Variation in the surface heat flux on the north and south slopes of Mount Qomolangma

The distinctive conditions present on the north and south slopes of Mount Qomolangma,along with the intricate variations in the underlying surfaces,result in notable variations in the surface energy flux patterns of the two slopes.In this paper,data from TESEBS(Topographical Enhanced Surface Energy Balance System),remote sensing data from eight cloud-free scenarios,and observational data from nine stations are utilized to examine the fluctuations in the surface heat flux on both slopes.The inclusion of MCD43A3 satellite data enhances the surface albedo,contributing to more accurate simulation outcomes.The model results are validated using observational data.The RMSEs of the net radiation,ground heat,sensible heat,and latent heat flux are 40.73,17.09,33.26,and 30.91 W m^(−2),respectively.The net radiation flux is greater on the south slope and exhibits a rapid decline from summer to autumn.Due to the influence of the monsoon,on the north slope,the maximum sensible heat flux occurs in the pre-monsoon period in summer and the maximum latent heat flux occurs during the monsoon.The south slope experiences the highest latent heat flux in summer.The dominant flux on the north slope is sensible heat,while it is latent heat on the south slope.The seasonal variations in the ground heat flux are more pronounced on the south slope than on the north slope.Except in summer,the ground heat flux on the north slope surpasses that on the south slope.

Impact of Cattaneo-Christov Heat Flux in the Nanofluid Flow over an Inclined Permeable Surface with Irreversibility Analysis

This study discusses the magnetohydrodynamic nanofluid flow over an inclined permeable surface influenced by mixed convection, and Cattaeo-Christov heat flux. The heat transfer analysis is performed in the presence of a heat source/sink and thermal stratification. To gauge the energy loss during the process, an irreversibility analysis is also performed. A numerical solution to the envisaged problem is obtained using the bvp4c package of MATLAB. Graphs are drawn to assess the consequences of the arising parameters against the associated profiles. The results show that an augmentation in the magnetic field and nanomaterial volume fraction results in an enhancement in the temperature profile. A strong magnetic field can significantly reduce the fluid velocity. The behavior of the Skin friction coefficient against the different estimates of emerging parameters is discussed. .

Relationships between the surface quality of a single crystal copper ingot and the process parameters of a heated mould continuous casting method

The relationships between the surface quality of a single crystal copper ingot and the process parameters of heated mould continuous casting method were studied experimentally using our own design of horizontal heated mould continuous casting apparatus, and the mechanism by which process parameters affect the surface quality of a single crystal copper ingot is analyzed in the present paper. The results show that the process parameters affect the surface quality of a pure copper ingot by affecting the position of the liquid-solid interface in the mould. The position of the liquid-solid interface in the mould must be controlled carefully within an appropriate range, which is determined through a series of experiments, in order to gain a single crystal copper ingot with good surface quality.

Transient analysis on surface heated piezoelectric semiconductor plate lying on rigid substrate

Based on the thermo-electro-elastic coupling theory,the mathematical model for a surface heated piezoelectric semiconductor(PS)plate is developed in the time domain.Applying the direct and inverse Laplace transformations to the established model,the mechanical and electrical responses are investigated.The comparison between the analytical solution and the finite element method(FEM)is conducted,which illustrates the validity of the derivation.The calculated results show that the maximum values of the mechanical and electrical fields appear at the heating surface.Importantly,the perturbation carriers tend to concentrate in the zone near the heating surface under the given boundary conditions.It can also be observed that the heating induced elastic wave leads to jumps for the electric potential and perturbation carrier density at the wavefront.When the thermal relaxation time is introduced,all the field quantities become smaller because of the thermal lagging effect.Meanwhile,it can be found that the thermal relaxation time can describe the smooth variation at the jump position.Besides,for a plate with P-N junction,the effect of the interface position on the electrical response is studied.The effects of the initial carrier density on the electrical properties are discussed in detail.The conclusions in this article can be the guidance for the design of PS devices serving in thermal environment.

Exploration of regional surface average heat flow from meteorological and geothermal series

We attempt to compute the Surface Average Heat Flow （SAHF） from long-term temperature observations of one hundred seventy-seven observational points at the depths of 0.8, 1.6, and 3.2 m, which were relatively evenly distributed in China's Mainland. We first employ Fourier transformation to remove the influence of atmospheric temperature variations from the observation series, which are classified into the type of the steady-state temperature monotonously increasing with depth （type I） and other three types. Then we compare our results obtained from the data of type I, of which the values are thought to equal to those of the mean borehole heat flow, with those obtained from traditional heat flow observations mainly distributed in North China Craton. In computations of the SAHF at the observation stations, we deduce the thermal diffusivity and volumetric specific heat of the soil by employing harmonic solutions of the heat conduction equation for the same moisture group as the first step, and then we determine the SAHF using Fourier＇s law. Our results indicate that the SAHF derived from shallow earth geothermal data can reflect the heat flow field to a large extent.

Effects of Steam Heat Treatment on the Surface Contact Angle of Chinese Fir

The aim of this study was investigate the effects of heat treatment on the contact angle of Chinese fir, and the indicators affecting the change of contact an-gle change. It was determined that the duration of treatment had significant effect on the change curves of contact angle of Chinese fir wood due to the change curves of contact angle became more centralized and orderly after the specimens heat treated at 180 ℃. Compared with the untreated wood, the contact angle in-creased from 51＆#176; to 124＆#176; after 4 h treatment, and hydroxyl absorbance of hy-drophilic functional groups decreased from 2.08 to 1.63, while carbonyl absorbance from 0.92 to 0.62. The surface roughness has not significant influence on the con-tact angle. Heat treatment of the Chinese fir caused surface morphological change, which produced hol owed-out phenomenon. The increased surface contact angle caused by heat treatment can be used for outdoor and sauna facilities.

Impact of Surface Sensible Heating over the Tibetan Plateau on the Western Pacific Subtropical High: A Land–Air–Sea Interaction Perspective

The impact of surface sensible heating over the Tibetan Plateau （SHTP） on the western Pacific subtropical high （WPSH） with and without air-sea interaction was investigated in this study. Data analysis indicated that SHTP acts as a relatively independent factor in modulating the WPSH anomaly compared with ENSO events. Stronger spring SHTP is usually fol- lowed by an enhanced and westward extension of the WPSH in summer, and vice versa. Numerical experiments using both an AGCM and a CGCM confirmed that SHTP influences the large-scale circulation anomaly over the Pacific, which features a barotropic anticyclonic response over the northwestern Pacific and a cyclonic response to the south. Owing to different background circulation in spring and summer, such a response facilitates a subdued WPSH in spring but an en- hanced WPSH in summer. Moreover, the CGCM results showed that the equatorial low-level westerly at the south edge of the cyclonic anomaly brings about a warm SST anomaly （SSTA） in the equatorial central Pacific via surface warm advection. Subsequently, an atmospheric Rossby wave is stimulated to the northwest of the warm SSTA, which in turn enhances the at- mospheric dipole anomalies over the western Pacific. Therefore, the air-sea feedbacks involved tend to reinforce the effect of SHTP on the WPSH anomaly, and the role of SHTP on general circulation needs to be considered in a land-air-sea interaction framework.

Parameterization of Heat Fluxes at Heterogeneous Surfaces by Integrating Satellite Measurements with Surface Layer and Atmospheric Boundary Layer Observations

The regional heat flux exchange between heterogeneous landscapes and the nearby surface layer （SL） is a key issue in the study of land-atmosphere interactions over arid areas such as the Heihe River basin in northwestern China and in high elevation areas such as the Tibetan Plateau. Based on analysis of the land surface heterogeneity and its effects on the overlying air flow, the use of SL observations, atmospheric boundary layer （ABL） observations, and satellite remote sensing （RS） measurements along with three parameterization methodologies （here, termed as the RS, tile, and blending approaches） have been proposed to estimate the surface heat flux densities over heterogeneous landscapes. The tile and blending approaches have also been implemented during HEIhe basin Field Experiment （HEIFE）, the Coordinated Enhanced Observing Period （CEOP） Asia-Australia Monsoon Project on the Tibetan Plateau （CAMP/Tibet）, the Arid Environment Comprehensive Monitoring Plan ＇95 （AECMP＇95）, and the DunHuang Experiment （DHEX）. The results showed that these two proposed parameterization methodologies can be accurately used over heterogeneous land surfaces.

The Effects of Anomalous Snow Cover of the Tibetan Plateau on the Surface Heating

On the basis of snow data and AWS (Automatic Weather Station) data obtained from the Tibetan Plateau in recent years (1993 to 1999), the features of sensible heat, latent heat and net long-wave radiations are estimated, and their variations in more-snow year (1997/ 1998) and less-snow year (1996/ 1997) are analyzed comparatively. The relationships between snow cover of the Tibetan Plateau and plateau’s surface heating to the atmospheric heating are also discussed. The difference between more-snow and less-snow year in spring is remarkably larger than that in winter. Therefore, the effect of anomalous snow cover of the Tibetan Plateau in winter on the plateau heating appears more clearly in the following spring of anomalous snow cover. Key words Tibetan Plateau - Snow cover - Effects - Surface heat fluxes This research was supported by the National Key Programme for Developing Basic Sciences G1998040900 (I), National Natural Science Foundation of China (40075018) and Sichuan Youth Science and Technology Fund.

An Assessment of the Quality of Surface Sensible Heat Flux Derived from Reanalysis Data through Comparison with Station Observations in Northwest China

The present study compares seasonal and interdecadal variations in surface sensible heat flux over Northwest China between station observations and ERA-40 and NCEP-NCAR reanalysis data for the period 1960-2000. While the seasonal variation in sensible heat flux is found to be consistent between station observations and the two reanalysis datasets, both land-air temperatures difference and surface wind speed show remarkable systematic differences. The sensible heat flux displays obvious interdecadal variability that is season-dependent. In the ERA-40 data, the sensible heat flux in spring, fall, and winter shows interdecadal variations that are similar to observations. In the NCEP-NCAR reanalysis data, sensible heat flux variations are inconsistent with and sometimes even opposite to observations. While surface wind speeds from the NCEP-NCAR reanalysis data show interdecadal changes consistent with station observations, variations in land-air temperature difference differ greatly from the observed dataset. In terms of land-air temperature difference and surface wind speed, almost no consistency with observations can be identified in the ERA-40 data, apart from the land-air temperature difference in fall and winter. These inconsistencies pose a major obstacle to the application in climate studies of surface sensible heat flux derived from reanalysis data.

Estimation of ground heat flux and its impact on the surface energy budget for a semi-arid grassland

Three approaches, i.e., the harmonic analysis （HA） technique, the thermal diffusion equation and correction （TDEC） method, and the calorimetric method used to estimate ground heat flux, are evaluated by using observations from the Semi-Arid Climate and Environment Observatory of Lanzhou University （SACOL） in July, 2008. The calorimetric method, which involves soil heat flux measurement with an HFP01SC self-calibrating heat flux plate buried at a depth of 5 cm and heat storage in the soil between the plate and the surface, is here called the ITHP approach. The results show good linear relationships between the soil heat fluxes measured with the HFP01SC heat flux plate and those calculated with the HA technique and the TDEC method, respectively, at a depth of 5 cm. The soil heat fluxes calculated with the latter two methods well follow the phase measured with the HFP01SC heat flux plate. The magnitudes of the soil heat flux calculated with the HA technique and the TDEC method are close to each other, and they are about 2 percent and 6 percent larger than the measured soil heat flux, respectively, which mainly occur during the nighttime. Moreover, the ground heat fluxes calculated with the TDEC method and the HA technique are highly correlated with each other （R2= 0.97）, and their difference is only about 1 percent. The TDEC-calculated ground heat flux also has a good linear relationship with the ITttP-calculated ground heat flux （R2 = 0.99）, but their difference is larger （about 9 percent）. Furthermore, compared to the HFP01SC direct measurements at a depth of 5 cm, the ground heat flux calculated with the HA technique, the TDEC method, and the ITHP approach can improve the surface energy budget closure by about 6 percent, 7 percent, and 6 percent at SACOL site, respectively. Therefore, the contribution of ground heat flux to the surface energy budget is very important for the semi-arid grassland over the Loess Plateau in China. Using turbulent heat fluxes with common corrections, soil heat storage between the surface and the heat flux plate can improve the surface energy budget closure by about 6 to 7 percent, resulting in a closure of 82 to 83 percent at the SACOL site.

The Regional Surface Heating Field over the Heterogeneous Landscape of the Tibetan Plateau Using MODIS and In Situ Data

In this study, a parameterization scheme based on Moderate Resolution Imaging Spectroradiometer （MODIS） data and in-situ data was tested for deriving the regional surface heating field over a heterogeneous landscape. As a case study, the methodology was applied to the whole Tibetan Plateau （TP） area. Four images of MODIS data （i.e., 30 January 2007, 15 April 2007, 1 August 2007, and 25 October 2007） were used in this study for comparison among winter, spring, summer, and autumn. The results were validated using the observations measured at the stations of the Tibetan Observation and Research Platform （TORP）. The results show the following： （1） The derived surface heating field for the TP area was in good accord with the land-surface status, showing a wide range of values due to the strong contrast of surface features in the area. （2） The derived surface heating field for the TP was very close to the field measurements （observations）. The APD （absolute percent difference） between the derived results and the field observations was 〈10%. （3） The mean surface heating field over the TP increased from January to April to August, and decreased in October. Therefore, the reasonable regional distribution of the surface heating field over a heterogeneous landscape can be obtained using this methodology. The limitations and further improvement of this method are also discussed.

Remote Sensing Parameterization of Land Surface Heat Fluxes over Arid and Semi-arid Areas

Dealing with the regional land surfaces heat fluxes over inhomogeneous land surfaces in arid and semi-arid areas is an important but not an easy issue. In this study, one parameterization method based on satellite remote sensing and field observations is proposed and tested for deriving the regional land surface heat fluxes over inhomogeneous landscapes. As a case study, the method is applied to the Dunhuang experimental area and the HEIFE (Heihe River Field Experiment, 1988-1994) area. The Dunhuang area is selected as a basic experimental area for the Chinese National Key Programme for Developing Basic Sciences: Research on the Formation Mechanism and Prediction Theory of Severe Climate Disaster in China (G1998040900, 1999-2003). The four scenes of Landsat TM data used in this study are 3 June 2000, 22 August 2000, and 29 January 2001 for the Dunhuang area and 9 July 1991 for the HEIFE area. The regional distributions of land surface variables, vegetation variables, and heat fluxes over inhomogeneous landscapes in arid and semi-arid areas are obtained in this study.

Connections between Surface Sensible Heat Net Flux and Regional Summer Precipitation over China

Using the observed monthly precipitation and NCEP (National Centers for Environmental Prediction) reanalysis surface ?ux data from 1951–2000, the connections between the seasonal SSHNF (Surface Sensible Heat Net Flux) over the Asian continent and the regional summer precipitation of China were examined. The patterns of collective and individual correlations were identi?ed. The results indicate that the response of the regional summer precipitation of China to the seasonal SSHNF over the study area varies according to region and season. The interannual variability of summer precipitation anomalies over Xinjiang, the northernmost Northeast China, and the North China Plain are most sensitive to the anomaly of the seasonal SSHNF. There are signi?cant collective correlations between the interannual anomalies of the seasonal SSHNF and summer precipitation over these regions. In contrast, the Southeast Tibetan Plateau, Huaihe River Valley, and surrounding areas exhibit the least signi?cant correlation. Signi?cant individual correlations exist between the summer precipitation over the southernmost Northeast China, East Inner Mongolia, South of the Yangtze River and South China and the seasonal SSHNF in certain seasons over the following areas: near Lake Baikal and Lake Balkhash, near Da Hinggan Mountains and Xiao Hinggan Mountains, as well as the Tibetan Plateau.

Surface latent heat flux anomalies preceding inland earthquakes in China

Using data from the National Center for Environmental Prediction （NCEP）, the paper analyzed the surface latent heat flux （SLHF） variations for five inland earthquakes occurred in some lake area, moist area and arid area of China during recent years. We used the SLHF daily and monthly data to differentiate the global and seasonal variability from the transient local anomalies. The temporal scale of the observed variations is 1-2 months before and after the earthquakes, and spatial scale is about 10°×10°. The result suggests that the SLHFs adjacent the epicenters all are anomalous high value （〉μ＋2σ） 8-30 days before the shocks as compared with past several years of data. Different from the abnormal meteorological phenomenon, the distribution of the anomalies was isolated and local, which usually occurred in the epicenter and its adjacent area, or along the fault lines. The increase of SLHF was tightly related with the season which the earthquake occurs in; the maximal （125 W/m^2, Pu＇er earthquake） and minimal （25 W/m^2, Gaize earthquake） anomalies were in summer and winter, respectively. The abundant surface water and groundwater in the epicenter and its adjacent region can provide necessary condition for the change of SLHF. To further confirm the reliability of SLHF anomaly, it is necessary to explore its physical mechanism in depth by more earthquake cases.

Influence of Late Springtime Surface Sensible Heat Flux Anomalies over the Tibetan and Iranian Plateaus on the Location of the South Asian High in Early Summer

Variation in the location of the South Asian High （SAH） in early boreal summer is strongly influenced by elevated surface heating from the Tibetan Plateau （TP） and the Iranian Plateau （IP）. Based on observational and ERA-Interim data, diagnostic analyses reveal that the interannual northwestward-southeastwaxd （NW-SE） shift of the SAH in June is more closely correlated with the synergistic effect of concurrent surface thermal anomalies over the TP and IP than with each single surface thermal anomaly over either plateau from the preceding May. Concurrent surface thermal anomalies over these two plateaus in May are characterized by a negative correlation between sensible heat flux over most parts of the TP （TPSH） and IP （IPSH）. This anomaly pattern can persist till June and influences the NW-SE shift of the SAH in June through the release of latent heat （LH） over northeastern India. When the IPSH is stronger （weaker） and the TPSH is weaker （stronger） than normal in May, an anomalous cyclone （anticyclone） appears over northern India at 850 hPa, which is accompanied by the ascent （descent） of air and anomalous convergence （divergence） of moisture flux in May and June. Therefore, the LH release over northeastern India is strengthened （weakened） and the vertical gradient of apparent heat source is decreased （increased） in the upper troposphere, which is responsible for the northwestward （southeastward） shift of the SAH in June.

Seasonal evolution of the dominant modes of the Eurasian snowpack and atmospheric circulation from autumn to the subsequent spring and the associated surface heat budget

This study investigates the seasonal evolution of the dominant modes of the Eurasian snowpack and atmospheric circulation from autumn to the subsequent spring using snow water equivalent （SWE）, snow cover frequency （SCF）, and 500 hPa geopotential height data. It is found that the Eurasian SWE/SCF and circulation dominant modes are stably coupled from autumn to the subsequent spring.The temporal coherence of the seasonal evolution of the dominant modes is examined.The seasonal evolution of the Eurasian circulation and SWE dominant modes exhibit good coherence, whereas the evolution of the Eurasian SCF dominant mode is incoherent during the autumn-winter transition season. This incoherence is associated with a sign-change in the SCF anomalies in Europe during the autumn-winter transition season, which is related to the wind anomalies over Europe. In addition, the surface heat budget associated with the Eurasian SWE/SCF and circulation dominant modes is analyzed. The sensible heat flux （SHF） related to the wind-induced thermal advection dominates the surface heat budget from autumn to the subsequent spring, with the largest effect during winter. The surface net shortwave radiation is mainly modulated by snow cover rather than cloud cover, which is estimated to be as important as, or likely superior to, the SHF for the surface heat budget during spring.The NCEP-NCAR surface heat flux reanalysis data demonstrate a consistency with the SWE/SCF and air temperature observational data, indicating a good capability for snow-atmosphere interaction analysis.

Influence of heating rate on reactivity and surface chemistry of chars derived from pyrolysis of two Chinese low rank coals

A series of char samples were derived from pyrolysis of two typical low-rank coals in China （Shengli lig- nite and Shenmu bituminous coal） at low, medium and fast heating rates, respectively, to the same pyrol- ysis temperature 750℃. Then these chars were characterized by means of thermogravimetric analysis and Fourier transform infrared spectrometer with the aim to investigate the influence of heating rate in pyrolysis process on gasification reactivity and surface chemistry of them. Besides, a homogeneous model was used to quantitatively analyze the activation energy of gasification reaction. The results reveal that Shengli lignite and its derived chars behave higher gasification reactivity and have less content of oxygen functional groups than Shenmu coal and chars. Meanwhile, chars derived from Shengli lignite at 50℃/min and Shenmu coal at 200℃/min have the greatest gasification reactivity, respectively. The oxygen functional groups in Shengli lignite are easily thermo-decomposed, and they are less affected by the heating rate, while that in Shenmu coal have a significant change with the variation of heating rate. In addition, there is no good correlation between the change of oxygen functional groups and that of the gasification reactivity of the derived chars from pyrolysis at different heating rates.

Computation of synthetic surface heat transfer coefficient of 7B50 ultra-high-strength aluminum alloy during spray quenching

According to inverse heat transfer theory, the evolutions of synthetic surface heat transfer coefficient（SSHTC） of the quenching surface of 7B50 alloy during water-spray quenching were simulated by the Pro CAST software based on accurate cooling curves measured by the modified Jominy specimen and temperature-dependent thermo-physical properties of 7 B50 alloy calculated using the JMat Pro software. Results show that the average cooling rate at 6 mm from the quenching surface and 420-230 ℃（quench sensitive temperature range） is 45.78℃/s. The peak-value of the SSHTC is 69 kW/（m^2·K） obtained at spray quenching for 0.4 s and the corresponding temperature of the quenching surface is 160 ℃. In the initial stage of spray quenching, the phenomenon called ＂temperature plateau＂ appears on the cooling curve of the quenching surface. The temperature range of this plateau is 160-170℃ with the duration about 3 s. During the temperature plateau, heat transfer mechanism of the quenching surface transforms from nucleate boiling regime to single-phase convective regime.

Natural convection of nanofluid over vertical plate embedded in porous medium: prescribed surface heat flux

The aim of the present paper is to analyze the natural convection heat and mass transfer of nanofluids over a vertical plate embedded in a saturated Darcy porous medium subjected to surface heat and nanoparticle fluxes. To carry out the numerical solution, two steps are performed. The governing partial differential equations are firstly simplified into a set of highly coupled nonlinear ordinary differential equations by appropriate similarity variables, and then numerically solved by the finite difference method. The obtained similarity solution depends on four non-dimensional parameters, i.e., the Brownian motion parameter （Nb）, the buoyancy ratio （Nr）, the thermophoresis parameter （Nt）, and the Lewis number （Le）. The variations of the reduced Nusselt number and the reduced Sherwood number with Nb and Nt for various values of Le and Nr are discussed in detail. Simulation results depict that the increase in Nb, Nt, or Nr decreases the reduced Nusselt number. An increase in the Lewis number increases both of the reduced Nusselt number and the Sherwood number. The results also reveal that the nanoparticle concentration boundary layer thickness is much thinner than those of the thermal and hydrodynamic boundary layers.