Effect of microstructure on outer surface roughening of magnesium alloy tubes in die-less mandrel drawing

The crystal orientation and outer surface roughening of magnesium alloy tubes were evaluated to clarify the effect of the mandrel on the microstructure and outer surface roughness in die-less mandrel drawing. Locally heated ZM21 tubes with an outer diameter of 6.0 mm and an inner diameter of 3.8 mm were drawn with and without a mandrel. The outer surface roughness and crystal orientation were evaluated in the same measurement area. The results indicated that the outer surface becomes rougher in the die-less mandrel drawing than in die-less drawing for a given outer circumferential strain. The outer surface roughness developed when there was large difference in the pyramidal slip system Schmid factor. Therefore, the slip deformation of the pyramidal slip system seems to be mainly responsible for the outer surface roughening in the die-less mandrel drawing. Furthermore, the crystal grain with the {2110} crystal plane vertical to the normal direction of outer surface had a larger Schmid factor than the other crystal grains. The large number of crystal grains with the {2110} crystal plane in the die-less mandrel drawing is one of the reasons that the outer surface roughness develops more in the die-less mandrel drawing than in die-less drawing for a given outer circumferential strain. These results will contribute significantly to the development of fabrication process of the microtube with high surface quality, which prevents rapid corrosion of biomedical applications.

Drawing soldiers out of post-traumatic stress disorder

Art therapies are a broad suite of treatments including drawing, painting and music that can facilitate non-verbal communication through artistic expression. They have been used as adjunctive therapies for a range of mental health conditions. Significant numbers of returning military personnel experience post-traumatic stress disorder(PTSD), and discontinuation of care is a concern. Using drawing-based art therapy as an adjuvant to classical therapies may provide a benefit for such military patients.

Mouse-Sensitive Following Path Suggestion for Drawing Travel Routes in Web Map Systems

This paper proposes a web map system for drawing an arbitrary travel route using a mouse-sensitive following path suggestion. The interaction model of the system allows users to intuitively understand the sequence of user actions needed to draw a conceived route and reduces the number of user actions required. Moreover, the system allows users to understand at a glance several drawing alternatives (static suggestion) and also consider a particular drawing alternative (dynamic suggestion) without making any commitment. The proposed architecture of the system reduces the influence caused by communication delay between a map server and a web client by delivering in advance road network data from a map server to a web client. Experimental evaluations on a prototype we developed demonstrated that the proposed system enables users to draw arbitrary routes within noticeably less clicks, in less time, and with less stress than previous systems.

Effect of wire diameter compression ratio on drawing deformation of micro copper wire

A crystal plasticity finite element model was developed for the drawing deformation of pure copper micro wire,based on rate-dependent crystal plasticity theory.The impact of wire diameter compression ratio on the micro-mechanical deformation behavior during the wire drawing process was investigated.Results indicate that the internal deformation and slip of the drawn wire are unevenly distributed,forming distinct slip and non-slip zones.Additionally,horizontal strain concentration bands develop within the drawn wire.As the wire diameter compression ratio increases,the strength of the slip systems and the extent of slip zones inside the deformation zone also increase.However,the fluctuating stress state,induced by contact pressure and frictional stress,results in a rough and uneven wire surface and diminishes the stability of the drawing process.

Modeling asymmetric fracture mechanics of Mg alloy wire in drawing process

In this study,a numerical analysis was conducted on the ductile fracture of a 2-mm diameter Mg-1Zn-0.5Mn-0.5Sr-0.1Ca alloy wire during drawing.The hexagonally close-packed crystal structure of Mg alloys causes asymmetric fracture behavior,especially in the compression region.The aim of this study is to develop a comprehensive damage model for Mg alloy wire that accurately predicts ductile fracture,with a focus on the compression region.A novel experimental method was introduced to measure the ductile fracture of Mg alloy wires under different stress states.The wire drawing process was simulated using the Generalized Incremental Stress-State dependent damage(GISSMO)Model and the Semi-Analytical Model for Polymers(SAMP)model.The damage model's prediction and the experimental results were found to be in excellent agreement,especially in determining crack initiation.Computational analysis established a safe zone diagram for die angle and reduction ratio,and experimental validation confirmed the feasibility of this approach.The proposed damage model can provide a practical and reliable analysis for optimizing the drawing process of Mg alloy wire.

Microstructure and texture of commercially pure titanium in cold deep drawing

The development of microstructure and texture during cold deep drawing of commercially pure titanium（CP-Ti） was investigated.Three parts,stretching region,drawing region and flange region,were sequentially formed in the deep drawing process of the hemispheric surface part,with reference to deformation modes and strain regimes.Results show that the plastic strain is accommodated by dislocation slip and deformation twinning in the whole deep drawing process.The texture of the CP-Ti sheet and its drawn part consists of rolling texture component and recrystallization texture component.The intensity and type of the initial texture varied during the drawing process are related to the production of deformation twinning and dislocation slip.Twinning weakens the initial texture by randomizing the orientations of crystals,especially for the recrystallization texture.The recrystallization texture in the drawing region disappears due to the significant forming of twinning.Furthermore,over drawing would result in the predominance of dislocation slip and the texture is strengthened.

Texture evolution and its simulation of cold drawing copper wires produced by continuous casting

The texture evolution of cold drawing copper wires produced by continuous casting was measured by X-ray diffractometry and electron back-scatter diffractometry,and was simulated using Taylor model.The results show that in the drawn poly-crystal copper wires produced by traditional continuous casting,111 and 100 duplex fiber texture forms,and with increasing strain,the intensities of 111 and 100 increase.In the drawn single-crystal copper wires produced by Ohno continuous casting,100 rotates to 111,and there is inhomogeneous distribution of fiber texture along radial direction of the wires,which is caused by the distribution of shear deformation.Compared with 100,111 fiber texture is more stable in the drawn copper wires.Comparison of the experimental results with the simulated results shows that the simulation by Taylor model can analyze the texture evolution of drawn copper wires.

Influence of drawing process parameters on forming of micro copper tube with straight grooves

Using high-speed oil-filled spinning method,high quality micro copper tube with straight grooves（MCTSG） with an outer diameter of 6 mm was obtained.Then,MCTSG with an outer diameter of 3-6 mm was fabricated successfully by multi-pass drawing processing method.The influence of drawing parameters on the forming of micro straight grooves was investigated based on the forming mechanism.The results show that the values of groove depth and width decrease,while the wall thickness increases as the drawing diameter decreases.At the same time,the groove depth and width increase,while the wall thickness decreases as the die angle increases.The drawing force increases as the reduction increases.Excessive copper tube reduction may results in groove folding and segmental teeth.The drawing force decreases firstly and then increases with the increases in die angle.When the die angle α is 16°,the drawing force is the smallest,indicating 16° is the optimal angle.

Effect of electropulsing on deformation behavior of Ti-6Al-4V alloy during cold drawing

Electron backscattered diffraction （EBSD） and transmission electron microscopy （TEM） were used to investigate effect of electropulsing on microstructure and texture evolution of Ti-6Al-4V during cold drawing. Research results demonstrate that the electropulsing treatment （EPT） can enhance the deformability of the grains with unfavorable orientations, which makes the compatibility of deformation among grains much better. A comparison in texture evolution between conventional cold drawing and EPT cold drawing indicates that the EPT promotes prismatic 〈a〉 slip moving, restricts pyramidal 〈c＋a〉 slip occurring and accommodates the deformation with c-component by grain boundary sliding. The fraction decrease of low-angle grain boundaries for samples deformed with EPT reveals that the application of electropulsing restricts the formation of the incidental dislocation boundaries and the geometrically necessary boundaries.

Effects of stress state on texture and microstructure in cold drawing-bulging of CP-Ti sheet

Three different stress states of the combination of tensile（t） stress and compressive（c） stress,t t,t c and t c c,exist in the deformed commercially pure titanium（CP-Ti） sheet during cold drawing-bulging.The textures and microstructures in the different stress state regions were investigated by means of XRD and TEM analysis.Similar development of texture and microstructure is achieved with less thickness strain under multiaxial stresses in drawing-bulging than in cold rolling.The results show that texture and microstructure are much sensitive to multiaxial stresses.Twinning is more easily activated under compressive stress than tensile stress.Prism a slip is heavily affected by tensile stress,resulting in a remarkable change of the intensity of（0°,35°,0°） texture,while pyramidal c＋a slip,forming（20°,35°,30°） texture,weakens with the increase of thickness strain in spite of stress state.

Application of ultra-smooth composite diamond film coated WC-Co drawing dies under water-lubricating conditions

A specific revised HFCVD apparatus and a novel process combining HFCVD and polishing technique were presented to deposit the micro-and nano-crystalline multilayered ultra-smooth diamond（USCD） film on the interior-hole surface of WC-Co drawing dies with aperture ranging from d1.0 mm to 60 mm.Characterization results indicate that the surface roughness values（Ra） in the entry zone,drawing zone and bearing zone of as-fabricated USCD coated drawing die were measured as low as 25.7,23.3 and 25.5 nm,respectively.Furthermore,the friction properties of USCD films were examined in both dry sliding and water-lubricating conditions,and the results show that the USCD film presents much superior friction properties.Its friction coefficients against ball-bearing steel,copper and silicon nitride balls（d4 mm）,is always lower than that of microcrystalline diamond（MCD） or WC-Co sample,regardless of the lubricating condition.Meanwhile,it still presents competitive wear resistance with the MCD films.Finally,the working lifetime and performance of as-fabricated USCD coated drawing dies were examined under producing low-carbon steel pipes in dry-sliding and water-lubricating conditions.Under the water-lubricating drawing condition,its production significantly increases by about 20 times compared with the conventional WC-Co drawing dies.

Flexible die drawing of magnesium alloy sheet by superimposing ultrasonic vibration

Combining solid granule medium forming technology with ultrasonic vibration plastic forming technology, ultrasonic vibration granule medium forming （UGMF） technology was proposed. To reveal the effect of ultrasonic vibration on flexible-die deep drawing, an ultrasonic vibration with a frequency of 20 kHz and a maximum output of 1.5 kW was on the solid granule medium deep drawing of AZ31B magnesium alloy sheet. The results revealed that ultrasonic vibration promotes the pressure transmission performance of the granule medium and the formability of the sheet. The forming load declines with the ultrasonic amplitude during the drawing process as a result of the combined influence of the ＂surface effect＂ and the ＂softening＂ of the ＂volume effect＂.

Effects of tribological behavior of DLC film on micro-deep drawing processes

To decrease the size effects of friction in microforming, three kinds of surface coatings, such as diamond-like carbon（DLC）, TiN and MoS2, were deposited on surfaces of dies with plasma based ion implantation and deposition（PBII D） method and magnetron sputtering technique, respectively. The tribological behavior of surface coatings was analyzed considering plastic deformation of specimen at contact interface. The analyses indicate that there is a lower coefficient of friction（COF） and a high wear resistance under the condition of large strain/stress when using the DLC film. The graphitization of DLC film occurs after 100 times of tests. The mechanism of graphitization was analyzed considering energy induced by friction work. The effects of DLC film properties on qualities of micro-deep drawn parts were investigated by analyzing the reduction of wall thickness, etc. The results indicate that DLC film is very helpful for improving the qualities of the micro-parts.

基于Visio Drawing Control控件的图形化潮流计算软件开发

针对VC,Delphi等工具开发电力系统分析计算软件图形可视化的缺陷,提出并研究了一种基于VisioDrawing Control图形控件,利用VC进行二次开发的图形化电力系统潮流计算软件开发的技术,研究了基于该控件的图形化建模方法及电网拓扑结构的自动识别,开发了实用的电力系统图形化潮流计算软件.实践表明,基于Visio Drawing Control的二次开发技术为图形化电力系统潮流计算软件的开发提供了新的有效的途径.

Graphical Simulator for Chinese Ink-Wash Drawing

Simulating the traditional painting art by computer graphics is a challenging and attractive subject. Basing on the experience in the ink wash drawing, in this paper, we expound the artistic characters of ink wash painting and particularly analyze the characteristics of the materials used in the ink wash drawing and the relationships between them. A simulation model is presented and some typical visual effects of the ink wash painting are realized.

Effect of friction coefficient in deep drawing of AA6111 sheet at elevated temperatures

The effect of friction coefficient on the deep drawing of aluminum alloy AA6111 at elevated temperatures was analyzed based on the three conditions using the finite element analysis and the experimental approach.Results indicate that the friction coefficient and lubrication position significantly influence the minimum thickness,the thickness deviation and the failure mode of the formed parts.During the hot forming process,the failure modes are draw mode,stretch mode and equi-biaxial stretch mode induced by different lubrication conditions.In terms of formability,the optimal value of friction coefficient determined in this work is 0.15.At the same time,the good agreement is performed between the experimental and simulated results.Fracture often occurs at the center of cup bottom or near the cup corner in a ductile mode or ductile-brittle mixed mode,respectively.

Analysis of elliptical cup drawing process of stainless sheet metal

Prandtl-Reuss flow rule and Hill’s yield criterion were adopted and combined with the concept of finite deformation theory, updated Lagrangian formulation, and a three-dimensional finite element analytical model was established by application of quadrilateral four-node degenerated shell elements coupling into a rigid matrix to deal with the sheet metal forming problems. The fractured thickness of a specimen obtained from a simple tension test was used to be the fracture criterion for the numerical analysis to explore the relationship between punch load and stroke, the thickness distribution, the deformation history and the forming limit of work-piece in the elliptical cup drawing process. The numerical analysis and experiment results show that the punch load increases with the increase of punch stroke, and when the load reaches its maximum, the blank continues to deform with the increase of the punch stroke, resulting in a reduced load until the extension is completed. The minimum thickness of the work-piece concentrates in the contact region of the work-piece and long axis of the punch due to the smaller radius of the curvature of the long axis than the short axis. So the blanks bore the maximum tensile stress in the long axis. Through the limit drawing ratio defined by perimeter of the elliptical punch, the limit drawing ratio of this elliptical cup drawing is defined to be 2.136.

海外项目shop drawing的理解

通过对海外项目shop drawing(细化图)的理解,阐述了shop drawing的定义以及绘制shop drawing过程中需要注意的问题。通过实例分析,为同类型国际港口工程中细化设计提供参考和借鉴。

Influence of different rolling routes on mechanical anisotropy and formability of commercially pure titanium sheet

Influence of three different rolling routes on mechanical anisotropy and formability of commercially pure titanium sheetwas investigated.Route A and Route B are unidirectional rolling(UR)where the rolling direction is along initial rolling direction(RD)and transverse direction(TD),respectively.Route C is cross rolling(CR)where the rolling direction is changed by90°aftereach rolling pass.The microstructure and texture,tensile mechanical properties including strength and elongation,and also theanisotropy of the UR and CR sheets were investigated at room temperature.The XRD results indicate that the texture intensity ofrolled samples gradually weakens from Route A to Route C.Compared with Route A and Route B rolled samples,the Route C rolledsamples show a smaller planar anisotropy.The deep drawing tests reveal that cross rolling can avoid the occurrence of earing.Erichsen tests indicate that rolling routes have an effect on stretch formability of pure titanium sheet.

EFFECTS OF SPECIFIED BLANK SIZE ON BODY WRINKLING DURING HYDRODYNAMIC DEEP DRAWING OF TAPERED RECTANGULAR BOX

In this paper, the forming features of tapered rectangular box during hydrodynamic deep drawing are studied by means of FEM.The effect rules of square blank corner corner amount on body wrinkling are recognized and corresponding methods are discussed. At last, the results of FEM are verified by experi- ment.