Effect of yttrium and calcium additions on electrochemical behaviors and discharge performance of AZ80 anodes for Mg-air battery

The effects of yttrium(Y)and yttrium+calcium(Y+Ca)additions on the electrochemical properties and discharge performance of the as-extruded Mg−8Al−0.5Zn−0.2Mn(AZ80)anodes for Mg−air batteries were investigated.The results show that the addition of 0.2 wt.%Y increased the corrosion resistance and discharge activity of AZ80 anode.This was attributed to the fine and sphericalβ-Mg_17)Al_(12) phases dispersing evenly in AZ80+0.2Y alloy,which suppressed the localized corrosion and severe“chunk effect”,and facilitated the rapid activation ofα-Mg.Combinative addition of 0.2 wt.%Y and 0.15 wt.%Ca generated grain refinement and a reduction of theβ-Mg_17)Al_(12) phase,resulting in a further enhancement in discharge voltage.However,the incorporation of Ca in Mg_17)Al_(12) and Al_(2)Y compounds compromised the corrosion resistance and anodic efficiency of AZ80+0.2Y+0.15Ca anode.Consequently,AZ80+0.2Y anode exhibited excellent overall discharge performance,with the peak discharge capacity and anodic efficiency of 1525 mA·h·g^(−1) and 67%at 80 mA/cm^(2),13%and 14%higher than those of AZ80 anode,respectively.

Improving the Intermittent Discharge Performance of Mg–Air Battery by Using Oxyanion Corrosion Inhibitor as Electrolyte Additive

A widely used oxyanion corrosion inhibitor（Li2CrO4） was used as electrolyte additive（3.5 wt% Na Cl solution was used as electrolyte solution） for Mg–air battery. The potentiodynamic polarization tests showed that the presence of 0.1 wt% Li2CrO4in the Na Cl electrolyte reduced enormously the corrosion current density of the tested AZ31 Mg alloys.According to the intermittent discharge tests, the use of 0.1 wt% Li2CrO4 as electrolyte additive increased the anode efficiency of the Mg–air battery by 28.4%. The addition of 0.1 wt% Li2CrO4reduced the anode self-corrosion rate of the battery in the intermittent stage effectively. The product film after discharge was observed by scanning electron microscope, and the Mg–air battery containing 0.1 wt% Li2CrO4has a loose product film, which is beneficial to its discharge performance. So using Li2CrO4 as electrolyte additive could improve the intermittent discharge performance of Mg–air battery. And the use of oxyanion corrosion inhibitor as electrolyte additive may be an excellent way to improve the intermittent discharge performance of Mg–air battery.

Microstructures and Properties of Honeycomb Sulfur/carbon Black/MoS_(2) Composites

Microstructure and property of sulfur/carbon black composites prepared by ball milling were studied.Sulfur/carbon black composites were obtained by melting the mixture of sulfur and carbon black in 155℃and dispersing evenly in carbon black after hydrothermal reaction.Thus,its conductive properties were improved.Moreover,microstructure and property of honeycomb sulfur/carbon black/MoS_(2) prepared by hydrothermal method as a cathode material for lithium-sulfur batteries were studied.The initial discharge specific capacity of the material at 0.2 A/g current density is 838.495 mA·h/g,and the 55.14%after 100 weeks of cycling.It is indicated that MoS_(2) can not only combine with polysulfides through electrostatic action or the action of chemical bonds,but also honeycomb porous structure.MoS_(2) can fix polysulfides groups and prevent their shuttle.Therefore,the cycling performance of the battery is effectively improved.

Synthesis and electrochemical performances of LiCoO_2 recycled from the incisors bound of Li-ion batteries

A new LiCoO2 recovery technology for Li-ion batteries was studied in this paper. LiCoO2 was peeled from the Al foil with dimethyl acetamide （DMAC）, and then polyvinylidene fluoride （PVDF） and carbon powders in the active material were eliminated by high temperature calcining. Subsequently, Li2CO3, LiOH-H20 and LiAc-2H2O were added into the recycled powders to adjust the Li/Co molar ratio to 1.00. The new LiCoO2 was obtained by calcining the mixture at 850℃ for 12 h in air. The structure and morphology of the recycled powders and resulting samples were studied by XRD and SEM techniques, respectively. The layered structure of LiCoO2 synthesized by adding Li2CO3 is the best, and it is found to have the best characteristics as a cathode material in terms of charge-discharge capacity and cycling performance. The first discharge capacity is 160 mAh·g^-1 between 3.0-4.3 V. The discharge capacity after cycling for 50 times is still 145.2 mAh·g^-1.

Discharge properties and electrochemical behaviors of AZ80-La-Gd magnesium anode for Mg-air battery

In this work,the discharge properties and electrochemical behaviors of as-cast AZ80-La-Gd anode for Mg-air battery have been investigated and compared with the AZ80 anode.The microstructure evolution,electrochemical behaviors and surface morphologies after discharge have been discussed to connect the discharge properties.The results indicate that the modified AZ80-La-Gd is an outstanding candidate for anode for Mg-air batter,which has high cell voltage,stable discharge curves,good specific capacity and energy,and good anodic efficiency.It exhibits the best anodic efficiency,specific capacity and energy of 76.45%,1703.6 mAh·g^(-1)and 2186.3 mWh·g^(-1),respectively,which are20.24%,18.92%and 25.71%higher than values for AZ80 anode.Such excellent discharge performance is attributed to the Al-RE particles.They refine the Mg_(17)Al_(12)phase and therefore improve the self-corrosion resistance and desorption ability of AZ80 anode.

Corrosion and discharge behavior of Mg−xLa alloys(x=0.0−0.8) as anode materials

The corrosion and discharge performances of binary Mg−xLa(x=0.2−0.8,wt.%)alloys as anode materials for Mg-based batteries were evaluated.Microstructure,hydrogen evolution,mass loss,electrochemical behavior,and half-cell discharge capabilities were characterized.The results show that the corrosion rate of the Mg matrix was decreased by alloying with La,and this could be attributed to the formation of a protective La2O3-containing film on the surface of the alloy.The Mg−0.2La alloy displayed the lowest corrosion rate,i.e.,2.4 mm/a in a 3.5 wt.%NaCl solution,Furthermore,the discharge performance of Mg−0.4La alloy was superior to that of pure Mg and other Mg−La alloys;this could be associated with the modified microstructure of the Mg−0.4La alloy,which decreased the self-corrosion and accelerated the detachment of the discharge products.

Microstructure and battery performance of Mg-Zn-Sn alloys as anodes for magnesium-air battery

Four Mg-x Zn-y Sn(x=2,4 and y=1,3 wt.%)alloys are investigated as anode materials for magnesium-air(Mg-air)battery.The self-corrosion and battery discharge behavior of these four Mg-Zn-Sn alloys are analyzed by electrochemical measurements and Mg-air battery tests.The results show that addition of Sn stimulates the electrochemical activity and significantly improves the anodic efficiency and specific capacity of Mg-Zn alloy anodes.Among the four alloy anodes,Mg-2Zn-3Sn(ZT23)shows the best battery discharge performance at low current densities(≤5 m A cm^(-2)),achieving high energy density of 1367 m Wh g^(-1)at 2 mA cm^(-2).After battery discharging,the surface morphology and electrochemical measurement results illustrate that a ZnO and SnO/SnO_(2)mixed film on alloy anode surface decreases self-corrosion and improves anodic efficiency during discharging.The excessive intermetallic phases lead to the failure of passivation films,acting as micro-cathodes to accelerate self-corrosion.

Physical Properties and Electrochemical Performance of Solid K_2FeO_4 Samples Prepared by Ex-situ and in-situ Electrochemical Methods

K2FeO4 powders were synthesized by the ex-situ and in-situ electrochemical methods, respectively, and characterized by infrared spectrum （IR）, scanning electron microscopy （SEM）, X-ray powder diffraction （XRD） and BET. Their electrochemical performances were investigated by means of galvanostatic discharge and electrochemi-cal impedance spectroscopy （EIS）. The results of physical characterization showed that the two samples have simi-lar structural features, but their surface morphologies and oriented growth of the crystals are different, which results in smaller specific surface area and lower solubility of the ex-situ electrosynthesized K2FeO4 sample. The results of discharge experiments indicated that the ex-situ electrosythesized K2FeO4 electrode has much larger discharge ca-pacity and lower electrode polarization than the in-situ electrosynthesized K2FeO4 electrode. It was found from the results of EIS that lower electrochemical polarization might be responsible for the improvement on the discharge performance of the ex-situ electrosynthesized K2FeO4 electrode.

Investigation of short-channel design on performance optimization effect of Hall thruster with large height–radius ratio

In this study,the neutral gas distribution and steady-state discharge under different discharge channel lengths were studied via numerical simulations.The results show that the channel with a length of 22 mm has the advantage of comprehensive discharge performance.At this time,the magnetic field intensity at the anode surface is 10%of the peak magnetic field intensity.Further analysis shows that the high-gas-density zone moves outward due to the shortening of the channel length,which optimizes the matching between the gas flow field and the magnetic field,and thus increases the ionization rate.The outward movement of the main ionization zone also reduces the ion loss on the wall surface.Thus,the propellant utilization efficiency can reach a maximum of 96.8%.Moreover,the plasma potential in the main ionization zone will decrease with the shortening of the channel.The excessively short-channel will greatly reduce the voltage utilization efficiency.The thrust is reduced to a minimum of 46.1 m N.Meanwhile,because the anode surface is excessively close to the main ionization zone,the discharge reliability is also difficult to guarantee.It was proved that the performance of Hall thrusters can be optimized by shortening the discharge channel appropriately,and the specific design scheme of short-channel of HEP-1350 PM was defined,which serves as a reference for the optimization design of Hall thruster with large height–radius ratio.The shortchannel design also helps to reduce the thruster axial dimension,further consolidating the advantages of lightweight and large thrust-to-weight ratio of the Hall thruster with large height–radius ratio.

Preparation of porous Mg electrode by electrodeposition

In order to obtain a porous Mg electrode with a stable skeleton, organic Mg fuel cell （OMFC）, the electrochemical behavior of Mg deposition on Cu and Ni metallic substrates in 1 mol/L EtMgBr/THF solution was investigated by SEM, EDS and electrochemical methods. The experimental results show that Mg can be electrodeposited on both substrates, as a continuous layer on a Cu substrate. Accordingly, an approach for producing a porous Mg electrode with a stable skeleton of OMFC was proposed by means of electrodeposition of Mg on a foamed Ni substrate with a layer of Cu pre-plating. The discharge performance of this porous Mg electrode of OMFC is superior to that of a planar Mg electrode.

Numerical Simulation and Optimization of the Gas-Solid Coupled Flow Field and Discharging Performance of Straw Crushers

The quality of crushing,power consumption,and discharging performance of a straw crusher are greatly influenced by the characteristics of its internalflowfield.To enhance the straw crusher’sflowfield properties and improve the efficiency with which crushed material is discharged,first,the main structural parameters influencing the airflow in the crusher are discussed.Then,the coupled gas-solidflowfield in the straw crusher is numerically calculated through solution of the Navier-Stokes equations and application of the discrete element method(DEM).Finally,the discharge performance index of the crusher is examined through detailed analysis of the crushed material dynamics.Additionally,a multi-island genetic algorithm is used to optimize the structure and operational factors that have significant effects on the discharge performance.With optimization,the accumulation rate of crushed materials in the bottom region of the straw crusher decreases by 20.08%,and the massflow rate at the discharge outlet increases by 11.63%.

Experimental and numerical investigation of a Hall thruster with a chamfered channel wall

A discharge channel with a chamfered wall not only has application in the design of modern Hall thrusters, but also exists where the channel wall is eroded, and so is a common status for these units. In this paper, the laws and mechanisms that govern the effect of the chamfered wall on the performance of a Hall thruster are investigated. By applying both experimental measurement and particle-in-cell simulation, it is determined that there is a moderate chamfer angle that can further improve the optimal performance obtained with a straight channel. This is because the chamfering of the wall near the channel exit can enhance ion acceleration and effectively reduce ion recombination on the wall, which is favorable to the promotion of the thrust and efficiency. However, the chamfer angle should not be too large; otherwise, both the density of the propellant gas and the distribution of the plasma potential in the channel are influenced, which is undesirable for efficient propellant utilization and beam concentration. Therefore, it is suggested that the chamfer shape of the channel wall is an important factor that must be carefully considered in the design of Hall thrusters.

Numerical multi-physical optimization of operating condition and current collecting setup for large-area solid oxide fuel cells

Due to the depletion of traditional fossil fuels and the aggravation of related environmental problems,hydrogen energy is gaining more attention all over the world.Solid oxide fuel cell(SOFC)is a promising power generation technology operating on hydrogen with a high efficiency.To further boost the power output of a single cell and thus a single stack,increasing the cell area is an effective route.However,it was recently found that further increasing the effective area of an SOFC single cell with a flat-tubular structure and symmetric double-sided cathodes would result in a lower areal performance.In this work,a multi-physical model is built to study the effect of the effective area on the cell performance.The distribution of different physical fields is systematically analyzed.Optimization of the cell performance is also pursued by systematically tuning the cell operating condition and the current collection setup.An improvement of 42%is revealed by modifying the inlet gas flow rates and by enhancing the current collection.In the future,optimization of cell geometry will be performed to improve the homogeneity of different physical fields and thus to improve the stability of the cell.

High energy storage properties in Ca_(0.7)La_(0.2)TiO_(3)-modified NaNbO_(3)-based lead-free antiferroelectric ceramics

In this work,(1−x)(0.92NaNbO_(3)-0.08BaTiO_(3))-xCa_(0.7)La_(0.2)TiO_(3)(NNBT-xCLT)ceramics were successfully designed and pre­pared by the solid-state reaction method.Investigations on the structure,dielectric,and energy storage properties were performed.The NNBT-0.25CLT ceramic with orthorhombic phase at room temperature was found to exhibit extremely small grain size and compacted microstructure.A large Wrec of 3.1 J/cm^(3) and a highηof 91.5%under the electric field of 360 kV/cm were achieved simultaneously in the sample.In addition,the energy storage performance of the sample exhibits thermal stability over the tem­perature range of 25-140°C and the frequency range of 5-500 Hz.The charge and discharge tests reveal that the ceramic shows a large current density CD of 965 A/cm2 and power density PD of 154 MW/cm^(3).This work demonstrates that the NNBT-0.25CLT ceramic is a prospective energy storage material for potential application in the field of pulsed power devices.