Design of S-Band Circularly Polarized Double-Layer Microstrip Antenna

This paper proposes a compact polarization microstrip antenna based on double-layer structure.The bandwidth of the whole antenna is widened by expanding the top and bottom layers respectively.After the design of antenna structure and adjustment of size,the proposed antenna can achieve both the left-and right-hand circular polarizations in 2.33 GHz-2.97 GHz.Measurement results indicate that the effective bandwidth is 640 MHz in S-band and the relative bandwidth can achieve 24% with 11 S less than 15 dB.

Designing a Dual-Feed Circular Polarization Antenna

This paper describes a novel dual-feed circularly polarized antenna,and the dual feeding mode is realized by grooving on the antenna radiator.The antenna utilizes air dielectric material to meet the requirements of low weight and cost.Test results demonstrate that the antenna exhibits capacitive loading between the metal antenna patch and the ground floor,allowing for adjustment of the working frequency of the dual-feed circularly polarized microstrip antenna.Specifically,the original center frequency of 2.264 GHz was reduced to 1.582 GHz,facilitating antenna miniaturization and broad bandwidth.With a return loss(S11)below-10 dB,a bandwidth of 72 MHz(1.552-1.624 GHz)was obtained.Additionally,the dual-feed microstrip antenna incorporates a 90°bridge,resulting in circular polarization gains of 2.26 dBi at 1.561 GHz and 2.45 dBi at 1.575 GHz.Overall,the antenna design offers a large working bandwidth and excellent circular polarization characteristics,making it suitable for a wide range of applications in satellite navigation and positioning terminals.

Dual-Polarized Slot-Coupled Microstrip Antenna with Very High Isolation

A wideband dual-polarized slot-coupled stacked microstrip antenna with very high isolation and low cross-polarization is presented. To improve isolation between two poiarization ports, the stacked patches are excited by an open-ended and a T-shaped microstrip lines both via two H-shaped slots placed in a ＂T＂ configuration. The measured isolation is better than 40.5 dB over the bandwidth from 8.8 to 9.8 GHz with cross-polarization level less than - 28.5 dB. The measured VSWR ≤ 2 bandwidths reach 20.7 96 and 19.196 at the verrical and horizontal polarization ports, respectively. This antenna is suitable to be used as array elements in spacebome synthetic aperture radars （SAR） and active phased array radars.

Metamaterials and metasurfaces for designing metadevices:Perfect absorbers and microstrip patch antennas

In the past twenty years, electromagnetic metamaterials represented by left-handed metamaterials（LHMs） have attracted considerable attention due to the unique properties such as negative refraction, perfect lens, and electromagnetic cloaks. In this paper, we present a comprehensive review of our group＇s work on metamaterials and metasurfaces. We present several types of LHMs and chiral metamaterials. As a two-dimensional equivalent of bulk three-dimensional metamaterials, metasurfaces have led to a myriad of devices due to the advantages of lower profile, lower losses, and simpler to fabricate than bulk three-dimensional metamaterials. We demonstrate the novel microwave metadevices based on metamaterials and metasurfaces： perfect absorbers and microwave patch antennas, including novel transmission line antennas,high gain resonant cavity antennas, wide scanning phased array antennas, and circularly polarized antennas.

Wireless Strain Measurement Based on a Microstrip Patch Antenna

Wireless interrogation of a rectangular microstrip patch antenna for strain measurement is investigated by simulations.To analyze the antenna performance,a microstrip line-feeding patch antenna at 10 GHz is designed.A patch antenna wirelessly fed by a horn is proposed to measure the strain.The direction information of strain detected by the patch antenna is also considered.The strain can be detected both in the width and length directions.It is shown that the strain can be measured wirelessly using a standard horn antenna.This kind of wireless strain-sensing technique offers significant potential for wireless structural health monitoring(SHM),especially for high-end equipment.

Broadband printed antennas and dual-polarized microstrip and waveguide slot antenna arrays

In order to meet the urgent needs in wireless communications, microwave image synthetic aperture radars （SAR）, and electronic warfare systems, this dissertation studies several types of broadband dual-polarized planar antenna elements and arrays, and proposes a few of novel designs with experimental verification. The main accomplishments reported in the dissertation are as follows.

Design and Analysis of Microstrip Antenna Arrays in Composite Laminated Substrates

In high performance aerospace systems where weight and aerodynamics are of major concern, fiber reinforced composite laminates can be tailored to achieve desirable mechanical properties and accommodate low-profile microstrip antenna. This work aims at the analysis of microstrip antenna array embedded in composite laminated substrates. The size of a single antenna is first calculated by spectral domain analysis to model the effects of the substrate’s electromagnetic property and the orientation of the laminate layers. The antenna array as well as the feed network, composed of microstrip transmission lines, quarter wave-length impedance transformers, and T-junction power dividers, is then tuned to accommodate the effects of the coupling between the antenna elements and the feed network loss. The performance of the 1 × 2, 1 × 4, and 1 × 8 linear array and 2 × 2 and 2 × 4 planar array are shown to have better directivity when embedded in composite laminated substrate compared with those when attached on isotropic substrate. Both 1 × 2 and 1 × 4 arrays at 2.4 GHz are validated experimentally to achieve better coverage.

Compact wideband microstrip array antenna with beam squint

A compact wideband microstrip array antenna with a squint beam is introduced without the matched load. Its measured beam is at 10° offset to the broadside with a measured gain of 12 dB at 10 GHz. The measured impedance bandwidth （voltage standing wave ratio （VSWR）≤2） is over 16%, which agrees well with the simulated one. It is a low-cost wideband design with compact simple structure, suited for military and commercial application.

Rectangular Microstrip Antenna with Air Cavity for High Gain and Improved Front to Back Ratio

A rectangular microstrip patch antenna using conventional Poly Tetra Fluride Ethelene (PTFE) substrate with air cavity is proposed and theoretically investigated. Considerably high gain along with improved front to back radiation isolation is demonstrated using such proposed antenna. The radiation performance of this new antenna has been compared to a conventional microstrip patch for some commonly used aspect ratios (width to length ratio). Compared to conventional microstrip antenna the proposed configuration shows more than 12% increment in peak gain and more than 10% increment in front to back radiation performance in each set of aspect ratio. The elucidation of such improvement in the radiation characteristics of the proposed antenna is also presented.

Different Feeding Techniques of Microstrip Patch Antennas with Spiral Defected Ground Structure for Size Reduction and Ultra-Wide Band Operation

Different feeding techniques of microstrip patch antennas with different spiral defected ground structures are presented in this paper. The investigated structures illustrate some merits in designing multi-electromagnetic band-gap structures by adjusting the capacitance and changing the inductance through varying the width and length of spiral defected ground structure. Then by applying the three different spirals shapes (one, two and four arms) as the ground plane of microstrip patch antenna with different feeding techniques to create multi or ultra wide-band, improve the antenna gain and reduce the antenna size, it is found that the four arms spiral defected ground structure of microstrip patch antenna with offset feed gives good performance, electrical size reduction to about 75% as compared to the original patch size and ultra-wide bandwidth extends from 2 GHz up to 12 GHz with ?8 dB impedance bandwidth.

Strain-Insensitive Hierarchically Structured Stretchable Microstrip Antennas for Robust Wireless Communication

As the key component of wireless data transmission and powering,stretchable antennas play an indispensable role in flexible/stretchable electronics.However,they often suffer from frequency detuning upon mechanical deformations;thus,their applications are limited to wireless sensing with wireless transmission capabilities remaining elusive.Here,a hierarchically structured stretchable microstrip antenna with meshed patterns arranged in an arched shape showcases tunable resonance frequency upon deformations with improved overall stretchability.The almost unchanged resonance frequency during deformations enables robust on-body wireless communication and RF energy harvesting,whereas the rapid changing resonance frequency with deformations allows for wireless sensing.The proposed stretchable microstrip antenna was demonstrated to communicate wirelessly with a transmitter(input power of−3 dBm)efficiently(i.e.,the receiving power higher than−100 dBm over a distance of 100 m)on human bodies even upon 25%stretching.The flexibility in structural engineering combined with the coupled mechanical-electromagnetic simulations,provides a versatile engineering toolkit to design stretchable microstrip antennas and other potential wireless devices for stretchable electronics.

Microstrip Antennas Loaded with Shorting Post

In this paper, a technical review with recent advances of the microstrip antennas loaded with shorting posts is presented. The overall size of the antenna is significantly reduced by a single shorting posts and the effect of the various parameters of shorting posts on short-circuit microstrip antenna is also discussed.

Effect of Partial Ground Plane Removal on the Radiation Characteristics of a Microstrip Antenna

This study presents a new, simple method for reducing the back-lobe radiation of a microstrip antenna (MSA) by a partially removed ground plane of the antenna. The effect of the partial ground plane removal in different configurations on the radiation characteristics of a MSA are investigated numerically. The partial ground plane removal reduces the backlobe radiation of the MSA by suppressing the surface wave diffraction from the edges of the antenna ground plane. For further improving the front-to-back (F/B) ratio of the MSA, a new soft-surface configuration consisting of an array of stand-up split ring resonators (SRRs) are placed on a bare dielectric substrate near the two ground plane edges. Compared to the F/B ratio of a conventional MSA with a full ground plane of the same size, an improved F/B ratio of 9.7 dB has been achieved experimentally for our proposed MSA.

A BROADBAND APERTURE-COUPLED STACKED MICROSTRIP ANTENNA WITH BOTH PATCHES NOTCHED AND OFFSET

This paper proposes a new approach to further improving the bandwidth of a typical aperture-coupled stacked microstrip antenna by cutting triangular notches in the radiating sides of both radiating patches together with offsetting both patches. An antenna applying this new approach is designed,fabricated,and tested. The experimental antenna could achieve a measured impedance bandwidth of about 37.5% for the Voltage Standing Wave Ratio(VSWR) ≤ 2in X-band.

Mutual coupling suppression of aperture coupled microstrip antenna array

本文提出了一种在金属板开4个半圆缝隙来抑制微带天线阵阵元之间耦合的方法.微带天线阵为4单元结构,天线为双层介质层.通过在圆形贴片45°方向开矩形缝隙来实现圆极化特性,利用孔径耦合馈电及反向馈电原理,保证相邻的2个单元均有90°相位差.在金属板上对称地开4个半圆形缝隙切断了单元间的耦合电流场,抑制了表面波,降低了单元间的耦合效应.仿真结果显示,当在接地板上对称地开4个半圆形缝隙后,微带天线阵的耦合系数明显降低,旁瓣与后瓣电平被有效地抑制,天线的增益增加.因此,这是一个十分有效的抑制微带天线阵阵元间耦合的方法.

Performance Optimization of Microstrip Antenna with Different Slot Configurations and Various Dielectric Materials

The probe-fed patch antennas were proposed by changing the parameters such as dielectric materials and dimensions of patch for detail investigation of changes in output characteristics. Four rectangular slots were introduced separately for optimizing the antenna design and characteristics. This study illustrated the changes of output characteristics of an antenna with respect to the number of introduced slots on the radiating patch in addition to the effect of various dielectric materials on antenna performances. The antenna performances were analyzed by plotting the observation of various dielectric materials. The changes of antenna characteristics were also observed by introducing four numbers of slots on each edge of the patch to improve radiation characteristics with a wider impedance bandwidth.

Corner Fed Microstrip Antenna Analysisfor Dual Polarization

This paper investigates a corner fed microstrip patch antenna by means of the cavity model with proposed feed modeling. The input impedance and radiation patterns for a corner feed are calculated. The mutual coupling between two corner feeds is investigated. An improvement in mutual coupling has been found for corner feeds relative to edge feeds, which is helpful for the design of dual polarized antenna arrays in wireless communication and radar applications.

Dual-Frequency Operation of Bow-Tie Microstrip Antenna

Characteristics of a single-feed dual-frequency bow-tie microstrip antenna are studied. By using the variation method, simple formulas for resonant frequencies of the bow-tie microstrip antenna are derived. It is shown that the dual-frequency ratio can be controlled easily by choosing the parameters of the antenna. This design gives compact antenna size and simple antenna structure. Experimental results are presented, verifying the validity of the design.

STUDY ON THE WIDE-BAND AND HIGH-GAIN MICROSTRIP ANTENNA ELEMENT

A novel three layers microstrip antenna element that has the advantages of wideband and high-gain is proposed. The eigenvalue equation and the frequency characteristic formulas of the input Voltage Stand Wave Ratio ( VSWR ) are obtained by using the spectral domain method and equivalent circuit method, respectively. With the aid of the numerical results, a C-band microstrip antenna element with bandwidth of 16% (VSWR【1.5) or 25% (VSWR【2) and gain of 10.2-11.3 dB is developed, which are much larger than the bandwidth of 5-6% and the gain of 6-7 dB of the common microstrip antenna element.

A NEW MODIFIED CIRCULAR MICROSTRIP ANTENNA

A new modified circular microstrip antenna with circular polarization is researched in this paper and a new method named for equivalent ellipse is proposed by authors to calculate the patterns, axial ratio and partial power gain. The theoretical results agree well with the experimental data.