Thermal fatigue property of the divertor plate is one of the key issues that governs the lifetime of the divertor plate. Taking tungsten as surface material, a small-mock-up divertor plate was made by hot isostatic pr...Thermal fatigue property of the divertor plate is one of the key issues that governs the lifetime of the divertor plate. Taking tungsten as surface material, a small-mock-up divertor plate was made by hot isostatic press welding (HIP). A thermal cycling experiment for divertor mock-up was carried out in the vacuum, where a high-heat-flux electronic gun was used as the thermal source. A cyclic heat flux of 9 MW/m2 was loaded onto the mock-up, a heating duration of 20 s was selected, the cooling water flow rate was 80 ml/s. After 1000 cycles, the surface and the W/Cu joint of the mock-up did not show any damage. The SEM was used to analyze the microstructure of the welding joint, where no cracks were found also.展开更多
During the discharging of Tokamak devices, interactions between the core plasma and plasma-facing components (PFCs) may cause exorbitant heat deposition in the latter. This poses a grave threat to the lifetimes of PFC...During the discharging of Tokamak devices, interactions between the core plasma and plasma-facing components (PFCs) may cause exorbitant heat deposition in the latter. This poses a grave threat to the lifetimes of PFCs materials. An infrared (IR) diagnostic system consisting of an IR camera and an endoscope was installed on an Experimental Advanced Superconducting Tokamak (EAST) to monitor the surface temperature of the lower divertor target plate (LDTP) and to calculate the corresponding heat flux based on its surface temperature and physical structure, via the finite element method. First, the temperature obtained by the IR camera was calibrated against the temperature measured by the built-in thermocouple of EAST under baking conditions to determine the true temperature of the LDTP. Next, based on the finite element method, a target plate model was built and a discretization of the modeling domain was carried out. Then, a heat conduction equation and boundary conditions were determined. Finally, the heat flux was calculated. The new numerical tool provided results similar to those for DFLUX;this is important for future work on related physical processes and heat flux control.展开更多
A three-dimensional analysis model based on the finite element method （FEM） is developed, which can derive the evolution and distribution characteristics of heat flux deposited on the divertor plate from the surface...A three-dimensional analysis model based on the finite element method （FEM） is developed, which can derive the evolution and distribution characteristics of heat flux deposited on the divertor plate from the surface temperature measured by infrared thermography diagnostics. The numerical simulations of surface heating due to localized power bursts and the power deposition calculations demonstrate that this analysis can provide accurate results and useful information about localized hot spots compared with the normal one- and two-dimensional calculations. In this paper, the details of this three- dimensional analysis are presented, and some results in ohmic heating and electron cyclotron resonant heating （ECRH） discharge on HL-2A are given.展开更多
The influence of the J×B force on the topographical modification of W targets during a type-I-like ELM in ITER has been studied numerically. A two-dimensional(2D) fluid dynamics model is employed by solving liqui...The influence of the J×B force on the topographical modification of W targets during a type-I-like ELM in ITER has been studied numerically. A two-dimensional(2D) fluid dynamics model is employed by solving liquid hydrodynamic Navier-Stokes equation with the 2D heat conduction equation in addition to driving forces for surface topography, such as surface tension and pressure gradient, the J×B force is particularly addressed. The governing equations are solved with the finite volume method by adequate prediction of the moving solid-liquid interface. Numerical simulations are carried out for a range of type-I ELM characteristic parameters. Our results indicate that both the surface tension and the J×B force contributes to the melt motion of tungsten plates when the energy flux is under 3000 MW·m^(-2), the surface tension is a major driving force while the pressure gradient is negligible. Our results also indicate that the J×B force makes the small hills grow at different rates at both the crater edges under a type-I-like ELM heat load with a Gaussian power density profile.展开更多
An orthogoual experimental scheme was designed for optimizing a water-cooled structure of the divertor plate. There were three influencing factors： the radius R of the water- cooled pipe, and the pipe spacing L1 and ...An orthogoual experimental scheme was designed for optimizing a water-cooled structure of the divertor plate. There were three influencing factors： the radius R of the water- cooled pipe, and the pipe spacing L1 and L3. The influence rule of different factors on the cooling effect and thermal stress of the plate were studied, for which the influence rank was respectively R 〉 L1 〉 L3 and L3 〉 R 〉 L1. The highest temperature value decreased when R and L1 increased~ and the maximum thermal stress value dropped when R, L1 and L3 increased. The final optimized results can be summarized as： R equals 6 mm or 7 mm, L1 equals 19 mm, and L3 equals 20 mm. Compared with the initial design, the highest temperature value had a small decline~ and the maximum thermal stress value dropped by 19~ to 24~. So it was not ideal to improve the cooling effect by optimizing the geometry sizes of the water-cooled structure, even worse than increasing the flow speed, but it was very effective for dropping the maximum thermal stress value. The orthogoaal experimental method reduces the number of experiments by 80%, and thus it is feasible and effective to optimize the water-cooled structure of the divertor plate with the orthogonal theory.展开更多
In the initial phase of the physics experiment, the double-null divertor plates used consist of graphite armor tiles, Mo-alloy intermediate layers and Cu-alloy coolant tubes. In the later operating phase, tungsten wil...In the initial phase of the physics experiment, the double-null divertor plates used consist of graphite armor tiles, Mo-alloy intermediate layers and Cu-alloy coolant tubes. In the later operating phase, tungsten will be used as armor tiles. A multi-physical field numerical analysis method is used in this paper. Its analysis model reflects more realistically the real divertor structure than other models. Two-dimensional （2D） and three-dimensional （3D） fluid flow field, temperature distribution and thermal stress analyses of the divertor plates are carried out by the ANSYS code. During the physics experimental phase with a heat flux of 1 MW/m2, a coolant velocity of 5.48 m/s, and a thermal stress of 750 kg/cm2, the graphite armor tiles successfully meet the requirements of temperature, thermal stress and sputtering erosion. The tungsten armor will be considered as a second candidate. The result of simulation can be used for upgrading the design parameters of the HL-2A poloidal divertor.展开更多
基金This work was supported by National Natural Science Foundation of China No.19889502.
文摘Thermal fatigue property of the divertor plate is one of the key issues that governs the lifetime of the divertor plate. Taking tungsten as surface material, a small-mock-up divertor plate was made by hot isostatic press welding (HIP). A thermal cycling experiment for divertor mock-up was carried out in the vacuum, where a high-heat-flux electronic gun was used as the thermal source. A cyclic heat flux of 9 MW/m2 was loaded onto the mock-up, a heating duration of 20 s was selected, the cooling water flow rate was 80 ml/s. After 1000 cycles, the surface and the W/Cu joint of the mock-up did not show any damage. The SEM was used to analyze the microstructure of the welding joint, where no cracks were found also.
基金supported by the National Natural Science Foundation of China(Nos.51505120 and 11105028)the National Magnetic Confinement Fusion Science Program of China(No.2015GB102004)
文摘During the discharging of Tokamak devices, interactions between the core plasma and plasma-facing components (PFCs) may cause exorbitant heat deposition in the latter. This poses a grave threat to the lifetimes of PFCs materials. An infrared (IR) diagnostic system consisting of an IR camera and an endoscope was installed on an Experimental Advanced Superconducting Tokamak (EAST) to monitor the surface temperature of the lower divertor target plate (LDTP) and to calculate the corresponding heat flux based on its surface temperature and physical structure, via the finite element method. First, the temperature obtained by the IR camera was calibrated against the temperature measured by the built-in thermocouple of EAST under baking conditions to determine the true temperature of the LDTP. Next, based on the finite element method, a target plate model was built and a discretization of the modeling domain was carried out. Then, a heat conduction equation and boundary conditions were determined. Finally, the heat flux was calculated. The new numerical tool provided results similar to those for DFLUX;this is important for future work on related physical processes and heat flux control.
基金Project supported by the National Natural Science Foundation of China (Grant No. 10805016)the National Magnetic Confinement Fusion Science Program,China (Grant No. 2009GB104008).
文摘A three-dimensional analysis model based on the finite element method （FEM） is developed, which can derive the evolution and distribution characteristics of heat flux deposited on the divertor plate from the surface temperature measured by infrared thermography diagnostics. The numerical simulations of surface heating due to localized power bursts and the power deposition calculations demonstrate that this analysis can provide accurate results and useful information about localized hot spots compared with the normal one- and two-dimensional calculations. In this paper, the details of this three- dimensional analysis are presented, and some results in ohmic heating and electron cyclotron resonant heating （ECRH） discharge on HL-2A are given.
基金Project supported by the Scientific Research Foundation of Liaoning Province,China(Grant No.2016J027)the Open Research Project of Key Laboratory of Materials Modification by Laser,Ion and Electron Beams,Ministry of Education(Grant No.KF1705)the National Key Research and Development Program of China(Grant Nos.2017YFA0402500,2017YFE0300400,and 2017YFE0301200)
文摘The influence of the J×B force on the topographical modification of W targets during a type-I-like ELM in ITER has been studied numerically. A two-dimensional(2D) fluid dynamics model is employed by solving liquid hydrodynamic Navier-Stokes equation with the 2D heat conduction equation in addition to driving forces for surface topography, such as surface tension and pressure gradient, the J×B force is particularly addressed. The governing equations are solved with the finite volume method by adequate prediction of the moving solid-liquid interface. Numerical simulations are carried out for a range of type-I ELM characteristic parameters. Our results indicate that both the surface tension and the J×B force contributes to the melt motion of tungsten plates when the energy flux is under 3000 MW·m^(-2), the surface tension is a major driving force while the pressure gradient is negligible. Our results also indicate that the J×B force makes the small hills grow at different rates at both the crater edges under a type-I-like ELM heat load with a Gaussian power density profile.
基金supported by National Basic Research Program of China(973 Program)(No.2013GB102000)
文摘An orthogoual experimental scheme was designed for optimizing a water-cooled structure of the divertor plate. There were three influencing factors： the radius R of the water- cooled pipe, and the pipe spacing L1 and L3. The influence rule of different factors on the cooling effect and thermal stress of the plate were studied, for which the influence rank was respectively R 〉 L1 〉 L3 and L3 〉 R 〉 L1. The highest temperature value decreased when R and L1 increased~ and the maximum thermal stress value dropped when R, L1 and L3 increased. The final optimized results can be summarized as： R equals 6 mm or 7 mm, L1 equals 19 mm, and L3 equals 20 mm. Compared with the initial design, the highest temperature value had a small decline~ and the maximum thermal stress value dropped by 19~ to 24~. So it was not ideal to improve the cooling effect by optimizing the geometry sizes of the water-cooled structure, even worse than increasing the flow speed, but it was very effective for dropping the maximum thermal stress value. The orthogoaal experimental method reduces the number of experiments by 80%, and thus it is feasible and effective to optimize the water-cooled structure of the divertor plate with the orthogonal theory.
文摘In the initial phase of the physics experiment, the double-null divertor plates used consist of graphite armor tiles, Mo-alloy intermediate layers and Cu-alloy coolant tubes. In the later operating phase, tungsten will be used as armor tiles. A multi-physical field numerical analysis method is used in this paper. Its analysis model reflects more realistically the real divertor structure than other models. Two-dimensional （2D） and three-dimensional （3D） fluid flow field, temperature distribution and thermal stress analyses of the divertor plates are carried out by the ANSYS code. During the physics experimental phase with a heat flux of 1 MW/m2, a coolant velocity of 5.48 m/s, and a thermal stress of 750 kg/cm2, the graphite armor tiles successfully meet the requirements of temperature, thermal stress and sputtering erosion. The tungsten armor will be considered as a second candidate. The result of simulation can be used for upgrading the design parameters of the HL-2A poloidal divertor.
