Numerical simulation and control of welding distortion for double floor structure of high speed train

The welding heat source models and the plastic tension zone sizes of a typical weld joint involved in the double floor structure of high speed train under different welding parameters were calculated by a thermal-elastic-plastic FEM analysis based on SYSWELD code.Then,the welding distortion of floor structure was predicted using a linear elastic FEM and shrinkage method based on Weld Planner software.The effects of welding sequence,clamping configuration and reverse deformation on welding distortion of floor structure were examined numerically.The results indicate that the established elastic FEM model for floor structure is reliable for predicting the distribution of welding distortion in view of the good agreement between the calculated results and the measured distortion for real double floor structure.Compared with the welding sequence,the clamping configuration and the reverse deformation have a significant influence on the welding distortion of floor structure.In the case of30 mm reverse deformation,the maximum deformation can be reduced about 70%in comparison to an actual welding process.

Experiment and interface of Ti/Q235B cladding plate by double vertical explosive welding

The processing area is reduced by double vertical explosive welding and rolling. Those micro defects are avoided such as " fusion" and " jet pile" in the bonding zone of large Ti plate of explosive welding. So the quality and welding ratio of interface are improved. To solve the technical problem of narrow weldability window of Ti,a minimum critical detonation velocity explosive was invented to enlarge the window after double vertical explosive welding experiment and optimization. A comprehensive protective structure made up of rigid protective plates and flexible protective walls was designed to restrict the movement of cladding plates in double vertical explosive welding effectively and protect the cladding plates from damage. The interface microstructure showed that the bonding interfaces were periodically micro and small wavy and there are no micro defects such as melt metal and swirl.

Study on dynamic optimization of the double railway suspended vehicle for automatic transportation in the welding shop

The 2DOF dynamic equations of the doable railway suspended vehicle for automatic transportation in the welding shop are established. The sensitivities are analyzed. The parameter design is researched in ADAMS in terms of the inner railway radius, wheelbase, gauge, girder length of the doable railway suspended vehicle for automatic transportation in the welding product line. The mutual-restriction among the design variables is discussed and the selective ranges of the variables are confirmed. The result shows that the stability of the doable railway suspended vehicle for automatic transportation in the welding product line depends on parameters of the inner railway radius, wheelbase, gauge, girder length. The optimal results of the optimal objective and design variables have research significance for the virtual prototype of the doable suspension railway automation vehicle. The optimal results are input into the simulation model iteratively and the simulation results are fed back to the physical prototype. The veracity and reliability of peoformance forecast are improved so that the manufacture cost of the doable suspension railway automation vehicle is reduced significantly.

Intelligent process expert database of double pulse MIG welding of AI-Si alloy

Based on double pulse welding process characteristics, expert database structure and work flow are designed. Further, multiple outstanding specifications of 1.0 ram-diameter wire are obtained through a large number of experiments. By making non-linear regression analysis on these groups of standards, the relationship between average welding current and other pulse parameters can be found out. Polynomial regression equation is set up for further realization of＂ parameter estimation function of the expert database. Finally, the preliminary developed expert database is tested. The result indicates that the unified adjusting and parameters estimation of the expert database leads to stable welding process and good weld appearance.

Design and test of a protective structure for the double vertical explosive welding of large titanium/steel plate

A comprehensive protective structure with rigidity and flexibility was put forward and designed in view of the quality and safety problems for the double vertical explosive welding of large titanium/steel cladding plate.The movement speed and displacement of the protective structure was calculated by establishing its physics model.The dynamics and stabilization properties were analyzed,and the protective structure parameters were optimized and devised.The comprehensive protective structure,which is composed of rigidity unit and flexibility wall,can bear the impact of detonation wave and the high-speed movement of the cladding plate.There are no damage and deformation in the protective structure and the cladding plate.The protective structure can be used many times.The bonding rate of the Ti/steel plate obtained was nearly 100%,and there is no deformation,surface cracks,and big wave and micro-defects.Therefore,the protective problems of the double vertical explosive welding can be solved effectively by the protective structure.

Numerical simulation of dynamic thermal process during doublesided asymmetrical TIG backing welding of large thick plates

The dynamic thermal process during double-sided asymmetrical TIG backing welding of large thick plates （ 1 000 mm×700 mm×50 mm） is numerically simulated using MSC. MARC. The effect of arc distance on the thermal cycle in weld zone during double-sided asymmetrical T1G backing welding is investigated. The results show that the workpiece experiences double-peak thermal cycle in double-sided asymmetrical TIG backing welding. On the one hand, the fore arc has the pre- heating effect on the rear pass, and the pre-heating temperature depends on the distance between the double arcs, the heat input of fore arc, and the initial temperature of workpiece. On the other hand, the rear arc has the post-heating effect on the fore pass. The mutual effects of two heat sources decrease with the increase of arc distance.

Metal vapor behavior in double electrodes TIG welding

In present paper, the metal vapour behavior in double electrodes TIG welding was investigated by a numerical model, including the arc plasma and weld pool. The thermodynamic parameters and transport coefficients of the arc plasma were dependent on both the local temperature and the mass ratio of the metal vapour. A second viscosity approximation was used to formulate the diffusion coefficient of the metal vapour in the arc plasma. The temperature and flow fields together with the metal vapour concentration were simulated, and the influences of metal vapour on the arc plasma and the weld pool were analyzed. It was found that the metal vapour transport in the arc plasma was significantly influenced by the flow of the arc plasma, and the distribution of the metal vapour was more extended in the direction perpendicular to the line through the double electrodes tips. Both the arc plasma and the heat flux at the weld pool were constricted by the presence of the metal vapour, while the metal vapour had a minor effect on the total heat input to the work piece and the weld pool profile as a whole.

Double-sided gas tungsten arc welding process on TC4 titanium alloy

TC4 titanium alloy was welded by double-sided gas tungsten arc welding(GTAW) process in comparison with conventional GTAW process, the microstructure and mechanical performance of weld were also studied. The results indicate that double-sided GTAW is superior over regular single-sided GTAW on the aspects of increasing penetration, reducing welding deformation and improving welding efficiency. Good weld joint was obtained, which can reach 96.14% tensile strength and 70.85% elongation percentage of the base metal. The grains in heat-affected zone(HAZ) are thin and equiaxed and the degree of grain coarsening increases as one moves to the weld center line, and the interior of grains are α and α′ structures. The coarse columned and equiaxed grains, which interlace martensitic structures α′ and acicular α structures, are observed in weld zone. The fracture mode is ductile fracture.

Numerical Simulation of Current Density Distribution in Keyhole Double-Sided Arc Welding

In the double-sided arc welding system (DSAW) composing of PAW+TIG arcs, the PAW arc is guided by the TIG arc so that the current mostly flows through the direction of the workpiece thickness and the penetration is greatly improved. To analyze the current density distribution in DSAW is beneficial to understanding of this process. Considering all kinds of dynamic factors acting on the weldpool, this paper discusses firstly the surface deformation of the weldpool and the keyhole formation in PAW+TIG DSAW process on the basis of the magnetohydrodynamic theory and variation principles. Hence, a model of the current density distribution is developed. Through numerical simulation, the current density distribution in PAW+TIG DSAW process is quantitatively analyzed. It shows that the minimal radius of keyhole formed in PAW+TIG DSAW process is 0.5 mm and 89.5 percent of current flows through the keyhole.

Simulation analysis of double arc in plasma arc welding

Aimed at plasma arc welding, a mathematic model was established according to the theory of magnetic fluid dyaamics. The model was numerically analyzed by ANSYS software. The temperature, current density and plasma velocity distributions of normal arc had been simulated and compared with those of double arc. The results show that the appearance of double arc has made the temperature of the nozzle rise up to 5 000 K. The appearance of side arc could make the current density of the main arc decrease, and also make the maximal temperature of the arc reduce.

Study on heat efficiency of laser-TIG double-side welding

A series of laser-TIG double-side welding experiments for aluminum alloys were carried out to investigate the heat efficiency of the process. The melting efficiency was introduced to evaluate quantitatively the degree of the mutual effect of the laser and the arc. The results showed that the melting efficiency of laser-TIG double-side welding exceeded the sum of the laser and the arc taken separately. With the increase of heat input, the weld depth and melting efficiency of the laser and the arc were increased signifwantly. This, in fact, implies the strong mutual effect of the laser and the arc as heat sources joined simultaneously in the process. Comparatively, the higher efficiency of the laser constituent of heat sources plays the main role in the increase of the process efficiency. The phenomena of arc column convergence, increased laser absorptivity and the formation of heat accumulation region are the causes of the improvement of heat efficiency.

Self-Adaptive Control System for Additive Manufacturing Using Double Electrode Micro Plasma Arc Welding

Wire arc additive manufacturing(WAAM)has been investigated to deposit large-scale metal parts due to its high deposition efficiency and low material cost.However,in the process of automatically manufacturing the high-quality metal parts by WAAM,several problems about the heat build-up,the deposit-path optimization,and the stability of the process parameters need to be well addressed.To overcome these issues,a new WAAM method based on the double electrode micro plasma arc welding(DE-MPAW)was designed.The circuit principles of different metal-transfer models in the DE-MPAW deposition process were analyzed theoretically.The effects between the parameters,wire feed rate and torch stand-off distance,in the process of WAAM were investigated experimentally.In addition,a real-time DE-MPAW control system was developed to optimize and stabilize the deposition process by self-adaptively changing the wire feed rate and torch stand-off distance.Finally,a series of tests were performed to evaluate the control system’s performance.The results show that the capability against interferences in the process of WAAM has been enhanced by this self-adaptive adjustment system.Further,the deposition paths about the metal part’s layer heights in WAAM are simplified.Finally,the appearance of the WAAM-deposited metal layers is also improved with the use of the control system.

Finite Element Simulation of Thermal Field in Double Wire Welding

In this paper, the thermal field of double wire welding is simulated by using ANSYS software. Simulation results were shown that the total heat input (E) is the most significant parameters to change the value of t8/5;By the mean of rationally controlling the proportion of the front arc heat input (E1) in the total heat input (E) and appropriately selecting double wire spacing (L), It is effective means to get the double wire welding thermal cycle. By the way of simulation, it is possible to manage the thermal input in the double welding wires and to control the temperature field and cooling rate that are fundamental for the final joint quality, it is great importance guidance to optimize the double wire welding process parameters.

Effect of arc distance on temperature field and weld shape during double-sided arc welding

A new high efficiency welding method, double-sided double arc welding with double powers （DSAW-D）, is developed for thick plate of low alloy high strength steel in this study. It is well known that the thermal cycles have an important influence on the microstructure, shape, stress, distortion and mechanical property. The DSA W-D method can control the temperature field on a wide range by regulating the distance between two arcs, improve the microstructure and prevent hot and cold cracking of high strength steel. But at present, the effect of arc distance on the temperature field and shape is not clear. Therefore, the paper researches the effect of arc distance on the temperature field and weld pool during DSAW-D using finite element method. The transient temperature field of different arc distance in DSAW-D is calculated. To verify the numerical results, the temperature is measured by the thermo-couple and the calculated results agree approximately with experimental data. Farther, the thermal property and mutual effect of double-sided arcs are investigated. The temperature distributions and weld pool profile at different arc distances are obtained. The results show that arc distance is a very important factor to affect the heat process.

Microstructure of stainless steel weld in double-sided arc welding

Double-sided arc welding with a single power source can effectively increase the weld penetration, diminish distortion, improve welding speed and save energy. Compared to conventional arc welding processes, double-sided arc welding can generate a penetrating electromaguetic field to help to form fine dendritic microstrueture in the weld due to the symmetry of heating. Type 1Cr1SNi9Ti aastenitic stainless steel was bead-on-plate welded with double-sided arc welding and conventional plasma arc welding processes, respectively, and microstructure in the weld, heat-affected zone and base metal were examined. After analyzing the black carbon-enriched band in the weld during plasma arc welding with electron probe microanalyzer （ EPMA ） and X-ray diffraction （XRD） technology, it was found that the black band was shaped from the aggregation of ferrite in the fasion boundary. Hardness measurement showed that this black band does not apparently affect the microhardncss distribution in the weld.

Effect of laser parameters on arc behavior of laser-TIG double-side welding for aluminum alloy

The influence of laser parameters on are beharior of laser-TIC, dauble-side welding was investigated by utilizing CCD sensor and intage processing methods. It was found that are images had an obvious transformation from laser preheating to laser plasma ejected from the keyhole bottom, resulting in the phenomena of arc column convergence and arc root constrictian. The attraction phenomenon of the laser and the arc is also found in laser-TIG double-side welding. More noteworthy is that the behavior of arc attraction or constriction became much obvious at a lower current or laser plasma ejected from the keyhole bottom. The decrease in arc voltage had a certain relation u＇ith the improvement of arc stabilio.

Microstructures and hardness of flat-overhead weld of the high strength steel thick plate using double-sided arc welding

High strength steel thick plate is widely used in shipbuilding, pressure vessels, etc. , the balance between weld quality and welding efficiency is becoming a research focus. In this paper, double-sided double arc fiat-overhead welding experiments for high strength steel thick plate were conducted. Microstructures of weld have been observed through optical microscope （OM） and scanning electron microscope （SEM）. Transformation of microstructures under thermal cycles of multi peaks was analyzed. Macro and micro hardness were also tested. The results show that the heat-affected zone （HAZ） near the fusion line experiences thermal cycles up to three times. The microstructures there are the most complex, including coarse lath martensite in original coarse-grained zone, and net-like structure along grain boundaries in critical reheat coarse-grained zone. After several times of tempering for bucking welding, the features of acicula and lath are weakened. Its microstructure approaches to the microstructure of base metal which is tempering sorbite. The hardness test shows that the maximum hardness occurs at critical reheat coarse-grained zone, the hardness of reticulation structure at grain boundary can be up to 450 HV.

Effect of laser power on metal transfer in laser-double arcs P-MAG hybrid welding with single power source

The effect of laser power on metal transfer is studied under conditions of alternating combustion of double arcs in order to develop the welding process of the laser-double arcs pulsed metal active gas （P-MAG） hybrid welding with single power. Different laser power corresponds to different interactive mechanisms of laser and arc and to different methods of metal transfer in the hybrid welding. When the laser power ascends from 500 W to 1 500 W, the methods of metal transfer change from the complex transfer of one droplet per pulse, one droplet two pulses and one droplet much more pulses during the mixture of globular and projected transfer of the lead wire, and from one droplet two pulses and one droplet three pulses during globular transfer of the follow wire to the methods of the metal transfer of both lead wire and follow wire are stable one droplet two pulses and one droplet three pulses when the metal transfer is mainly globular. The arc sharps and pressure of droplet are altered with the laser power changing. The compression of the arcs is strengthened by the laser and the offset of the center of droplet mass is much more obvious with the increasing of the laser power.

Inclusion behavior and microstructure of weld metal with Ce in twin wire high heat input submerged-arc welding

In this study,the welding thermal cycle curve exhibited two temperature peaks in high heat-input twin-wire separate-pool submerged-arc welding and coarse-grained heat affected zone existed in the welded joint. The inclusions of primary weld metal and coarse-grained heat affected zone of Ce-added SAW should be Al_2O_3,MnO,SiO_2,TiO,Ce_2S_3,CeS,Ce_2O_2S and Ce_2O_3. Under the effect of welding thermal cycle,oxy-sulfides inclusions of Ce,the diameter of which was less than 2. 0 μm,slightly grew larger,but the composition and type of the inclusions didn't change. The microstructure of the large heat input weld metal had acicular ferrite that Ce oxide sulphide particles induced nucleation and proeutectoid ferrite. In the coarse-grained heat affected zone of weld metal,home-position precipitation of acicular ferrite and sympathetic acicular ferrite were both observed. It was supposed that previous crystal cells of acicular ferrite in austenite grain promoted home-position precipitation of acicular ferrite. Meanwhile,sympathetic acicular ferrite tended to nucleate at the primary acicular ferrite grain boundaries,where high dislocation density was located,and grew inside the neighboring carbon-depleted austenitic regions. The granular bainite nucleated in the austenitic zone with high carbon content close to acicular ferrite and sympathetic acicular ferrite.

Joint performance of laser-TIG double-side welded 5A06 aluminum alloy

The influence of welding parameters on mechanical properties and microstructure of the welds of laser-TIG double-side welded 5A06 aluminum alloy was investigated. The results show that the weld cross-sectional shape has an intimate relation with the mechanical properties and microstructure of the welds. The symmetrical "X" cross-section possesses a relatively higher tensile strength and elongation than the others, about 91% and 58% of those of base metal, respectively. The good weld profiles and free defects are responsible for the improvement of tensile properties. Due to low hardness of the fusion zone, this region is the weakest area in the tensile test and much easier to fracture. The loss of Mg element is responsible for the decrease of mechanical properties of the joints. The microstructure of "X" cross-section has an obvious difference along the direction of weld depth, and that of the "H" cross-section is consistent and coarse.