Determination of Natural Logarithm of Diffusion Coefficient and Activation Energy of Thin Layer Drying Process of Ginger Rhizome Slices

This study is an extension of the previous work done with ARS-680 Environmental Chamber. Drying is a complex operation that demands much energy and time. Drying is essentially important for preservation of ginger rhizome. Drying of ginger was modeled, and then the effective diffusion coefficient and activation energy were determined. For this purpose, the experiments were done at six levels of varied temperatures: 10°C, 20°C, 30°C, 40°C, 50°C and 60°C. The values of effective diffusion coefficients obtained in this work for the variously treated ginger rhizomes closely agreed with the average effective diffusion coefficients of other notable authors who determined the drying kinetics and convective heat transfer coefficients of ginger slices.

Effect of different drying methods on the amino acids,α-dicarbonyls and volatile compounds of rape bee pollen

The significant demand for high quality food has motivated us to adopt appropriate processing methods to improve the food nutritional quality and flavors.In this study,the effects of five drying methods,namely,pulsed vacuum drying(PVD),freeze drying(FD),infrared drying(IRD),hot-air drying(HAD)and sun drying(SD)on free amino acids(FAAs),α-dicarbonyl compounds(α-DCs)and volatile compounds(VOCs)in rape bee pollen(RBP)were determined.The results showed that FD significantly released the essential amino acids(EAAs)compared with fresh samples while SD caused the highest loss.Glucosone was the dominantα-DCs in RBP and the highest loss was observed after PVD.Aldehydes were the dominant volatiles of RBP and SD samples contained more new volatile substances(especially aldehydes)than the other four drying methods.Comprehensively,FD and PVD would be potential methods to effectively reduce the quality deterioration of RBP in the drying process.

Effect of drying cracks on swelling and self-healing of bentonite-sand blocks used as engineered barriers for radioactive waste disposal

Experiments were conducted to evaluate the healing of drying cracks in air-dried bentonite-sand blocks after hydration and swelling in groundwater,providing justifications to simplify the protection of blocks prior to installation in a high-level radioactive waste repository.Synthetic groundwater was prepared to represent the geochemistry of Beishan groundwater,and was used to hydrate the blocks during the swelling pressure and swelling strain measurements,as Beishan is the most promising site for China's repository.Healing of the surface cracks was recorded by photography,and healing of the internal cracks was visualized by CT images and hydraulic conductivity of air-dried blocks.The results indicate that the maximum swelling pressure and swelling strain are primarily affected by the geochemistry of Beishan groundwater,but not affected by the drying cracks.The maximum swelling pressure and swelling strain of air-dried blocks are comparable to or even higher than the pressure and strain of fresh blocks.The maximum swelling pressure measured in strong(i.e.high ion strength)Beishan groundwater was 44%of the pressure measured in deionized(DI)water,and the maximum swelling strain was reduced to 23%of the strain measured in DI water.Nevertheless,the remained swelling of the blocks hydrated in strong Beishan groundwater was sufficient to heal the surface and internal drying cracks,as demonstrated by the pictures of surface cracks and CT images.The hydraulic conductivity of the air-dried block permeated with strong groundwater was comparable(3.7×higher)to the hydraulic conductivity of the fresh block,indicating the self-healing of drying cracks after hydration and swelling in groundwater.A simplified method of protecting the block with plastic wraps before installation is recommended,since the remained swelling of the block hydrated in Beishan groundwater is sufficient to heal the drying cracks.

Wetting alternating with partial drying during grain filling increases lysine biosynthesis in inferior rice grain

Lysine content is a criterion of the nutritional quality of rice.Understanding the process of lysine biosynthesis in early-flowering superior grain(SG)and late-flowering inferior grain(IG)of rice would advance breeding and cultivation to improve nutritional quality.However,little information is available on differences in lysine anabolism between SG and IG and the underlying mechanism,and whether and how irrigation regimes affect lysine anabolism in these grains.A japonica rice cultivar was grown in the field and two irrigation regimes,continuous flooding(CF)and wetting alternating with partial drying(WAPD),were imposed from heading to the mature stage.Lysine content and activities of key enzymes of lysine biosynthesis,and levels of brassinosteroids(BRs)were lower in the IG than in the SG at the early grainfilling stage but higher at middle and late grain-filling stages.WAPD increased activities of these key enzymes,BR levels,and contents of lysine and total amino acids in IG,but not SG relative to CF.Application of 2,4-epibrassinolide to rice panicles in CF during early grain filling reproduced the effects of WAPD,but neither treatment altered the activities of enzymes responsible for lysine catabolism in either SG or IG.WAPD and elevated BR levels during grain filling increased lysine biosynthesis in IG.Improvement in lysine biosynthesis in rice should focus on IG.

Solvent transport dynamics and its effect on evolution of mechanical properties of nitrocellulose(NC)-based propellants under hot-air drying process

Appropriate drying process with optimized controlling of drying parameters plays a vital role in the improvement of the quality and performance of propellant products.However,few research on solvent transport dynamics within NC-based propellants was reported,and its effect on the evolution of mechanical properties was not interpreted yet.This study is conducted to gain a comprehensive understanding of hot-air drying for NC-based propellants and clarify the effect of temperature on solvent transport behavior and further the change of mechanical properties during drying.The drying kinetic curves show the drying time required is decreased but the steady solvent content is increased and the drying rate is obviously increased with the increase of hot-air temperatures,indicating hot-air temperatures have a significant effect on drying kinetics.A modified drying model was established,and results show it is more appropriate to describe solvent transport behavior within NC-based propellants.Moreover,two linear equations were established to exhibit the relationship between solvent content and its effect on the change of tensile properties,and the decrease of residual solvent content causes an obvious increase of tensile strength and tensile modulus of propellant products,indicating its mechanical properties can be partly improved by adjustment of residual solvent content.The outcomes can be used to clarify solvent transport mechanisms and optimize drying process parameters of double-based gun propellants.

Asymmetric Drying and Wetting Trends in Eastern and Western China

As an important factor that directly affects agricultural production, the social economy, and policy implementation,observed changes in dry/wet conditions have become a matter of widespread concern. However, previous research has mainly focused on the long-term linear changes of dry/wet conditions, while the detection and evolution of the non-linear trends related to dry/wet changes have received less attention. The non-linear trends of the annual aridity index, obtained by the Ensemble Empirical Mode Decomposition(EEMD) method, reveal that changes in dry/wet conditions in China are asymmetric and can be characterized by contrasting features in both time and space in China. Spatially, most areas in western China have experienced transitions from drying to wetting, while opposite changes have occurred in most areas of eastern China. Temporally, the transitions occurred earlier in western China compared to eastern China. Research into the asymmetric spatial characteristics of dry/wet conditions compensates for the inadequacies of previous studies, which focused solely on temporal evolution;at the same time, it remedies the inadequacies of traditional research on linear trends over centennial timescales. Analyzing the non-linear trend also provides for a more comprehensive understanding of the drying/wetting changes in China.

Effect of different drying methods on the taste and volatile compounds,sensory characteristics of Takifugu obscurus

Pufferfish is prone to deterioration due to abundant nutrients and high moisture content.Drying technology can extend the shelf life and enhance the flavor quality of aquatic products.The study investigated the effect of hot air drying(HAD),microwave vacuum drying(MVD)and hot air assisted radio frequency drying(HARFD)on the taste and volatile profiles of Takifugu obscurus.Different drying methods had significant influence on the color,rehydration,5’-nucleotides,free amino acids and volatile components(P<0.05).The results showed that HAD and HARFD could promote the flavor of T.obscurus by producing higher equivalent umami concentration(EUC)values,which were about two times of MVD group,and more pronounced pleasant odor according to sensory analysis.HAD is more appropriate for industrial application than HARFD and MVD considering the economic benefits.This study could provide a reference for the industrial application of drying T.obscurus.

Numerical Modelling of Drying Induced Cracks in Wood Discs Using the Extended Finite Element Method

Drying crack is a common phenomenon occurring during moisture discharge from wood,reducing efficient wood utilization.Drying crack is primarily caused by drying stress,and the reasonable methods for determining drying stress are sparse.In this study,the initiation and propagation of cracks during wood discs drying were simulated using the extended finite element method(XFEM).The distribution of drying stress and displacement was analyzed at different crack conditions based on the simulation results.This study aimed to solve the problem of the limitation of drying stress testing methods and provide a new idea for the study of wood drying stress.The numerical simulation results are found in good agreement with the experimental results,thus corroborating the feasibility of XFEM in modeling drying crack of wood discs.The stress concentration was observed at the crack tip region,while a minor stress was presented in the region of crack passing through,indicating that the crack formation process was also a process of releasing drying stress.Further,more energy was required to form double cracks in comparison with the single crack mode.

A Comparative Study of Different Drying Processes for a Deformable Saturated Porous Medium

Drying of a deformable saturated porous medium based on convective tempering is a novel method that can enhance energy efficiency and the quality of the dried product itself.In this experimental investigation,the performances of this specific technique are compared with those of a standard stationary drying process in terms of deformation,drying kinetics,moisture redistribution,and energy consumption.In particular,the response of a deformable saturated porous medium(Kaolin)is considered.The results are critically discussed pointing out advantages and drawbacks.

Investigation on microstructure evolution of clayey soils: A review focusing on wetting/drying process

Variability in moisture content is a common condition in natural soils.It influences soil properties significantly.A comprehensive understanding of the evolution of soil microstructure in wetting/drying process is of great significance for interpretation of soil macro hydro-mechanical behavior.In this review paper,methods that are commonly used to study soil microstructure are summarized.Among them are scanning electron microscope(SEM),environmental SEM(ESEM),mercury intrusion porosimetry(MIP)and computed tomography(CT)technology.Moreover,progress in research on the soil microstructure evolution during drying,wetting and wetting/drying cycles is summarized based on reviews of a large body of research papers published in the past several decades.Soils compacted on the wet side of op-timum water content generally have a matrix-type structure with a monomodal pore size distribution(PSD),whereas soils compacted on the dry side of optimum water content display an aggregate structure that exhibits bimodal PSD.During drying,decrease in soil volume is mainly caused by the shrinkage of inter-aggregate pores.During wetting,both the intra-and inter-aggregate pores increase gradually in number and sizes.Changes in the characteristics of the soil pore structure significantly depend on stress state as the soil is subjected to wetting.During wetting/drying cycles,soil structural change is not completely reversible,and the generated cumulative swelling/shrinkage deformation mainly derives from macro-pores.Furthermore,based on this analysis and identified research needs,some important areas of research focus are proposed for future work.These areas include innovative methods of sample preparation,new observation techniques,fast quantitative analysis of soil structure,integration of microstructural parameters into macro-mechanical models,and soil microstructure evolution charac-teristics under multi-field coupled conditions.

Hydraulic and volume change behaviors of compacted highly expansive soil under cyclic wetting and drying

The wide engineered application of compacted expansive soils necessitates understanding their behavior under field conditions.The results of this study demonstrate how seasonal climatic variation and stress and boundary conditions individually or collectively influence the hydraulic and volume change behavior of compacted highly expansive soils.The cyclic wetting and drying(CWD)process was applied for two boundary conditions,i.e.constant stress(CS)and constant volume(CV),and for a wide range of axial stress states.The adopted CWD process affected the hydraulic and volume change behaviors of expansive soils,with the first cycle of wetting and drying being the most effective.The CWD process under CS conditions resulted in shrinkage accumulation and reduction in saturated hydraulic conductivity(k sat).On the other hand,CWD under CV conditions caused a reduction of swell pressure while has almost no impact on k sat.An elastic response to CWD was achieved after the third cycle for saturated hydraulic conductivity(k sat),the third to fourth cycle for the volume change potential under the CV conditions,and the fourth to fifth cycle for the volume change potential under the CS conditions.Finally,both swell pressure(s s)and saturated hydraulic conductivity(k sat)are not fundamental parameters of the expansive soil but rather depend on stress,boundary and wetting conditions.

Modeling and simulation of solvent behavior and temperature distribution within long stick propellants with large web thickness undergoing drying

Drying is a complicated physical process which involves simultaneous heat and mass transfer in the removal of solvents inside propellants.Inappropriate drying techniques may result in the formation of a hard skin layer near the surface to block the free access of most solvent through for long stick propellants with large web thickness,which lead to lower drying efficiency and worse drying quality.This study aims to gain a comprehensive understanding of drying process and clarify the mechanism of the blocked layer near the propellant surface.A new three-dimensional coupled heat and mass transfer(3D-CHMT)model was successfully developed under transient conditions.The drying experiment results show that the 3DCHMT model could be applied to describe the drying process well since the relative error of the content of solvent between simulation and experiment values is only 5.5%.The solvent behavior simulation demonstrates that the mass transfer process can be divided into super-fast(SF)and subsequent minorfast(MF)stages,and the SF stage is vital to the prevention of the blocked layer against the free access for solvent molecules inside propellant grains.The effective solvent diffusion coefficient(Deff)of the propellant surface initially increases from 3.4×10^(-6)to 5.3×10^(-6)m^(2)/s as the temperature increases,and then decreases to 4.1×10^(-8)m^(2)/s at 60-100 min.The value of Deffof surface between 0-1.4 mm has a unique trend of change compared with other regions,and it is much lower than that of the internal at100 min under simulation conditions.Meanwhile,the temperature of the propellant surface increases rapidly at the SF stage(0-100 min)and then very slowly thereafter.Both the evolution of Deffand temperature distribution demonstrate that the blocked layer near the propellant surface has been formed in the time period of approximately 0-100 min and its thickness is about 1.4 mm.To mitigate the formation of blocked layer and improve its drying quality of finial propellant products effectively,it should be initially dried at lower drying temperature(30-40℃)in 0-100 min and then dried at higher drying temperature(50-60℃)to reduce drying time for later drying process in double base gun propellants.The present results can provide theoretical guidance for drying process and optimization of drying parameters for long stick propellants with large web thickness.

Diversity of Arbuscular Mycorrhizal Fungi Associated with Six Rice Cultivars in Italian Agricultural Ecosystem Managed with Alternate Wetting and Drying

Alternate wetting and drying(AWD)system,in which water has been reduced by approximately 35%with an increased occurrence of beneficial arbuscular mycorrhizal(AM)symbiosis and no negative impact on rice yield,was proposed to utilize water and nutrients more sustainable.In this study,we selected six rice cultivars(Centauro,Loto,Selenio,Vialone nano,JSendra and Puntal)grown under AWD conditions,and investigated their responsiveness to AM colonization and how they select diverse AM taxa.In order to investigate root-associated AM fungus communities,molecular cloning-Sanger sequencing on small subunit rDNA data were obtained from five out of the six rice cultivars and compared with Next Generation Sequencing(NGS)data,which were previously obtained in Vialone nano.The results showed that all the cultivars were responsive to AM colonization with the development of AM symbiotic structures,even if with differences in the colonization and arbuscule abundance in the root systems.We identified 16 virtual taxa(VT)in the soil compartment and 7 VT in the root apparatus.We emphasized that the NGS analysis gives additional value to the results thanks to a more in-depth reading of the less represented AM fungus taxa.

Insight into the effect of gel drying temperature on the structure and desulfurization performance of ZnO/SiO_(2)adsorbents

A series of ZnO/SiO_(2) adsorbents were prepared by a sol-gel method using tetraethyl orthosilicate,ethylene glycol(EG)and nitrates as precursors.The effect of gel drying temperature on the structure and desulfurization performance of the adsorbents were investigated in detail.It is found that the low drying temperature led to a weak interaction among EG,Si AOH/H_(2)O and the nitrates in the gel system,which caused the oxidation of EG by NO3-and formed zinc glyoxylate complex during the gel calcination process,whereas this oxidation process also occurred at a high drying temperature during the gel drying process.The formed zinc glyoxylate complex promoted the generation of monodentate carbonate on the surface of Zn O,which resulted in the inferior desulfurization performance of adsorbents despite they have smaller Zn O nanoparticles.The gel dried at 120°C formed the hydrogen bonds between EG and Si AOH/H_(2)O and a strong interaction between zinc oxo-clusters and NO3-was also found in the gel system,which avoided the oxidation of EG by NO3-during the preparation process and the Zn O nanoparticles with sizes of 6 nm were formed by a combustion method.The adsorbent affords a highest sulfur capacity of 104.9 mg·g^(-1) in this case.In addition,the gel drying temperature has a significant influence on the textural properties of the adsorbents except their surface area.

Microwave Drying of Scots Pine Lumber:Structure Changes,Its Effect on Liquid Permeability

Microwave(MW)drying method was adopted to enhance the liquid permeability of Scots pine lumber.Structure changes were characterized by stereoscope microscope,scanned electron microscope(SEM)and transmission electron microscope(TEM)examination.Pore parameters before and after MW treatment were detected by mercury intrusion porosimetry(MIP)method,and the effect of structure changes on liquid permeability were analyzed.As stereoscope microscope,SEM and TEM examination results showed,macro and micro checks mainly developed at intercellcular of tracheids,intercellular of ray parenchyma and tracheid,while these checks extend main along the radial-longitudinal plane.Pit border destruction,aspirated pits’orus translocation and micro-checks in tracheid cell wall were also observed.MIP test shown that pore volume and pore area increased as macro and micro checks generated to form new cavities.Microstructure changes would increase the quantity of pores or enlarge the pore diameter.Liquid flow pathways increased as macro and micro checks generated,aspirated pits reopened to form new pathways;liquid flow efficiency improved as porosity,pore volume and pore diameter increased which facilitated the liquid flow.

Fine Characterization and Analysis of Drying Strain of the ELM Board via DIC Technology

In this paper,the occurrence and development mechanism of strain on the cross-section during the wood drying is explored.Therefore,strain regularity on the cross-section of 50 mm thickness elm(Ulmus rubra)board at the temperature of 40℃and 80℃is detected via digital image correlation technology.Hence,the difference between tangential and radial strain at surface and core layers was denoted.The results showed that strain distribution in the width direction of the board is uneven.Moreover,a large drying shrinkage strain occurs at the near-core layer,while the maximum strain difference reaches 4.08%.Hence,the surface of the board is cracked along the thickness direction.The radial strain of the board is higher than the tangential strain in the early stage of drying,while these strains are reversed in the later stage of drying.The temperature is related to the difference between the tangential and radial strains of the elm board.These differences at the core layer are larger than those of the surface layer.The conducted research results provide a theoretical basis for process optimization.

Drying kinetics of soy protein isolate-corn starch film during preparation and its moisture adsorption characteristics during storage

To better understand the mass transfer process of moisture in the soy protein isolate-corn starch(SPI-CS)films during preparation and storage process,the drying kinetics model of SPI-CS films with different formation conditions during the drying process and the moisture adsorption characteristics of the SPI-CS films under different humidity conditions were investigated.Within the range of experimental conditions,the moisture migration rule in the SPI-CS films during the drying preparation was combined with the Page model which was expressed as MR=exp(-kt^(n)).It was found that the adsorption equilibrium needed shorter time(about 3 h)when the SPI-CS films existed in the environment with lower humidity(RH<54%).Additionally,the secondorder adsorption kinetic equation was successful to describe the moisture adsorption characteristic of the SPICS films during storage under different humidity conditions.

Influence of Sorbent Type on Drying Efficiency, Production Costs and Nutritional Values of Mango By-Products Feeds for Livestock

The aim of the study was to determine the best food absorbents between wheat, rice and maize bran and palm kernel cake, from a technical and economic point of view, in order to make a better recommandation for their use in the production process of food based on mango by-products (peels, peels + pulp). To this end, series of 18 kg of fresh feed were prepared and spread out in a stall for sun-drying using a randomized Fisher system. Preparations were made using either mango peels (75%) + absorbent (25%) or pulp + mango peels (67%) + sorbent (33%). The results show that mango Peel feed loses more water (WL) with lover production yields (PY), higher mango incorporation rates into dry feed (MRI), longer drying times (UDT) and lower production costs (CPkgPD) than mango peel + pulp. The average DM, MAT, ADF and NDF fiber contents were almost equal to those of mango peels + pulp feed. The average Crude Fiber (CF) (25.13%) and DEp (2839 kcal/kgDM) contents were higher for mango skin feed than for mango skin + pulp feed, at 8.59% and 2536 for MAT and DEp respectively. Mango peels + wheat bran (PSB25) and whole mango (MESB33) feeds recorded the highest and almost equal levels of TCP, NDF and MM. Production costs per kg of feed dry mater (CPkgDM) for feed produced at 25% were on average 33% higher than for whole mango (WM) feed. Excluding mango raw material, palm kernel meal (PK), rice bran (RB), maize bran (MB) and wheat bran (WB) can be ranked 1st, 2nd, 3rd and 4th in terms of cumulative performance of production parameters. Producers can then choose the type of sorbent they wish to use according to this ranking and the local availability of the sorbent. These feeds can be used for both ruminants and monogastrics, but are better suited to ruminant feeding due to their high fiber content.

Natural Solar Drying and Charcoal Production by Pyrolysis of Empty Shells of Cocoa Pods Using a Carbonisation Stove Fitted with a Chimney

The world’s production of cocoa highly has grown since 1960.In West Africa,the production reached about 3,000,000 tons in 2012.More than 50%of the world’s production of cocoa comes nowadays from Côte d’Ivoire and Ghana and Côte d’Ivoire is the biggest producer.After harvesting,the empty shells,considered as non-useful wastes,are abandoned in the fields where they become a source of pollution.That yields millions of tons of biomass that can be converted into charcoal,instead of being sources of pollution.In the present work,the drying kinetics of the empty wet shells were studied.Then,charcoal production by pyrolysis of those empty shells of cocoa pods was performed,using a carbonisation stove fitted with a chimney.The study showed that the empty shells have a high moisture content.The different phases of the drying were observed.The study compared the drying rates and the diffusion coefficients of a small sample and a big sample.Two experiences of carbonisation of the empty shells were successfully carried out.For the first experiment,the pyrolysis temperatures were recorded and the charcoal mass efficiency calculated.For the second experiment,the temperatures were higher and the result was colored charcoals.The colorations disappeared after some hours.

Optimization of Process Parameters of Continuous Microwave Drying Raspberry Puree Based on RSM and ANN-GA

To improve drying uniformity and anthocyanin content of the raspberry puree dried in a continuous microwave dryer,the effects of process parameters(microwave intensity,air velocity,and drying time)on evaluation indexes(average temperature,average moisture content,average retention rate of the total anthocyanin content,temperature contrast value,and moisture dispersion value)were investigated via the response surface method(RSM)and the artificial neural network(ANN)with genetic algorithm(GA).The results showed that the microwave intensity and drying time dominated the changes of evaluation indexes.Overall,the ANN model was superior to the RSM model with better estimation ability,and higher drying uniformity and anthocyanin retention rate were achieved for the ANN-GA model compared with RSM.The optimal parameters were microwave intensity of 5.53 W•g^(-1),air velocity of 1.22 m·s^(-1),and drying time of 5.85 min.This study might provide guidance for process optimization of microwave drying berry fruits.