Formation, microstructure and mechanical properties of double-sided laser beam welded Ti-6Al-4V T-joint

The T-joints of Ti?6Al?4V alloy were manufactured by double-sided synchronized laser beam welding with the homologous filler wire. The formation, microstructure and mechanical properties of welded joints as well as the correlations of each other were investigated. The results indicate that the quality of weld seams is good without defects such as discontinuity, beading, visible cracks or porosity, which is linked to the steady molten pool behavior and droplet transition. The morphologies of the heat affected zone (HAZ) located on the skin and stringer are disparate. The microstructure of the HAZ and fusion zone (FZ) is mainly comprised of acicular martensiticα′ phases. The microhardness of the HAZ and FZ is higher than that of the base metal (BM) and reaches a maximum value at the HAZ near FZ on the stringer. The tensile specimens along the skin and stringer fractured at the BM with ductile fracture surfaces.

Numerical Simulation of Current Density Distribution in Keyhole Double-Sided Arc Welding

In the double-sided arc welding system (DSAW) composing of PAW+TIG arcs, the PAW arc is guided by the TIG arc so that the current mostly flows through the direction of the workpiece thickness and the penetration is greatly improved. To analyze the current density distribution in DSAW is beneficial to understanding of this process. Considering all kinds of dynamic factors acting on the weldpool, this paper discusses firstly the surface deformation of the weldpool and the keyhole formation in PAW+TIG DSAW process on the basis of the magnetohydrodynamic theory and variation principles. Hence, a model of the current density distribution is developed. Through numerical simulation, the current density distribution in PAW+TIG DSAW process is quantitatively analyzed. It shows that the minimal radius of keyhole formed in PAW+TIG DSAW process is 0.5 mm and 89.5 percent of current flows through the keyhole.

Keyhole Double-Sided Arc Welding Process

In the proposed method, the current/arc is guided through the keyhole so that the energy of the plasma jet is compensated while it is consumed in heating the workpiece along the keyhole. As a result, deep narrow penetration has been achieved on 12.7 mm (1/2') thick stainless steel plates using 70 A welding current.

Effect of pin penetration depth on double-sided friction stir welded joints of AA6061-T913 alloy

Friction stir welding (FSW) of aluminum alloys is currently utilized in several modern industries. The joints must have sufficient elastic?plastic response and formability levels similar to that of the base metal. In this work, double-sided FSW of AA6061 sheet was compared with its conventional single-sided one. An adjustable tool with different pin lengths (50%?95% of the sheet thickness) was used to perform the double-sided welds. Macro- and micro-structures, strength, and hardness of the joints were investigated to determine the optimum pin penetration depth. The best results were obtained for a double-sided joint made by a pin length equal to 65% of the sheet thickness, which showed an increase of 41% in the ultimate tensile strength compared with the single-sided joint.

Effect of Ca addition on the microstructure and the mechanical properties of asymmetric double-sided friction stir welded AZ61 magnesium alloy

The effects of 2%Ca addition on the microstructure and the mechanical properties of the asymmetric double-sided friction stir welded magnesium alloy AZ61 were investigated.Compared to the Ca-free AZ61magnesium alloy,the addition of 2%Ca significantly refines the grains in the stir zone after welding.Due to the existence of thermally stable Al2Ca particles,there is no noticeable change in the grain size in the stir zone regardless of the welding heat input.The electron backscattered diffraction analysis at the center of the stir zone confirmed the significant deterioration of the(0001)texture strength from the addition of 2%Ca.The tensile test of the joint suggested that the addition of 2%Ca provides stable tensile properties to the joint regardless of the welding parameters.The critical(0001)texture strength that determines the ultimate tensile strength decreased from 20 to 15 by the Ca addition.The addition of Ca enhanced the deterioration of the plastic elongation when the(0001)texture strength increased.

Effect of arc distance on temperature field and weld shape during double-sided arc welding

A new high efficiency welding method, double-sided double arc welding with double powers （DSAW-D）, is developed for thick plate of low alloy high strength steel in this study. It is well known that the thermal cycles have an important influence on the microstructure, shape, stress, distortion and mechanical property. The DSA W-D method can control the temperature field on a wide range by regulating the distance between two arcs, improve the microstructure and prevent hot and cold cracking of high strength steel. But at present, the effect of arc distance on the temperature field and shape is not clear. Therefore, the paper researches the effect of arc distance on the temperature field and weld pool during DSAW-D using finite element method. The transient temperature field of different arc distance in DSAW-D is calculated. To verify the numerical results, the temperature is measured by the thermo-couple and the calculated results agree approximately with experimental data. Farther, the thermal property and mutual effect of double-sided arcs are investigated. The temperature distributions and weld pool profile at different arc distances are obtained. The results show that arc distance is a very important factor to affect the heat process.

Microstructure of stainless steel weld in double-sided arc welding

Double-sided arc welding with a single power source can effectively increase the weld penetration, diminish distortion, improve welding speed and save energy. Compared to conventional arc welding processes, double-sided arc welding can generate a penetrating electromaguetic field to help to form fine dendritic microstrueture in the weld due to the symmetry of heating. Type 1Cr1SNi9Ti aastenitic stainless steel was bead-on-plate welded with double-sided arc welding and conventional plasma arc welding processes, respectively, and microstructure in the weld, heat-affected zone and base metal were examined. After analyzing the black carbon-enriched band in the weld during plasma arc welding with electron probe microanalyzer （ EPMA ） and X-ray diffraction （XRD） technology, it was found that the black band was shaped from the aggregation of ferrite in the fasion boundary. Hardness measurement showed that this black band does not apparently affect the microhardncss distribution in the weld.

Microstructures and hardness of flat-overhead weld of the high strength steel thick plate using double-sided arc welding

High strength steel thick plate is widely used in shipbuilding, pressure vessels, etc. , the balance between weld quality and welding efficiency is becoming a research focus. In this paper, double-sided double arc fiat-overhead welding experiments for high strength steel thick plate were conducted. Microstructures of weld have been observed through optical microscope （OM） and scanning electron microscope （SEM）. Transformation of microstructures under thermal cycles of multi peaks was analyzed. Macro and micro hardness were also tested. The results show that the heat-affected zone （HAZ） near the fusion line experiences thermal cycles up to three times. The microstructures there are the most complex, including coarse lath martensite in original coarse-grained zone, and net-like structure along grain boundaries in critical reheat coarse-grained zone. After several times of tempering for bucking welding, the features of acicula and lath are weakened. Its microstructure approaches to the microstructure of base metal which is tempering sorbite. The hardness test shows that the maximum hardness occurs at critical reheat coarse-grained zone, the hardness of reticulation structure at grain boundary can be up to 450 HV.

Numerical Simulation of Electromagnetic Force in Double-Sided Arc Welding Process

Up till now, most of the researchers believe that there are four kinds of forces in the weld pool convection, they aresurface tension, electromagnetic force, buoyancy and gas shear stress. So electromagnetic force is very important,especially when large current is applied. In most of previous models, the electromagnetic force is calculated analytically,in which only the axial component of current is considered. Actually the radial component of current has thesame effect, and may be advanced in some locations. In double-sided arc welding process, instead of the earthclamp, another torch is placed on the opposite side; the current will go from one torch, through the weld zone,to another torch. In this case, the current is more concentrated in the weld zone; the electromagnetic force willhave significant effect compared with conventional welding process. In this paper, a new method of numericalcalculation for electromagnetic force is developed, in which both axial and radial components are considered. And asan example, the distribution of electromagnetic force in double-sided arc welding is calculated. It demonstrates thatthis new method could give more accurate simulation of electromagnetic force, and is close to the actual process.

Double-sided gas tungsten arc welding process on TC4 titanium alloy

TC4 titanium alloy was welded by double-sided gas tungsten arc welding(GTAW) process in comparison with conventional GTAW process, the microstructure and mechanical performance of weld were also studied. The results indicate that double-sided GTAW is superior over regular single-sided GTAW on the aspects of increasing penetration, reducing welding deformation and improving welding efficiency. Good weld joint was obtained, which can reach 96.14% tensile strength and 70.85% elongation percentage of the base metal. The grains in heat-affected zone(HAZ) are thin and equiaxed and the degree of grain coarsening increases as one moves to the weld center line, and the interior of grains are α and α′ structures. The coarse columned and equiaxed grains, which interlace martensitic structures α′ and acicular α structures, are observed in weld zone. The fracture mode is ductile fracture.

Bulging Performance and Quality Control of Aluminum Alloy Tailor-welded Overlapping Sheets Based on Interface Friction

In order to solve the problem of poor formability caused by different materials and properties in the process of tailor-welded sheets forming,a forming method was proposed to change the stress state of tailor-welded sheets by covering the tailor-welded sheets with better plastic properties overlapping sheets.At the same time,the interface friction effect between the overlapping and tailor-welded sheets was utilized to control the stress magnitude and further improve the formability and quality of the tailor-welded sheets.In this work,the bulging process of the tailor-welded overlapping sheets was taken as the research object.Aluminum alloy tailor-welded overlapping sheets bulging specimens were studied by a combination of finite element analysis and experimental verification.The results show that the appropriate use of interface friction between tailor-welded and overlapping sheets can improve the formability of tailor-welded sheets and control the flow of weld seam to improve the forming quality.When increasing the interface friction coefficient on the side of tailor-welded sheets with higher strength and decreasing that on the side of tailor-welded sheets with lower strength,the deformation of the tailor-welded sheets are more uniform,the offset of the weld seam is minimal,the limit bulging height is maximal,and the forming quality is optimal.

Spectral characteristics of arc plasma during laser-arc double-sided welding for aluminum alloy

In laser-arc double-sided welding, the spectral characteristics of the arc plasma are calculated and analyzed by spectroscopic diagnosis. The results show that, compared with conventional tungsten inert gas （TIG） welding, the introduction of a laser cilanges the physical characteristics of the arc plasma regardless of whether laser plasma penetration takes place, and that the influence of the laser mainly affects the near-anode region of the arc. When tile laser power is relatively low, the arc column tends to compress, and the arc spectral cilaracter- istics show no significant difference. When the arc root constricts, compared with pure TIG arc, the electron density increases by ~2.7 times and the electron temperature decreases by ~3000 K. When the arc column expands, the intensities of spectral lines of both the metal and Ar atoms are the strongest. But it is also observed that the electron density reduces, whereas there is no obvious decrease of electron temperature.

Fatigue Strength Analysis of Dissimilar Aluminum Alloy TIG Welds

The constant amplitude loading fatigue tests were carried out on the 6061/7075 aluminum alloy TIG fillet welded lap specimens in this study,and the weld seam cross-section hardness was measured.The experimental results show that most specimens mainly failed at the 7075 side weld toes even though the base material tensile strength of 7075 is higher than that of 6061.The maximum stress-strain concentration in the two finite element models is located at the 7075 side weld toe,which is basically consistent with the actual fracture location.The weld zone on the 7075 side experiences severe material softening,with a large gradient.However,the Vickers hardness value on the 6061 side negligibly changes and fluctuates around 70 HV.No obvious defects are found on the fatigue fracture,but a large number of secondary cracks appear.Cracks germinate from the weld toe and propagate in the direction of the plate thickness.Weld reinforcement has a serious impact on fatigue life.Fatigue life will decrease exponentially as the weld reinforcement increases under low stress.It is found that the notch stress method can give a better fatigue life prediction for TIG weldments,and the errors of the predicted results are within the range of two factors,while the prediction accuracy decreases under low stress.The equivalent structural stress method can also be used for fatigue life prediction of TIG weldments,but the errors of prediction results are within the range of three factors,and the accuracy decreases under high stress.

A Novel Model for Describing Rail Weld Irregularities and Predicting Wheel-Rail Forces Using a Machine Learning Approach

Rail weld irregularities are one of the primary excitation sources for vehicle-track interaction dynamics in modern high-speed railways.They can cause significant wheel-rail dynamic interactions,leading to wheel-rail noise,component damage,and deterioration.Few researchers have employed the vehicle-track interaction dynamic model to study the dynamic interactions between wheel and rail induced by rail weld geometry irregularities.However,the cosine wave model used to simulate rail weld irregularities mainly focuses on the maximum value and neglects the geometric shape.In this study,novel theoretical models were developed for three categories of rail weld irregularities,based on measurements of the high-speed railway from Beijing to Shanghai.The vertical dynamic forces in the time and frequency domains were compared under different running speeds.These forces generated by the rail weld irregularities that were measured and modeled,respectively,were compared to validate the accuracy of the proposed model.Finally,based on the numerical study,the impact force due to rail weld irrregularity is modeled using an Artificial Neural Network(ANN),and the optimum combination of parameters for this model is found.The results showed that the proposed model provided a more accurate wheel/rail dynamic evaluation caused by rail weld irregularities than that established in the literature.The ANN model used in this paper can effectively predict the impact force due to rail weld irrregularity while reducing the computation time.

Microstructure characteristics and corrosion behavior of metal inert gas welded dissimilar joints of 6005A modified by Sc and 5083 alloys

The corrosion behavior and microstructure characteristics of metal inert gas(MIG)welded dissimilar joints of the 6005A alloy modified with Sc(designated as 6005A+Sc)and the 5083 alloy were investigated using corrosion tests and microscopy techniques.Results show that the dissimilar joints exhibit strong stress corrosion cracking(SCC)resistance,maintaining substantial strength during slow strain rate tensile tests.Notably,the heat-affected zone(HAZ)and base metal(BM)on the 6005A+Sc side show superior performance in terms of inter-granular corrosion(IGC)and exfoliation corrosion(EXCO)compared to the corresponding zones on the 5083 side.The lower corrosion resistance of the 5083-BM and the 5083-HAZ can be attributed to the presence of numerous Al_(2)Mg_(3)phases and micro-scaled Al_(6)(Mn,Fe)intermetallics,mainly distributed along the rolling direction.Conversely,the enhanced corrosion resistance of the 6005A+Sc-BM and the 6005A+Sc-HAZ can be attributed to the discontinuously distributed grain boundary precipitates(β-Mg_(2)Si),the smaller grain size,and the reduced corrosive current density.

Microstructure and toughness of thick-gauge pipeline steel joint via double-sided friction stir welding combined with preheating

Fusion welding easily causes microstructural coarsening in the heat-affected zone(HAZ) of a thick-gauge pipeline steel joint. This is most significant in the inter-critically coarse-grained HAZ(ICCGHAZ), which considerably deteriorates the toughness of the joint. In the present work, 11-mm thick pipeline steel was joined by preheating and double-sided friction stir welding(FSW). A comparative study on the microstructure and toughness in the ICCGHAZs for FSW and gas metal arc welding(GMAW) was performed. The toughness in the ICCGHAZ for FSW was improved significantly than that in the ICCGHAZ for GMAW. Generally, the nugget zone(NZ) has a coarse microstructure in the FSW steel joint formed at the highest peak temperature. However, in the current study, the microstructure in the one-pass NZ was remarkably refined owing to the static recrystallization of ferrite. An excellent toughness was achieved in the NZ of the pipeline steel joint that employed FSW.

Microstructure evolution along thickness in double-side friction stir welded 7085 Al alloy

The microstructure evolution in the weld zone of double-side friction stir welded（DS-FSWed） 7085-T7452 Al alloy was investigated by the electron backscatter diffraction method.The results indicate that DS-FSW process results in substantial grain refinement.The misorientation angle distribution shows a very high volume fraction of high angle grain boundary（HAGB）（above 75%） under DS-FSW condition at rotational rate of 300 r/min.The fraction of HAGB rapidly decreases with increasing the rotational rate from 300 to 950 r/min,and the obvious growth of grain in the weld nugget zone（WNZ） is presented.The average grain sizes in the elongated grains of thermal-mechanical affected zone（TMAZ） and partially equiaxed and coarser grains of thermal affected zone（HAZ） are 7.3 and 15.7 μm with the fractions of HAGBs less than 43% and 30%,respectively.The intensities of（100）,（110） and（111） pole figures in the WNZ obviously decrease when compared with those in the BM and present significantly difference along the thickness direction of plate.

Study on heat efficiency of laser-TIG double-side welding

A series of laser-TIG double-side welding experiments for aluminum alloys were carried out to investigate the heat efficiency of the process. The melting efficiency was introduced to evaluate quantitatively the degree of the mutual effect of the laser and the arc. The results showed that the melting efficiency of laser-TIG double-side welding exceeded the sum of the laser and the arc taken separately. With the increase of heat input, the weld depth and melting efficiency of the laser and the arc were increased signifwantly. This, in fact, implies the strong mutual effect of the laser and the arc as heat sources joined simultaneously in the process. Comparatively, the higher efficiency of the laser constituent of heat sources plays the main role in the increase of the process efficiency. The phenomena of arc column convergence, increased laser absorptivity and the formation of heat accumulation region are the causes of the improvement of heat efficiency.

Characterization of CIAE developed double-sided silicon strip detector for charged particles

A double-sided silicon strip detector(DSSD)with active area of 48 mm x 48 mm and thickness of300μm has been developed. Each side of DSSD consists of48 strips, each with width of 0.9 mm and inter-strip separation of 0.1 mm. Electrical properties and detection performances including full depletion bias voltage, reverse leakage current, rise time, energy resolution and cross talk have been studied. At a bias of 80 V, leakage current in each strip is less than 15 nA, and rise time for alpha particle at 5157 keV is approximately 15 ns on both sides.Good energy resolutions have been achieved with0.65-0.80% for the junction strips and 0.85-1.00% for the ohmic strips. The cross talk is found to be negligible on both sides. The overall good performance of DSSD indicates its readiness for various nuclear physics experiments.

Nonlinear optical properties in double-sided nonlinear media with Z-scan technique based on the Huygens-Fresnel principle

We present a theoretical model to analyse the propagation of a Gaussian laser beam through double-sided nonlinear media. This model is based on the Huygens-Fresnel diffraction integral method. This theoretical model is not only consistent with the cascade structure model for a small nonlinear phase-shift but also can be used for a large nonlinear phase-shift. It has been verified that it is suitable to characterize the double-sided nonlinear media compared with the cascade structure model. A good agreement between the experimental data and the results from the theoretical model is obtained. It will be useful for the design of multi-sided nonlinear materials.