosage of 200 mL/t, flocculant dosage of 30 g/t, and feed speed of 0.6 t/（m^2·h）. Therefore, synergy of FAMC and flocculant has obvious efficiency in saving energy and protecting the environment by allowing 70×10^6 t/a of argillized ultrafine tailings slurry to be disposed safely and efficiently with a cost saving of more than 53×106 Yuan/a, which gives it great promise for use in domestic and foreign mines.

Effects of water hardness on selective flocculation of diasporic bauxite

The effect of electrolyte on settling behavior of kaolinite was studied. Effects of hard water on selective flocculation of diasporic bauxite was tested and the measures were taken to eliminate the effects of Ca2＋ and Mg2＋ in hard water. The results indicated that, not only the concentration of electrolyte ions but also the ionic valence of the electrolyte ions affects the settling behavior of kaolinite; hard water significantly affects its selective flocculation owing to Ca2＋ and Mg2＋; general dispersants could not eliminate the effects of Ca2＋ and Mg2＋. Self-made softening agent in our lab could weaken or eliminate the effects of hard water on flocculation processes. The results of molecular dynamics simulation show that softening agent molecules could restrict Ca2＋ and prevent them from playing their roles, so as to eliminate the effects. The continuous pilot experiment results of bauxite flocculation were even better than those obtained in laboratory.

Study on the metastable state of dilution of spectinomycin

采用诱导期法和直接法研究了大观霉素溶析结晶的介稳态.新相形成由多核机理控制.由多核机理得到两个操作温度下溶析结晶的介稳区.实验考察了丙酮浓度和温度对溶析结晶介稳态的影响.随着丙酮浓度的增大或温度的降低,诱导期延长.介稳区宽度随溶解度的减小而变宽.大观霉素初级成核的过饱和度水平较高,属于第Ⅰ类物系.根据经典成核理论估算了大观霉素成核参数.这些实验结果对大观霉素溶析结晶工业生产的控制具有重要意义.

Features and mechanism for coagulation－flocculation processes of polyaluminum chloride

Ｆｅａｔｕｒｅｓａｎｄｍｅｃｈａｎｉｓｍｆｏｒｃｏａｇｕｌａｔｉｏｎ－ｆｌｏｃｃｕｌａｔｉｏｎｐｒｏｃｅｓｓｅｓｏｆｐｏｌｙａｌｕｍｉｎｕｍｃｈｌｏｒｉｄｅＴａｎｇＨｏｎｇｘｉａｏ；ＬｕａｎＺｈａｏｋｕｎ（ＳｔａｔｅＫｅｙＬａｂｏｒａｔｏｒｙｏｆＥｎ...

The effect of coupling coagulation and flocculation with membrane filtration in water treatment:A review

Water supply and sanitation demands are foreseen to face enormous challenges over the coming decades to meet the fast growing needs in a global perspective. Significant growth in the industry is predicted and membrane separation technologies have been identified as one of the possible solutions to meet future demands. Application and implementation of membrane technology is expected both in production of potable water as well as in treatment of wastewater. In potable water production membranes are substituting conventional separation technologies due to the superior performance, potential for less chemical use and sludge production, as well as the potential to fulfill hygienic barrier requirements. Membrane bio-reactor （MBR） technology is probably the membrane process which has had most success and has the best prospects for the future in wastewater treatment. Trends and developments indicate that this technology is becoming accepted and is rapidly becoming the best available technology for many wastewater treatment applications. A major drawback of MBR systems is membrane fouling. Studies have shown that fouling mitigation in MBR systems can potentially be done by coupling coagulation and flocculation to the process.

Synthesis and Flocculation Property of Chitosan-Acrylamide Graft Copolymer

Chitosan, as a kind of natural polymer, has many advantages, such as abundant sources, biological degradation, no secondary contamination and facile modification. In this work, we prepared modified chitosan flocculants with double electrical behavior via polymerizing chitosan, acrylamide and sodium carboxymethyl cellulose together by using ammonium persulfate as the indicator in water. The product is a comb-type of chitosan copolymer and a polymeric ampholyte. And then we studied the product by FTIR, UV-Vis, TG, DSC spectrometeries and viscometry, etc. We also performed CACM′s water treat experiment. The effects of pH values, reaction time and dose of the new floccalant on treating various of waste water have been investigated, too.

Improving the sulfidation-flotation of fine cuprite by hydrophobic flocculation pretreatment

Hydrophobic flocculation pretreatment was performed to assess its effect on the recovery of fine cuprite in sulfidation-flotation. The results of the micro-flotation experiment showed that cuprite recovery is related to the particle size, and that an excessive content of fine particles(<18 μm) impacted the recovery of coarse particles. When hydrophobic flocculation pretreatment was used, the recovery of fine cuprite in sulfidation-flotation increased from 60.3% to 86.3% under optimum conditions(pH 9.5; sodium oleate concentration, 2 × 10^(-4) mol×L^(-1); stirring time, 6 min; stirring speed, 1600 r×min^(-1)). The laser particle size analysis and optical microscopy results indicate that hydrophobic flocculation pretreatment effectively reduces the content of fine cuprite, and augments the apparent particle size in the pulp. We performed the Derjaguin–Landau–Verwey–Overbeek(DLVO) theory and extended DLVO theory calculations to further support the interpretation of the results.

Geometric dilution of precision for GPS single-point positioning based on four satellites

To improve the positioning accuracy in GPS point positioning, the geometric dilution of precision （GDOP） including HDOP, VDOP, TDOP, PDOP is commonly considered. The properties of the DOP for the GPS satellite navigation system are studied and the coordinate system is improved in order to decrease the amount of variables. In the end, by simulation and discussing the results, the corresponding conclusions are presented.

Flocculation performance of a novel synthesized flocculant with low ecological risk

Combined flocculants with low ecological risk are urgently required in water supply and wastewater treatment in China. A novel flocculant was thus developed under the condition of low ecological risk(noted as CAS). The experiments to examine wastewater treatment performance of the new product showed that there was favourable performance in the flocculation process in contrast to commercial flocculants in treating kaolin suspensions, municipal effluent and domestic wastewater. Flocculation performance included the turbidity removal rate, sediment character and a decrease in COD(chemical oxygen demand). The sediment time of flocculation is short and the removal rate of turbidity treated by CAS is high compared with PAC(polyaluminum chloride), PAM(polyacrylamide) and the combined addition of PAC and PAM. The optimal concentration required to affect flocculation processes is dependent on kaolin concentration and the character of the wastewater within the range examined. It also showed that CAS is effective to treat wastewater with high turbidity.

Chemical and biological flocculation process to treat municipal sewage and analysis of biological function

The pilot scale experimental apparatus and the procedure of the chemical and biological flocculation process to verify the feasibility in treating Shanghai municipal sewage were introduced in this paper. In addition, the biological function of the process was discussed. The results of optimal running showed that in the reaction tank, the concentration of mixed liquor suspended solid(MLSS) was 2 g/L, hydraulic retention time(HRT) was 35 min, dosage of liquid polyaluminium chloride(PAC) was 60 mg/L, and the concentration of polyacrylamide(PAM) was 0 5 mg/L. The effluent average concentrations of COD Cr , TP, SS and BOD 5 were 50 mg/L, 0 62 mg/L, 18 mg/L, and 17 mg/L, respectively. These were better than the designed demand. In addition, the existence of biological degradation in this system was proven by several methods. The removal efficiencies of the chemical and biological flocculation process were 20% higher than that of the chemical flocculation process above at the same coagulant dosage. The treatment process under different situations was evaluated on a pilot scale experiment, and the results provided magnificent parameters and optimal condition for future operation of the plant.