Comparison of displacement damage effects on the dark signal in CMOS image sensors induced by CSNS back-n and XAPR neutrons

This study investigates the effects of displacement damage on the dark signal of a pinned photodiode CMOS image sensor(CIS)following irradiation with back-streaming white neutrons from white neutron sources at the China spallation neutron source(CSNS)and Xi'an pulsed reactor(XAPR).The mean dark signal,dark signal non-uniformity(DSNU),dark signal distribution,and hot pixels of the CIS were compared between the CSNS back-n and XAPR neutron irradiations.The nonionizing energy loss and energy distribution of primary knock-on atoms in silicon,induced by neutrons,were calculated using the open-source package Geant4.An analysis combining experimental and simulation results showed a noticeable proportionality between the increase in the mean dark signal and the displacement damage dose(DDD).Additionally,neutron energies influence DSNU,dark signal distribution,and hot pixels.High neutron energies at the same DDD level may lead to pronounced dark signal non-uniformity and elevated hot pixel values.

Longitudinal vibration characteristics of a tapered pipe pile considering the vertical support of surrounding soil and construction disturbance

This research is concentrated on the longitudinal vibration of a tapered pipe pile considering the vertical support of the surrounding soil and construction disturbance.First,the pile-soil system is partitioned into finite segments in the vertical direction and the Voigt model is applied to simulate the vertical support of the surrounding soil acting on the pile segment.The surrounding soil is divided into finite ring-shaped zones in the radial direction to consider the construction disturbance.Then,the shear complex stiffness at the pile-soil interface is derived by solving the dynamic equilibrium equation for the soil from the outermost to innermost zone.The displacement impedance at the top of an arbitrary pile segment is obtained by solving the dynamic equilibrium equation for the pile and is combined with the vertical support of the surrounding soil to derive the displacement impedance at the bottom of the upper adjacent segment.Further,the displacement impedance at the pile head is obtained based on the impedance function transfer technique.Finally,the reliability of the proposed solution is verified,followed by a sensitivity analysis concerning the coupling effect of the pile parameters,construction disturbance and the vertical support of the surrounding soil on the displacement impedance of the pile.

Visualization of real-time displacement time history superimposed with dynamic experiments using wireless smart sensors and augmented reality

Wireless smart sensors(WSS)process field data and inform inspectors about the infrastructure health and safety.In bridge engineering,inspectors need reliable data about changes in displacements under loads to make correct decisions about repairs and replacements.Access to displacement information in the field and in real-time remains a challenge as inspectors do not see the data in real time.Displacement data from WSS in the field undergoes additional processing and is seen at a different location.If inspectors were able to see structural displacements in real-time at the locations of interest,they could conduct additional observations,creating a new,information-based,decision-making reality in the field.This paper develops a new,human-centered interface that provides inspectors with real-time access to actionable structural data during inspection and monitoring enhanced by augmented reality(AR).It summarizes and evaluates the development and validation of the new human-infrastructure interface in laboratory experiments.The experiments demonstrate that the interface that processes all calculations in the AR device accurately estimates dynamic displacements in comparison with the laser.Using this new AR interface tool,inspectors can observe and compare displacement data,share it across space and time,visualize displacements in time history,and understand structural deflection more accurately through a displacement time history visualization.

Wireless Self-Powered Vibration Sensor System for Intelligent Spindle Monitoring

In recent years,high-end equipment is widely used in industry and the accuracy requirements of the equipment have been risen year by year.During the machining process,the high-end equipment failure may have a great impact on the product quality.It is necessary to monitor the status of equipment and to predict fault diagnosis.At present,most of the condition monitoring devices for mechanical equipment have problems of large size,low precision and low energy utilization.A wireless self-powered intelligent spindle vibration acceleration sensor system based on piezoelectric energy harvesting is proposed.Based on rotor sensing technology,a sensor is made to mount on the tool holder and build the related circuit.Firstly,the energy management module collects the mechanical energy in the environment and converts the piezoelectric vibration energy into electric energy to provide 3.3 Vfor the subsequent circuit.The lithium battery supplies the system with additional power and monitors’the power of the energy storage circuit in real-time.Secondly,a three-axis acceleration sensor is used to collect,analyze and filter a series of signal processing operations of the vibration signal in the environment.The signal is sent to the upper computer by wireless transmission.The host computer outputs the corresponding X,Y,and Z channel waveforms and data under the condition of the spindle speed of 50∼2500 r/min with real-time monitoring.The KEIL5 platform is used to develop the system software.The small-size piezoelectric vibration sensor with high-speed,high-energy utilization,high accuracy,and easy installation is used for spindle monitoring.The experiment results show that the sensor system is available and practical.

Test and analysis of dynamic compaction vibration based on piezoelectric sensor

The paper takes a new campus project site of Shanxi university town for example, tests the influence of dynamic com- paction vibration and vibration isolation effect of isolation trench on this ground, and compares the influences of the dynamic compaction vibration on surrounding buildings with isolation trench and without it. Furthermore, the attenuation law of dy- namic compaction vibration in fill foundation of the loess area under different tamping energy and how to determine safe distance of dynamic compaction construction are studied. And then the quantitative relationship between acceleration and vibration source in new campus project site is presented. We derive the evaluation method that dynamic compaction construction affects adjacent buildings by contrasting with the existing standards and norms. The monitoring results show that isolation trench makes the amplitude attenuation of the horizontal velocity of dynamic compaction vibration reach above 75%, and the safe dis- tance be 30 m under the tamping energy of 6 000 kN · m. Therefore, isolation trench is better for vibration reduction under dynamic compaction construction.

Impact of the Foucault Current and Its Vibration Noise Reduction on Bracket Features for AMDT

This manuscript explores the influences of the Foucault current on bracket vibration. Noise measurements are obtained in conditions that the coils are enclosed by the bracket, and exposed to the air for confirming the impact of Foucault current on bracket vibration. The outcomes illustrate that the bracket increases the primary noise to 21 d B. Throughout investigational modal computation, ordinary frequencies of the coils stay afar from the exciting frequency of 100 Hz but the ordinary frequency 72.924 Hz of the bracket stands near to 100 Hz, which similarly explicates the upsurge of the noise level. To do the computations on bracket vibrations instigated by the Foucault current, a finite-element method(FEM) has been utilized for evaluating the eddy current density, electromagnetic forces(EMF), coupled with bracket response in frequency domain. The calculations displayed a proper approval by mean of theoretic investigations, and the simulations analyzed effectively the bracket vibration produced by Eddy current, and the electromagnetic force(EMF). Referring to the simulation, the primary vibration characteristics, and noise level, the method by applying weights(stress) on the top bracket of transformer is proposed to lessen the vibration amplitude, and noise level. To indorse the utility, and application of the suggested technique, the experiment results are obtained, analyzed, and compared with those of simulations, primary vibration characteristics, and noise level.

HIGH TEMPERATURE DISPLACEMENT SENSOR

A high temperature displacement sensor based on the principle of eddy-current is investigated. A new temperature compensation technique by using eddy-current effect is presented to satisfy the special requirement at high temperature up to 550℃. The experiment shows that the temperature compensation technique leads to good temperature stability for the sensors. The variation of the sensitivity as well as the temperature drift of the sensor with temperature compensation technique is only about 7.4% and 90-350 mV at 550 ℃ compared with that at room temperature, and that of the sensor without temperature compensation technique is about 31.2% and 2-3 V at 550 ℃ compared with that at room temperature. A new dynamic calibration method for the eddy-current displacement sensor is presented, which is very easy to be realized especially in high frequency and at high temperatures. The high temperature displacement sensors developed are successfully used at temperature up to 550 ℃ in a magnetic bearing system for more than 100 h.

Vibration analysis of a new polymer quartz piezoelectric crystal sensor for detecting characteristic materials of volatility liquid

We present a new polymer quartz piezoelectric crystal sensor that takes a quartz piezoelectric crystal as the basal material and a nanometer nonmetallic polymer thin film as the surface coating based on the principle of quartz crystal microbalance(QCM). The new sensor can be used to detect the characteristic materials of a volatile liquid. A mechanical model of the new sensor was built, whose structure was a thin circle plate composing of polytef/quartz piezoelectric/polytef. The mechanical model had a diameter of 8 mm and a thickness of 170 μm. The vibration state of the model was simulated by software ANSYS after the physical parameters and the boundary condition of the new sensor were set. According to the results of experiments, we set up a frequency range from 9.995850 MHz to 9.997225 MHz, 17 kinds of frequencies and modes of vibration were obtained within this range. We found a special frequency fspof 9.996358 MHz. When the resonant frequency of the new sensor's mechanical model reached the special frequency, a special phenomenon occurred. In this case, the amplitude of the center point O on the mechanical model reached the maximum value. At the same time, the minimum absolute difference between the simulated frequency based on the ANSYS software and the experimental measured stable frequency was reached. The research showed that the design of the new polymer quartz piezoelectric crystal sensor perfectly conforms to the principle of QCM. A special frequency value fspwas found and subsequently became one of the most important parameters in the new sensor design.

Design and analysis of singal conditioning circuit for vibration sensor

A piezoelectric sensor charge/voltage conversion circuit is designed based on the principle that piezoelectric sensor can convert the vibration or shock acceleration into the charge proportionally.Effect of temperature characteristic of feedback capacitor on the switching circuit output is analyzed based on the acquisition and measurement system in this paper.The characteristics of different filters are analyzed,and the corresponding filter circuit is configured according to the actual sensor bandwidth.Experiments show that the circuit can effectively filter out noises among the vibration signal and obtain vibration signal accurately.

Low-frequency characteristics extension for vibration sensors

Traditional magneto-electric vibration sensors and servo accelerometers have severe shortcomings when used to measure vibration where low frequency components predominate.A low frequency characteristic extension for velocity vibration sensors is presented in this paper.The passive circuit technology,active compensation technology and the closed- cycle pole compensation technology are used to extend the measurable range and to improve low frequency characteristics of sensors.Thses three types of low frequency velocity vibration sensors have been developed and widely adopted in China.

Vibrations measurements for shrouded blades of steam turbines based oneddy current sensors with high frequency response

With the development of power plants towards high power and intelligent operation direction,the vibrations or failures of blades,especially the last stage blades in steam turbines,happen more frequently due to the unstable operating conditions brought by flexible operation.A vibration measuring method for the shrouded blades of a steam turbine based on eddy current sensors with high frequency response is proposed,meeting the requirements of non-contact heath monitoring.The eddy current sensors produce the signals which are related to the area changing of every blade’s shroud resulting from the rotation of stator.Then an improved blade tip timing(BTT)technique is proposed to detect the vibrations of shrouded blades by measuring the arrival time of each area changing signal.A structure of eddy current sensors is developed in steam turbines and an amplitude modulation/demodulation circuit is designed to improve the response bandwidth up to 250 kHz.Vibration tests for the last stage blades of a steam turbine were carried out and the results validate the efficiency of the improved BTT technique and the high frequency response of the eddy current sensors presented.

ACTIVE VIBRATION CONTROL OF A CANTILEVER BEAM USING PIEZOELECTRIC SENSORS AND ACTUATORS

The topic of vibration control with distributed actuators has been the subject of many researches. This paper is concerned with the vibration control of a cantilever beam equipped with piezoelectric ceramics as sensors and actuators. One piezoelectric ceramic is bonded to the structure and provides control input for the structure, while the other piezoelectric ceramic provides the feedback signal. An approach to identification and control is presented. Observation spillover is eliminated by prefiltering the sensor data. A procedure used to determine actuator and sensor location, is discussed based on the modes to be controlled. Finally, the experimental results are presented to verify the proposed method.

Comparison of enhancement techniques based on neural networks for attenuated voice signal captured by flexible vibration sensors on throats

Wearable flexible sensors attached on the neck have been developed to measure the vibration of vocal cords during speech.However,highfrequency attenuation caused by the frequency response of the flexible sensors and absorption of high-frequency sound by the skin are obstacles to the practical application of these sensors in speech capture based on bone conduction.In this paper,speech enhancement techniques for enhancing the intelligibility of sensor signals are developed and compared.Four kinds of speech enhancement algorithms based on a fully connected neural network(FCNN),a long short-term memory(LSTM),a bidirectional long short-term memory(BLSTM),and a convolutional-recurrent neural network(CRNN)are adopted to enhance the sensor signals,and their performance after deployment on four kinds of edge and cloud platforms is also investigated.Experimental results show that the BLSTM performs best in improving speech quality,but is poorest with regard to hardware deployment.It improves short-time objective intelligibility(STOI)by 0.18 to nearly 0.80,which corresponds to a good intelligibility level,but it introduces latency as well as being a large model.The CRNN,which improves STOI to about 0.75,ranks second among the four neural networks.It is also the only model that is able to achieves real-time processing with all four hardware platforms,demonstrating its great potential for deployment on mobile platforms.To the best of our knowledge,this is one of the first trials to systematically and specifically develop processing techniques for bone-conduction speed signals captured by flexible sensors.The results demonstrate the possibility of realizing a wearable lightweight speech collection system based on flexible vibration sensors and real-time speech enhancement to compensate for high-frequency attenuation.

An active temperature compensated fiber Bragg grating vibration sensor for high-temperature application

An active temperature compensated fiber Bragg grating(FBG)vibration sensor with a constant section cantilever beam is proposed for the simultaneous measurement of temperature and vibration,and the sensor is verified by a temperature compensation feedback system.The high-temperature vibration sensor is composed of a quartz cantilever beam and a femtosecond Bragg grating.The feedback control demodulation system of active temperature compensation can adjust the laser wavelength to stabilize the grating offset point and realize simultaneous measurement of temperature and vibration.On this basis,the performance of the sensor is tested and analyzed within the range of 20-400℃by setting up a high-temperature vibration test system.The experimental results show that the sensitivity of the sensor is about 132.33 mV/g,and the nonlinearity is about 3.33%.The sensitivity between the laser wavelength and temperature is about 0.01307 nm/℃.In addition,the active temperature compensated fiber Bragg grating vibration sensor has the advantages of a simple structure,stable performance,easy demodulation and high sensitivity.Moreover,the sensor can achieve high temperature vibration signal monitoring and has good practical application value.

Non—touch Fiber—optic Reflective Displacement Sensor for Roller Wear

By accurately measuring the displacement between the roller surface and the optical fiber probe relative to a null position, we can test the roller wear. The whole testing method and system were introduced. Each part of the testing system was illustrated. And also a novel fiber-optic sensor with three probes in equal transverse space is adopted. Using this sensor, the effects of fluctuations in the light source, reflectivity changing of target surface and the intensity losses in the fiber lines are automatically compensated. This method offers such advantages as non-contact, no electromagnetic interference, simplicity, low cost, high sensitivity, good accuracy and stability.

Nonlinear correction of photoelectric displacement sensor based on least square support vector machine

A model of correcting the nonlinear error of photoelectric displacement sensor was established based on the least square support vector machine.The parameters of the correcting nonlinear model,such as penalty factor and kernel parameter,were optimized by chaos genetic algorithm.And the nonlinear correction of photoelectric displacement sensor based on least square support vector machine was applied.The application results reveal that error of photoelectric displacement sensor is less than 1.5%,which is rather satisfactory for nonlinear correction of photoelectric displacement sensor.

Analytical Solution of Vibration Analysis on Fixed-Free Single-Walled Carbon Nanotube-Based Mass Sensor

Fixed-free single-walled carbon nanotubes (SWCNTs) have attracted a lot of interest in recent years due to their suitability for a wide range of applications, such as field emission and vacuum microelectronic devices, nanosensors, and nanoactuators. Based on a cantilever beam-bending model with a rigid mass at the free end and mode analysis, an analytical solution is developed in the present study to deal with the resonant frequency and mode shapes of a SWCNT- based mass sensor. The resonant frequency shift and mode shape of the fixed-free SWCNTs caused by the addition of a nanoscale particle to the beam tip are examined in order to explore the suitability of SWCNTs as a mass detector device. The simulation results reveal that the volume of the added particle has little effect on the first resonant frequency. In contrast, the second resonant frequency decreases with increasing the volume of the added particle. Furthermore, the resonant frequency shift of the first mode is very obvious for the amount of added mass, and the second resonant frequency decreases rapidly with increasing volume of added particle. Therefore, the first and second resonant frequencies can be used in the measurement of the mass of added particle and its volume, respectively.

SVD Approach for Actuator and Sensor Placement in Active Vibration Control of Large Cable Net Structures

The actuator and sensor placement problem for active vibration control of large cable net structures is investigated in this paper.Since the structures exhibit closely spaced modes in the range of low frequencies,the number of modes to be considered is quite large after modal truncation,while only a limited number of actuators and sensors are to be placed.This makes it hard to determine the actuator and sensor locations with the existing placement methods in the literature such as the methods based on the controllability/observability grammian.To deal with this issue,an actuator and sensor placement method based on singular value decompositions(SVD)of the input and output matrices is proposed,which guarantees the modal controllability and observability of the system.The effectiveness of the SVD based method is verified through numerical simulations in which comparisons are conducted between randomly-chosen locations and the optimal ones obtained by a genetic algorithm.

Sensor Layout of Hoisting Machinery Vibration Monitoring Based on Harmony Genetic Search Algorithm

With the construction of automated docks,health monitoring technology as a parallel safety assurance technology for unmanned hoisting machinery has become a hot spot in the development of the industry.Hoisting machinery has a huge structure and numerous welded joints.The complexity and nonlinearity of the welded structure itself makes the structural failure parts random and difficult to arrange for monitoring sensors.In order to solve the problem of effectiveness and stability of the sensor arrangement method for monitoring the structure of hoisting machinery.Using the global and local search capabilities enhanced by the complementary search mechanism,a structural vibration monitoring sensor placement algorithm based on the harmony genetic algorithm is proposed.Firstly,the model is established for modal analysis to obtain the displacement matrix of each mode.Secondly,the optimal parameter combination is established through parameter comparison,and the random search mechanism is used to quickly search in the modal matrix to obtain the preliminary solution,and then the preliminary solution is genetically summed The mutation operation obtains the optimized solution,and the optimal solution is retained through repeated iterations to realize the decision of the vibration sensor layout of the crane structure monitoring.Combining the comparison test of harmony genetic algorithm,harmony search algorithm and genet-ic algorithm,the fitness of harmony genetic algorithm in X,Y and Z directions were 0.0045,0.0084 and 0.0058,respectively,which were all optimal.And the average probability of deviating from the optimal path is 1.10%,19.34%,and 54.43%,which are also optimal.Harmony genetic algorithm has the advantages of simplicity,fastness and strong global search ability,and can obtain better fitness value and better search stability.

Analysis and compensation of low frequency characteristics of sensors for vibration testing

In view of the influence and harm of low frequency vibration environment on the structure of spaceflight products,a low frequency dynamic study method for piezoelectric sensor based on the dynamic system of sinusoidal pressure is proposed.This method uses a sinusoidal pressure dynamic system with two-way dual channel import and export synchronization technology to study the low frequency characteristics of a piezoelectric sensor of PCB company,and its lower cut-off frequency is 0.26 Hz.It is also studied that when the frequency of the measured vibration or shock signal is 1-200 kHz,the error range of signal positive pressure action time is 4.87%-0.03%.The dynamic compensation for the low frequency of the vibration sensor is carried out,and the compensation effect is good.