Generation of double pulses at the Shanghai soft X-ray free electron laser facility

In this article, we present the promise of a new method generating double electron pulses in picosecondscale pulse length and tunable interpulse spacing at several picoseconds. This has witnessed an impressive potential of application in pump–probe techniques, two-color X-ray free electron laser, high-gradient witness bunch acceleration in a plasma, etc. Three-dimensional simulations are carried out to analyze the dynamic of the electron beam in a linear accelerator. Comparisons are made between the new method and existing ways.

Analysis of Enhanced Laser-Induced Breakdown Spectroscopy with Double Femtosecond Laser Pulses

In this paper, an experimental study of collinear geometry double-pulse femtosecond LIBS was performed on a Ni sample in ambient air in an effort to clarify the contributing processes responsible for the signal enhancement observed in comparison with the single-pulse case. Doublepulse LIBS spectra show a very clear enhancement when an optimum inter-pulse delay was used. The influences of the inter-pulse delay between two pulses on the LIBS signal intensity, electron temperature and density were investigated. It is most remarkable that the evolutions of signal enhancement and electron temperature versus the inter-pulse delay showed the same behavior and revealed two main regimes of interaction. These results provide additional insight into the possible emission enhancement mechanisms in the double pulse configuration.

Electron correlations in nonsequential double ionization of argon atoms by elliptically polarized laser pulses

Using a classical ensemble model, we investigate the correlation behaviour of electrons originating from nonsequential double ionization （NSDI） of argon atoms by the elliptically polarized laser pulses. Because of the ellipticity, not only the first electron to return but also the later return of tunneled electrons contribute significantly to NSDI. We mainly discuss two kinds of events of NSDI originating from the first and the second return separately. For the NSDI resulting from the recollision of the first return, the correlated electron momentum spectrum along the long axis of the laser polarization plane reveals an obvious V-like shape, located at the first and third quadrant. However, for the NSDI resulting from the recollision of the second return, the momenta of two electrons are distributed in the four quadrants uniformly. By analysing the trajectories of these two kinds, we find that the recollision energy and the laser phase at recollision are different for the first and second returning trajectories, which are responsible for the difference in the correlated behavior of the final electron momentum.

Micro-impulse and plasma plume produced by irradiating aluminum target with nanosecond laser pulses in double-pulse scheme

The micro-impulse generated by ablating an aluminum target in double-pulse laser bursts with different interpulse delays was investigated using a torsion pendulum.The plasma plume was simultaneously visualized using high-speed photography to analyze the coupling mechanism of the ablation impulse.The experiment was carried out using a pulsed laser with a pulse width of 8 ns and a wavelength of 1064 nm.The experimental results show that an impulse with an interpulse delay of 60 ns is roughly 60%higher than that with no delay between the two pulses,when the energy of both laser pulses is 50 m J.Therefore,double-pulse schemes could enhance the ablation impulse under certain conditions.This is because the ablation of the first laser pulse changes the optical properties of the aluminum target surface,increasing the absorptivity.However,the ablation impulse is reduced with a time delay of 20 ns when the energy of both laser pulses is100 mJ or 150 mJ.It can be concluded that the plasma produced by ablating the aluminum with the first pulse shields the second laser pulse.To summarize,the experimental results show that different delay times in a double-pulse scheme have a significant effect on the ablation impulse.The study provides a reference for the optimization of the parameters when laser ablation propulsion with a double-pulse scheme is applied in the fields of space debris removal,laser ablation thrusters,and so on.

Generation and storage of double slow light pulses in a solid

We experimentally study the generation and storage of double slow light pulses in a pr^3＋：Y2SiO5 crystal. Under electromagnetically induced transparency, a single signal pulse is stored in the spin coherence of the crystal. By simultaneously switching on two control fields to recall the stored information, the spin coherence is converted into two slow light pulses with distinct frequencies. Furthermore, the storage and controlled retrieval of double slow light pulses are obtained by manipulating the control fields. This study of double slow light pulses may have practical applications in information processing and all-optical networks.

Clinical usefulness of transpapillary removal of common bile duct stones by frequency doubled double pulse Nd:YAG laser

AIM: To study the efficacy and the safety of laser lithotripsy without direct visual control by using a balloon catheter in patients with bile duct stones that could not be extracted by standard technique. METHODS: The seventeen patients (7 male and 10 female; mean age 67.8 years) with difficult common bile duct (CBD) stones were not amenable for conventional endoscopic maneuvers such as sphincterotomy and mechanical lithotripsy were included in this study. Laser wavelengths of 532 nm and 1064 nm as a double pulse were applied with pulse energy of 120 mJ. The laser fiber was advanced under fluoroscopic control through the ERCP balloon catheter. Laser lithotripsy was continued until the fragment size seemed to be less than 10 mm. Endoscopic extraction of the stones and fragments was performed with the use of the Dormia basket and balloon catheter. RESULTS: Bile duct clearance was achieved in 15 of 17 patients (88%). The mean number of treatment sessions was 1.7 ± 0.6. Endoscopic stone removal could not be achieved in 2 patients (7%). Adverse effects were noted in three patients (hemobilia, pancreatitis, and cholangitis). CONCLUSION: The Frequency Doubled Double Pulse Nd:YAG (FREDDY) laser may be an effective and safe technique in treatment of difficult bile duct stones.

Intelligent process expert database of double pulse MIG welding of AI-Si alloy

Based on double pulse welding process characteristics, expert database structure and work flow are designed. Further, multiple outstanding specifications of 1.0 ram-diameter wire are obtained through a large number of experiments. By making non-linear regression analysis on these groups of standards, the relationship between average welding current and other pulse parameters can be found out. Polynomial regression equation is set up for further realization of＂ parameter estimation function of the expert database. Finally, the preliminary developed expert database is tested. The result indicates that the unified adjusting and parameters estimation of the expert database leads to stable welding process and good weld appearance.

Linear Track Estimation Using Double Pulse Sources for Near-Field Underwater Moving Target

The double pulse sources （DPS） method is presented for linear track estimation in this work. In the field of noise identification of underwater moving target, the Doppler will distort the frequency and amplitude of the radiated noise. To eliminate this, the track estimation is necessary. In the DPS method, we first estimate bearings of two sinusoidal pulse sources installed in the moving target through baseline positioning method. Meanwhile, the emitted and recorded time of each pulse are also acquired. Then the linear track parameters will be achieved based on the geometry pattern with the help of double sources spacing. The simulated results confirm that the DPS improves the performance of the previous double source spacing method. The simulated experiments were carried out using a moving battery car to further evaluate its performance. When the target is 40-60m away, the experiment results show that biases of track azimuth and abeam distance of DPS are under 0.6° and 3.4m, respectively. And the average deviation of estimated velocity is around 0.25m/s.

Double-Pulse Remote Laser-Induced Breakdown Spectroscopy Analysis of Magnesium Alloys

A self-built double-pulse remote Laser-Induced Breakdown Spectroscopy system in a collinear configuration was used to?investigate?the magnesium?alloys. The enhancement of the intensity was observed, about 4.7 times compared with single pulse LIBS. The peak intensities of line Y II 366.4 nm and Zr I 468.7 nm were used in the calibration curves, and the correlation coefficients were 0.9998 and 0.9547 respectively.

Design and Simulation of Solid State Pulser with Fast Rise Time and Double-exponential Waveform

Voltage pulses with fast rise time can be obtained from Marx circuits based on avalanche transistors. In this research, the ZETEX avalanche transistors are used as the switches in a Marx circuit to generate stable voltage pulses with double-exponential waveform and fast rise time. By using these transistors, the circuit is able to generate higher pulsed voltage with fewer stages. A three stages and a ten stages Marx circuit, as well as their triggering circuits, are designed. The two Marx circuits are also tested by simulations based on the Pspice code and by experiments, results of which are consistent with each other. With the ten stages Marx circuit, we obtain positive and negative pulses with the rise time of about 1.5 ns, the amplitude above 1 100 V, and the pulse width below 5 ns. It is proved that the proposed Marx circuit equipped with avalanche transistors could be an effective kind of solid-state pulse generator.

Application of Stand-off Double-Pulse Laser-Induced Breakdown Spectroscopy in Elemental Analysis of Magnesium Alloy

In this study, a stand-off and collinear double pulse laser-induced breakdown spectroscopy （DP LIBS） system was designed, and the magnesium alloy samples at a distance of 2.5 m away from the LIBS system were measured. The effect of inter-pulse delay on spectra was studied, and the signal enhancement was observed compared to the single pulse LIBS （SP LIBS）. The morphology of the ablated crater on the sample indicated a higher efficiency of surface pretreatment in DP LIBS. The calibration curves of Ytterbium （Y） and Zirconium （Zr） were investigated. The square of the correlation coefficient of the calibration curve of element Y reached up to 0.9998.

Enhancement of optical emission generated from femtosecond double-pulse laser-induced glass plasma at different sample temperatures in air

In double-pulse laser-induced breakdown spectroscopy(DP-LIBS), the collinear femtosecond double-pulse laser configuration is experimentally investigated with different initial sample temperatures using a Ti:sapphire laser. The glass sample is ablated to produce the plasma spectroscopy. During the experiment, the detected spectral lines include two Na(I) lines(589.0 nm and 589.6 nm) and one Ca(I) line at the wavelength of 585.7 nm. The emission lines are measured at room temperature(22 ℃) and three higher initial sample temperatures(T_s?=?100 ℃, 200 ℃, and 250 ℃). The inter-pulse delay time ranges from-250 ps to 250 ps.The inter-pulse delay time and the sample temperature strongly influence the spectral intensity,and the spectral intensity can be significantly enhanced by increasing the sample temperature and selecting the optimized inter-pulse time. For the same inter-pulse time of 0 ps(single-pulse LIBS), the enhancement ratio is approximately 2.5 at T_s?=?200 ℃ compared with that obtained at T_s?=?22 ℃. For the same inter-pulse time of 150 ps, the enhancement ratio can be up to 4 at T_s?=?200 ℃ compared with that obtained at T_s?=?22 ℃. The combined enhancement effects of the different initial sample temperatures and the double-pulse configuration in femtosecond LIBS are much stronger than that of the different initial sample temperatures or the double-pulse configuration only.

Wavelength-dependence of double optical gating for attosecond pulse generation

Both polarization gating （PG） and double optical gating （DOG） are productive methods to generate single attosecond （as） pulses. In this paper, considering the ground-state depletion effect, we investigate the wavelength-dependence of the DOG method in order to optimize the generation of single attosecond pulses for the future application. By calculating the ionization probabilities of the leading edge of the pulse at different driving laser wavelengths, we obtain the upper limit of duration for the driving laser pulse for the DOG setup. We find that the upper limit duration increases with the increase of laser wavelength. We further describe the technical method of choosing and calculating the thickness values of optical components for the DOG setup.

Atomic Processes in Emission Characteristics of a Lithium Plasma Plume Formed by Double-Pulse Laser Ablation

High resolution spectral analysis of lithium plasma formed by single and double laser ablation has been undertaken to understand the plume-laser interaction, especially at the early stages of the plasma plume. In order to identify different atomic processes in evolving plasma, time resolved spectral emission studies at different inter-pulse delays have been performed for ionic and neutral lithium lines emitting from different levels. Along with the enhancement in emission intensity, a large line broadening and spectral shift, especially in the case of excited state transition Li I 610.3 nm have been observed in the presence of the second pulse. This broadening and shift gradually decrease with increasing time delay. Another interesting feature is the appearance of a multi-component structure in the ionic line at 548.4 nm and these components change conversely into a single structure at the later stages of the plasma. The multi-component structures are correlated with the presence of different velocity （temperature） distributions in non-LTE conditions. Atomic analyses by computing photon emissivity coefficients with an ADAS code have been used to identify the above processes.

Spatio-temporal evaluation of Zr plasma parameters in a single-beam-splitting double-pulse laser-induced plasma

The plasma shielding effect is one of the major weaknesses of laser-induced breakdown spectroscopy(LIBS)as it causes non-linearity in signal strength.Although LIBS is typically carried out in constant laser energy,this non-linearity causes a reduction in sensitivity.In this work,we systematically examine laser-induced plasma,formed by two different excitation source modes,i.e.single pulse(SP)-excitation and single-beam-splitting double-pulse(SBS-DP)-excitation over Zr-2.5%Nb alloy.The two most important plasma parameters influencing the emission line intensity,plasma temperature(Te)and electron density(Ne)were studied and compared for both modes of laser excitation.Comparison of the results conclusively demonstrates that due to the splitting of the laser energy in the SBS-DP mode,the plasma shielding effect is significantly reduced.The reduced plasma shielding translates to an increased laser–sample coupling under SBS-DP mode.Temporal imaging of the total intensity of the laser-induced plasma in both excitation modes was also studied.The study shows how the plasma shielding effect can be reduced to improve the analytical quality of the LIBS methodology.

Re-Heating Effect on the Enhancement of Plasma Emission Generated from Fe Under Femtosecond Double-Pulse Laser Irradiation

In this paper, we present a study on the effect of inter-pulse delay using femtosecond double-pulse laser-induced breakdown spectroscopy in a collinear geometry. The temporal evolution of spectral intensity is performed for the lines of Fe I 423.60 nm, Fe I 425.08 nm and Fe I 427.18 nm. It is found that, by selecting appropriate inter-pulse delay, the signal enhancement can be significantly increased compared with the single-pulse case. A three-fold enhancement in the current experiment is obtained. The plasma temperature and electron density are also investigated based on the theory of Boltzmann plot and Stark broadening. We attribute the main mechanism for emission enhancement to the plasma re-heating effect.

Numerical Study on the Two-Dimensional Temperature Fields of Titanium/Aluminum Double-Layer Target Irradiated by High-Intensity Pulsed Ion Beam

Interaction between high-intensity pulsed ion beam （HIPIB） and a double-layer target with titanium film on top of aluminum substrate was simulated. The two-dimensional nonlinear thermal conduction equations, with the deposited energy in the target taken as source term, were derived and solved by finite differential method. As a result, the two-dimensional spatial and temporal evolution profiles of temperature were obtained for a titanium/aluminum double-layer target irradiated by a pulse of HIPIB. The effects of ion beam current density on the phase state of the target materials near the film and substrate interface were analyzed. Both titanium and aluminum were melted near the interface after a shot when the ion beam current density fell in the range of 100 A/cm2 to 200 A/cm2.

Comparison of performance between bipolar and unipolar double-frequency sinusoidal pulse width modulation in a digitally controlled H-bridge inverter system

By deriving the discrete-time models of a digitally controlled H-bridge inverter system modulated by bipolar sinu- soidal pulse width modulation （BSPWM） and unipolar double-frequency sinusoidal pulse width modulation （UDFSPWM） respectively, the performances of the two modulation strategies are analyzed in detail. The circuit parameters, used in this paper, are fixed. When the systems, modulated by BSPWM and UDFSPWM, have the same switching frequency, the stabil- ity boundaries of the two systems are the same. However, when the equivalent switching frequencies of the two systems are the same, the BSPWM modulated system is more stable than the UDFSPWM modulated system. In addition, a convenient method of establishing the discrete-time model of piecewise smooth system is presented. Finally, the analytical results are confirmed by circuit simulations and experimental measurements.

Tungsten ion source under double-pulse laser ablation system

New tungsten ion source is produced by using single and double-pulse laser ablation system. Combined collinear Nd：YAG laser beams（266＋1064 nm） are optimized to focus on the sample in air. Optimization of the experimental parameters is achieved to enhance the signal-to-noise ratio of the emission spectra. The velocity distribution of the emitted plasma cloud is carefully measured. The influences of the potential difference between the bias electrodes, laser wavelength and intensity on the current signal are also studied. The results show that the increase in the tungsten ion velocity under the double-pulse lasers causes the output current signal to increase by about three folds. The electron density and temperature are calculated by using the Stark-broadened line profile of tungsten line and Boltzmann plot method of the upper energy levels, respectively. The signal intensity dependence of the tungsten ion angular distribution is also analyzed. The results indicate that the double-pulse laser ablation configuration is more potent technique for producing more metal ion source deposition, thin film formation, and activated plasma-facing component material.

Effect of elliptical polarizations on nonsequential double ionization in two-color elliptically polarized laser fields

Using the classical ensemble model, we investigate the nonsequential double ionization（NSDI） of Ar and Mg in the two-color elliptically polarized laser pulse for different elliptical polarizations. Numerical results show that for Ar atoms the NSDI yield increases as the ellipticity increases, which is different from the case of Mg atoms. Moreover, the correlated behavior in the correlated electron momentum along the x direction and ion momentum distributions of Ar atoms are influenced by the ellipticity. By statistical analysis of different times, we can conclude that the ellipticity may be responsible for the NSDI processes. The correlated momenta distributions along the x direction at the recollision time are demonstrated and the results show that the travelling time and ellipticity can affect the emitted directions of both electrons.