缆式焊丝熔化极气体保护电弧焊(gas metal arc welding,GMAW)中存在的焊缝截面侧偏现象会导致焊接接头熔合不良,基于熔滴受力分析和最小电压理论对焊缝截面侧偏现象的变化规律进行机理分析.结果表明,电流是影响截面侧偏的关键因素,由于...缆式焊丝熔化极气体保护电弧焊(gas metal arc welding,GMAW)中存在的焊缝截面侧偏现象会导致焊接接头熔合不良,基于熔滴受力分析和最小电压理论对焊缝截面侧偏现象的变化规律进行机理分析.结果表明,电流是影响截面侧偏的关键因素,由于缆式焊丝独特的绞合结构引起电弧旋转,进而导致出现熔滴受力不均的现象,熔滴过渡方向与焊丝轴线存在夹角,在熔滴冲击力的作用下导致焊缝截面出现侧偏现象,随着电流的增加,电弧对熔滴的拘束增强,熔滴过渡方向逐渐趋于轴线,因而焊缝截面侧偏的趋势随着电流增加而减小.展开更多
针对窄间隙熔化极气体保护焊(Gas Metal Arc Welding,GMAW)焊道侧壁处局部咬边缺陷检测困难的问题,提出了一种基于电弧声信号特征提取与处理的咬边缺陷在线检测方法。通过分析正常、临界咬边和咬边这3种焊接状态的电弧形态和电弧声信号...针对窄间隙熔化极气体保护焊(Gas Metal Arc Welding,GMAW)焊道侧壁处局部咬边缺陷检测困难的问题,提出了一种基于电弧声信号特征提取与处理的咬边缺陷在线检测方法。通过分析正常、临界咬边和咬边这3种焊接状态的电弧形态和电弧声信号特征,证实坡口侧壁引起的电弧形态变化是影响电弧声信号变化的重要因素。在此基础上采用小波包时频分析,同时引入特征类间标准差作为评价指标,确定了能有效识别3种焊接状态的敏感特征。采用Sigmoid支持向量机和五折交叉验证建立预测模型,实验结果表明该模型能较好地实现3种焊接状态的预测分类,识别准确率达到96.0%。展开更多
随着全球制造业竞争的日益激烈,我国提出了“中国制造2025”制造强国战略,其重点发展的十大领域中,与焊接技术密切相关的就高达八个,不仅极大地推动了焊接技术的革新发展,而且对焊接效率和质量均提出了更高的要求。由于熔化极气体保护焊...随着全球制造业竞争的日益激烈,我国提出了“中国制造2025”制造强国战略,其重点发展的十大领域中,与焊接技术密切相关的就高达八个,不仅极大地推动了焊接技术的革新发展,而且对焊接效率和质量均提出了更高的要求。由于熔化极气体保护焊(Gas metal arc welding,GMAW)易于实现自动化焊接,具有生产效率高、焊接质量好及位置适应性好等优点,所以广泛应用于机械制造业中。实现高效GMAW的主要途径有提高焊接速度以及焊接熔敷率。针对以上两种途径,国内外焊接工作者在双丝GMAW的基础上,引入了第三根甚至多根焊丝,研发了各种多丝GMAW工艺。本文针对国内外研发的各类多丝GMAW工艺进行了分析,重点介绍了多丝GMAW工艺的焊接原理、工艺特点及其应用,通过上述分析对各类多丝GMAW工艺进行归纳总结,并进一步展望了多丝焊接的发展方向,即多丝GMAW工艺亟需在电弧物理理论、设备开发和新焊材研发等方面展开深入的研究工作。展开更多
Double-pulse LIBS is a promising technique for deep-sea applications.LIBS measurements in shallow water with up to 400 mJ each pulse were done to select laser parameters which promote optimized spectral line emission ...Double-pulse LIBS is a promising technique for deep-sea applications.LIBS measurements in shallow water with up to 400 mJ each pulse were done to select laser parameters which promote optimized spectral line emission from plasma even at elevated pressures,where line broadening until loss of most of the spectral information can occur.Optical emission spectroscopy,using a Czerny-Turner spectrometer,has been applied to investigate the dependence of the emitted radiation on laser parameters and hydrostatic pressure.It has been found,that higher laser pulse energies,especially with short pulse delay as required in high water pressure,can also have an adverse effect on the measured spectrum.展开更多
Welding voltage and current in arc signals are directly related to arc stability and welding quality.Process experiments with different parameters were organized according to the orthogonal experimental design method ...Welding voltage and current in arc signals are directly related to arc stability and welding quality.Process experiments with different parameters were organized according to the orthogonal experimental design method by constructing an aluminum alloy double-pulse metal inert gas(MIG)welding arc electric signal test platform.The data acquisition system of the aluminum alloy MIG welding process was established to obtain real-time arc signal information reflecting the welding process.The aluminum alloy’s collected double-pulse arc current signals are decomposed adaptively by broadband mode decomposition(BMD).The direct current(DC)signal,pulse signal,distortion signal,ripple signal,and noise signal are separated and extracted,and the composite multiscale fuzzy entropy(CMFE)is calculated for the component set of the electrical signal.The experimental results show that the current waveform obtained by the double-pulse MIG welding current signal is consistent with the corresponding weld forming diagram.Simultaneously,the composite multiscale fuzzy entropy is calculated for the arc characteristic parameters.The rationality of matching process parameters and arc stability of aluminum alloy’s double-pulse MIG welding were evaluated.展开更多
The effect of current on the morphology of Al alloy T-joint in double-pulsed metal inert gas（DP-MIG） welding process was investigated by simulation and experiment.A three-dimensional finite element model and the DP-...The effect of current on the morphology of Al alloy T-joint in double-pulsed metal inert gas（DP-MIG） welding process was investigated by simulation and experiment.A three-dimensional finite element model and the DP-MIG heat source of double-ellipsoidal volumetric model were developed to simulate the temperature and stress fields under different welding conditions.The macro-morphology and microstructure of welding joints at the corresponding currents were observed in the experiment.The results show that the best condition is at an average current of 90 A and current difference of 40 A,when the maximum temperature is 200 °C higher than the fusion points,with the temperature difference of about 100 °C and stress change of 10 MPa between thermal pulse and thermal base.Under these conditions,Al alloy T-joint with proper fusion condition has smooth fish-scale welding appearance and finer microstructure.Furthermore,the thermal curves and stress distribution in the experiment are consistent with those in the simulation,verifying the precision of the welding simulation.展开更多
文摘缆式焊丝熔化极气体保护电弧焊(gas metal arc welding,GMAW)中存在的焊缝截面侧偏现象会导致焊接接头熔合不良,基于熔滴受力分析和最小电压理论对焊缝截面侧偏现象的变化规律进行机理分析.结果表明,电流是影响截面侧偏的关键因素,由于缆式焊丝独特的绞合结构引起电弧旋转,进而导致出现熔滴受力不均的现象,熔滴过渡方向与焊丝轴线存在夹角,在熔滴冲击力的作用下导致焊缝截面出现侧偏现象,随着电流的增加,电弧对熔滴的拘束增强,熔滴过渡方向逐渐趋于轴线,因而焊缝截面侧偏的趋势随着电流增加而减小.
文摘针对窄间隙熔化极气体保护焊(Gas Metal Arc Welding,GMAW)焊道侧壁处局部咬边缺陷检测困难的问题,提出了一种基于电弧声信号特征提取与处理的咬边缺陷在线检测方法。通过分析正常、临界咬边和咬边这3种焊接状态的电弧形态和电弧声信号特征,证实坡口侧壁引起的电弧形态变化是影响电弧声信号变化的重要因素。在此基础上采用小波包时频分析,同时引入特征类间标准差作为评价指标,确定了能有效识别3种焊接状态的敏感特征。采用Sigmoid支持向量机和五折交叉验证建立预测模型,实验结果表明该模型能较好地实现3种焊接状态的预测分类,识别准确率达到96.0%。
文摘随着全球制造业竞争的日益激烈,我国提出了“中国制造2025”制造强国战略,其重点发展的十大领域中,与焊接技术密切相关的就高达八个,不仅极大地推动了焊接技术的革新发展,而且对焊接效率和质量均提出了更高的要求。由于熔化极气体保护焊(Gas metal arc welding,GMAW)易于实现自动化焊接,具有生产效率高、焊接质量好及位置适应性好等优点,所以广泛应用于机械制造业中。实现高效GMAW的主要途径有提高焊接速度以及焊接熔敷率。针对以上两种途径,国内外焊接工作者在双丝GMAW的基础上,引入了第三根甚至多根焊丝,研发了各种多丝GMAW工艺。本文针对国内外研发的各类多丝GMAW工艺进行了分析,重点介绍了多丝GMAW工艺的焊接原理、工艺特点及其应用,通过上述分析对各类多丝GMAW工艺进行归纳总结,并进一步展望了多丝焊接的发展方向,即多丝GMAW工艺亟需在电弧物理理论、设备开发和新焊材研发等方面展开深入的研究工作。
基金funded by the Deutsche Forschungsgemeinschaft(DFG,German Research Foundation)–Project No.454848899。
文摘Double-pulse LIBS is a promising technique for deep-sea applications.LIBS measurements in shallow water with up to 400 mJ each pulse were done to select laser parameters which promote optimized spectral line emission from plasma even at elevated pressures,where line broadening until loss of most of the spectral information can occur.Optical emission spectroscopy,using a Czerny-Turner spectrometer,has been applied to investigate the dependence of the emitted radiation on laser parameters and hydrostatic pressure.It has been found,that higher laser pulse energies,especially with short pulse delay as required in high water pressure,can also have an adverse effect on the measured spectrum.
基金The 2024 University-level Higher Education Teaching Reform Project of Guangzhou Xinhua University,“Teaching Reform and Practice Based on OBE Concept”:A Case Study of“University Physics Experiment”(Project No.2024J044)。
文摘Welding voltage and current in arc signals are directly related to arc stability and welding quality.Process experiments with different parameters were organized according to the orthogonal experimental design method by constructing an aluminum alloy double-pulse metal inert gas(MIG)welding arc electric signal test platform.The data acquisition system of the aluminum alloy MIG welding process was established to obtain real-time arc signal information reflecting the welding process.The aluminum alloy’s collected double-pulse arc current signals are decomposed adaptively by broadband mode decomposition(BMD).The direct current(DC)signal,pulse signal,distortion signal,ripple signal,and noise signal are separated and extracted,and the composite multiscale fuzzy entropy(CMFE)is calculated for the component set of the electrical signal.The experimental results show that the current waveform obtained by the double-pulse MIG welding current signal is consistent with the corresponding weld forming diagram.Simultaneously,the composite multiscale fuzzy entropy is calculated for the arc characteristic parameters.The rationality of matching process parameters and arc stability of aluminum alloy’s double-pulse MIG welding were evaluated.
基金Project(51475156)supported by the National Natural Science Foundation of China
文摘The effect of current on the morphology of Al alloy T-joint in double-pulsed metal inert gas（DP-MIG） welding process was investigated by simulation and experiment.A three-dimensional finite element model and the DP-MIG heat source of double-ellipsoidal volumetric model were developed to simulate the temperature and stress fields under different welding conditions.The macro-morphology and microstructure of welding joints at the corresponding currents were observed in the experiment.The results show that the best condition is at an average current of 90 A and current difference of 40 A,when the maximum temperature is 200 °C higher than the fusion points,with the temperature difference of about 100 °C and stress change of 10 MPa between thermal pulse and thermal base.Under these conditions,Al alloy T-joint with proper fusion condition has smooth fish-scale welding appearance and finer microstructure.Furthermore,the thermal curves and stress distribution in the experiment are consistent with those in the simulation,verifying the precision of the welding simulation.
