At present,iron and steel enterprises mainly use“after spot test ward”to control final product quality.However,it is impossible to realize on-line quality predetermining for all products by this traditional approach...At present,iron and steel enterprises mainly use“after spot test ward”to control final product quality.However,it is impossible to realize on-line quality predetermining for all products by this traditional approach,hence claims and returns often occur,resulting in major eco-nomic losses of enterprises.In order to realize the on-line quality predetermining for steel products during manufacturing process,the predic-tion models of mechanical properties based on deep learning have been proposed in this work.First,the mechanical properties of deep drawing steels were predicted by using LSTM(long short team memory),GRU(gated recurrent unit)network,and GPR(Gaussian process regression)model,and prediction accuracy and learning efficiency for different models were also discussed.Then,on-line re-learning methods for transfer learning models and model parameters were proposed.The experimental results show that not only the prediction accuracy of optimized trans-fer learning models has been improved,but also predetermining time was shortened to meet real time requirements of on-line property prede-termining.The industrial production data of interstitial-free(IF)steel was used to demonstrate that R2 value of GRU model in training stage reaches more than 0.99,and R2 value in testing stage is more than 0.96.展开更多
The implementation methods of computer aided design,drawing and drawing management for plate cuttingmachine are discussed. The system structure for plate cutting- machine design is put forward firstly, then some key t...The implementation methods of computer aided design,drawing and drawing management for plate cuttingmachine are discussed. The system structure for plate cutting- machine design is put forward firstly, then some key technologies and their implementation methods are introduced, which include the structure management of graphics, the unification of graph and design calculation, information share of part, assemble and drawing management system, and movement simulation of key components.展开更多
Based on the necessity of three dimensional modeling with computer in teaching reform, this paper is the summarization of reform practice of teaching engineering drawing in our institute. The teaching reform begins wi...Based on the necessity of three dimensional modeling with computer in teaching reform, this paper is the summarization of reform practice of teaching engineering drawing in our institute. The teaching reform begins with three dimensional modeling that used computer instead of board. On the basis of target of teaching reform, set of teaching content, arrangement of class hour and teaching method, the research of teaching practice have been done, and very good effects in teaching of engineering drawing have been achieved.展开更多
Hubei Tianmen Textile Machinery Co.,Ltd.is a well-known enterprise and key high-tech enterprise in China textile industry.The company's leading product,drawing frame,has completely independent intellectual propert...Hubei Tianmen Textile Machinery Co.,Ltd.is a well-known enterprise and key high-tech enterprise in China textile industry.The company's leading product,drawing frame,has completely independent intellectual property rights,among which TM 11 is well received by users and has a high market share in China.展开更多
The inherent teaching approach can no longer meet the demands of society.In this paper,current issues within the teaching landscape of architectural engineering technology in higher vocational colleges as well as the ...The inherent teaching approach can no longer meet the demands of society.In this paper,current issues within the teaching landscape of architectural engineering technology in higher vocational colleges as well as the policies and teaching demands that formed the basis of this model were analyzed.The study shows the importance of the implementation of the teaching model“promoting teaching and learning through competitions.”This model puts emphasis on the curriculum and teaching resources,while also integrating the teaching process and evaluation with competition.These efforts aim to drive education reform in order to better align with the objectives of vocational education personnel training,while also acting as a reference for similar courses.展开更多
In high speed wire drawing, the temperature rise is produced by the generation heat from plastic deformation of metal material and friction between wire and tool, which greatly influences the lubrication situation and...In high speed wire drawing, the temperature rise is produced by the generation heat from plastic deformation of metal material and friction between wire and tool, which greatly influences the lubrication situation and mechanical properties. During high drawing, the phenomenon that wire is embrittled and die is stuck can be formed by the notable temperature rise. In this paper, based on theory of plastic deformation work , considering friction heat generation and variable physical coefficients, the mathematical model of temperature rise of high speed drawing is established and the computer program to analogy the whole process of drawing is compiled. Also the process of wire drawing on a few of alloys are calculated theoretically. Compared the calculation value with measurement, the result shows that the theoretical value coincides with experimental data.展开更多
A computer control system for drawing machine in horizontal continuous cast set was introduced.The operation features of the drawing machine were analyzed»the hardware configuration and principles of interface ci...A computer control system for drawing machine in horizontal continuous cast set was introduced.The operation features of the drawing machine were analyzed»the hardware configuration and principles of interface circuit for stroke measurements were given out.An effective method was provided,which made the process parameters progressively optimize under the software environment using friendly interface of person-and-computer communication.This method was also adaptable to optimize parameters of other production process which are hard to model.展开更多
Cinderella National Ballet of China.Date:Febuary 2-4,2024.Venue:National Center for the Performing Arts.Rooted in romance and decorum,Cinderella is a tale of courage,hope,and heart that is suitable for audiences of al...Cinderella National Ballet of China.Date:Febuary 2-4,2024.Venue:National Center for the Performing Arts.Rooted in romance and decorum,Cinderella is a tale of courage,hope,and heart that is suitable for audiences of all ages.Founded in December 1959,the National Ballet of China has top-notch artistic personnel trained at professional art institutes and keeps drawing on the strengths of different art genres with Russian skills as its core.In addition to ushering in a high number of world classics,it has independently produced numerous masterpieces with distinct national characteristics,featureing an amazing fusion of the classical with the modern and the national with the international.展开更多
With the progress of computer technology, CAD technique is urgent needed. In this paper, we conduct numerical and theoretical analysis and research on computer aided design technique and novel pattern for electronic a...With the progress of computer technology, CAD technique is urgent needed. In this paper, we conduct numerical and theoretical analysis and research on computer aided design technique and novel pattern for electronic architectural drawing and perspective. AUTOCAD drawing soRware because of its versatility and easy entry, in engineering has broad user base, but also because of the basis of general drawing software, often cannot directly use of the existing order efficiently complete professional drawing. We modify the current pattern and introduce our proposed pattern for advancement. The experiment proves the effectiveness of the pattern. In addition, we will conduct more insightful research in the future to nolish the current anoroach.展开更多
For discrimination of the common W-junction and Y-junction in the labels of line drawing for a three-dimensional manifold plane surface with trihedral vertices, the existing algorithms are almost using angles between ...For discrimination of the common W-junction and Y-junction in the labels of line drawing for a three-dimensional manifold plane surface with trihedral vertices, the existing algorithms are almost using angles between two adjacent lines and W-junction and Y- junction's definitions, and other complex methods. This passage gives four methods with their detailed mathematical inference processes in order to use these algorithms implemented by computer. The algorithms listed are Angle Summation method and Points to the Line method, Triangle methods which are the Triangle Area method and the Cross method. When the computer programs discriminate junctions, by comparison, the Angle Summation method and Points to the Line method are less efficacious than the Triangle method, and Cross method is more efficacious than the Triangle Area method in the Triangle method.展开更多
This report gives a view of a computer multimedia book of mechanical drawing. This electronic book is developed under Windows and Chinese Star to form an integrated system on a CD-ROM. In the electronic book, graphics...This report gives a view of a computer multimedia book of mechanical drawing. This electronic book is developed under Windows and Chinese Star to form an integrated system on a CD-ROM. In the electronic book, graphics, images, 3D animation, audio, video and text techniques of computer multimedia are applied. The techniques, methods, contents and purpose of developing this system are introduced.展开更多
In this paper, the forming features of tapered rectangular box during hydrodynamic deep drawing are studied by means of FEM.The effect rules of square blank corner corner amount on body wrinkling are recognized and co...In this paper, the forming features of tapered rectangular box during hydrodynamic deep drawing are studied by means of FEM.The effect rules of square blank corner corner amount on body wrinkling are recognized and corresponding methods are discussed. At last, the results of FEM are verified by experi- ment.展开更多
During 28-29, September 2005, water was drawn from Hanjiang River and Houguan Lake to the Yangzi River via Sanjiao Lake and Nantaizi Lake in Wuhan in order to provide favorable conditions for ecosystem restoration. To...During 28-29, September 2005, water was drawn from Hanjiang River and Houguan Lake to the Yangzi River via Sanjiao Lake and Nantaizi Lake in Wuhan in order to provide favorable conditions for ecosystem restoration. To evaluate the feasibility and validity of drawing water as a means of ecosystem restoration, zooplankton populations were studied 3 times (before, immediately after finishing and a month after drawing water) at seven locations from 27 Sept. 2005 to 2 Nov. 2005. Water quality in the lakes was mostly improved and zooplankton species richness decreased as soon as drawing water had finished but increased a month after drawing water. Zooplankton density and biomass was reduced in the lakes by drawing water but was increased at the entrance to Sanjiao Lake because of landform geometry change. Before drawing water, most species in Sanjiao Lake e.g., Brachionus sp. and Keratella sp. were tolerant of contamination. After drawing water oligotrophic-prone species such as Lecane ludwigii and Gastropus stylifer emerged. We conclude that drawing water could be important for improving water quality and favour ecosystem restoration. Dilution of nutrient concentrations may be an important role in the effect.展开更多
In sheet metal forming, drawbeads are often used to control uneven material flow which may cause defects such as wrinkles, fracture, surface distortion and springback. Appropriate setting and adjusting the drawbead ...In sheet metal forming, drawbeads are often used to control uneven material flow which may cause defects such as wrinkles, fracture, surface distortion and springback. Appropriate setting and adjusting the drawbead force is one of the most important pa- rameters in sheet metal forming process control. This paper derives the model of loop drawbead restraining force (DBRF) using plastic forming theory, and gives the min imum blankholding force. Experiments are carried out to verify the proposed DBRF model. The good agreement between the calculated values and experiments data justi- fies the proposed loop drawbead restraining force model.展开更多
The deformation characteristic of bland in deep drawing is discussed. It is pointed out that the friction and lubrication conditions in for drawing are different from that in mechanical motion or machine work or other...The deformation characteristic of bland in deep drawing is discussed. It is pointed out that the friction and lubrication conditions in for drawing are different from that in mechanical motion or machine work or other plastic process. The common test methods in laboratories are analyzed. It shows that though all those test methods can test the friction coefficient, the probe test method is most suitable for the research of friction and lubrication and the process in deep drawing, for this method is identical with the actual work condition either from the test principle or deformation status of the blank. Last the successful application in the deep drawing simulator newly developed the the probe method are intro- duced in detail.展开更多
Subsurface macro-inclusions and hooks are detrimental to the surface quality of deep-drawing steel sheets. However, little is known about the relationship between macro-inclusions and hooks. Thus, in this work, two ul...Subsurface macro-inclusions and hooks are detrimental to the surface quality of deep-drawing steel sheets. However, little is known about the relationship between macro-inclusions and hooks. Thus, in this work, two ultralow carbon (ULC) steel slabs and two low carbon (LC) aluminum-killed steel slabs were sampled to study the relationship between hooks and subsurface macro-inclusions, which were detected on the cross-sections of steel samples with an area of 56058 mm2 using an automated scanning electron microscopy/energy-disper-sive X-ray spectroscopy system. Results show that subsurface inclusions larger than 200 μm were almost entrapped by hook structures, whereas the location of other inclusions smaller than 200μm had no obvious dependence on the location of solidified hooks. Furthermore, the number density (ND) of subsurface inclusions larger than 200μm decreased from 0.02 to 0 cm-2 in ULC steel as the mean hook depth decreased from 1.57 to 1.01 mm. Similar trends were also observed in LC steel. In addition, the detected inclusions larger than 200μm were concentrated in the region near the slab center (3/8 width-5/8 width), where hook depths were also larger than those at any other locations. Therefore, minimizing the hook depth is an effective way to reduce inclusion-induced sliver defects in deep-drawing steels.展开更多
The influence of high-density pulsing current on the work-hardening behaviour of H0Cr17Ni6Mn3 and 1Cr18Ni9 stainless steels in wire-drawing deformation processes has been studied. It was found that the drawing stress ...The influence of high-density pulsing current on the work-hardening behaviour of H0Cr17Ni6Mn3 and 1Cr18Ni9 stainless steels in wire-drawing deformation processes has been studied. It was found that the drawing stress and the work-hardening rate of wires were significantly reduced by applying current pulses in drawing process. The work-hardening behavior of the multi-courses drawing deformation can be well described by Hollomon formula σ=κΕn. With the application of current pulses in drawing deformation, the work-hardening exponents of H0Cr17Ni6Mn3 steel wires and 1Cr18Ni9 stainless steel wires were reduced by 33% and 45%, respectively, and their work-hardening coefficients were reduced by 41% and 47%, respectively. It was also found that the work-hardening coefficient of wires was reduced with the increment of the frequency of current pulses, while the work-hardening exponents of both steels were insensitive to the pulsing frequency.展开更多
In order to meet the forming demands for low plasticity materials and large height-diameter ratio parts, a new process of hydrodynamic deep drawing (HDD) with independent radial hydraulic pressure is proposed. To in...In order to meet the forming demands for low plasticity materials and large height-diameter ratio parts, a new process of hydrodynamic deep drawing (HDD) with independent radial hydraulic pressure is proposed. To investigate the effects of loading paths on the HDD with independent radial hydraulic pressure, the forming process of 5A06 aluminum alloy cylindrical cup with a hemispherical bottom was studied by numerical simulation. By employing the dynamic explicit analytical software ETA/Dynaform based on LS-DYNA3D, the effects of loading paths on the sheet-thickness distribution and surface quality were analyzed. The corresponding relations of the radial hydraulic pressure loading paths and the part's strain status on the forming limit diagram (FLD) were also discussed. The results indicated that a sound match between liquid chamber pressure and independent radial hydraulic pressure could restrain the serious thinning at the hemisphere bottom and that through adjusting radial hydraulic pressure could reduce the radial tensile strain and change the strain paths. Therefore, the drawing limit of the aluminum cylindrical cup with a hemispherical bottom could be increased significantly.展开更多
基金financially supported by the National Natural Science Foundation of China (No. 52175284)the State Key Lab of Advanced Metals and Materials in University of Science and Technology Beijing (No. 2021ZD08)
文摘At present,iron and steel enterprises mainly use“after spot test ward”to control final product quality.However,it is impossible to realize on-line quality predetermining for all products by this traditional approach,hence claims and returns often occur,resulting in major eco-nomic losses of enterprises.In order to realize the on-line quality predetermining for steel products during manufacturing process,the predic-tion models of mechanical properties based on deep learning have been proposed in this work.First,the mechanical properties of deep drawing steels were predicted by using LSTM(long short team memory),GRU(gated recurrent unit)network,and GPR(Gaussian process regression)model,and prediction accuracy and learning efficiency for different models were also discussed.Then,on-line re-learning methods for transfer learning models and model parameters were proposed.The experimental results show that not only the prediction accuracy of optimized trans-fer learning models has been improved,but also predetermining time was shortened to meet real time requirements of on-line property prede-termining.The industrial production data of interstitial-free(IF)steel was used to demonstrate that R2 value of GRU model in training stage reaches more than 0.99,and R2 value in testing stage is more than 0.96.
基金This project is supported by National 863/CIMS plan (No.863-511-507) and Natural Science Foundation of Anhui Province (No.01042209)
文摘The implementation methods of computer aided design,drawing and drawing management for plate cuttingmachine are discussed. The system structure for plate cutting- machine design is put forward firstly, then some key technologies and their implementation methods are introduced, which include the structure management of graphics, the unification of graph and design calculation, information share of part, assemble and drawing management system, and movement simulation of key components.
基金Supported by Beijing City Institution of Higher Learning Talent Education Program Project Foundation (PHR200906213PHR201007234)
文摘Based on the necessity of three dimensional modeling with computer in teaching reform, this paper is the summarization of reform practice of teaching engineering drawing in our institute. The teaching reform begins with three dimensional modeling that used computer instead of board. On the basis of target of teaching reform, set of teaching content, arrangement of class hour and teaching method, the research of teaching practice have been done, and very good effects in teaching of engineering drawing have been achieved.
文摘Hubei Tianmen Textile Machinery Co.,Ltd.is a well-known enterprise and key high-tech enterprise in China textile industry.The company's leading product,drawing frame,has completely independent intellectual property rights,among which TM 11 is well received by users and has a high market share in China.
文摘The inherent teaching approach can no longer meet the demands of society.In this paper,current issues within the teaching landscape of architectural engineering technology in higher vocational colleges as well as the policies and teaching demands that formed the basis of this model were analyzed.The study shows the importance of the implementation of the teaching model“promoting teaching and learning through competitions.”This model puts emphasis on the curriculum and teaching resources,while also integrating the teaching process and evaluation with competition.These efforts aim to drive education reform in order to better align with the objectives of vocational education personnel training,while also acting as a reference for similar courses.
文摘In high speed wire drawing, the temperature rise is produced by the generation heat from plastic deformation of metal material and friction between wire and tool, which greatly influences the lubrication situation and mechanical properties. During high drawing, the phenomenon that wire is embrittled and die is stuck can be formed by the notable temperature rise. In this paper, based on theory of plastic deformation work , considering friction heat generation and variable physical coefficients, the mathematical model of temperature rise of high speed drawing is established and the computer program to analogy the whole process of drawing is compiled. Also the process of wire drawing on a few of alloys are calculated theoretically. Compared the calculation value with measurement, the result shows that the theoretical value coincides with experimental data.
文摘A computer control system for drawing machine in horizontal continuous cast set was introduced.The operation features of the drawing machine were analyzed»the hardware configuration and principles of interface circuit for stroke measurements were given out.An effective method was provided,which made the process parameters progressively optimize under the software environment using friendly interface of person-and-computer communication.This method was also adaptable to optimize parameters of other production process which are hard to model.
文摘Cinderella National Ballet of China.Date:Febuary 2-4,2024.Venue:National Center for the Performing Arts.Rooted in romance and decorum,Cinderella is a tale of courage,hope,and heart that is suitable for audiences of all ages.Founded in December 1959,the National Ballet of China has top-notch artistic personnel trained at professional art institutes and keeps drawing on the strengths of different art genres with Russian skills as its core.In addition to ushering in a high number of world classics,it has independently produced numerous masterpieces with distinct national characteristics,featureing an amazing fusion of the classical with the modern and the national with the international.
文摘With the progress of computer technology, CAD technique is urgent needed. In this paper, we conduct numerical and theoretical analysis and research on computer aided design technique and novel pattern for electronic architectural drawing and perspective. AUTOCAD drawing soRware because of its versatility and easy entry, in engineering has broad user base, but also because of the basis of general drawing software, often cannot directly use of the existing order efficiently complete professional drawing. We modify the current pattern and introduce our proposed pattern for advancement. The experiment proves the effectiveness of the pattern. In addition, we will conduct more insightful research in the future to nolish the current anoroach.
文摘For discrimination of the common W-junction and Y-junction in the labels of line drawing for a three-dimensional manifold plane surface with trihedral vertices, the existing algorithms are almost using angles between two adjacent lines and W-junction and Y- junction's definitions, and other complex methods. This passage gives four methods with their detailed mathematical inference processes in order to use these algorithms implemented by computer. The algorithms listed are Angle Summation method and Points to the Line method, Triangle methods which are the Triangle Area method and the Cross method. When the computer programs discriminate junctions, by comparison, the Angle Summation method and Points to the Line method are less efficacious than the Triangle method, and Cross method is more efficacious than the Triangle Area method in the Triangle method.
文摘This report gives a view of a computer multimedia book of mechanical drawing. This electronic book is developed under Windows and Chinese Star to form an integrated system on a CD-ROM. In the electronic book, graphics, images, 3D animation, audio, video and text techniques of computer multimedia are applied. The techniques, methods, contents and purpose of developing this system are introduced.
文摘In this paper, the forming features of tapered rectangular box during hydrodynamic deep drawing are studied by means of FEM.The effect rules of square blank corner corner amount on body wrinkling are recognized and corresponding methods are discussed. At last, the results of FEM are verified by experi- ment.
文摘During 28-29, September 2005, water was drawn from Hanjiang River and Houguan Lake to the Yangzi River via Sanjiao Lake and Nantaizi Lake in Wuhan in order to provide favorable conditions for ecosystem restoration. To evaluate the feasibility and validity of drawing water as a means of ecosystem restoration, zooplankton populations were studied 3 times (before, immediately after finishing and a month after drawing water) at seven locations from 27 Sept. 2005 to 2 Nov. 2005. Water quality in the lakes was mostly improved and zooplankton species richness decreased as soon as drawing water had finished but increased a month after drawing water. Zooplankton density and biomass was reduced in the lakes by drawing water but was increased at the entrance to Sanjiao Lake because of landform geometry change. Before drawing water, most species in Sanjiao Lake e.g., Brachionus sp. and Keratella sp. were tolerant of contamination. After drawing water oligotrophic-prone species such as Lecane ludwigii and Gastropus stylifer emerged. We conclude that drawing water could be important for improving water quality and favour ecosystem restoration. Dilution of nutrient concentrations may be an important role in the effect.
文摘In sheet metal forming, drawbeads are often used to control uneven material flow which may cause defects such as wrinkles, fracture, surface distortion and springback. Appropriate setting and adjusting the drawbead force is one of the most important pa- rameters in sheet metal forming process control. This paper derives the model of loop drawbead restraining force (DBRF) using plastic forming theory, and gives the min imum blankholding force. Experiments are carried out to verify the proposed DBRF model. The good agreement between the calculated values and experiments data justi- fies the proposed loop drawbead restraining force model.
文摘The deformation characteristic of bland in deep drawing is discussed. It is pointed out that the friction and lubrication conditions in for drawing are different from that in mechanical motion or machine work or other plastic process. The common test methods in laboratories are analyzed. It shows that though all those test methods can test the friction coefficient, the probe test method is most suitable for the research of friction and lubrication and the process in deep drawing, for this method is identical with the actual work condition either from the test principle or deformation status of the blank. Last the successful application in the deep drawing simulator newly developed the the probe method are intro- duced in detail.
文摘Subsurface macro-inclusions and hooks are detrimental to the surface quality of deep-drawing steel sheets. However, little is known about the relationship between macro-inclusions and hooks. Thus, in this work, two ultralow carbon (ULC) steel slabs and two low carbon (LC) aluminum-killed steel slabs were sampled to study the relationship between hooks and subsurface macro-inclusions, which were detected on the cross-sections of steel samples with an area of 56058 mm2 using an automated scanning electron microscopy/energy-disper-sive X-ray spectroscopy system. Results show that subsurface inclusions larger than 200 μm were almost entrapped by hook structures, whereas the location of other inclusions smaller than 200μm had no obvious dependence on the location of solidified hooks. Furthermore, the number density (ND) of subsurface inclusions larger than 200μm decreased from 0.02 to 0 cm-2 in ULC steel as the mean hook depth decreased from 1.57 to 1.01 mm. Similar trends were also observed in LC steel. In addition, the detected inclusions larger than 200μm were concentrated in the region near the slab center (3/8 width-5/8 width), where hook depths were also larger than those at any other locations. Therefore, minimizing the hook depth is an effective way to reduce inclusion-induced sliver defects in deep-drawing steels.
基金supported by the laboratory foundation of Tsinghua Universitythe'985'research foundation of Tsinghua University
文摘The influence of high-density pulsing current on the work-hardening behaviour of H0Cr17Ni6Mn3 and 1Cr18Ni9 stainless steels in wire-drawing deformation processes has been studied. It was found that the drawing stress and the work-hardening rate of wires were significantly reduced by applying current pulses in drawing process. The work-hardening behavior of the multi-courses drawing deformation can be well described by Hollomon formula σ=κΕn. With the application of current pulses in drawing deformation, the work-hardening exponents of H0Cr17Ni6Mn3 steel wires and 1Cr18Ni9 stainless steel wires were reduced by 33% and 45%, respectively, and their work-hardening coefficients were reduced by 41% and 47%, respectively. It was also found that the work-hardening coefficient of wires was reduced with the increment of the frequency of current pulses, while the work-hardening exponents of both steels were insensitive to the pulsing frequency.
文摘In order to meet the forming demands for low plasticity materials and large height-diameter ratio parts, a new process of hydrodynamic deep drawing (HDD) with independent radial hydraulic pressure is proposed. To investigate the effects of loading paths on the HDD with independent radial hydraulic pressure, the forming process of 5A06 aluminum alloy cylindrical cup with a hemispherical bottom was studied by numerical simulation. By employing the dynamic explicit analytical software ETA/Dynaform based on LS-DYNA3D, the effects of loading paths on the sheet-thickness distribution and surface quality were analyzed. The corresponding relations of the radial hydraulic pressure loading paths and the part's strain status on the forming limit diagram (FLD) were also discussed. The results indicated that a sound match between liquid chamber pressure and independent radial hydraulic pressure could restrain the serious thinning at the hemisphere bottom and that through adjusting radial hydraulic pressure could reduce the radial tensile strain and change the strain paths. Therefore, the drawing limit of the aluminum cylindrical cup with a hemispherical bottom could be increased significantly.