Droplet size distributions have been investigated with a two-probe system above a rotatingstream tray of 300 mm diameter.The measured distributions are found to follow the upper limitedlognormal distribution with thre...Droplet size distributions have been investigated with a two-probe system above a rotatingstream tray of 300 mm diameter.The measured distributions are found to follow the upper limitedlognormal distribution with three parameters dependent primarily on gas hole F-factor.A probabilitymethod is used to describe the initial state of the droplet population above the tray,and a model fordroplet motion is presented.The results computed with model agree well with experimental data.展开更多
A droplet undergoes spreading,rebounding or splashing when it impacts solid boundary,which is a typical phenomenon of free surface flow that exists widely in modern industry.Smoothed particle hydrodynamics(SPH)method ...A droplet undergoes spreading,rebounding or splashing when it impacts solid boundary,which is a typical phenomenon of free surface flow that exists widely in modern industry.Smoothed particle hydrodynamics(SPH)method is applied to numerically study the dynamical behaviors of the droplet impacting solid boundary,and both the spreading and rebounding phenomena of the droplet are reproduced in the simulation.The droplet deformation,flow fields and pressure fields inside the droplet at different moments are analyzed.Two important factors,the initial velocity and diameter,are discussed in determining the maximum spreading factor,revealing that the maximum spreading factor increases with the increase of the impact velocity and droplet diameter respectively.展开更多
A new droplet collision and coalescence model was presented, a quick-sort method for locating collision partners was also devised and based on theoretical and experimental results, further advancement was made to the ...A new droplet collision and coalescence model was presented, a quick-sort method for locating collision partners was also devised and based on theoretical and experimental results, further advancement was made to the droplet collision outcome. The advantages of the two implementations of smoothed particle hydrodynamics （SPH） method were used to limit the collision of droplets to a given number of nearest droplets and define the probability of coalescence, numerical simulations were carried out for model validation. Results show that the model presented is mesh-independent and less time consuming, it can not only maintains the system momentum conservation perfectly, but not susceptible to initial droplet size distribution as well.展开更多
Directional solidification methods are being used f or in-situ production of metallic immiscible composites. A quantitative understa nding of the dynamic behavior and growth kinetics of the nucleated second phase duri...Directional solidification methods are being used f or in-situ production of metallic immiscible composites. A quantitative understa nding of the dynamic behavior and growth kinetics of the nucleated second phase during solidification is necessary to produce homogeneous dispersion in solidifi ed composites. This paper presents a mathematical model for describing the grow th of nucleated dispersed phase in the two-liquid phase region ahead of the sol idification front and the entrapment of these droplets by the moving solid-liqu id interface in vertical unidirectional solidification systems. The model has t wo components. A macro-heat transfer model for describing the temperature prof iles and the rate of advance of the solidification front. The dynamic behavior and coalescence and growth of nucleated droplets in the two-liquid phase region under the influence of effective gravity and thermocapillary forces were repres ented through the solution the droplet momentum and mass conservation equations in particle space. These two components of the models were coupled through a sp ecial algorithm for tracking the particle location and size with respect to movi ng solidification front in the solidification time scale. The model is used to study the particle size distribution in unidirectional solidified Zn-Bi hypermo notectic alloys at reduced gravity conditions. It has been found that the parti cle size and distribution in the solidified alloy depends on solidification rate and the ratio of effective gravity to thermocapillary forces. It was also foun d that uniform dispersion could only be obtained in a very narrow range of effec tive gravity values near zero gravity. The model predictions were compared agai nst experimental measurements obtained at different effective gravity conditions in a novel unidirectional solidification apparatus that uses electromagnetic fo rces to modulate gravitational forces. The model was found to reasonably predic t the experimentally measured particle size and distribution over the entire ran ge of effective gravity investigated as well as gravity conditions for settling and flotation of the second phase during solidification. The practical signific ance of these findings will be discussed.展开更多
The distribution of droplet surface pressure is uneven?under the action of high velocity gas streams in gas wells, and there exists a pressure difference which leads to droplet deformation before and after the droplet...The distribution of droplet surface pressure is uneven?under the action of high velocity gas streams in gas wells, and there exists a pressure difference which leads to droplet deformation before and after the droplet. Moreover, it affects the critical liquid carrying rate. The pressure difference prediction model must be determined, because of the existing one lacking theoretical basis. Based on the droplet surface pressure distribution in high velocity gas streams, a new model is established to predict the average differential pressure of droplets. Compared with the new differential pressure prediction results, the existing pressure difference prediction results were overvalued by 46.0%. This article also improves four gas-well critical liquid carrying models using the proposed pressure difference prediction model, and compares with the original one. The result indicates that the critical velocity of the original models is undervalued by 10% or so, due to the overestimate to the pressuredifference. In addition, comparisons of the improved model with original models show that it is necessary to consider the adaptability, because the models have significant differences in results, and different suitability for different well conditions.展开更多
Based on the lattice Boltzmann method（LBM）,an improved pseudo-potential model,combined with a method of adding force term,is used to simulate the two-phase flows caused by a liquid droplet impacting on a liquid film...Based on the lattice Boltzmann method（LBM）,an improved pseudo-potential model,combined with a method of adding force term,is used to simulate the two-phase flows caused by a liquid droplet impacting on a liquid film.In this model,the different phases are treated as one fluid,and the interfaces between the vapor and liquid phases can be obtained by density value of the fluid.This variant of the LBM allows one to obtain the densities of vapor and liquid with high accuracy.The model is validated by an example of phase separation.The early stage of the impact of droplet on liquid film is simulated,and the results are qualitatively consistent with physical phenomena.展开更多
In this paper,the lattice-Boltzmann method is used to investigate the droplet dynamics after impact on horizontal and inclined solid surface. The two-phase interparticle potential model is employed. The model is found...In this paper,the lattice-Boltzmann method is used to investigate the droplet dynamics after impact on horizontal and inclined solid surface. The two-phase interparticle potential model is employed. The model is found to possess a linear relation between the macroscopic properties( surface tension σ and contact angle α)and microscopic parameters( G,G t). The flow state of the droplet on the surface is analyzed in detail,and the effects of surface characteristic,impact velocity,impact angle,the viscosity and surface tension of the liquid are investigated,respectively. It is shown that the lattice-Boltzmann method can not only track exactly and automatically the interface,but also the simulation results have a good qualitative agreement with ones of the previous experimental and numerical studies.展开更多
Aerosol indirect effects on warm clouds are estimated in the Grid-point Atmospheric Model of the State Key Laboratory of Numerical Modeling for Atmospheric Sciences and Geophysical Fluid Dynamics,Institute of Atmosphe...Aerosol indirect effects on warm clouds are estimated in the Grid-point Atmospheric Model of the State Key Laboratory of Numerical Modeling for Atmospheric Sciences and Geophysical Fluid Dynamics,Institute of Atmospheric Physics(IAP LASG)(GAMIL) with a new two-moment cloud microphysics scheme using two different physically-based aerosol activation parameterizations:Abdul-Razzak and Ghan,and Nenes and Seinfeld.The annual global mean changes in shortwave cloud forcing from preindustrial times to present day(a measure of the aerosol indirect effects) estimated from these two parameterizations are remarkably similar:0.76 W m?2 with the Abdul-Razzak and Ghan parameterization,and 0.78 W m?2 with the Nenes and Seinfeld parameterization.Physically-based parameterizations can provide robust representations of aerosol effects on droplet nucleation,meaning that aerosol activation is no longer the most uncertain factor in modeling aerosol indirect effects.展开更多
The heat input from arcs to weld pool in twin-arc gas metal arc welding （GMAW） with a common weld pool is investigated by high-speed photography. The characteristics of arc shapes and droplet transfer are studied an...The heat input from arcs to weld pool in twin-arc gas metal arc welding （GMAW） with a common weld pool is investigated by high-speed photography. The characteristics of arc shapes and droplet transfer are studied and then the models for heat flux distribution on top surface of weld pool and enthalpy distribution of metal droplets transferred into weld pool are established. By using the model, 3-D geometries of weld pools in twin-arc GMAW with a common weld pool are predicted. Corresponding welding experiments on mild steel plates are carried out and the results indicate that the predicted shape of weld bead on cross section shows good agreement with measured one.展开更多
基金Supported by the National and Zhejiang Provincial Natural Science Foundations.
文摘Droplet size distributions have been investigated with a two-probe system above a rotatingstream tray of 300 mm diameter.The measured distributions are found to follow the upper limitedlognormal distribution with three parameters dependent primarily on gas hole F-factor.A probabilitymethod is used to describe the initial state of the droplet population above the tray,and a model fordroplet motion is presented.The results computed with model agree well with experimental data.
基金Supported by the National Natural Science Foundation of China(No.51079095)the Science Fund for Creative Research Groups of the National Natural Science Foundation of China(No.51021004)
文摘A droplet undergoes spreading,rebounding or splashing when it impacts solid boundary,which is a typical phenomenon of free surface flow that exists widely in modern industry.Smoothed particle hydrodynamics(SPH)method is applied to numerically study the dynamical behaviors of the droplet impacting solid boundary,and both the spreading and rebounding phenomena of the droplet are reproduced in the simulation.The droplet deformation,flow fields and pressure fields inside the droplet at different moments are analyzed.Two important factors,the initial velocity and diameter,are discussed in determining the maximum spreading factor,revealing that the maximum spreading factor increases with the increase of the impact velocity and droplet diameter respectively.
基金Project supported by the National Natural Science Foundation of China(No.50376054)and the Aerospace Science Foundation(No.03c53021)
文摘A new droplet collision and coalescence model was presented, a quick-sort method for locating collision partners was also devised and based on theoretical and experimental results, further advancement was made to the droplet collision outcome. The advantages of the two implementations of smoothed particle hydrodynamics （SPH） method were used to limit the collision of droplets to a given number of nearest droplets and define the probability of coalescence, numerical simulations were carried out for model validation. Results show that the model presented is mesh-independent and less time consuming, it can not only maintains the system momentum conservation perfectly, but not susceptible to initial droplet size distribution as well.
文摘Directional solidification methods are being used f or in-situ production of metallic immiscible composites. A quantitative understa nding of the dynamic behavior and growth kinetics of the nucleated second phase during solidification is necessary to produce homogeneous dispersion in solidifi ed composites. This paper presents a mathematical model for describing the grow th of nucleated dispersed phase in the two-liquid phase region ahead of the sol idification front and the entrapment of these droplets by the moving solid-liqu id interface in vertical unidirectional solidification systems. The model has t wo components. A macro-heat transfer model for describing the temperature prof iles and the rate of advance of the solidification front. The dynamic behavior and coalescence and growth of nucleated droplets in the two-liquid phase region under the influence of effective gravity and thermocapillary forces were repres ented through the solution the droplet momentum and mass conservation equations in particle space. These two components of the models were coupled through a sp ecial algorithm for tracking the particle location and size with respect to movi ng solidification front in the solidification time scale. The model is used to study the particle size distribution in unidirectional solidified Zn-Bi hypermo notectic alloys at reduced gravity conditions. It has been found that the parti cle size and distribution in the solidified alloy depends on solidification rate and the ratio of effective gravity to thermocapillary forces. It was also foun d that uniform dispersion could only be obtained in a very narrow range of effec tive gravity values near zero gravity. The model predictions were compared agai nst experimental measurements obtained at different effective gravity conditions in a novel unidirectional solidification apparatus that uses electromagnetic fo rces to modulate gravitational forces. The model was found to reasonably predic t the experimentally measured particle size and distribution over the entire ran ge of effective gravity investigated as well as gravity conditions for settling and flotation of the second phase during solidification. The practical signific ance of these findings will be discussed.
文摘The distribution of droplet surface pressure is uneven?under the action of high velocity gas streams in gas wells, and there exists a pressure difference which leads to droplet deformation before and after the droplet. Moreover, it affects the critical liquid carrying rate. The pressure difference prediction model must be determined, because of the existing one lacking theoretical basis. Based on the droplet surface pressure distribution in high velocity gas streams, a new model is established to predict the average differential pressure of droplets. Compared with the new differential pressure prediction results, the existing pressure difference prediction results were overvalued by 46.0%. This article also improves four gas-well critical liquid carrying models using the proposed pressure difference prediction model, and compares with the original one. The result indicates that the critical velocity of the original models is undervalued by 10% or so, due to the overestimate to the pressuredifference. In addition, comparisons of the improved model with original models show that it is necessary to consider the adaptability, because the models have significant differences in results, and different suitability for different well conditions.
基金Project supported by the National Natrual Science Foundation of China (Grant No.10872123)
文摘Based on the lattice Boltzmann method（LBM）,an improved pseudo-potential model,combined with a method of adding force term,is used to simulate the two-phase flows caused by a liquid droplet impacting on a liquid film.In this model,the different phases are treated as one fluid,and the interfaces between the vapor and liquid phases can be obtained by density value of the fluid.This variant of the LBM allows one to obtain the densities of vapor and liquid with high accuracy.The model is validated by an example of phase separation.The early stage of the impact of droplet on liquid film is simulated,and the results are qualitatively consistent with physical phenomena.
基金Sponsored by the National Nature Science Foundation of China(Grant No.51276030,51176017)
文摘In this paper,the lattice-Boltzmann method is used to investigate the droplet dynamics after impact on horizontal and inclined solid surface. The two-phase interparticle potential model is employed. The model is found to possess a linear relation between the macroscopic properties( surface tension σ and contact angle α)and microscopic parameters( G,G t). The flow state of the droplet on the surface is analyzed in detail,and the effects of surface characteristic,impact velocity,impact angle,the viscosity and surface tension of the liquid are investigated,respectively. It is shown that the lattice-Boltzmann method can not only track exactly and automatically the interface,but also the simulation results have a good qualitative agreement with ones of the previous experimental and numerical studies.
基金supported by the National High Technology Research and Development Program of China (Grant No. 2010AA012304)the Knowledge Innovation Program of the Chinese Academy of Sciences (Grant No. KZCX2-YW-Q11-04)the China Meteorological Administration for the R&D Special Fund for Public Welfare Industry (meteorology) (Grant Nos. GYHY200806006 and GYHY200906020)
文摘Aerosol indirect effects on warm clouds are estimated in the Grid-point Atmospheric Model of the State Key Laboratory of Numerical Modeling for Atmospheric Sciences and Geophysical Fluid Dynamics,Institute of Atmospheric Physics(IAP LASG)(GAMIL) with a new two-moment cloud microphysics scheme using two different physically-based aerosol activation parameterizations:Abdul-Razzak and Ghan,and Nenes and Seinfeld.The annual global mean changes in shortwave cloud forcing from preindustrial times to present day(a measure of the aerosol indirect effects) estimated from these two parameterizations are remarkably similar:0.76 W m?2 with the Abdul-Razzak and Ghan parameterization,and 0.78 W m?2 with the Nenes and Seinfeld parameterization.Physically-based parameterizations can provide robust representations of aerosol effects on droplet nucleation,meaning that aerosol activation is no longer the most uncertain factor in modeling aerosol indirect effects.
基金Supported by National Natural Science Foundation of China （ No. 50575074） and the Scientific Research Foundation of QUST.
文摘The heat input from arcs to weld pool in twin-arc gas metal arc welding （GMAW） with a common weld pool is investigated by high-speed photography. The characteristics of arc shapes and droplet transfer are studied and then the models for heat flux distribution on top surface of weld pool and enthalpy distribution of metal droplets transferred into weld pool are established. By using the model, 3-D geometries of weld pools in twin-arc GMAW with a common weld pool are predicted. Corresponding welding experiments on mild steel plates are carried out and the results indicate that the predicted shape of weld bead on cross section shows good agreement with measured one.
