Three-dimensional physical simulation and optimization of water injection of a multi-well fractured-vuggy unit

With complex fractured-vuggy heterogeneous structures, water has to be injected to facilitate oil pro- duction. However, the effect of different water injection modes on oil recovery varies. The limitation of existing numerical simulation methods in representing fractured- vuggy carbonate reservoirs makes numerical simulation difficult to characterize the fluid flow in these reservoirs. In this paper, based on a geological example unit in the Tahe Oilfield, a three-dimensional physical model was designed and constructed to simulate fluid flow in a fractured-vuggy reservoir according to similarity criteria. The model was validated by simulating a bottom water drive reservoir, and then subsequent water injection modes were optimized. These were continuous （constant rate）, intermittent, and pulsed injection of water. Experimental results reveal that due to the unbalanced formation pressure caused by pulsed water injection, the swept volume was expanded and consequently the highest oil recovery increment was achieved. Similar to continuous water injection, intermit- tent injection was influenced by factors including the connectivity of the fractured-vuggy reservoir, well depth, and the injection-production relationship, which led to a relative low oil recovery. This study may provide a constructive guide to field production and for the devel- opment of the commercial numerical models specialized for fractured-vuggy carbonate reservoirs.

Intelligent Metal Detection and Disposal Automation Equipment Based on Geometric Optimization Driving Algorithm

In order to solve the problem of metal impurities mixed in the production line of wood pulp nonwoven raw materials,intelligent metal detection and disposal automation equipment is designed.Based on the principle of electromagnetic induction,the precise positioning of metal coordinates is realized by initial inspection and multi-directional re-inspection.Based on a geometry optimization driving algorithm,the cutting area is determined by locating the center of the circle that covers the maximum area.This approach aims to minimize the cutting area and maximize the use of materials.Additionally,the method strives to preserve as many fabrics at the edges as possible by employing the farthest edge covering circle algorithm.Based on a speed compensation algorithm,the flexible switching of upper and lower rolls is realized to ensure the maximum production efficiency.Compared with the metal detection device in the existing production line,the designed automation equipment has the advantages of higher detection sensitivity,more accurate metal coordinate positioning,smaller cutting material areas and higher production efficiency,which can make the production process more continuous,automated and intelligent.

A novel two-degree-of-freedom spherical ultrasonic motor using three travelling-wave type annular stators

In order to promote the tolerance and controllability of the multi-degree-of-freedom(M-DOF) ultrasonic motor, a novel two-degree-of-freedom(2-DOF) spherical ultrasonic motor using three traveling-wave type annular stators was put forward. Firstly,the structure and working principle of this motor were introduced, especially a spiral spring as the preload applied component was designed for adaptive adjustment. Then, the friction drive model of 2-DOF spherical motor was built up from spatial geometric relation between three annular stators and the spherical rotor which was used to analyze the mechanical characteristics of the motor.The optimal control strategy for minimum norm solution of three stators' angular velocity was proposed, using Moore-Penrose generalized inverse matrix. Finally, a 2-DOF prototype was fabricated and tested, which ran stably and controllably. The maximum no-load velocity and stall torque are 92 r/min and 90 m N·m, respectively. The 2-DOF spherical ultrasonic motor has compact structure, easy assembly, good performance and stable operation.

OPTIMAL TORQUE CONTROL STRATEGY FOR PARALLEL HYBRID ELECTRIC VEHICLE WITH AUTOMATIC MECHANICAL TRANSMISSION

In parallel hybrid electrical vehicle （PHEV） equipped with automatic mechanical transmission （AMT）, the driving smoothness and the clutch abrasion are the primary considerations for powertrain control during gearshift and clutch operation. To improve these performance indexes of PHEV, a coordinated control system is proposed through the analyzing of HEV powertrain dynamic characteristics. Using the method of minimum principle, the input torque of transmission is optimized to improve the driving smoothness of vehicle. Using the methods of fuzzy logic and fuzzy-PID, the engaging speed of clutch and the throttle opening of engine are manipulated to ensure the smoothness of clutch engagement and reduce the abrasion of clutch friction plates. The motor provides the difference between the required input torque of transmission and the torque transmitted through clutch plates. Results of simulation and experiments show that the proposed control strategy performs better than the contrastive control system, the smoothness of driving and the abrasion of clutch can be improved simultaneously.

A fault-tolerant triple-redundant voice coil motor for direct drive valves:Design, optimization, and experiment

A direct drive actuator （DDA） with direct drive valves （DDVs） as the control device is an ideal solution for a flight actuation system. This paper presents a novel triple-redundant voice coil motor （TRVCM） used for redundant DDVs. The TRVCM features electrical/mechanical hybrid triple-redundancy by securing three stators along with three moving coils in the same frame. A permanent magnet （PM） Halbach array is employed in each redundant VCM to simplify the system structure. A back-to-back design between neighborly redundancies is adopted to decouple the magnetic flux linkage. The particle swarm optimization （PSO） method is implemented to optimize design parameters based on the analytical magnetic circuit model. The optimization objective function is defined as the acceleration capacity of the motor to achieve high dynamic performance. The optimal geometric parameters are verified with 3D magnetic field finite element analysis （FEA）. A research prototype has been developed for experimental purpose. The experimental results of magnetic field density and force output show that the proposed TRVCM has great potential of applications in DDA systems.

Assessing clogging potential and optimizing driving parameter of slurry shield tunneling in clay stratum assisted with CFD-DEM modeling

This paper proposed a two-way coupled computational fluid dynamics(CFD)and discrete element method(DEM)approach to analyze the evolution of clogging in slurry shield tunneling quantitatively.The interactions between clay particles and slurry were considered by exchanging three interaction forces,including buoyancy force,pressure gradient force,and drag force.The CFD-DEM coupling approach was first benchmarked by comparing cutterhead torque and total thrust with field monitored data of a practical slurry shield tunnel project.The evolution process of the particle phase and the fluid phase over time was presented.The results indicated that fewer than 70%of the particles can be washed away in time by the circulating slurry.About 9%of the particles adhered to the submerged wall,resulting in increased cutterhead torque and thrust.Through parametric analysis,the influence of the shield driving parameters on the clay clogging behavior is further explored.The time history of cutterhead torque or thrust can be used as a criterion for judging whether clogging has occurred.Additionally,a new assessment method of clogging risk and an optimization strategy of driving parameters were proposed,which were intended to provide some guidance for similar projects.

A minimal-energy driving strategy for high-speed electric train

This paper investigates the minimal-energy driving problem for high-speed electric train, and then proposes a three-stage optimal strategy. First, a switching system model is introduced to describe the new dynamics in high-speed electric train, which considers the extended range of speed, the energy efficiency and the regenerative brake. Based on the new model, the optimal driving strategy with minimal-energy consumption is studied, and the problem is boiled down to optimal control for switching systems. Using a numerical algorithm, a three-stage driving strategy is concluded, in which the traditional quasi-coasting stage is discarded and the maximal traction and brake are not suitable anymore. Finally, a case study on CRH is illustrated.