Cracks have consistently been a significant challenge limiting the development of additive manufactured nickel-based superalloys.It is essential to investigate the location of cracks and their forming mechanism.This s...Cracks have consistently been a significant challenge limiting the development of additive manufactured nickel-based superalloys.It is essential to investigate the location of cracks and their forming mechanism.This study extensively examines the impact of solidification process,microstructural evolution,and stress concentration on crack initiation during direct energy deposition(DED).The results emphasize that the crack formation is significantly related to large-angle grain boundaries,rapid cooling rates.Cracks caused by large-angle grain boundaries and a fast-cooling rate predominantly appear near the edge of the deposited samples.Liquation cracks are more likely to form near the top of the deposited sample,due to the presence ofγ/γ'eutectics.The secondary dendritic arm and the carbides in the interdendritic regions can obstruct liquid flow during the final stage of solidification,which results in the formation of solidification cracks and voids.This work paves the way to avoid cracks in nickel-based superalloys fabricated by DED,thereby enhancing the performance of superalloys.展开更多
The microstructure characteristics and strengthening mechanism of Inconel738LC(IN-738LC) alloy prepared by using induction-assisted directed energy deposition(IDED) were elucidated through the investigation of samples...The microstructure characteristics and strengthening mechanism of Inconel738LC(IN-738LC) alloy prepared by using induction-assisted directed energy deposition(IDED) were elucidated through the investigation of samples subjected to IDED under 1050℃ preheating with and without hot isostatic pressing(HIP,1190℃,105 MPa,and 3 h).Results show that the as-deposited sample mainly consisted of epitaxial columnar crystals and inhomogeneously distributed γ’ phases in interdendritic and dendritic core regions.After HIP,grain morphology changed negligibly,whereas the size of the γ’ phase became increasingly even.After further heat treatment(HT,1070℃,2 h + 845℃,24 h),the γ’ phase in the as-deposited and HIPed samples presented a bimodal size distribution,whereas that in the as-deposited sample showed a size that remained uneven.The comparison of tensile properties revealed that the tensile strength and uniform elongation of the HIP + HTed sample increased by 5% and 46%,respectively,due to the synergistic deformation of bimodal γ’phases,especially large cubic γ’ phases.Finally,the relationship between phase transformations and plastic deformations in the IDEDed sample was discussed on the basis of generalized stability theory in terms of the trade-off between thermodynamics and kinetics.展开更多
Additive manufacturing provides achievability for the fabrication of bimetallic and multi-material structures;however,the material compatibility and bondability directly affect the parts’formability and final quality...Additive manufacturing provides achievability for the fabrication of bimetallic and multi-material structures;however,the material compatibility and bondability directly affect the parts’formability and final quality.It is essential to understand the underlying printability of different material combinations based on an adapted process.Here,the printability disparities of two common and attractive material combinations(nickel-and iron-based alloys)are evaluated at the macro and micro levels via laser directed energy deposition(DED).The deposition processes were captured using in situ high-speed imaging,and the dissimilarities in melt pool features and track morphology were quantitatively investigated within specific process windows.Moreover,the microstructure diversity of the tracks and blocks processed with varied material pairs was comparatively elaborated and,complemented with the informative multi-physics modeling,the presented non-uniformity in mechanical properties(microhardness)among the heterogeneous material pairs was rationalized.The differences in melt flow induced by the unlike thermophysical properties of the material pairs and the resulting element intermixing and localized re-alloying during solidification dominate the presented dissimilarity in printability among the material combinations.This work provides an in-depth understanding of the phenomenological differences in the deposition of dissimilar materials and aims to guide more reliable DED forming of bimetallic parts.展开更多
Direct energy deposition(DED)has great potential for the production of stainless steel matrix nanocomposite parts.However,the propensity of nanoparticle agglomeration leads to the difficulty in realizing homogenous di...Direct energy deposition(DED)has great potential for the production of stainless steel matrix nanocomposite parts.However,the propensity of nanoparticle agglomeration leads to the difficulty in realizing homogenous dispersion of nanoparticles in the matrix.In this study,a series of agglomeration-free nanoWC-Co-reinforced 420 stainless steel matrix nanocomposite powders with high flowability were prepared by ball milling under the optimal parameters.The effect of ball milling time on the properties of the composite powders was investigated.Excellent powder properties ensure the DED processing performance.Furthermore,the corresponding composites were fabricated by DED,and the effects of nano-WC-Co content on the properties of the composites were comprehensively investigated.The contact angles between the single pass cladding layer and the substrate change with increasing nano-WC-Co content(decrease from 127.38°to 113.07°).The different contact angles will significantly influence the quality of the multipass cladding layer.Furthermore,the addition of nanoWC-Co leads not only to further grain refinement but also to more pronounced isotropy of the micros tructure.With the increase in nano-WC-Co content,the corrosion resistance is significantly improved(62.28%lower corrosion current for 420-15 wt%nano-WC-Co than for 420).展开更多
Lightweight aluminum(Al)alloys have been widely used in frontier fields like aerospace and automotive industries,which attracts great interest in additive manufacturing(AM)to process high-value Al parts.As a mainstrea...Lightweight aluminum(Al)alloys have been widely used in frontier fields like aerospace and automotive industries,which attracts great interest in additive manufacturing(AM)to process high-value Al parts.As a mainstream AM technique,laser-directed energy deposition(LDED)shows good scalability to meet the requirements for large-format component manufacturing and repair.However,LDED Al alloys are highly challenging due to their inherent poor printability(e.g.low laser absorption,high oxidation sensitivity and cracking tendency).To further promote the development of LDED high-performance Al alloys,this review offers a deep understanding of the challenges and strategies to improve printability in LDED Al alloys.The porosity,cracking,distortion,inclusions,element evaporation and resultant inferior mechanical properties(worse than laser powder bed fusion)are the key challenges in LDED Al alloys.Processing parameter optimizations,in-situ alloy design,reinforcing particle addition and field assistance are the efficient approaches to improving the printability and performance of LDED Al alloys.The underlying correlations between processes,alloy innovation,characteristic microstructures,and achievable performances in LDED Al alloys are discussed.The benchmark mechanical properties and primary strengthening mechanism of LDED Al alloys are summarized.This review aims to provide a critical and in-depth evaluation of current progress in LDED Al alloys.Future opportunities and perspectives in LDED high-performance Al alloys are also outlined.展开更多
Ni51Ti49 at.%bulk was additively manufactured by laser-directed energy deposition(DED)to reveal the microstructure evolution,phase distribution,and mechanical properties.It is found that the localized remelting,reheat...Ni51Ti49 at.%bulk was additively manufactured by laser-directed energy deposition(DED)to reveal the microstructure evolution,phase distribution,and mechanical properties.It is found that the localized remelting,reheating,and heat accumulation during DED leads to the spatial heterogeneous distribution of columnar crystal and equiaxed crystal,a gradient distribution of Ni4Ti3 precipitates along the building direction,and preferential formation of Ni4Ti3 precipitates in the columnar zone.The austenite transformation finish temperature(Af)varies from-12.65℃(Z=33 mm)to 60.35℃(Z=10 mm),corresponding to tensile yield strength(σ0.2)changed from 120±30 MPa to 570±20 MPa,and functional properties changed from shape memory effect to superelasticity at room temperature.The sample in the Z=20.4 mm height has the best plasticity of 9.6%and the best recoverable strain of 4.2%.This work provided insights and guidelines for the spatial characterization of DEDed NiTi.展开更多
In recent years,wire-arc directed energy deposition(wa DED),which is also commonly known as wire-arc additive manufacturing(WAAM),has emerged as a promising new fabrication technique for magnesium alloys.The major rea...In recent years,wire-arc directed energy deposition(wa DED),which is also commonly known as wire-arc additive manufacturing(WAAM),has emerged as a promising new fabrication technique for magnesium alloys.The major reason for this is the possibility of producing parts with a complex geometry as well as a fine-grained microstructure.While the process has been shown to be applicable for Mg-Al-Zn alloys,there is still a lack of knowledge in terms of the influence of the WAAM process on the age-hardening response.Consequently,this study deals with the aging response of a WAAM AZ91 alloy.In order to fully understand the mechanisms during aging,first,the as-built condition was analyzed by means of high-energy X-ray diffraction(HEXRD)and scanning electron microscopy.These investigations revealed a finegrained,equiaxed microstructure with adjacent areas of alternating Al content.Subsequently,the difference between single-and double-step aging as well as conventional and direct aging was studied on the as-built WAAM AZ91 alloy for the first time.The aging response during the various heat treatments was monitored via in situ HEXRD experiments.Corroborating electron microscopy and hardness studies were conducted.The results showed that the application of a double-step aging heat treatment at 325℃with pre-aging at 250℃slightly improves the mechanical properties when compared to the single-step heat treatment at 325℃.However,the hardness decreases considerably after the pre-aging step.Thus,aging at lower temperatures is preferable within the investigated temperature range of 250-325℃.Moreover,no significant difference between the conventionally aged and directly aged samples was found.Lastly,the specimens showed enhanced precipitation kinetics during aging as compared to cast samples.This could be attributed to a higher amount of nucleation sites and the particular temperature profile of the solution heat treatment.展开更多
The columnar-to-equiaxed transition(CET)or the formation of stray grains in the laser melting deposition is the least desirable for the repair of single-crystal blades.In this work,the forced water-cooling was conduct...The columnar-to-equiaxed transition(CET)or the formation of stray grains in the laser melting deposition is the least desirable for the repair of single-crystal blades.In this work,the forced water-cooling was conducted on a single-crystal Rene N5 substrate during the direct energy deposition(DED).The single track remelting,one-layer,two-layer,and eight-layer depositions were investigated to explore the grain growth mechanism.The solidification conditions of the DED process,including temperature field,temperature gradient,and solidification speed,were numerically analyzed by a finite element model.The single-track remelting results showed that the fraction of columnar crystal regions increases from55.81%in the air-cooled sample to 77.14%in the water-cooled one.The single-track deposits of one-and two-layer have the same trend,where the proportion of columnar crystal height was higher under the forced water-cooled condition.The electron backscattered diffraction(EBSD)grain-structure maps of an eight-layer deposit show that the epitaxial growth height increases from 1 mm in the air-cooling sample to 1.5 mm in the water-cooling one.The numerical results showed that the tempe rature gradient in[0011 direction was significantly increased by using forced water-cooling.In conclusion,the in-situ substrate cooling can become a potential method to promote epitaxial growth during DED via the influence on CET occurrence.展开更多
An Al-Mg-Sc-Zr alloy was additively manufactured by laser direct energy deposition(DED)under different laser powers,and the microstructures and mechanical properties of the as-deposited samples were investigated.The s...An Al-Mg-Sc-Zr alloy was additively manufactured by laser direct energy deposition(DED)under different laser powers,and the microstructures and mechanical properties of the as-deposited samples were investigated.The samples showed a fully equiaxed grain structure with grain sizes of 2–30μm.Most of the blocky primary Al3(Sc,Zr)-precipitated phases(<5μm)were arranged along the grain boundaries.A small amount of fine granular secondary Al3(Sc,Zr)phases(<0.5μm)were precipitated owing to the cyclic heat treatment during the DED forming process.According to the EBSD(Electron backscatter diffraction)results,the texture index and strength of the sample were only slightly greater than 1,indicating that the material structure exhibited a certain but not obvious anisotropy.The sample in the horizontal direction had better yield strength,tensile strength,and elogation properties(399.87 MPa,220.96 MPa,9.13%)than that in the building direction(385.40 MPa,219.40 MPa,8.24%),although the sample in the〈XOZ〉plane had the finest equiaxed grains.The ductility of the〈XOZ〉sample deteriorated as the number of pores increased.展开更多
NiTi shape memory alloy(SMA)with nominal composition of Ni 50.8 at%and Ti 49.2 at%was additively manufactured(AM)by selective laser melting(SLM)and laser directed energy deposition(DED)for a comparison study,with emph...NiTi shape memory alloy(SMA)with nominal composition of Ni 50.8 at%and Ti 49.2 at%was additively manufactured(AM)by selective laser melting(SLM)and laser directed energy deposition(DED)for a comparison study,with emphasis on its phase composition,microstructure,mechanical property and deformation mechanism.The results show that the yield strength and ductility obtained by SLM are 100 MPa and 8%,respectively,which are remarkably different from DED result with 700 MPa and 2%.The load path of SLM sample presents shape memory effect,corresponding to martensite phase detected by XRD;while the load path of DED presents pseudo-elasticity with austenite phase.In SLM sample,fine grain and hole provide a uniform deformation during tensile test,resulting in a better elongation.Furthermore,the nonequilibrium solidification was studied by a temperature field simulation to understand the difference of the two 3D printing methods.Both temperature gradient G and growth rate R determine the microstructure and phase in the SLM sample and DED sample,which leads to similar grain morphologies because of similar G/R.While higher G×R of SLM leads to a finer grain size in SLM sample,providing enough driving force for martensite transition and subsequently changing texture compared to DED sample.展开更多
The effect of spatial temperature gradient on the microstructural evolution of a 308L stainless steel during the directed energy deposition(DED)process was experimentally investigated.A novel cooling system was design...The effect of spatial temperature gradient on the microstructural evolution of a 308L stainless steel during the directed energy deposition(DED)process was experimentally investigated.A novel cooling system was designed and incorporated to a DED system in order to control the temperature gradient along the deposition direction during solidification.During deposition,the workpiece was placed on a lifting platform,and as the deposition process proceeded,the platform and workpiece were gradually lowered into cooling water so that the temperature gradient along the deposition direction could be controlled and maintained stable during the deposition process.The microstructure characterization results indicated that a deposition strategy with higher G and G/R values(where G is temperature gradient and R is solidification rate)produced finer cellular grains that were better aligned with the deposition direction,while a deposition strategy with lower G and G/R values produced columnar grains with larger primary arm spacing and less aligned with the deposition direction.展开更多
Porosity is a common phenomenon and can significantly hinder the quality of the coating.Here,the pore formation mechanism and the characteristics of the single tracks of the W-C coating using directed energy depositio...Porosity is a common phenomenon and can significantly hinder the quality of the coating.Here,the pore formation mechanism and the characteristics of the single tracks of the W-C coating using directed energy deposition(DED)are systematically investigated.The forming quality of the tracks,the distribution of the pores,and the elemental distribution near the pores are analyzed by the observations of the cross-sections of the tracks.The temperature field of the melt pool is discussed comprehensively to reveal the pore formation mechanism.The results confirm that Ni and Co evaporated during the DED process due to the high temperature of the melt pool.Pores were continuously produced adjacent to the fusion line when the melt pool was about to solidify since the temperature at the solidification front was higher than the boiling point of Ni.The vaporization area at the fusion line was proposed,where Ni could also evaporate at the time the melt pool started to solidify.The relationship between the solidification rate,the size of the vaporization area and the DED parameters(laser power and scanning speed)was established to discuss the causes of severe pores above the fusion line.This work contains a practical guide to reduce or eliminate the porosity in the coating preparation process on the surface of the tungsten alloy.展开更多
Meeting the damage tolerance requirements for engineering-grade titanium alloys pose a significant challenge in achieving high fracture toughness in direct energy deposition(DED)titanium alloys.This work primarily inv...Meeting the damage tolerance requirements for engineering-grade titanium alloys pose a significant challenge in achieving high fracture toughness in direct energy deposition(DED)titanium alloys.This work primarily investigated the relationship between the microstructure and the fracture toughness of DED new Ti-6Al-4V-1Mo alloy.Two types of microstructures were designed via two process strategies:high-line energy density(HE)and low-line energy density(LE).Relative to LE samples,HE samples possess larger-sized microstructural characteristics(coarser grain boundaryα(α_(GB)),largerαcolonies,and coarserαlaths).Lessα/βphase boundaries were formed by coarserαlaths in the HE samples,increasing the movement of dislocations,resulting in tensile strength decreasing from 1007.1 MPa(LE)to 930.8 MPa(HE)and elongation increasing from 10.8%(LE)to 15.7%(HE).Also,HE samples exhibited an excellent fracture toughness of 114.0 MPa m^(1/2),significantly higher than that of LE samples(76.8 MPa m^(1/2)).An analysis of crack propagation paths was conducted to investigate the factors contributing to toughening.The primary factor enhancing toughness is the frequent obstruction of cracks by coarseαGB and largeαcolonies in HE samples.Particularly,the pretty large-angle deflections induced by the superposition effect of coarseαGB and largeαcolonies play a vital of significant role.These factors induced the long and tortuous high-energy pathways,which resulted in ultimately improved fracture toughness.The discovered microstructural toughening mechanisms can serve as a reference for future studies involving titanium alloys,offering insights on how to enhance fracture toughness by achieving similar characteristics.展开更多
The application of titanium alloys in aerospace put forward the requirement for higher strength.Additive manu-facturing is a promising method for the efficient and economical processing of titanium alloys.However,rese...The application of titanium alloys in aerospace put forward the requirement for higher strength.Additive manu-facturing is a promising method for the efficient and economical processing of titanium alloys.However,research on the additive manufacturing of ultrahigh-strength titanium alloys is still limited.The mechanisms of microseg-regation for high alloying elements and poor plasticity are still not clear.In this study,an ultrahigh-strength titanium alloy Ti-4.5Al-5Mo-5V-6Cr-1Nb(TB18)was prepared using two methods:laser direct energy deposi-tion(LDED)and forging.The LDEDed alloy contains three zones with similar grain morphologies but different microstructure.The microsegregation of the alloy is limited due to the rapid solidification and almost eliminated after the thermal cycle and solution treatment.With stress relief treatment,the LDEDed alloy exhibits anisotropic mechanical properties.After solution and aging treatments,its ultimate strength is enhanced;however,its plas-ticity is relatively lower than that of the wrought alloy with equally high strength.The excellent balance of the strength and plasticity of the wrought alloy can be ascribed to the formation of𝛼WGB and multiscale𝛼laths,which provides enlightenment for optimizing the properties of the LDEDed alloy.展开更多
Inconel 718 is a nickel-based superalloy of high interest in high temperature applications such as turbine parts.To be used in such applications,heat treatments are commonly applied to dissolute Laves phase and to ach...Inconel 718 is a nickel-based superalloy of high interest in high temperature applications such as turbine parts.To be used in such applications,heat treatments are commonly applied to dissolute Laves phase and to achieve𝛾γ′phase.However,conventional heat treatment methods for wrought Inconel 718 may not be suitable for Inconel 718 fabricated by laser directed energy deposition(LDED)due to its unique microstructure formed during the rapid solidification process.There has been a lack of investigation in heat treatments for Inconel 718 fabricated by this process,specifically around the impact of aging parameters on this alloy.In this study,the effects of aging parameters were studied by performing seven different heat treatments,including solutionising and aging treatments.Our results indicate that for LDED Inconel 718,a high temperature solution treatment of 1100℃for 1 h followed by single aging at 650℃for 20 h achieved a tensile strength and elongation of 1247 MPa and 23%,respectively.Further,results indicated that even with a shorter aging time of 10 h,γ′phase was found to be of comparable size to the standard double aged treatment.展开更多
Monel K-500 is a Ni–Cu alloy widely used in the marine and offshore industry due to their superior resistance to corrosion in seawater and hence easily degraded.To address this problem,laser-based directed energy dep...Monel K-500 is a Ni–Cu alloy widely used in the marine and offshore industry due to their superior resistance to corrosion in seawater and hence easily degraded.To address this problem,laser-based directed energy deposition(LDED)is used to repair or refabricate these high-value worn parts.To optimize the mechanical properties of repaired parts,the commonly applied solution and aging is not ideal because it also changes the properties of the base materials.Consequently,in situ control of the grain structures during the LDED process becomes an effective approach for high-performance repair.In this study,we fabricated a duplex grain structure with small grain size and low texture intensity using low laser power and scanning velocity.The duplex microstructure consists of short columnar grains and zigzag-distributed fine equiaxed grains.The formation of this grain structure is dependent on both the solidification and recrystallization mechanisms.The strength of this grain structure is improved to 523.5 MPa without the sacrifice of ductility,which is instead 20%higher than that of the counterpart consisting of typical columnar grains due to the grain refinement and crack toughening.The mechanical properties of the alloy with the duplex grain structure are even comparable to heat-treated Monel K-500 fabricated by wire arc additive manufacturing.This work provides valuable insights into the in situ optimization of the microstructure and mechanical properties of LDED-fabricated parts.展开更多
Microstructure with globularαphase is desirable as it contributes to preferable comprehensive mechanical properties for titanium alloys.However,titanium alloys fabricated by directed energy deposition(DED)are mainly ...Microstructure with globularαphase is desirable as it contributes to preferable comprehensive mechanical properties for titanium alloys.However,titanium alloys fabricated by directed energy deposition(DED)are mainly characterized by the lamellarαphase within the basket-weave microstructure,which often leads to severe anisotropy and inferior low cycle fatigue(LCF)properties.To address this,the subcritical annealing and the cyclic annealing were applied to DED Ti–6Al–4V in order to achieve the transformation from the lamellarαphase to the globularαphase.The microstructural characteristics and the globularization behavior ofαphase during heat treatment were investigated.The results show that the aspect ratio ofαis significantly decreased with the subcritical annealing due to the coarsening of lamellarα.Furthermore,the globularαis obtained with the cyclic annealing as a combination result of the termination dissolution and the side surface growth of the lamellarα.These contribute to a pronounced reduction of 85.4%in the ductility anisotropy,compared with the as-built specimens,and superior comprehensive mechanical properties including LCF are achieved with the formation of globularα.展开更多
Oxide melt growth ceramics(OMGCs)exhibit excellent performance and microstructure stability near their melt-ing point and are expected to become a new structural material for long-term stable service in extremely high...Oxide melt growth ceramics(OMGCs)exhibit excellent performance and microstructure stability near their melt-ing point and are expected to become a new structural material for long-term stable service in extremely high-temperature water-oxygen environments.Owing to its unique advantages of high efficiency,flexible manufac-turing,and near-net shaping,laser directed energy deposition(LDED)has become a promising technology for the rapid preparation of high-performance OMGCs.However,owing to the limited understanding of the crack-ing mechanism,the severe cracking problem that hinders OMGCs-LDED towards engineering applications has not been resolved.Alumina/aluminum titanate(Al_(2)O_(3)/Al_(x)Ti_(y)O_(z),A/AT)ceramics are prepared using an LDED system and their cracking characteristics are investigated.Subsequently,numerical simulations are conducted to reveal the dominant factors and influencing mechanisms of the cracking behavior.The results demonstrate that the cracking nucleation process is mainly controlled by solidification defects,whereas the cracking propagation process is determined primarily by both the microstructure and stress level.This study provides a theoretical basis for the development of appropriate cracking suppression methods for OMGCs-LDED.展开更多
Mg-Gd-Y-Zr alloy,as a typical magnesium rare-earth(Mg-RE)alloy,is gaining popularity in the advanced equipment manufacturing fields owing to its noticeable age-hardening properties and high specific strength.However,i...Mg-Gd-Y-Zr alloy,as a typical magnesium rare-earth(Mg-RE)alloy,is gaining popularity in the advanced equipment manufacturing fields owing to its noticeable age-hardening properties and high specific strength.However,it is extremely challenging to prepare wrought components with large dimensions and complex shapes because of the poor room-temperature processability of Mg-Gd-Y-Zr alloy.Herein,we report a wire-arc directed energy deposited(DED)Mg-10.45Gd-2.27Y-0.52Zr(wt.%,GW102K)alloy with high RE content presenting a prominent combination of strength and ductility,realized by tailored nanoprecipitates through an optimized heat treatment procedure.Specifically,the solution-treated sample exhibits excellent ductility with an elongation(EL)of(14.6±0.1)%,while the aging-treated sample at 200°C for 58 h achieves an ultra-high ultimate tensile strength(UTS)of(371±1.5)MPa.Besides,the aging-treated sample at 250°C for 16 h attains a good strength-ductility synergy with a UTS of(316±2.1)MPa and a EL of(8.5±0.1)%.Particularly,the evolution mechanisms of precipitation response induced by various aging parameters and deformation behavior caused by nanoprecipitates type were also systematically revealed.The excellent ductility resulted from coordinating localized strains facilitated by active slip activity.And the ultra-high strength should be ascribed to the dense nano-β'hampering dislocation motion.Additionally,the shearable nano-β1 contributed to the good strength-ductility synergy.This work thus offers insightful understanding into the nanoprecipitates manipulation and performance tailoring for the wire-arc DED preparation of large-sized Mg-Gd-Y-Zr components with complex geometries.展开更多
A common challenge in direct energy deposition(DED)is eliminating the anisotropy in mechanical performance associated with microstructure and the formation of coarse columnar grains.In this work,a heterogeneous nuclea...A common challenge in direct energy deposition(DED)is eliminating the anisotropy in mechanical performance associated with microstructure and the formation of coarse columnar grains.In this work,a heterogeneous nucleation mechanism was introduced into the melt pool,and,from this mechanism,an almost fully equiaxed grain morphology was obtained in the DED of Ti-6 Al-3 Mo.Three types of grain morphologies in DED Ti-6 Al-3 Mo,including full columnar grains,near-equiaxed grains and almost fully equiaxed grains were obtained from premixed and satellite powder blends from Ti,6 wt.%Al and 3 wt.%Mo,respectively.Combined with the analysis of the interactions between powder particles and the melt pool in DED,the formation mechanism of the equiaxed grains caused by the incomplete melting of high melting point Mo particles was revealed.As the prior-βgrains transformed from coarse columnar grains to fine-equiaxed grains,the strong<100>fiber texture along the deposition direction was weakened,while the size of theα-laths in the prior-βgrains slightly decreased,and the selection ofα-variants was weakened.Due to the transformation of the prior-βgrains from coarse columnar grains to fine-equiaxed grains,the tensile strength of the deposited samples increased from 982 MPa to 1082 MPa,while the yield strength increased from 840 MPa to 922 MPa,and the elongation of the as-deposited alloy also increased from 9.0%to 9.8%,which confirmed that the presence of fine-equiaxed grains is beneficial to the strength and plasticity of the DED alloy.This work further demonstrates the role that satelliting powders can play in terms of enhancing the columnar to equiaxed transition(CET)behavior associated with DED.展开更多
基金the financial support by the Defense Industrial Technology Development Program(No.JCKY2020130C024)the National Science and Technology Major Project,China(No.Y2019-Ⅶ-0011-0151)the Science Center for Gas Turbine Project(No.P2022-C-Ⅳ-002-001)。
文摘Cracks have consistently been a significant challenge limiting the development of additive manufactured nickel-based superalloys.It is essential to investigate the location of cracks and their forming mechanism.This study extensively examines the impact of solidification process,microstructural evolution,and stress concentration on crack initiation during direct energy deposition(DED).The results emphasize that the crack formation is significantly related to large-angle grain boundaries,rapid cooling rates.Cracks caused by large-angle grain boundaries and a fast-cooling rate predominantly appear near the edge of the deposited samples.Liquation cracks are more likely to form near the top of the deposited sample,due to the presence ofγ/γ'eutectics.The secondary dendritic arm and the carbides in the interdendritic regions can obstruct liquid flow during the final stage of solidification,which results in the formation of solidification cracks and voids.This work paves the way to avoid cracks in nickel-based superalloys fabricated by DED,thereby enhancing the performance of superalloys.
基金financial support of the National Natural Science Foundation of China(Nos.52130110 and U22A20189)the Research Fund of the State Key Laboratory of Solidification Processing(No.2023-TS-10)。
文摘The microstructure characteristics and strengthening mechanism of Inconel738LC(IN-738LC) alloy prepared by using induction-assisted directed energy deposition(IDED) were elucidated through the investigation of samples subjected to IDED under 1050℃ preheating with and without hot isostatic pressing(HIP,1190℃,105 MPa,and 3 h).Results show that the as-deposited sample mainly consisted of epitaxial columnar crystals and inhomogeneously distributed γ’ phases in interdendritic and dendritic core regions.After HIP,grain morphology changed negligibly,whereas the size of the γ’ phase became increasingly even.After further heat treatment(HT,1070℃,2 h + 845℃,24 h),the γ’ phase in the as-deposited and HIPed samples presented a bimodal size distribution,whereas that in the as-deposited sample showed a size that remained uneven.The comparison of tensile properties revealed that the tensile strength and uniform elongation of the HIP + HTed sample increased by 5% and 46%,respectively,due to the synergistic deformation of bimodal γ’phases,especially large cubic γ’ phases.Finally,the relationship between phase transformations and plastic deformations in the IDEDed sample was discussed on the basis of generalized stability theory in terms of the trade-off between thermodynamics and kinetics.
基金supported by the National Natural Science Foundation of China(51975112,52375412)Fundamental Research Funds for Central Universities(N2203011)。
文摘Additive manufacturing provides achievability for the fabrication of bimetallic and multi-material structures;however,the material compatibility and bondability directly affect the parts’formability and final quality.It is essential to understand the underlying printability of different material combinations based on an adapted process.Here,the printability disparities of two common and attractive material combinations(nickel-and iron-based alloys)are evaluated at the macro and micro levels via laser directed energy deposition(DED).The deposition processes were captured using in situ high-speed imaging,and the dissimilarities in melt pool features and track morphology were quantitatively investigated within specific process windows.Moreover,the microstructure diversity of the tracks and blocks processed with varied material pairs was comparatively elaborated and,complemented with the informative multi-physics modeling,the presented non-uniformity in mechanical properties(microhardness)among the heterogeneous material pairs was rationalized.The differences in melt flow induced by the unlike thermophysical properties of the material pairs and the resulting element intermixing and localized re-alloying during solidification dominate the presented dissimilarity in printability among the material combinations.This work provides an in-depth understanding of the phenomenological differences in the deposition of dissimilar materials and aims to guide more reliable DED forming of bimetallic parts.
基金financially supported by Gansu Science and Technology Department(No.21ZD3GC001)。
文摘Direct energy deposition(DED)has great potential for the production of stainless steel matrix nanocomposite parts.However,the propensity of nanoparticle agglomeration leads to the difficulty in realizing homogenous dispersion of nanoparticles in the matrix.In this study,a series of agglomeration-free nanoWC-Co-reinforced 420 stainless steel matrix nanocomposite powders with high flowability were prepared by ball milling under the optimal parameters.The effect of ball milling time on the properties of the composite powders was investigated.Excellent powder properties ensure the DED processing performance.Furthermore,the corresponding composites were fabricated by DED,and the effects of nano-WC-Co content on the properties of the composites were comprehensively investigated.The contact angles between the single pass cladding layer and the substrate change with increasing nano-WC-Co content(decrease from 127.38°to 113.07°).The different contact angles will significantly influence the quality of the multipass cladding layer.Furthermore,the addition of nanoWC-Co leads not only to further grain refinement but also to more pronounced isotropy of the micros tructure.With the increase in nano-WC-Co content,the corrosion resistance is significantly improved(62.28%lower corrosion current for 420-15 wt%nano-WC-Co than for 420).
基金supported by the 2022 MTC Young Individual Research Grants(Grant No.M22K3c0097)the Singapore Research,Innovation and Enterprise(RIE)2025 PlanSingapore Aerospace Programme Cycle 16(Grant No.M2215a0073)。
文摘Lightweight aluminum(Al)alloys have been widely used in frontier fields like aerospace and automotive industries,which attracts great interest in additive manufacturing(AM)to process high-value Al parts.As a mainstream AM technique,laser-directed energy deposition(LDED)shows good scalability to meet the requirements for large-format component manufacturing and repair.However,LDED Al alloys are highly challenging due to their inherent poor printability(e.g.low laser absorption,high oxidation sensitivity and cracking tendency).To further promote the development of LDED high-performance Al alloys,this review offers a deep understanding of the challenges and strategies to improve printability in LDED Al alloys.The porosity,cracking,distortion,inclusions,element evaporation and resultant inferior mechanical properties(worse than laser powder bed fusion)are the key challenges in LDED Al alloys.Processing parameter optimizations,in-situ alloy design,reinforcing particle addition and field assistance are the efficient approaches to improving the printability and performance of LDED Al alloys.The underlying correlations between processes,alloy innovation,characteristic microstructures,and achievable performances in LDED Al alloys are discussed.The benchmark mechanical properties and primary strengthening mechanism of LDED Al alloys are summarized.This review aims to provide a critical and in-depth evaluation of current progress in LDED Al alloys.Future opportunities and perspectives in LDED high-performance Al alloys are also outlined.
基金the financial support of the Hunan Innovation Platform and Talent Plan(2022RC3033)Natural Science Foundation of Shandong Province(ZR2020ZD04)Ganzhou Science and Technology Planning Project(Grant No.Ganshikefa[2019]60)。
文摘Ni51Ti49 at.%bulk was additively manufactured by laser-directed energy deposition(DED)to reveal the microstructure evolution,phase distribution,and mechanical properties.It is found that the localized remelting,reheating,and heat accumulation during DED leads to the spatial heterogeneous distribution of columnar crystal and equiaxed crystal,a gradient distribution of Ni4Ti3 precipitates along the building direction,and preferential formation of Ni4Ti3 precipitates in the columnar zone.The austenite transformation finish temperature(Af)varies from-12.65℃(Z=33 mm)to 60.35℃(Z=10 mm),corresponding to tensile yield strength(σ0.2)changed from 120±30 MPa to 570±20 MPa,and functional properties changed from shape memory effect to superelasticity at room temperature.The sample in the Z=20.4 mm height has the best plasticity of 9.6%and the best recoverable strain of 4.2%.This work provided insights and guidelines for the spatial characterization of DEDed NiTi.
基金supported by the project CALIPSOplus under the Grant Agreement 730872 from the EU Framework Programme for Research and Innovation HORIZON 2020the financial support of the European Research Council(ERC)under the European Union’s Horizon 2020 research and innovation program(Grant No.771146 TOUGHIT)funded within the AIT’s strategic research portfolio 2022 and by the European Commission within the framework INTERREG V-A Austria–Czech Republic in the project“ReMaP“(Interreg project no.ATCZ229)。
文摘In recent years,wire-arc directed energy deposition(wa DED),which is also commonly known as wire-arc additive manufacturing(WAAM),has emerged as a promising new fabrication technique for magnesium alloys.The major reason for this is the possibility of producing parts with a complex geometry as well as a fine-grained microstructure.While the process has been shown to be applicable for Mg-Al-Zn alloys,there is still a lack of knowledge in terms of the influence of the WAAM process on the age-hardening response.Consequently,this study deals with the aging response of a WAAM AZ91 alloy.In order to fully understand the mechanisms during aging,first,the as-built condition was analyzed by means of high-energy X-ray diffraction(HEXRD)and scanning electron microscopy.These investigations revealed a finegrained,equiaxed microstructure with adjacent areas of alternating Al content.Subsequently,the difference between single-and double-step aging as well as conventional and direct aging was studied on the as-built WAAM AZ91 alloy for the first time.The aging response during the various heat treatments was monitored via in situ HEXRD experiments.Corroborating electron microscopy and hardness studies were conducted.The results showed that the application of a double-step aging heat treatment at 325℃with pre-aging at 250℃slightly improves the mechanical properties when compared to the single-step heat treatment at 325℃.However,the hardness decreases considerably after the pre-aging step.Thus,aging at lower temperatures is preferable within the investigated temperature range of 250-325℃.Moreover,no significant difference between the conventionally aged and directly aged samples was found.Lastly,the specimens showed enhanced precipitation kinetics during aging as compared to cast samples.This could be attributed to a higher amount of nucleation sites and the particular temperature profile of the solution heat treatment.
基金supported financially by the Chinese National Science and Technology Major Project“Aeroengine and Gas Turbine”(No.2017-VII-0008-0102)the National Key Research and Development Program of China(No.2019YFA0705300)+1 种基金the Shanghai Science and Technology Committee(No.19DZ1100704)Shanghai Sailing Program(No.19YF1415900)。
文摘The columnar-to-equiaxed transition(CET)or the formation of stray grains in the laser melting deposition is the least desirable for the repair of single-crystal blades.In this work,the forced water-cooling was conducted on a single-crystal Rene N5 substrate during the direct energy deposition(DED).The single track remelting,one-layer,two-layer,and eight-layer depositions were investigated to explore the grain growth mechanism.The solidification conditions of the DED process,including temperature field,temperature gradient,and solidification speed,were numerically analyzed by a finite element model.The single-track remelting results showed that the fraction of columnar crystal regions increases from55.81%in the air-cooled sample to 77.14%in the water-cooled one.The single-track deposits of one-and two-layer have the same trend,where the proportion of columnar crystal height was higher under the forced water-cooled condition.The electron backscattered diffraction(EBSD)grain-structure maps of an eight-layer deposit show that the epitaxial growth height increases from 1 mm in the air-cooling sample to 1.5 mm in the water-cooling one.The numerical results showed that the tempe rature gradient in[0011 direction was significantly increased by using forced water-cooling.In conclusion,the in-situ substrate cooling can become a potential method to promote epitaxial growth during DED via the influence on CET occurrence.
基金National Natural Science Foundation of China(Grant No.U21B2073)Natural Science Foundation of Shandong Provincial of China(Grant No.ZR2020ZD04)+2 种基金Hunan Provincial Key R&D Plan of China(Grant No.2021GK2009)Shenzhen Science and Technology Plan of China(Grant No.JCYJ20180508151903646)Hunan Provincial Innovation Platform and Talent Plan of China(Grant No.2022RC3033).
文摘An Al-Mg-Sc-Zr alloy was additively manufactured by laser direct energy deposition(DED)under different laser powers,and the microstructures and mechanical properties of the as-deposited samples were investigated.The samples showed a fully equiaxed grain structure with grain sizes of 2–30μm.Most of the blocky primary Al3(Sc,Zr)-precipitated phases(<5μm)were arranged along the grain boundaries.A small amount of fine granular secondary Al3(Sc,Zr)phases(<0.5μm)were precipitated owing to the cyclic heat treatment during the DED forming process.According to the EBSD(Electron backscatter diffraction)results,the texture index and strength of the sample were only slightly greater than 1,indicating that the material structure exhibited a certain but not obvious anisotropy.The sample in the horizontal direction had better yield strength,tensile strength,and elogation properties(399.87 MPa,220.96 MPa,9.13%)than that in the building direction(385.40 MPa,219.40 MPa,8.24%),although the sample in the〈XOZ〉plane had the finest equiaxed grains.The ductility of the〈XOZ〉sample deteriorated as the number of pores increased.
基金Project(2020JJ2046)supported by the Science Fund for Hunan Distinguished Young Scholars,ChinaProject(S2020GXKJGG0416)supported by the Special Project for Hunan Innovative Province Construction,China+1 种基金Project(2018RS3007)supported by the Huxiang Young Talents,ChinaProject(GuikeAB19050002)supported by the Science Project of Guangxi,China。
文摘NiTi shape memory alloy(SMA)with nominal composition of Ni 50.8 at%and Ti 49.2 at%was additively manufactured(AM)by selective laser melting(SLM)and laser directed energy deposition(DED)for a comparison study,with emphasis on its phase composition,microstructure,mechanical property and deformation mechanism.The results show that the yield strength and ductility obtained by SLM are 100 MPa and 8%,respectively,which are remarkably different from DED result with 700 MPa and 2%.The load path of SLM sample presents shape memory effect,corresponding to martensite phase detected by XRD;while the load path of DED presents pseudo-elasticity with austenite phase.In SLM sample,fine grain and hole provide a uniform deformation during tensile test,resulting in a better elongation.Furthermore,the nonequilibrium solidification was studied by a temperature field simulation to understand the difference of the two 3D printing methods.Both temperature gradient G and growth rate R determine the microstructure and phase in the SLM sample and DED sample,which leads to similar grain morphologies because of similar G/R.While higher G×R of SLM leads to a finer grain size in SLM sample,providing enough driving force for martensite transition and subsequently changing texture compared to DED sample.
基金This work was supported by National Key R&D Program of China(Grant No.2022YFB4601000).
文摘The effect of spatial temperature gradient on the microstructural evolution of a 308L stainless steel during the directed energy deposition(DED)process was experimentally investigated.A novel cooling system was designed and incorporated to a DED system in order to control the temperature gradient along the deposition direction during solidification.During deposition,the workpiece was placed on a lifting platform,and as the deposition process proceeded,the platform and workpiece were gradually lowered into cooling water so that the temperature gradient along the deposition direction could be controlled and maintained stable during the deposition process.The microstructure characterization results indicated that a deposition strategy with higher G and G/R values(where G is temperature gradient and R is solidification rate)produced finer cellular grains that were better aligned with the deposition direction,while a deposition strategy with lower G and G/R values produced columnar grains with larger primary arm spacing and less aligned with the deposition direction.
文摘Porosity is a common phenomenon and can significantly hinder the quality of the coating.Here,the pore formation mechanism and the characteristics of the single tracks of the W-C coating using directed energy deposition(DED)are systematically investigated.The forming quality of the tracks,the distribution of the pores,and the elemental distribution near the pores are analyzed by the observations of the cross-sections of the tracks.The temperature field of the melt pool is discussed comprehensively to reveal the pore formation mechanism.The results confirm that Ni and Co evaporated during the DED process due to the high temperature of the melt pool.Pores were continuously produced adjacent to the fusion line when the melt pool was about to solidify since the temperature at the solidification front was higher than the boiling point of Ni.The vaporization area at the fusion line was proposed,where Ni could also evaporate at the time the melt pool started to solidify.The relationship between the solidification rate,the size of the vaporization area and the DED parameters(laser power and scanning speed)was established to discuss the causes of severe pores above the fusion line.This work contains a practical guide to reduce or eliminate the porosity in the coating preparation process on the surface of the tungsten alloy.
基金This work was supported by the Key Research and Development Projects of Shaanxi Province(2023-YBGY-359)the China CEEC University Joint Education Project(2021108)+1 种基金the Science and Technology Plan of Xi'an City(21ZCZZHXJS-QCY6-0001,21CXLHTJSGG-QCY8-0003)the Open Fund of Key Laboratory of Plasma Dynamics of Air Force Engineering University(6142202210203).
文摘Meeting the damage tolerance requirements for engineering-grade titanium alloys pose a significant challenge in achieving high fracture toughness in direct energy deposition(DED)titanium alloys.This work primarily investigated the relationship between the microstructure and the fracture toughness of DED new Ti-6Al-4V-1Mo alloy.Two types of microstructures were designed via two process strategies:high-line energy density(HE)and low-line energy density(LE).Relative to LE samples,HE samples possess larger-sized microstructural characteristics(coarser grain boundaryα(α_(GB)),largerαcolonies,and coarserαlaths).Lessα/βphase boundaries were formed by coarserαlaths in the HE samples,increasing the movement of dislocations,resulting in tensile strength decreasing from 1007.1 MPa(LE)to 930.8 MPa(HE)and elongation increasing from 10.8%(LE)to 15.7%(HE).Also,HE samples exhibited an excellent fracture toughness of 114.0 MPa m^(1/2),significantly higher than that of LE samples(76.8 MPa m^(1/2)).An analysis of crack propagation paths was conducted to investigate the factors contributing to toughening.The primary factor enhancing toughness is the frequent obstruction of cracks by coarseαGB and largeαcolonies in HE samples.Particularly,the pretty large-angle deflections induced by the superposition effect of coarseαGB and largeαcolonies play a vital of significant role.These factors induced the long and tortuous high-energy pathways,which resulted in ultimately improved fracture toughness.The discovered microstructural toughening mechanisms can serve as a reference for future studies involving titanium alloys,offering insights on how to enhance fracture toughness by achieving similar characteristics.
基金supported by National Natural Science Foundation of China(Grant No.52071005)National Science and Technology Sup-porting Project of China(Grant No.JPPT-135-GH-2-036)Funda-mental Research Funds for the Central Universities of China(Grant No.030810).
文摘The application of titanium alloys in aerospace put forward the requirement for higher strength.Additive manu-facturing is a promising method for the efficient and economical processing of titanium alloys.However,research on the additive manufacturing of ultrahigh-strength titanium alloys is still limited.The mechanisms of microseg-regation for high alloying elements and poor plasticity are still not clear.In this study,an ultrahigh-strength titanium alloy Ti-4.5Al-5Mo-5V-6Cr-1Nb(TB18)was prepared using two methods:laser direct energy deposi-tion(LDED)and forging.The LDEDed alloy contains three zones with similar grain morphologies but different microstructure.The microsegregation of the alloy is limited due to the rapid solidification and almost eliminated after the thermal cycle and solution treatment.With stress relief treatment,the LDEDed alloy exhibits anisotropic mechanical properties.After solution and aging treatments,its ultimate strength is enhanced;however,its plas-ticity is relatively lower than that of the wrought alloy with equally high strength.The excellent balance of the strength and plasticity of the wrought alloy can be ascribed to the formation of𝛼WGB and multiscale𝛼laths,which provides enlightenment for optimizing the properties of the LDEDed alloy.
文摘Inconel 718 is a nickel-based superalloy of high interest in high temperature applications such as turbine parts.To be used in such applications,heat treatments are commonly applied to dissolute Laves phase and to achieve𝛾γ′phase.However,conventional heat treatment methods for wrought Inconel 718 may not be suitable for Inconel 718 fabricated by laser directed energy deposition(LDED)due to its unique microstructure formed during the rapid solidification process.There has been a lack of investigation in heat treatments for Inconel 718 fabricated by this process,specifically around the impact of aging parameters on this alloy.In this study,the effects of aging parameters were studied by performing seven different heat treatments,including solutionising and aging treatments.Our results indicate that for LDED Inconel 718,a high temperature solution treatment of 1100℃for 1 h followed by single aging at 650℃for 20 h achieved a tensile strength and elongation of 1247 MPa and 23%,respectively.Further,results indicated that even with a shorter aging time of 10 h,γ′phase was found to be of comparable size to the standard double aged treatment.
基金supported by Economic Development Board,Singapore and DNV Singapore Pte.Ltd.through Industrial Postgraduate Programme with Nanyang Technological University,Singapore,and the National Research Foundation,Prime Minister's Office,Singapore under its Medium-Sized Centre funding scheme through the Marine and Offshore Program.
文摘Monel K-500 is a Ni–Cu alloy widely used in the marine and offshore industry due to their superior resistance to corrosion in seawater and hence easily degraded.To address this problem,laser-based directed energy deposition(LDED)is used to repair or refabricate these high-value worn parts.To optimize the mechanical properties of repaired parts,the commonly applied solution and aging is not ideal because it also changes the properties of the base materials.Consequently,in situ control of the grain structures during the LDED process becomes an effective approach for high-performance repair.In this study,we fabricated a duplex grain structure with small grain size and low texture intensity using low laser power and scanning velocity.The duplex microstructure consists of short columnar grains and zigzag-distributed fine equiaxed grains.The formation of this grain structure is dependent on both the solidification and recrystallization mechanisms.The strength of this grain structure is improved to 523.5 MPa without the sacrifice of ductility,which is instead 20%higher than that of the counterpart consisting of typical columnar grains due to the grain refinement and crack toughening.The mechanical properties of the alloy with the duplex grain structure are even comparable to heat-treated Monel K-500 fabricated by wire arc additive manufacturing.This work provides valuable insights into the in situ optimization of the microstructure and mechanical properties of LDED-fabricated parts.
基金This work was financially supported by the National Natural Science Foundation of China(No.52275381)the Nation Defense Basic Scientific Research Program of China(No.JCKY2017204A021)the Shaanxi Province double chain fusion project(No.2021LLRH-08).
文摘Microstructure with globularαphase is desirable as it contributes to preferable comprehensive mechanical properties for titanium alloys.However,titanium alloys fabricated by directed energy deposition(DED)are mainly characterized by the lamellarαphase within the basket-weave microstructure,which often leads to severe anisotropy and inferior low cycle fatigue(LCF)properties.To address this,the subcritical annealing and the cyclic annealing were applied to DED Ti–6Al–4V in order to achieve the transformation from the lamellarαphase to the globularαphase.The microstructural characteristics and the globularization behavior ofαphase during heat treatment were investigated.The results show that the aspect ratio ofαis significantly decreased with the subcritical annealing due to the coarsening of lamellarα.Furthermore,the globularαis obtained with the cyclic annealing as a combination result of the termination dissolution and the side surface growth of the lamellarα.These contribute to a pronounced reduction of 85.4%in the ductility anisotropy,compared with the as-built specimens,and superior comprehensive mechanical properties including LCF are achieved with the formation of globularα.
基金supported by National Natural Science Founda-tion of China(Grant.Nos.51805070,51790172,52175291)Funda-mental Research Funds for the Central Universities of China(Grant.Nos.DUT22YG210,DUT22LAB117)+1 种基金Science Center for Gas Turbine Project of China(Grant.No.P2022-B-IV-012-001)Shenzhen Sci-ence and Technology Innovation Commission of China(Grant.No.JCYJ20210324115413036).
文摘Oxide melt growth ceramics(OMGCs)exhibit excellent performance and microstructure stability near their melt-ing point and are expected to become a new structural material for long-term stable service in extremely high-temperature water-oxygen environments.Owing to its unique advantages of high efficiency,flexible manufac-turing,and near-net shaping,laser directed energy deposition(LDED)has become a promising technology for the rapid preparation of high-performance OMGCs.However,owing to the limited understanding of the crack-ing mechanism,the severe cracking problem that hinders OMGCs-LDED towards engineering applications has not been resolved.Alumina/aluminum titanate(Al_(2)O_(3)/Al_(x)Ti_(y)O_(z),A/AT)ceramics are prepared using an LDED system and their cracking characteristics are investigated.Subsequently,numerical simulations are conducted to reveal the dominant factors and influencing mechanisms of the cracking behavior.The results demonstrate that the cracking nucleation process is mainly controlled by solidification defects,whereas the cracking propagation process is determined primarily by both the microstructure and stress level.This study provides a theoretical basis for the development of appropriate cracking suppression methods for OMGCs-LDED.
基金The authors declare that they have no competing financial interests that could have influenced the work reported in this paper.
文摘Mg-Gd-Y-Zr alloy,as a typical magnesium rare-earth(Mg-RE)alloy,is gaining popularity in the advanced equipment manufacturing fields owing to its noticeable age-hardening properties and high specific strength.However,it is extremely challenging to prepare wrought components with large dimensions and complex shapes because of the poor room-temperature processability of Mg-Gd-Y-Zr alloy.Herein,we report a wire-arc directed energy deposited(DED)Mg-10.45Gd-2.27Y-0.52Zr(wt.%,GW102K)alloy with high RE content presenting a prominent combination of strength and ductility,realized by tailored nanoprecipitates through an optimized heat treatment procedure.Specifically,the solution-treated sample exhibits excellent ductility with an elongation(EL)of(14.6±0.1)%,while the aging-treated sample at 200°C for 58 h achieves an ultra-high ultimate tensile strength(UTS)of(371±1.5)MPa.Besides,the aging-treated sample at 250°C for 16 h attains a good strength-ductility synergy with a UTS of(316±2.1)MPa and a EL of(8.5±0.1)%.Particularly,the evolution mechanisms of precipitation response induced by various aging parameters and deformation behavior caused by nanoprecipitates type were also systematically revealed.The excellent ductility resulted from coordinating localized strains facilitated by active slip activity.And the ultra-high strength should be ascribed to the dense nano-β'hampering dislocation motion.Additionally,the shearable nano-β1 contributed to the good strength-ductility synergy.This work thus offers insightful understanding into the nanoprecipitates manipulation and performance tailoring for the wire-arc DED preparation of large-sized Mg-Gd-Y-Zr components with complex geometries.
基金financially supported by the National Key Research and Development Program of China(No.2016YFB1100103)the Natural Science Basic Research Plan in Shaanxi Province of China(No.2020JM-239)+2 种基金the National Natural Science Foundation of China(No.51475380)the Fundamental Research Funds for the Central Universities CHD(No.300102319208)the National Training Program of Innovation and Entrepreneurship for Undergraduates(No.S202010710142)。
文摘A common challenge in direct energy deposition(DED)is eliminating the anisotropy in mechanical performance associated with microstructure and the formation of coarse columnar grains.In this work,a heterogeneous nucleation mechanism was introduced into the melt pool,and,from this mechanism,an almost fully equiaxed grain morphology was obtained in the DED of Ti-6 Al-3 Mo.Three types of grain morphologies in DED Ti-6 Al-3 Mo,including full columnar grains,near-equiaxed grains and almost fully equiaxed grains were obtained from premixed and satellite powder blends from Ti,6 wt.%Al and 3 wt.%Mo,respectively.Combined with the analysis of the interactions between powder particles and the melt pool in DED,the formation mechanism of the equiaxed grains caused by the incomplete melting of high melting point Mo particles was revealed.As the prior-βgrains transformed from coarse columnar grains to fine-equiaxed grains,the strong<100>fiber texture along the deposition direction was weakened,while the size of theα-laths in the prior-βgrains slightly decreased,and the selection ofα-variants was weakened.Due to the transformation of the prior-βgrains from coarse columnar grains to fine-equiaxed grains,the tensile strength of the deposited samples increased from 982 MPa to 1082 MPa,while the yield strength increased from 840 MPa to 922 MPa,and the elongation of the as-deposited alloy also increased from 9.0%to 9.8%,which confirmed that the presence of fine-equiaxed grains is beneficial to the strength and plasticity of the DED alloy.This work further demonstrates the role that satelliting powders can play in terms of enhancing the columnar to equiaxed transition(CET)behavior associated with DED.