This paper proposes a type of double-layer charge liner fabricated using chemical vapor deposition(CVD)that has tungsten as its inner liner.The feasibility of this design was evaluated through penetration tests.Double...This paper proposes a type of double-layer charge liner fabricated using chemical vapor deposition(CVD)that has tungsten as its inner liner.The feasibility of this design was evaluated through penetration tests.Double-layer charge liners were fabricated by using CVD to deposit tungsten layers on the inner surfaces of pure T2 copper liners.The microstructures of the tungsten layers were analyzed using a scanning electron microscope(SEM).The feasibility analysis was carried out by pulsed X-rays,slug-retrieval test and static penetration tests.The shaped charge jet forming and penetration law of inner tungsten-coated double-layer liner were studied by numerical simulation method.The results showed that the double-layer liners could form well-shaped jets.The errors between the X-ray test results and the numerical results were within 11.07%.A slug-retrieval test was found that the retrieved slug was similar to a numerically simulated slug.Compared with the traditional pure copper shaped charge jet,the penetration depth of the double-layer shaped charge liner increased by 11.4% and>10.8% respectively.In summary,the test results are good,and the numerical simulation is in good agreement with the test,which verified the feasibility of using the CVD method to fabricate double-layer charge liners with a high-density and high-strength refractory metal as the inner liner.展开更多
The time-sequenced damage behavior of the reactive projectile impacting double-layer plates is discussed.The analytical model considering the combined effect of kinetic and chemical energy is developed to reveal the d...The time-sequenced damage behavior of the reactive projectile impacting double-layer plates is discussed.The analytical model considering the combined effect of kinetic and chemical energy is developed to reveal the damage mechanism.The influences of impact velocity and reactive projectile chemical characteristics on the damage effect are decoupled analyzed based on this model.These analyses indicate that the high energy releasing efficiency and fast reaction propagation velocity of the reactive projectile are conducive to enhancing the damage effect.The experiments with various reactive projectiles impact velocity increasing from 702 to 1385 m/s were conducted to verify this model.The experimental results presented that,the damage hole radius of the rear-plate increases with the increase of impact velocity.At the impact velocity of 1350 m/s,the radius of damage hole formed by PTFE/Al/Bi_(2)O_(3),PTFE/Al/MoO_(3),PTFE/Al/Fe_(2)O_(3)projectile on the rear-plate become smaller in sequence.These results are consistent with the analytical model prediction,demonstrating that this model can predict the damage effect quantitatively.This work is of constructive significance to the application of reactive projectiles.展开更多
Gas-driven permeation(GDP)and plasma-driven permeation(PDP)of hydrogen gas through Ga In Sn/Fe are systematically investigated in this work.The permeation parameters of hydrogen through Ga In Sn/Fe,including diffusivi...Gas-driven permeation(GDP)and plasma-driven permeation(PDP)of hydrogen gas through Ga In Sn/Fe are systematically investigated in this work.The permeation parameters of hydrogen through Ga In Sn/Fe,including diffusivity,Sieverts'constant,permeability,and surface recombination coefficient are obtained.The permeation flux of hydrogen through Ga In Sn/Fe shows great dependence on external conditions such as temperature,hydrogen pressure,and thickness of liquid Ga In Sn.Furthermore,the hydrogen permeation behavior through Ga In Sn/Fe is well consistent with the multilayer permeation theory.In PDP and GDP experiments,hydrogen through Ga In Sn/Fe satisfies the diffusion-limited regime.In addition,the permeation flux of PDP is greater than that of GDP.The increase of hydrogen plasma density hardly causes the hydrogen PDP flux to change within the test scope of this work,which is due to the dissolution saturation.These findings provide guidance for a comprehensive and systematic understanding of hydrogen isotope recycling,permeation,and retention in plasma-facing components under actual conditions.展开更多
To develop the microwave absorbing(MA)properties of cementitious material mixed with mine solid waste,the iron tailings cementitious microwave absorbing materials were prepared.The iron tailings was treated into diffe...To develop the microwave absorbing(MA)properties of cementitious material mixed with mine solid waste,the iron tailings cementitious microwave absorbing materials were prepared.The iron tailings was treated into different particle sizes by planetary ball mill,and the physicochemical properties of iron tailings were tested by laser particle size analyzer and scanning electron microscope(SEM).The electromagnetic parameters of iron tailings cementitious materials were characterized by a vector network analyzer and simulated MA properties,and the MA properties of iron tailings-cement composite system with steel fiber as absorber was studied.Based on the design of the single-layer structure,optimum mix ratio and thickness configuration method of double-layer structure were further studied,meanwhile,the mechanical properties and engineering application were analyzed and discussed.The results show that the particle size of iron tailings can afiect its electromagnetic behavior in cementitious materials,and the smaller particles lead the increase of demagnetisation efiect induced by domain wall motion and achieve better microwave absorbing properties in cementitious materials.When the thickness of matching layer and absorbing layer is 5 mm,the optimized microwave absorbing properties of C1/C3 double-layer cementitious material can obtain optimal RL value of-27.61 dB and efiective absorbing bandwidth of 0.97 GHz,which attributes to the synergistic efiect of impedance matching and attenuation characteristics.The double-layer microwave absorbing materials obtain excellent absorbing properties and show great design flexibility and diversity,which can be used as a suitable candidate for the preparation of favorable microwave absorbing cementitious materials.展开更多
To reduce the comprehensive costs of the construction and operation of microgrids and to minimize the power fluctuations caused by randomness and intermittency in distributed generation,a double-layer optimizing confi...To reduce the comprehensive costs of the construction and operation of microgrids and to minimize the power fluctuations caused by randomness and intermittency in distributed generation,a double-layer optimizing configuration method of hybrid energy storage microgrid based on improved grey wolf optimization(IGWO)is proposed.Firstly,building a microgrid system containing a wind-solar power station and electric-hydrogen coupling hybrid energy storage system.Secondly,the minimum comprehensive cost of the construction and operation of the microgrid is taken as the outer objective function,and the minimum peak-to-valley of the microgrid’s daily output is taken as the inner objective function.By iterating through the outer and inner layers,the system improves operational stability while achieving economic configuration.Then,using the energy-self-smoothness of the microgrid as the evaluation index,a double-layer optimizing configuration method of the microgrid is constructed.Finally,to improve the disadvantages of grey wolf optimization(GWO),such as slow convergence in the later period and easy falling into local optima,by introducing the convergence factor nonlinear adjustment strategy and Cauchy mutation operator,an IGWO with excellent global performance is proposed.After testing with the typical test functions,the superiority of IGWO is verified.Next,using IGWO to solve the double-layer model.The case analysis shows that compared to GWO and particle swarm optimization(PSO),the IGWO reduced the comprehensive cost by 15.6%and 18.8%,respectively.Therefore,the proposed double-layer optimizationmethod of capacity configuration ofmicrogrid with wind-solar-hybrid energy storage based on IGWO could effectively improve the independence and stability of the microgrid and significantly reduce the comprehensive cost.展开更多
Traditional transgenic detection methods require high test conditions and struggle to be both sensitive and efficient.In this study,a one-tube dual recombinase polymerase amplification(RPA)reaction system for CP4-EPSP...Traditional transgenic detection methods require high test conditions and struggle to be both sensitive and efficient.In this study,a one-tube dual recombinase polymerase amplification(RPA)reaction system for CP4-EPSPS and Cry1Ab/Ac was proposed and combined with a lateral flow immunochromatographic assay,named“Dual-RPA-LFD”,to visualize the dual detection of genetically modified(GM)crops.In which,the herbicide tolerance gene CP4-EPSPS and the insect resistance gene Cry1Ab/Ac were selected as targets taking into account the current status of the most widespread application of insect resistance and herbicide tolerance traits and their stacked traits.Gradient diluted plasmids,transgenic standards,and actual samples were used as templates to conduct sensitivity,specificity,and practicality assays,respectively.The constructed method achieved the visual detection of plasmid at levels as low as 100 copies,demonstrating its high sensitivity.In addition,good applicability to transgenic samples was observed,with no cross-interference between two test lines and no influence from other genes.In conclusion,this strategy achieved the expected purpose of simultaneous detection of the two popular targets in GM crops within 20 min at 37°C in a rapid,equipmentfree field manner,providing a new alternative for rapid screening for transgenic assays in the field.展开更多
AIM:To report the outcomes of three cases of corneal perforation managed with simultaneous tectonic Descemet stripping endothelial keratoplasty(t-DSEK)and tectonic Bowman layer transplant(t-BLT)as an alternative to te...AIM:To report the outcomes of three cases of corneal perforation managed with simultaneous tectonic Descemet stripping endothelial keratoplasty(t-DSEK)and tectonic Bowman layer transplant(t-BLT)as an alternative to tectonic penetrating keratoplasty(t-PKP).METHODS:Three eyes of three patients receiving simultaneous t-DSEK and t-BLT for corneal perforation were included.The technique for DSEK was modified depending on individual requirements.The t-BLT technique was standardised using an 8 mm graft and fixated with a running suture.Success was measured by the ability of this procedure to close a corneal perforation.RESULTS:All three cases achieved tectonic eye globe restoration and remained stable during the minimum 3-month observation period.Reinterventions were relatively common:2 cases required amniotic membrane transplant for persistent epithelial defects.One case required DSEK rebubbling.One case developed angle closure glaucoma requiring surgical peripheral iridectomy.CONCLUSION:Simultaneous t-DSEK and t-BLT may be a useful strategy for the management of corneal perforation as an alternative management to t-PKP for selected cases.展开更多
The interfacial wettability and heat transfer behavior are crucial in the strip casting of high phosphorus-containing steel.A hightemperature simulation of strip casting was conducted using the droplet solidification ...The interfacial wettability and heat transfer behavior are crucial in the strip casting of high phosphorus-containing steel.A hightemperature simulation of strip casting was conducted using the droplet solidification technique with the aims to reveal the effects of phosphorus content on interfacial wettability,deposited film,and interfacial heat transfer behavior.Results showed that when the phosphorus content increased from 0.014wt%to 0.406wt%,the mushy zone enlarged,the complete solidification temperature delayed from1518.3 to 1459.4℃,the final contact angle decreased from 118.4°to 102.8°,indicating improved interfacial contact,and the maximum heat flux increased from 6.9 to 9.2 MW/m2.Increasing the phosphorus content from 0.081wt%to 0.406wt%also accelerated the film deposition rate from 1.57 to 1.73μm per test,resulting in a thickened naturally deposited film with increased thermal resistance that advanced the transition point of heat transfer from the fifth experiment to the third experiment.展开更多
Counterfeiting of modern banknotes poses a significant challenge,prompting the use of various preventive measures.One such measure is the magnetic anti-counterfeiting strip.However,due to its inherent weak magnetic pr...Counterfeiting of modern banknotes poses a significant challenge,prompting the use of various preventive measures.One such measure is the magnetic anti-counterfeiting strip.However,due to its inherent weak magnetic properties,visualizing its magnetic distribution has been a longstanding challenge.In this work,we introduce an innovative method by using a fiber optic diamond probe,a highly sensitive quantum sensor designed specifically for detecting extremely weak magnetic fields.We employ this probe to achieve high-resolution imaging of the magnetic fields associated with the RMB 50denomination anti-counterfeiting strip.Additionally,we conduct computer simulations by using COMSOL Multiphysics software to deduce the potential geometric characteristics and material composition of the magnetic region within the anti-counterfeiting strip.The findings and method presented in this study hold broader significance,extending the RMB 50 denomination to various denominations of the Chinese currency and other items that employ magnetic anti-counterfeiting strips.These advances have the potential to significantly improve and promote security measures in order to prevent the banknotes from being counterfeited.展开更多
An internal defect meter is an instrument to detect the internal inclusion defects of cold-rolled strip steel.The detection accuracy of the equipment can be evaluated based on the similarity of the multiple detection ...An internal defect meter is an instrument to detect the internal inclusion defects of cold-rolled strip steel.The detection accuracy of the equipment can be evaluated based on the similarity of the multiple detection data obtained for the same steel coil.Based on the cosine similarity model and eigenvalue matrix model,a comprehensive evaluation method to calculate the weighted average of similarity is proposed.Results show that the new method is consistent with and can even replace artificial evaluation to realize the automatic evaluation of strip defect detection results.展开更多
Based on the effects of skim components on ammonium removal as well as the current processing technology, a new process-intensified technology of removing ammonia from skim by air stripping on rotating packed bed was ...Based on the effects of skim components on ammonium removal as well as the current processing technology, a new process-intensified technology of removing ammonia from skim by air stripping on rotating packed bed was proposed. The experiments were conducted on a wave-thread packed Rotating Packed Bed(RPB) under atmospheric pressure, suggesting that, in terms of order of importance, the ammonium concentration of feed-stock(x_w), the average ultra-gravity factor(β), feed-stock flux(L), and gas flux(G) had significant impact on ammonium removal rate(η) and the ammonium concentration of products(x_D). In the experiment, mass-transfer coefficient in gas phase(k_ya_e) increases with the increase of β, G/L, and L. The ammonium concentration of products decreases with the increase of β, G/L and the increase of L. The ammonium concentration of products would be as low as ~0.10% and the ammonia removal rate would be 63.21% when skim temperature was 25 °C, x_w0.28%, β 133.2, and G/L 15.0 m^3·L^(-1). Experiment results indicated that the proposed technology for removing ammonium from skim on a rotating packed bed would be a new process-intensified technique compared with traditional aeration process and centrifugal atomization method.展开更多
Continuous and semi-continuous mining technology has become the main trend of modern surface mines in the world. According to the deposit characteristics of coal basin in China and Chinese situation,this paper discuss...Continuous and semi-continuous mining technology has become the main trend of modern surface mines in the world. According to the deposit characteristics of coal basin in China and Chinese situation,this paper discussed the new semi-continuous technology── shovel - transfer wagon-belt conveyor and its application prospect in large surface coal mines in China.展开更多
The aim of the study was to develop actarit double-layered osmotic pump tablets to overcome the weak points of actarit common tablets, such as short half-life and large plasma concentration fluctuations. Single factor...The aim of the study was to develop actarit double-layered osmotic pump tablets to overcome the weak points of actarit common tablets, such as short half-life and large plasma concentration fluctuations. Single factor experiment and orthogonal test were applied to optimize the formulation;the pharmacokinetic study was performed in beagle dogs adopting actarit common tablets as reference tablets. The optimal formulation was as follows: drug layer: 150 mg actarit, 240 mg PEO-N80, 50 mg NaCl;push layer: 140 mg PEO-WSR303, 20 mg NaCl;coating solution: 30 g cellulose acetate and 6 g PEG 4000 in 1000 ml 94% acetone solution, 60 mg coating weight gain. The pharmacokinetic study showed that T max was prolonged by the contrast of commercial common tablets with constant drug release rate, but the bioavailability was equivalent. And a good in vivo –in vitro correlation of the actarit osmotic pump tablets was also established. The designed actarit osmotic pump tablets can be applied for rheumatoid arthritis, proposing a promising replacement for the marked common products.展开更多
Air-stripping method was used to remove ammonia from the wastewater collected from natural gas fertilizer factory. Different materials were used as packing materials for the air stripping system. The effect of pH over...Air-stripping method was used to remove ammonia from the wastewater collected from natural gas fertilizer factory. Different materials were used as packing materials for the air stripping system. The effect of pH over 10.5, air-water flow ratio, nature of packing materials, height of materials and initial influent concentration of ammonia on air stripping unit were investigated. An attempt has been made to find out the stripping con-stant. Stripping constant was found to be .001, 0014, .001 and .0009 for coal, plastic ring, stone chips and wood chips, respectively. Best result was found for plastic ring for its higher surface area. Wood chips did not give good result, because the chips amalgamate with each other and hence reduces the surface area.展开更多
AIM To investigate the efficacy of double-layered covered stent in the treatment of malignant oesophageal obstructions.METHODS A systematic review and meta-analysis was performed following the PRISMA process. Pub Med(...AIM To investigate the efficacy of double-layered covered stent in the treatment of malignant oesophageal obstructions.METHODS A systematic review and meta-analysis was performed following the PRISMA process. Pub Med(Medline),EMBASE(Excerpta Medical Database),AMED(Allied and Complementary medicine Database),Scopus and online content,were searched for studies reporting on the Ni Ti-S polyurethane-covered double oesophageal stent for the treatment of malignant dysphagia. Weighted pooled outcomes were synthesized with a random effects model to account for clinical heterogeneity. All studies reporting the outcome of palliative management of dysphagia due to histologically confirmed malignant oesophageal obstruction using double-layered covered nitinol stent were included. The level of statistical significance was set at α = 0.05.RESULTS Six clinical studies comprising 250 patients in total were identified. Pooled technical success of stent insertion was 97.2%(95%CI: 94.8%-98.9%; I2 = 5.8%). Pooled complication rate was 27.6%(95%CI: 20.7%-35.2%; I2 = 41.9%). Weighted improvement of dysphagia on a scale of 0-5 scoring system was-2.00 [95%CI:-2.29%-(-1.72%); I2 = 87%]. Distal stent migration was documented in 10 out of the 250 cases examined.Pooled stent migration rate was 4.7%(95%CI: 2.5%-7.7%; I2 = 0%). Finally,tumour overgrowth was reported in 34 out of the 250 cases with pooled rate of tumour overgrowth of 11.2%(95%CI: 3.7%-22.1%; I2 = 82.2%). No funnel plot asymmetry to suggest publication bias(bias = 0.39,P = 0.78). In the sensitivity analysis all results were largely similar between the fixed and random effects models.CONCLUSION The double-layered nitinol stent provides immediate relief of malignant dysphagia with low rates of stent migration and tumour展开更多
The chemical stripping method of titanium alloy oxide films was studied. An environment friendly solution hydrogen peroxide and sodium hydroxide without hydrofluoric acid or fluoride were used to strip the oxide films...The chemical stripping method of titanium alloy oxide films was studied. An environment friendly solution hydrogen peroxide and sodium hydroxide without hydrofluoric acid or fluoride were used to strip the oxide films. The morphologies of the surface and cross-section of the oxide films before and after the films stripping were characterized by using scanning electron microscopy (SEM). The microstructure and chemical compositions of the oxide films before and after the films stripping were investigated by using Raman spectroscopy (Raman) and X-ray photoelectron spectroscopy (XPS). It was shown that the thickness of the oxide film was in the range of 5-6 μm. The oxide films were stripped for 2 to 8 min in the solution. Moreover, the effect of the stripping time on the efficiency of the film stripping was investigated, and the optimum stripping time was between 6-8 min. When the stripping solution completely dissolved the whole film, the α/β microstructure of the titanium alloy Ti-10V-2Fe-3Al was partly revealed. The stripping mechanism was discussed in terms of the dissolution of film delamination. The hydrogen peroxide had a significant effect on the dissolution of the titanium alloy anodic oxide film. The feasibility of the dissolution reaction also was evaluated.展开更多
AIM: To evaluate the visual acuity and endothelial cell density according to the thickness in Descemet’s stripping automated endothelial keratoplasty(DSAEK)one year after surgery.METHODS: DSAEK patients’ data were r...AIM: To evaluate the visual acuity and endothelial cell density according to the thickness in Descemet’s stripping automated endothelial keratoplasty(DSAEK)one year after surgery.METHODS: DSAEK patients’ data were reviewed. Thirty seven eyes of 37 patients who underwent DSAEK for pseudophakic bullous keratopathy(PBK) were included in this study. Graft thickness was measured with optical coherence tomography(OCT) 12 mo after DSAEK. Eyes were divided into 3 groups based on the graft thickness:thick(】200 μm), medium-thick(150-200 μm) and thin(【150 μm). Best corrected visual acuity(BCVA),endothelial cells density(ECD) and complications were assessed and comparisons were done between groups.RESULTS: Median thickness of postoperative grafts was 188(range 73-317 μm). There was no significant difference in age, sex, preoperative BCVA, or follow-up period between DSAEK groups. At postoperative 12 mo,mean BCVA was 0.28±0.10 in thick graft group, 0.52±0.08 in medium-thick graft group, and 0.72 ±0.06 in thin graft group. Thin grafts showed better postoperative BCVA as compared with the medium-thick and thick grafts(P =0.001). Thick graft group had 1637.44 ±88.19-mm2,medium thick graft had 1764.50±34.28-mm2 and thin graft group had 1845.30 ±65.62-mm2. Thin graft group had better ECD at 12 mo after surgery(P =0.001).CONCLUSION: Thin grafts after DSAEK ensure better visual rehabilitation. Eyes with thin grafts had significantly lesser loss of ECD compared to eyes withmedium-thick and thick grafts one year after surgery.展开更多
1 INTRODUCTIONInhibition phenomena have frequently been observed in microbial reactions.When thesubstrate concentration in the broth is high enough,the contour curve of the specificgrowth rate of cells is no longer mo...1 INTRODUCTIONInhibition phenomena have frequently been observed in microbial reactions.When thesubstrate concentration in the broth is high enough,the contour curve of the specificgrowth rate of cells is no longer monotonically increasing in a substrate-product phaseplane.The system exhibits a substrate inhibition.Some supersession products can affectthe growth and the yield of the cells as well as the viability of the microorganisms.Forexample,in the case of using Saccharomyces,the ethanol product inhibits the展开更多
A simple, precise and accurate method was developed and validated for the determination of allicin release from alliin/alliinase double-layer tablets. According to Appendix XC Ⅱ of Chinese Pharmacopoeia 2010 edition ...A simple, precise and accurate method was developed and validated for the determination of allicin release from alliin/alliinase double-layer tablets. According to Appendix XC Ⅱ of Chinese Pharmacopoeia 2010 edition Volume II, a small glass-method was adopted at the rotational speed of 100 r/min using 100 mL phosphate buffer (pH 6.8) as release medium. The release amount was determined by HPLC with a C18 column (250 mm × 4.6 mm, 5 μm) using the mobile phase consisting of methanol -0.4% carboxylic acid (65:35) at a flow rate of 1 mL/min and UV detection at 242 nm. The current method demonstrates good linearity over the range 4.052- 405.2 μg/mL (r2=0.9999) with an average recovery of 105.5%(RSD= 1.25%). The accumulative release of alliin/alliinase double-layer tablets had good homogeneity for withinand betweenbatches. The method established is simple, accurate and repeatable for the determination of allicin release from alliin/alliinase double-layer tablets.展开更多
基金funded by the China Postdoctoral Science Foundation(Grant No.2022M721614)the opening project of State Key Laboratory of Explosion Science and Technology,Beijing Institute of Technology(Grant No.KFJJ23-07M)。
文摘This paper proposes a type of double-layer charge liner fabricated using chemical vapor deposition(CVD)that has tungsten as its inner liner.The feasibility of this design was evaluated through penetration tests.Double-layer charge liners were fabricated by using CVD to deposit tungsten layers on the inner surfaces of pure T2 copper liners.The microstructures of the tungsten layers were analyzed using a scanning electron microscope(SEM).The feasibility analysis was carried out by pulsed X-rays,slug-retrieval test and static penetration tests.The shaped charge jet forming and penetration law of inner tungsten-coated double-layer liner were studied by numerical simulation method.The results showed that the double-layer liners could form well-shaped jets.The errors between the X-ray test results and the numerical results were within 11.07%.A slug-retrieval test was found that the retrieved slug was similar to a numerically simulated slug.Compared with the traditional pure copper shaped charge jet,the penetration depth of the double-layer shaped charge liner increased by 11.4% and>10.8% respectively.In summary,the test results are good,and the numerical simulation is in good agreement with the test,which verified the feasibility of using the CVD method to fabricate double-layer charge liners with a high-density and high-strength refractory metal as the inner liner.
基金supported by the State Key Program of National Natural Science Foundation of China(Grant No.12132003)State Key Laboratory of Explosion Science and Technology(Grant No.QNKT20-07)。
文摘The time-sequenced damage behavior of the reactive projectile impacting double-layer plates is discussed.The analytical model considering the combined effect of kinetic and chemical energy is developed to reveal the damage mechanism.The influences of impact velocity and reactive projectile chemical characteristics on the damage effect are decoupled analyzed based on this model.These analyses indicate that the high energy releasing efficiency and fast reaction propagation velocity of the reactive projectile are conducive to enhancing the damage effect.The experiments with various reactive projectiles impact velocity increasing from 702 to 1385 m/s were conducted to verify this model.The experimental results presented that,the damage hole radius of the rear-plate increases with the increase of impact velocity.At the impact velocity of 1350 m/s,the radius of damage hole formed by PTFE/Al/Bi_(2)O_(3),PTFE/Al/MoO_(3),PTFE/Al/Fe_(2)O_(3)projectile on the rear-plate become smaller in sequence.These results are consistent with the analytical model prediction,demonstrating that this model can predict the damage effect quantitatively.This work is of constructive significance to the application of reactive projectiles.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.11905151 and 11875198)the National Key Research and Development Program of China(Grant No.2022YFE03130000)。
文摘Gas-driven permeation(GDP)and plasma-driven permeation(PDP)of hydrogen gas through Ga In Sn/Fe are systematically investigated in this work.The permeation parameters of hydrogen through Ga In Sn/Fe,including diffusivity,Sieverts'constant,permeability,and surface recombination coefficient are obtained.The permeation flux of hydrogen through Ga In Sn/Fe shows great dependence on external conditions such as temperature,hydrogen pressure,and thickness of liquid Ga In Sn.Furthermore,the hydrogen permeation behavior through Ga In Sn/Fe is well consistent with the multilayer permeation theory.In PDP and GDP experiments,hydrogen through Ga In Sn/Fe satisfies the diffusion-limited regime.In addition,the permeation flux of PDP is greater than that of GDP.The increase of hydrogen plasma density hardly causes the hydrogen PDP flux to change within the test scope of this work,which is due to the dissolution saturation.These findings provide guidance for a comprehensive and systematic understanding of hydrogen isotope recycling,permeation,and retention in plasma-facing components under actual conditions.
基金Funded by the Natural Science Foundation of Nanping of China(No.N2021J002)Guangdong Basic and Applied Basic Research Foundation(No.2020A1515110304)+3 种基金Guangzhou Science and Technology Plan(No.202102020224)Natural Science Foundation of Fujian Province(No.2020Y0092)Natural Science Foundation of Fujian Province(No.2023J011044)Resource Chemical Industry and Technology Foundation of Nanping(No.N2020Z003)。
文摘To develop the microwave absorbing(MA)properties of cementitious material mixed with mine solid waste,the iron tailings cementitious microwave absorbing materials were prepared.The iron tailings was treated into different particle sizes by planetary ball mill,and the physicochemical properties of iron tailings were tested by laser particle size analyzer and scanning electron microscope(SEM).The electromagnetic parameters of iron tailings cementitious materials were characterized by a vector network analyzer and simulated MA properties,and the MA properties of iron tailings-cement composite system with steel fiber as absorber was studied.Based on the design of the single-layer structure,optimum mix ratio and thickness configuration method of double-layer structure were further studied,meanwhile,the mechanical properties and engineering application were analyzed and discussed.The results show that the particle size of iron tailings can afiect its electromagnetic behavior in cementitious materials,and the smaller particles lead the increase of demagnetisation efiect induced by domain wall motion and achieve better microwave absorbing properties in cementitious materials.When the thickness of matching layer and absorbing layer is 5 mm,the optimized microwave absorbing properties of C1/C3 double-layer cementitious material can obtain optimal RL value of-27.61 dB and efiective absorbing bandwidth of 0.97 GHz,which attributes to the synergistic efiect of impedance matching and attenuation characteristics.The double-layer microwave absorbing materials obtain excellent absorbing properties and show great design flexibility and diversity,which can be used as a suitable candidate for the preparation of favorable microwave absorbing cementitious materials.
基金supported by the NationalNatural Science Foundation of China Under Grant 61961017Key R&D Plan Projects in Hubei Province 2022BAA060.
文摘To reduce the comprehensive costs of the construction and operation of microgrids and to minimize the power fluctuations caused by randomness and intermittency in distributed generation,a double-layer optimizing configuration method of hybrid energy storage microgrid based on improved grey wolf optimization(IGWO)is proposed.Firstly,building a microgrid system containing a wind-solar power station and electric-hydrogen coupling hybrid energy storage system.Secondly,the minimum comprehensive cost of the construction and operation of the microgrid is taken as the outer objective function,and the minimum peak-to-valley of the microgrid’s daily output is taken as the inner objective function.By iterating through the outer and inner layers,the system improves operational stability while achieving economic configuration.Then,using the energy-self-smoothness of the microgrid as the evaluation index,a double-layer optimizing configuration method of the microgrid is constructed.Finally,to improve the disadvantages of grey wolf optimization(GWO),such as slow convergence in the later period and easy falling into local optima,by introducing the convergence factor nonlinear adjustment strategy and Cauchy mutation operator,an IGWO with excellent global performance is proposed.After testing with the typical test functions,the superiority of IGWO is verified.Next,using IGWO to solve the double-layer model.The case analysis shows that compared to GWO and particle swarm optimization(PSO),the IGWO reduced the comprehensive cost by 15.6%and 18.8%,respectively.Therefore,the proposed double-layer optimizationmethod of capacity configuration ofmicrogrid with wind-solar-hybrid energy storage based on IGWO could effectively improve the independence and stability of the microgrid and significantly reduce the comprehensive cost.
基金supported by the Scientific and Innovative Action Plan of Shanghai(21N31900800)Shanghai Rising-Star Program(23QB1403500)+4 种基金the Shanghai Sailing Program(20YF1443000)Shanghai Science and Technology Commission,the Belt and Road Project(20310750500)Talent Project of SAAS(2023-2025)Runup Plan of SAAS(ZP22211)the SAAS Program for Excellent Research Team(2022(B-16))。
文摘Traditional transgenic detection methods require high test conditions and struggle to be both sensitive and efficient.In this study,a one-tube dual recombinase polymerase amplification(RPA)reaction system for CP4-EPSPS and Cry1Ab/Ac was proposed and combined with a lateral flow immunochromatographic assay,named“Dual-RPA-LFD”,to visualize the dual detection of genetically modified(GM)crops.In which,the herbicide tolerance gene CP4-EPSPS and the insect resistance gene Cry1Ab/Ac were selected as targets taking into account the current status of the most widespread application of insect resistance and herbicide tolerance traits and their stacked traits.Gradient diluted plasmids,transgenic standards,and actual samples were used as templates to conduct sensitivity,specificity,and practicality assays,respectively.The constructed method achieved the visual detection of plasmid at levels as low as 100 copies,demonstrating its high sensitivity.In addition,good applicability to transgenic samples was observed,with no cross-interference between two test lines and no influence from other genes.In conclusion,this strategy achieved the expected purpose of simultaneous detection of the two popular targets in GM crops within 20 min at 37°C in a rapid,equipmentfree field manner,providing a new alternative for rapid screening for transgenic assays in the field.
文摘AIM:To report the outcomes of three cases of corneal perforation managed with simultaneous tectonic Descemet stripping endothelial keratoplasty(t-DSEK)and tectonic Bowman layer transplant(t-BLT)as an alternative to tectonic penetrating keratoplasty(t-PKP).METHODS:Three eyes of three patients receiving simultaneous t-DSEK and t-BLT for corneal perforation were included.The technique for DSEK was modified depending on individual requirements.The t-BLT technique was standardised using an 8 mm graft and fixated with a running suture.Success was measured by the ability of this procedure to close a corneal perforation.RESULTS:All three cases achieved tectonic eye globe restoration and remained stable during the minimum 3-month observation period.Reinterventions were relatively common:2 cases required amniotic membrane transplant for persistent epithelial defects.One case required DSEK rebubbling.One case developed angle closure glaucoma requiring surgical peripheral iridectomy.CONCLUSION:Simultaneous t-DSEK and t-BLT may be a useful strategy for the management of corneal perforation as an alternative management to t-PKP for selected cases.
基金supported from the National Natural Science Foundation of China(Nos.52204356,52274342,and 52130408)the Natural Science Foundation of Hunan Province,China(Nos.2023JJ40762 and 2021JJ40731)。
文摘The interfacial wettability and heat transfer behavior are crucial in the strip casting of high phosphorus-containing steel.A hightemperature simulation of strip casting was conducted using the droplet solidification technique with the aims to reveal the effects of phosphorus content on interfacial wettability,deposited film,and interfacial heat transfer behavior.Results showed that when the phosphorus content increased from 0.014wt%to 0.406wt%,the mushy zone enlarged,the complete solidification temperature delayed from1518.3 to 1459.4℃,the final contact angle decreased from 118.4°to 102.8°,indicating improved interfacial contact,and the maximum heat flux increased from 6.9 to 9.2 MW/m2.Increasing the phosphorus content from 0.081wt%to 0.406wt%also accelerated the film deposition rate from 1.57 to 1.73μm per test,resulting in a thickened naturally deposited film with increased thermal resistance that advanced the transition point of heat transfer from the fifth experiment to the third experiment.
基金Project supported by the National Key Research and Development Program of China (Grant No.2021YFB2012600)the Shanghai Aerospace Science and Technology Innovation Fund,China (Grant No.SAST-2022-102)。
文摘Counterfeiting of modern banknotes poses a significant challenge,prompting the use of various preventive measures.One such measure is the magnetic anti-counterfeiting strip.However,due to its inherent weak magnetic properties,visualizing its magnetic distribution has been a longstanding challenge.In this work,we introduce an innovative method by using a fiber optic diamond probe,a highly sensitive quantum sensor designed specifically for detecting extremely weak magnetic fields.We employ this probe to achieve high-resolution imaging of the magnetic fields associated with the RMB 50denomination anti-counterfeiting strip.Additionally,we conduct computer simulations by using COMSOL Multiphysics software to deduce the potential geometric characteristics and material composition of the magnetic region within the anti-counterfeiting strip.The findings and method presented in this study hold broader significance,extending the RMB 50 denomination to various denominations of the Chinese currency and other items that employ magnetic anti-counterfeiting strips.These advances have the potential to significantly improve and promote security measures in order to prevent the banknotes from being counterfeited.
文摘An internal defect meter is an instrument to detect the internal inclusion defects of cold-rolled strip steel.The detection accuracy of the equipment can be evaluated based on the similarity of the multiple detection data obtained for the same steel coil.Based on the cosine similarity model and eigenvalue matrix model,a comprehensive evaluation method to calculate the weighted average of similarity is proposed.Results show that the new method is consistent with and can even replace artificial evaluation to realize the automatic evaluation of strip defect detection results.
基金Supported by the Opening Project Fund of Key Laboratory of Danzhou Investigation&Experiment Station of Tropical Crops,Ministry of Agriculture(RRI-KLOF201701)
文摘Based on the effects of skim components on ammonium removal as well as the current processing technology, a new process-intensified technology of removing ammonia from skim by air stripping on rotating packed bed was proposed. The experiments were conducted on a wave-thread packed Rotating Packed Bed(RPB) under atmospheric pressure, suggesting that, in terms of order of importance, the ammonium concentration of feed-stock(x_w), the average ultra-gravity factor(β), feed-stock flux(L), and gas flux(G) had significant impact on ammonium removal rate(η) and the ammonium concentration of products(x_D). In the experiment, mass-transfer coefficient in gas phase(k_ya_e) increases with the increase of β, G/L, and L. The ammonium concentration of products decreases with the increase of β, G/L and the increase of L. The ammonium concentration of products would be as low as ~0.10% and the ammonia removal rate would be 63.21% when skim temperature was 25 °C, x_w0.28%, β 133.2, and G/L 15.0 m^3·L^(-1). Experiment results indicated that the proposed technology for removing ammonium from skim on a rotating packed bed would be a new process-intensified technique compared with traditional aeration process and centrifugal atomization method.
文摘Continuous and semi-continuous mining technology has become the main trend of modern surface mines in the world. According to the deposit characteristics of coal basin in China and Chinese situation,this paper discussed the new semi-continuous technology── shovel - transfer wagon-belt conveyor and its application prospect in large surface coal mines in China.
文摘The aim of the study was to develop actarit double-layered osmotic pump tablets to overcome the weak points of actarit common tablets, such as short half-life and large plasma concentration fluctuations. Single factor experiment and orthogonal test were applied to optimize the formulation;the pharmacokinetic study was performed in beagle dogs adopting actarit common tablets as reference tablets. The optimal formulation was as follows: drug layer: 150 mg actarit, 240 mg PEO-N80, 50 mg NaCl;push layer: 140 mg PEO-WSR303, 20 mg NaCl;coating solution: 30 g cellulose acetate and 6 g PEG 4000 in 1000 ml 94% acetone solution, 60 mg coating weight gain. The pharmacokinetic study showed that T max was prolonged by the contrast of commercial common tablets with constant drug release rate, but the bioavailability was equivalent. And a good in vivo –in vitro correlation of the actarit osmotic pump tablets was also established. The designed actarit osmotic pump tablets can be applied for rheumatoid arthritis, proposing a promising replacement for the marked common products.
文摘Air-stripping method was used to remove ammonia from the wastewater collected from natural gas fertilizer factory. Different materials were used as packing materials for the air stripping system. The effect of pH over 10.5, air-water flow ratio, nature of packing materials, height of materials and initial influent concentration of ammonia on air stripping unit were investigated. An attempt has been made to find out the stripping con-stant. Stripping constant was found to be .001, 0014, .001 and .0009 for coal, plastic ring, stone chips and wood chips, respectively. Best result was found for plastic ring for its higher surface area. Wood chips did not give good result, because the chips amalgamate with each other and hence reduces the surface area.
文摘AIM To investigate the efficacy of double-layered covered stent in the treatment of malignant oesophageal obstructions.METHODS A systematic review and meta-analysis was performed following the PRISMA process. Pub Med(Medline),EMBASE(Excerpta Medical Database),AMED(Allied and Complementary medicine Database),Scopus and online content,were searched for studies reporting on the Ni Ti-S polyurethane-covered double oesophageal stent for the treatment of malignant dysphagia. Weighted pooled outcomes were synthesized with a random effects model to account for clinical heterogeneity. All studies reporting the outcome of palliative management of dysphagia due to histologically confirmed malignant oesophageal obstruction using double-layered covered nitinol stent were included. The level of statistical significance was set at α = 0.05.RESULTS Six clinical studies comprising 250 patients in total were identified. Pooled technical success of stent insertion was 97.2%(95%CI: 94.8%-98.9%; I2 = 5.8%). Pooled complication rate was 27.6%(95%CI: 20.7%-35.2%; I2 = 41.9%). Weighted improvement of dysphagia on a scale of 0-5 scoring system was-2.00 [95%CI:-2.29%-(-1.72%); I2 = 87%]. Distal stent migration was documented in 10 out of the 250 cases examined.Pooled stent migration rate was 4.7%(95%CI: 2.5%-7.7%; I2 = 0%). Finally,tumour overgrowth was reported in 34 out of the 250 cases with pooled rate of tumour overgrowth of 11.2%(95%CI: 3.7%-22.1%; I2 = 82.2%). No funnel plot asymmetry to suggest publication bias(bias = 0.39,P = 0.78). In the sensitivity analysis all results were largely similar between the fixed and random effects models.CONCLUSION The double-layered nitinol stent provides immediate relief of malignant dysphagia with low rates of stent migration and tumour
基金Funded by the National Natural Science Foundation of China(No. 51171011)
文摘The chemical stripping method of titanium alloy oxide films was studied. An environment friendly solution hydrogen peroxide and sodium hydroxide without hydrofluoric acid or fluoride were used to strip the oxide films. The morphologies of the surface and cross-section of the oxide films before and after the films stripping were characterized by using scanning electron microscopy (SEM). The microstructure and chemical compositions of the oxide films before and after the films stripping were investigated by using Raman spectroscopy (Raman) and X-ray photoelectron spectroscopy (XPS). It was shown that the thickness of the oxide film was in the range of 5-6 μm. The oxide films were stripped for 2 to 8 min in the solution. Moreover, the effect of the stripping time on the efficiency of the film stripping was investigated, and the optimum stripping time was between 6-8 min. When the stripping solution completely dissolved the whole film, the α/β microstructure of the titanium alloy Ti-10V-2Fe-3Al was partly revealed. The stripping mechanism was discussed in terms of the dissolution of film delamination. The hydrogen peroxide had a significant effect on the dissolution of the titanium alloy anodic oxide film. The feasibility of the dissolution reaction also was evaluated.
文摘AIM: To evaluate the visual acuity and endothelial cell density according to the thickness in Descemet’s stripping automated endothelial keratoplasty(DSAEK)one year after surgery.METHODS: DSAEK patients’ data were reviewed. Thirty seven eyes of 37 patients who underwent DSAEK for pseudophakic bullous keratopathy(PBK) were included in this study. Graft thickness was measured with optical coherence tomography(OCT) 12 mo after DSAEK. Eyes were divided into 3 groups based on the graft thickness:thick(】200 μm), medium-thick(150-200 μm) and thin(【150 μm). Best corrected visual acuity(BCVA),endothelial cells density(ECD) and complications were assessed and comparisons were done between groups.RESULTS: Median thickness of postoperative grafts was 188(range 73-317 μm). There was no significant difference in age, sex, preoperative BCVA, or follow-up period between DSAEK groups. At postoperative 12 mo,mean BCVA was 0.28±0.10 in thick graft group, 0.52±0.08 in medium-thick graft group, and 0.72 ±0.06 in thin graft group. Thin grafts showed better postoperative BCVA as compared with the medium-thick and thick grafts(P =0.001). Thick graft group had 1637.44 ±88.19-mm2,medium thick graft had 1764.50±34.28-mm2 and thin graft group had 1845.30 ±65.62-mm2. Thin graft group had better ECD at 12 mo after surgery(P =0.001).CONCLUSION: Thin grafts after DSAEK ensure better visual rehabilitation. Eyes with thin grafts had significantly lesser loss of ECD compared to eyes withmedium-thick and thick grafts one year after surgery.
文摘1 INTRODUCTIONInhibition phenomena have frequently been observed in microbial reactions.When thesubstrate concentration in the broth is high enough,the contour curve of the specificgrowth rate of cells is no longer monotonically increasing in a substrate-product phaseplane.The system exhibits a substrate inhibition.Some supersession products can affectthe growth and the yield of the cells as well as the viability of the microorganisms.Forexample,in the case of using Saccharomyces,the ethanol product inhibits the
文摘A simple, precise and accurate method was developed and validated for the determination of allicin release from alliin/alliinase double-layer tablets. According to Appendix XC Ⅱ of Chinese Pharmacopoeia 2010 edition Volume II, a small glass-method was adopted at the rotational speed of 100 r/min using 100 mL phosphate buffer (pH 6.8) as release medium. The release amount was determined by HPLC with a C18 column (250 mm × 4.6 mm, 5 μm) using the mobile phase consisting of methanol -0.4% carboxylic acid (65:35) at a flow rate of 1 mL/min and UV detection at 242 nm. The current method demonstrates good linearity over the range 4.052- 405.2 μg/mL (r2=0.9999) with an average recovery of 105.5%(RSD= 1.25%). The accumulative release of alliin/alliinase double-layer tablets had good homogeneity for withinand betweenbatches. The method established is simple, accurate and repeatable for the determination of allicin release from alliin/alliinase double-layer tablets.