In order to address typical problems due to the huge demand of oil for consumption in traditional internal combustion engines,a new more efficient combustion mode is proposed and studied in the framework of Computatio...In order to address typical problems due to the huge demand of oil for consumption in traditional internal combustion engines,a new more efficient combustion mode is proposed and studied in the framework of Computational Fluid Dynamics(CFD).Moreover,a Non-dominated Sorting Genetic Algorithm(NSGA-Ⅱ)is applied to optimize the related parameters,namely,the engine methanol ratio,the fuel injection time,the initial temperature,the Exhaust Gas Re-Circulation(EGR)rate,and the initial pressure.The so-called Conventional Diesel Combustion(CDC),Homogeneous Charge Compression Ignition(HCCI)and the Reactivity Controlled Compression Ignition(RCCI)combustion modes are compared.The results show that RCCI has a higher methanol ratio and an earlier injection timing with moderate EGR rate and higher initial pressure.The initial temperature increases as the methanol ratio increases.In comparison,CDC has the lowest hydrocarbon and CO emissions and the highest combustion efficiency.At different crankshaft rotation angles corresponding to 50%of the combustion amount(CA50),the combustion temperature and boundary layer temperature of HCCI change significantly,while those of RCCI undergo limited variations.At the same CA50,the exergy losses of HCCI and RCCI are lower than that of the CDC.On the basis of these findings,it can be concluded that the methanol/diesel RCCI engine can be used to obtain a clean and efficient combustion process,which should be regarded as a promising combustion mode.展开更多
Research on dual-fuel(DF)engines has become increasingly important as engine manufacturers seek to reduce carbon dioxide emissions.There are significant advantages of using diesel pilot-ignited natural gas engines as ...Research on dual-fuel(DF)engines has become increasingly important as engine manufacturers seek to reduce carbon dioxide emissions.There are significant advantages of using diesel pilot-ignited natural gas engines as DF engines.However,different combustion modes exist due to variations in the formation of the mixture.This research used a simulation model and numerical simulations to explore the combustion characteristics of high-pressure direct injection(HPDI),partially premixed compression ignition(PPCI),and double pilot injection premixed compression ignition(DPPCI)combustion modes under a low-medium load.The results revealed that the DPPCI combustion mode provides higher gross indicated thermal efficiency and more acceptable total hydrocarbon(THC)emission levels than the other modes.Due to its relatively good performance,an experimental study was conducted on the DPPCI mode engine to evaluate the impact of the diesel dual-injection strategy on the combustion process.In the DPPCI mode,a delay in the second pilot ignition injection time increased THC emissions(a maximum value of 4.27g/(kW·h)),decreased the emission of nitrogen oxides(a maximum value of 7.64 g/(kW·h)),increased and then subsequently decreased the gross indicated thermal efficiency values,which reached 50.4%under low-medium loads.展开更多
Supersonic combustion of aviation kerosene is investigated under the flight conditions of Mach number 5 and fuel-air equivalence ratio 0.551.The trajectories of the fuel droplets and the heat/mass transfer between the...Supersonic combustion of aviation kerosene is investigated under the flight conditions of Mach number 5 and fuel-air equivalence ratio 0.551.The trajectories of the fuel droplets and the heat/mass transfer between them are simulated by means of discrete phase model(DPM).The k-ω model is chosen for turbulence closure and the non-premixed probability density function(PDF)approach is used to calculate the turbulence-chemistry interaction.The calculated wall static pressure and the total pressure loss coefficient are very close to the experiment results.The strut and cavity devices significantly increase the combustion efficiency.展开更多
The occurrence modes of alkali and alkaline-earth metals（AAEMs） in coal relate to their release behavior and ash formation during combustion. To better understand the transformation of AAEMs,the release behavior of ...The occurrence modes of alkali and alkaline-earth metals（AAEMs） in coal relate to their release behavior and ash formation during combustion. To better understand the transformation of AAEMs,the release behavior of water-soluble,HCl-soluble,HCl-insoluble AAEMs during Shenmu coal（SM coal） oxy-fuel combustion in the presence of SO2 and H2O in a drop-tube reactor was investigated through serial dissolution using H2O and HCl solutions. The results show that the release rates of AAEMs increase with an increase in temperature under the three atmospheres studied. The high release rates of Mg and Ca from SM coal are dependent on the high content of soluble Mg and Ca in SM coal. SO2 inhibits the release rates of AAEMs,while H2O promotes them. The effects of SO2 and H2O on the Na and K species are more evident than those on Mg and Ca species. All three types of AAEMs in coal can volatilize in the gas phase during coal combustion. The W-type AAEMs release excessively,whereas the release rates of I-type AAEMs are relatively lower. Different types of AAEM may interconvert through different pathways under certain conditions. Both SO2 and H2O promote the transformation reactions. The effect of SO2 was related to sulfate formation and the promotion by H2O occurs because of a decrease in the melting point of the solid as well as the reaction of H2O.展开更多
Existing droplet evaporation/combustion mod- els in computational fluid dynamics （CFD） simulation of spray combustion are based on simplified 1-D models. Both these models and recently developed 3-D models of single...Existing droplet evaporation/combustion mod- els in computational fluid dynamics （CFD） simulation of spray combustion are based on simplified 1-D models. Both these models and recently developed 3-D models of single- droplet combustion do not give the conditions for the different existing droplet combustion modes. In this paper, droplet evaporation and combustion are studied both analytically and numerically. In the analytical solution, a 2-D axisymmetric flow surrounding an evaporating and combusting droplet was considered. The governing equations were solved using an integral method, similar to the Karman-Pohlhausen method for solving boundary-layer flows with pressure gradient. The results give a local evaporation rate and flame radius in agree- ment with experimental results. In numerical simulation, 3-D combusting gas flows surrounding an ethanol droplet were studied. The prediction results show three modes of droplet combustion under different relative velocities, explaining the change in the evaporation constant with an increase in relative velocity observed in experiments. This implies that different droplet combustion models should be developed in simu- lating spray combustion. The predicted local evaporation rate and flame radius by numerical simulation are in agree- ment with the analytical solution in the range of azimuthal angles 0° 〈 θ 〈 90°. The numerical results indicate that the drag force of an evaporating and combusting droplet is much smaller than that of a cold solid particle, and thus the currently used drag models should be modified.展开更多
Four different pulverized coals have been used to study the effects of oxygen concentration on combustion characteristics under different enriched-oxygen conditions by entrained flow reactor experiments. The results s...Four different pulverized coals have been used to study the effects of oxygen concentration on combustion characteristics under different enriched-oxygen conditions by entrained flow reactor experiments. The results show that: with the increase of oxygen concentration, the ignition temperature of four coals greatly decreases and the low volatile coals decrease faster; with the increase of oxygen concentration, the ignition mode of pulverized coal has an obviously transformation from homogeneous ignition to heterogeneous ignition, and the corresponding oxygen concentrations are about 40% and 50%-60% respectively for bituminous coal and lignite, and both about 30% for lean coal and anthracite; with the increase of oxygen concentration, the optimal pulverized coal concentrations of bituminous coal and lignite increase firstly and then decrease, but for lean coal and anthracite, the optimal pulverized coal concentrations decrease slowly with the increase of oxygen concentration.展开更多
Acetone Planar Lase-Induced Fluorescence(PLIF)and OH-PLIF were employed to capture the fuel distribution and OH distribution downstream for the supersonic combustor based on the alternating-wedge strut.The combustion ...Acetone Planar Lase-Induced Fluorescence(PLIF)and OH-PLIF were employed to capture the fuel distribution and OH distribution downstream for the supersonic combustor based on the alternating-wedge strut.The combustion establishment process and combustion mode in the combustor under different fuel injection methods and different equivalence ratios were analyzed.Combined with the kerosene-PLIF and OH-PLIF results in the cavity combustor,a comparative analysis was conducted to understand the combustion characteristics and combustion modes between the alternating-wedge strut-based combustor and the cavity-based combustor.The results show that the combustor is in weak combustion mode in the case of low equivalence ratio,and the combustor is in intensive combustion mode in the case of high equivalence ratio.The lower limit of the equivalence ratio of the combustor to maintain the intensive combustion mode varies based on different fuel injection methods.The OH distribution under reacting condition has a strong correlation with the fuel distribution under non-reacting condition.The OH fluorescence signal near the injector is weaker when the fuel distribution is more concentrated.The injector position located at the base of the strut rear has better mixing performance,enabling the combustor to be in intensive combustion mode at a lower equivalence ratio.The combustion reaction in the alternating-wedge strut-based combustor is not necessarily dominated by mass transfer due to the mixing enhancement and premixed zone downstream of strut,while the combustion reaction process in the cavity-based combustor is mainly influenced by mass transfer.展开更多
文摘In order to address typical problems due to the huge demand of oil for consumption in traditional internal combustion engines,a new more efficient combustion mode is proposed and studied in the framework of Computational Fluid Dynamics(CFD).Moreover,a Non-dominated Sorting Genetic Algorithm(NSGA-Ⅱ)is applied to optimize the related parameters,namely,the engine methanol ratio,the fuel injection time,the initial temperature,the Exhaust Gas Re-Circulation(EGR)rate,and the initial pressure.The so-called Conventional Diesel Combustion(CDC),Homogeneous Charge Compression Ignition(HCCI)and the Reactivity Controlled Compression Ignition(RCCI)combustion modes are compared.The results show that RCCI has a higher methanol ratio and an earlier injection timing with moderate EGR rate and higher initial pressure.The initial temperature increases as the methanol ratio increases.In comparison,CDC has the lowest hydrocarbon and CO emissions and the highest combustion efficiency.At different crankshaft rotation angles corresponding to 50%of the combustion amount(CA50),the combustion temperature and boundary layer temperature of HCCI change significantly,while those of RCCI undergo limited variations.At the same CA50,the exergy losses of HCCI and RCCI are lower than that of the CDC.On the basis of these findings,it can be concluded that the methanol/diesel RCCI engine can be used to obtain a clean and efficient combustion process,which should be regarded as a promising combustion mode.
基金Project(2017YFE0102800)supported by the National Key R&D Program of ChinaProject(19JCYBJC21200)supported by the Tianjin Natural Science Foundation,China。
文摘Research on dual-fuel(DF)engines has become increasingly important as engine manufacturers seek to reduce carbon dioxide emissions.There are significant advantages of using diesel pilot-ignited natural gas engines as DF engines.However,different combustion modes exist due to variations in the formation of the mixture.This research used a simulation model and numerical simulations to explore the combustion characteristics of high-pressure direct injection(HPDI),partially premixed compression ignition(PPCI),and double pilot injection premixed compression ignition(DPPCI)combustion modes under a low-medium load.The results revealed that the DPPCI combustion mode provides higher gross indicated thermal efficiency and more acceptable total hydrocarbon(THC)emission levels than the other modes.Due to its relatively good performance,an experimental study was conducted on the DPPCI mode engine to evaluate the impact of the diesel dual-injection strategy on the combustion process.In the DPPCI mode,a delay in the second pilot ignition injection time increased THC emissions(a maximum value of 4.27g/(kW·h)),decreased the emission of nitrogen oxides(a maximum value of 7.64 g/(kW·h)),increased and then subsequently decreased the gross indicated thermal efficiency values,which reached 50.4%under low-medium loads.
基金Sponsored by the National Natural Science Foundation of China(10702064)
文摘Supersonic combustion of aviation kerosene is investigated under the flight conditions of Mach number 5 and fuel-air equivalence ratio 0.551.The trajectories of the fuel droplets and the heat/mass transfer between them are simulated by means of discrete phase model(DPM).The k-ω model is chosen for turbulence closure and the non-premixed probability density function(PDF)approach is used to calculate the turbulence-chemistry interaction.The calculated wall static pressure and the total pressure loss coefficient are very close to the experiment results.The strut and cavity devices significantly increase the combustion efficiency.
基金support for this research from the Natural Science Foundation of China (U1261110)the Natural Science Foundation of Shanxi Province (20130110422)the Foundation of State Key Laboratory of Coal Combustion (FSKLCC-0914)
文摘The occurrence modes of alkali and alkaline-earth metals（AAEMs） in coal relate to their release behavior and ash formation during combustion. To better understand the transformation of AAEMs,the release behavior of water-soluble,HCl-soluble,HCl-insoluble AAEMs during Shenmu coal（SM coal） oxy-fuel combustion in the presence of SO2 and H2O in a drop-tube reactor was investigated through serial dissolution using H2O and HCl solutions. The results show that the release rates of AAEMs increase with an increase in temperature under the three atmospheres studied. The high release rates of Mg and Ca from SM coal are dependent on the high content of soluble Mg and Ca in SM coal. SO2 inhibits the release rates of AAEMs,while H2O promotes them. The effects of SO2 and H2O on the Na and K species are more evident than those on Mg and Ca species. All three types of AAEMs in coal can volatilize in the gas phase during coal combustion. The W-type AAEMs release excessively,whereas the release rates of I-type AAEMs are relatively lower. Different types of AAEM may interconvert through different pathways under certain conditions. Both SO2 and H2O promote the transformation reactions. The effect of SO2 was related to sulfate formation and the promotion by H2O occurs because of a decrease in the melting point of the solid as well as the reaction of H2O.
基金supported by the National Natural Science Foundation of China(Grants 51390493 and 51266008)
文摘Existing droplet evaporation/combustion mod- els in computational fluid dynamics （CFD） simulation of spray combustion are based on simplified 1-D models. Both these models and recently developed 3-D models of single- droplet combustion do not give the conditions for the different existing droplet combustion modes. In this paper, droplet evaporation and combustion are studied both analytically and numerically. In the analytical solution, a 2-D axisymmetric flow surrounding an evaporating and combusting droplet was considered. The governing equations were solved using an integral method, similar to the Karman-Pohlhausen method for solving boundary-layer flows with pressure gradient. The results give a local evaporation rate and flame radius in agree- ment with experimental results. In numerical simulation, 3-D combusting gas flows surrounding an ethanol droplet were studied. The prediction results show three modes of droplet combustion under different relative velocities, explaining the change in the evaporation constant with an increase in relative velocity observed in experiments. This implies that different droplet combustion models should be developed in simu- lating spray combustion. The predicted local evaporation rate and flame radius by numerical simulation are in agree- ment with the analytical solution in the range of azimuthal angles 0° 〈 θ 〈 90°. The numerical results indicate that the drag force of an evaporating and combusting droplet is much smaller than that of a cold solid particle, and thus the currently used drag models should be modified.
文摘Four different pulverized coals have been used to study the effects of oxygen concentration on combustion characteristics under different enriched-oxygen conditions by entrained flow reactor experiments. The results show that: with the increase of oxygen concentration, the ignition temperature of four coals greatly decreases and the low volatile coals decrease faster; with the increase of oxygen concentration, the ignition mode of pulverized coal has an obviously transformation from homogeneous ignition to heterogeneous ignition, and the corresponding oxygen concentrations are about 40% and 50%-60% respectively for bituminous coal and lignite, and both about 30% for lean coal and anthracite; with the increase of oxygen concentration, the optimal pulverized coal concentrations of bituminous coal and lignite increase firstly and then decrease, but for lean coal and anthracite, the optimal pulverized coal concentrations decrease slowly with the increase of oxygen concentration.
文摘Acetone Planar Lase-Induced Fluorescence(PLIF)and OH-PLIF were employed to capture the fuel distribution and OH distribution downstream for the supersonic combustor based on the alternating-wedge strut.The combustion establishment process and combustion mode in the combustor under different fuel injection methods and different equivalence ratios were analyzed.Combined with the kerosene-PLIF and OH-PLIF results in the cavity combustor,a comparative analysis was conducted to understand the combustion characteristics and combustion modes between the alternating-wedge strut-based combustor and the cavity-based combustor.The results show that the combustor is in weak combustion mode in the case of low equivalence ratio,and the combustor is in intensive combustion mode in the case of high equivalence ratio.The lower limit of the equivalence ratio of the combustor to maintain the intensive combustion mode varies based on different fuel injection methods.The OH distribution under reacting condition has a strong correlation with the fuel distribution under non-reacting condition.The OH fluorescence signal near the injector is weaker when the fuel distribution is more concentrated.The injector position located at the base of the strut rear has better mixing performance,enabling the combustor to be in intensive combustion mode at a lower equivalence ratio.The combustion reaction in the alternating-wedge strut-based combustor is not necessarily dominated by mass transfer due to the mixing enhancement and premixed zone downstream of strut,while the combustion reaction process in the cavity-based combustor is mainly influenced by mass transfer.
