Aluminum foam is widely used in diverse areas to minimize the weight and maximize the absorption of shock energy in lightweight structures and various bio-materials.It presents a number of advantages,such as low densi...Aluminum foam is widely used in diverse areas to minimize the weight and maximize the absorption of shock energy in lightweight structures and various bio-materials.It presents a number of advantages,such as low density,incombustibility,non-rigidity,excellent energy absorptivity,sound absorptivity and low heat conductivity.The aluminum foam with an air cell structure was placed under the TDCB Mode II tensile load by using Landmark equipment manufactured by MTS to examine the shear failure behavior.The angle of the tapered adhesively-bonded surfaces of specimens was designated as a variable,and three models were developed with the inclined angles differing from one another at 6°,8° and 10°.The specimens with the inclined angles of 6°,8° and 10° have the maximum reaction forces of 168 N,194 N when the forced displacements are 6,5 and 4.2 mm respectively.There are three specimens with the inclined angles of 10°,8° and 6° in the order of maximum reaction force.As the analysis result,the maximum equivalent stresses of 0.813 MPa and 0.895 MPa happened when the forced displacements of 6 mm and 5 mm proceeded at the models of 6° and 8°,respectively.A simulation was carried out on the basis of finite element method and the experimental design.The results of the experiment and the simulation analysis are shown not different from each other significantly.Thus,only a simulation could be confirmed to be performed in substitution of an experiment,which is costly and time-consuming in order to determine the shearing properties of materials made of aluminum foam with artificial data.展开更多
Double cantilever beam （DCB） specimens were used to research the stress corrosion cracking of T225NG titanium alloy in loop water of high temperature and high pressure. DCB specimens were forced pre-stress, put into...Double cantilever beam （DCB） specimens were used to research the stress corrosion cracking of T225NG titanium alloy in loop water of high temperature and high pressure. DCB specimens were forced pre-stress, put into high pressure ataoclave , and the stress corrosion and crack expansion of specimens were observed and measured in 500 h, 1 000 h and 2000 h respectively. The results show that small expansion occurred along the direction of pre-cracking. According to calculation, the speed of cracking expansion is lower than 10 -9 m/s in 500 h and the value of K ISCC /KI is higher than 0. 75, which proves that T225NG has an excellent corrosion resistance in loop water. The main reason is that there is an oxide film on the surface of specimens. According to the analysis of energy dispersive spectroscopy （EDS） and X-ray diffraction （ XRD ） , the oxide film consists of TiO2. Therefore, the oxide film at the crack tip impedes the hydrogen separating out from the cathode to penetrate into titanium alloy and resists hydrogen embrittlement.展开更多
基金Project(2011-0006548)supported by Basic Science Research Program through the National Research Foundation of Korea
文摘Aluminum foam is widely used in diverse areas to minimize the weight and maximize the absorption of shock energy in lightweight structures and various bio-materials.It presents a number of advantages,such as low density,incombustibility,non-rigidity,excellent energy absorptivity,sound absorptivity and low heat conductivity.The aluminum foam with an air cell structure was placed under the TDCB Mode II tensile load by using Landmark equipment manufactured by MTS to examine the shear failure behavior.The angle of the tapered adhesively-bonded surfaces of specimens was designated as a variable,and three models were developed with the inclined angles differing from one another at 6°,8° and 10°.The specimens with the inclined angles of 6°,8° and 10° have the maximum reaction forces of 168 N,194 N when the forced displacements are 6,5 and 4.2 mm respectively.There are three specimens with the inclined angles of 10°,8° and 6° in the order of maximum reaction force.As the analysis result,the maximum equivalent stresses of 0.813 MPa and 0.895 MPa happened when the forced displacements of 6 mm and 5 mm proceeded at the models of 6° and 8°,respectively.A simulation was carried out on the basis of finite element method and the experimental design.The results of the experiment and the simulation analysis are shown not different from each other significantly.Thus,only a simulation could be confirmed to be performed in substitution of an experiment,which is costly and time-consuming in order to determine the shearing properties of materials made of aluminum foam with artificial data.
文摘Double cantilever beam （DCB） specimens were used to research the stress corrosion cracking of T225NG titanium alloy in loop water of high temperature and high pressure. DCB specimens were forced pre-stress, put into high pressure ataoclave , and the stress corrosion and crack expansion of specimens were observed and measured in 500 h, 1 000 h and 2000 h respectively. The results show that small expansion occurred along the direction of pre-cracking. According to calculation, the speed of cracking expansion is lower than 10 -9 m/s in 500 h and the value of K ISCC /KI is higher than 0. 75, which proves that T225NG has an excellent corrosion resistance in loop water. The main reason is that there is an oxide film on the surface of specimens. According to the analysis of energy dispersive spectroscopy （EDS） and X-ray diffraction （ XRD ） , the oxide film consists of TiO2. Therefore, the oxide film at the crack tip impedes the hydrogen separating out from the cathode to penetrate into titanium alloy and resists hydrogen embrittlement.
