Necessity and feasibility of improving the residual resistance factor of polymer flooding in heavy oil reservoirs

The efficiency of water flooding in heavy oil reservoirs would be improved by increasing the viscosity of the displacing phase, but the sweep efficiency is not of significance due to the low mobility of the vicious oil. On the basis of mobility control theory, increasing the residual resistance factor not only reduces the water-oil mobility ratio but also decreases the requirement for viscosity enhancement of the polymer solution. The residual resistance factor caused by hydrophobic associating polymer solution is higher than that caused by polyacrylamide solution in brine containing high concentrations of calcium and magnesium ions. The results of numerical simulations show that the polymer flooding efficiency improved by increasing the residual resistance factor is far better than that by only increasing solution viscosity. The recovery factor of heavy oil reservoirs （70 mPa·s） can be enhanced by hydrophobic associating polymer solution of high residual resistance factor （more than 3） and high effective viscosity （24 mPa·s）. Therefore, increasing the residual resistance factor of the polymer solution not only decreases the requirement for the viscosity of polymer solution injected into heavy oil reservoirs but also is favorable to enhanced oil recovery during polymer flooding.

Hydrodynamic resistance of pore–throat structures and its effect on shale oil apparent permeability

Oil transport is greatly affected by heterogeneous pore–throat structures present in shale.It is therefore very important to accurately characterize pore–throat structures.Additionally,it remains unclear how pore–throat structures affect oil transport capacity.In this paper,using finite element(FE)simulation and mathematical modeling,we calculated the hydrodynamic resistance for four pore–throat structure.In addition,the influence of pore throat structure on shale oil permeability is analyzed.According to the results,the hydrodynamic resistance of different pore throat structures can vary by 300%.The contribution of additional resistance caused by streamline bending is also in excess of 40%,even without slip length.Fur-thermore,Pore–throat structures can affect apparent permeability by more than 60%on the REV scale,and this influence increases with heterogeneity of pore size distribution,organic matter content,and organic matter number.Clearly,modeling shale oil flow requires consideration of porous–throat structure and additional resistance,otherwise oil recovery and flow capacity may be overestimated.

Temperature-resistant and salt-tolerant mixed surfactant system for EOR in the Tahe Oilfield

A new temperature-resistant and salt-tolerant mixed surfactant system(referred to as the SS system)for enhancing oil recovery at the Tahe Oilfield(Xinjiang,China)was evaluated.Based on the analysis of the crude oil,the formation water and rock components in the Tahe Oilfield,the long-term thermal stability,salt tolerance and the ability to change the wettability,interfacial activity and oil washing efficiency of the mixed surfactant system were studied.The system contains the anionic surfactant SDB and another cationic surfactant SDY.When the total mass concentration of the SS solution is 0.15 wt%,m(SDB)/m(SDY)ratio is 1 to 1,and excellent efficiencies are achieved for oil washing for five kinds of Tahe Oilfield crude oils(more than 60%).In addition,after adding cationic surfactant,the adsorption capacity of the surfactant is further reduced,reaching 0.261 mg/g.The oil displacement experiments indicate that under a temperature of 150°C and a salinity of 24.6×104 mg/L,the SS system enhances the oil recovery by over 10%after water flooding.The SS anionic–cationic surfactant system is first presented in the open literature that can be successfully applied to obtain predictions of Tahe Oilfield carbonate reservoirs with a high temperature and high salinity.

Breeding of a New High-yield, High-oil and Web Blotch-resistant Big Peanut Variety Shanghua 511

Shanghua 511 is a high-yield, high-oil and web blotch-resistant big peanut variety bred by the Shangqiu Academy of Agriculture and Forestry Sciences through sexual hybridization （Yuhua 18♀×Shangyan 9658♂）. In the wheat-peanut interplanting regional experiment conducted in Henan Province during 2012-2013, the average pod and seed yield of Shanghua 511 were 5906.19 and 4149.3 kg/hm2, respectively. In the wheat-peanut interplanting production experiment conducted in Henan Province in 2013, the average pod and seed yield of Shanghua 511 were 6036.45 and 4309.50 kg/hm2, respectively. In the kernels of Shanghua 511, the contents of crude fat, oleic acid and linoleic acid were 56.62%, 44.9% and 33.4% respectively, and the oleic/linoleic acid ratio was 1.34. This variety had high resistance to web blotch and medium resistance to leaf spot, viral diseases, root rot and collar rot. The 100-pod weight, 100-kernel weight, shelling percentage and growth period of Shanghua 511 were 270.6, 110.9 g, 70.6% and 120 d, respectively. Shanghua 511 passed the approval of Henan Provincial Crop Variety Approval Committee in August, 2015, and is suitable for spring sowing and wheat interplanting in the surrounding area of Henan Province and the area to the north of Huaihe River.

Synthesis of temperature-resistant and salttolerant surfactant SDB-7 and its performance evaluation for Tahe Oilfield flooding (China)

In order to improve the enhanced oil recovery of high-temperature and high-salt oilfields, a novel temperature-resistant and salt-tolerant surfactant （denoted as SDB-7） was synthesized and evaluated for the Tahe Oilfield （Xinjiang, China）, which is representative of high-temperature and high-salt oilfields. It has a central reservoir temperature of 140 ℃ and salinity of 22.6× 10^4 mg/L. The temperature-resistant and salt-tolerant performance, interfacial activity, oil displacement efficiency, aging properties, and adsorption properties of the synthesized surfactant were evaluated for Tahe Oilfield flooding. The results showed that the SDB-7 was temperature-resistant and salt-tolerant capacity of 140 ℃ and 22.6×10^4 rag/ L, respectively, oil displacement efficiency under static condition of 84%, and adsorption loss of 0.4 mg/ g （less than 1 mg/g-oil sand）. In the heat aging experiment （under the temperature of 140 ℃ for 60 days）, the oil-water interracial tension and oil displacement efficiency of SDB-7 were almost unchanged. The oil displacement experiments showed that, under the temperature of 140 ℃ and the salinity of 22.6× 10^4 mg/L, the surfactant SDB-7 can enhance oil recovery by 14.5% after water flooding,suggesting that SDB-7 has a promising application in high temperature and high salinity （HT/HS） reservoir.

Antimicrobial activity of some essential oils against oral multidrugresistant Enterococcus faecalis in both planktonic and biofilm state

Objective:To evaluate some essential oils in treatment of intractable oral infections,principally caused by hiofilm of multidrug-resistant Enterococcus faecalit(E.faecalis),such as persistent endodontic infections in which their treatment exhibits a real challenge for dentists.Methods:Ten chemically analyzed essential oils by gas chromatography-mass spectrometry were evaluated for antimicrobial activity against sensitive and resistant clinical strains of E.faecalit in both planktonic and hiofilm state using two methods,disk diffusion and broth microdilution.Results:Studied essential oils showed a good antimicrobial activity and high ability in E.faecalit biofilm eradication,whether for sensitive or multidrug-resistant strains,especially those of Origanum glandulosum and Thymbra capitata with interesting minimum inhibitory concentration,biofilm inhibitory concentration,and biofilm eradication concent ration values which doesn't exceed 0.063%,0.75%,and 1.5%,respectively.Conclusions:Findings of this study indicate that essential oils extracted from aromatic plants can be used in treatment of intractable oral infections,especially caused by biofilm of multidrugresistant E.faecalis.

Antibacterial Activity of Essential Oil from <i>Citrus aurantifolia</i>(Christm.) Swingle Peels against Multidrug-Resistant Bacterial Isolates

The study investigated the antibacterial activity of essential oil from the peel of Citrus aurantifolia against eleven multidrug-resistant (MDR) bacterial isolates of clinical origin. The Kirby-Bauer disc diffusion method was used to determine the antibiotic resistance profile of the isolates. Essential oil (EO) from the peels of lime purchased at a market in Ile-Ife was extracted by the hydro-distillation method, while the sensitivity of the isolates to EO was done via agar well diffusion method. The minimum inhibitory and minimum bactericidal concentrations (MIC and MBC) of the EO against the tested isolates were determined following standard methods. All the tested isolates exhibited multidrug resistance (MDR) characteristics. The multiple antibiotics resistant indexes (MARI%) for Gram-positive bacterial isolates ranged between 70% and 100% while that of Gram-negative was 100%. The yield of EO was 1% and the EO demonstrated activities at 25%, 50% and 100% v/v against the MDR bacterial isolates. The activity of EO was mostly not significantly different at the same concentration for all the isolates, and at different concentrations for each of the isolates. The MIC range for Gram-negative and Gram-positive isolates was between 0.195% to 3.125% v/v and 0.39% to 3.125% respectively while the range was between 1.563% to 3.125% and 0.781% to 6.250% v/v for MBC respectively. The study showed that EO from the peel of lime fruits demonstrated excellent in vitro antibacterial activity against MDR bacterial isolates. This potential can be further explored as an alternative for the treatment and management of infections caused by MDR bacterial isolates.

High Performance Oil Resistant Rubber

Blending of polymers has gained much interest due to the fact that, it can be used to produce new polymeric materials with specific properties suitable for some special applications. The blends from acrylonitrile butadiene rubber (NBR), chloroprene rubber (CR) and polyvinyl chloride (PVC) has been designed for products working in contact with oils. The characteristics of the designed blends either binary blends (NBR/PVC or PVC/CR) or ternary blends (NBR/ PVC/CR) were investigated by rheological properties, mechanical analysis and swelling in oil and toluene. It was found that the incorporation of PVC in the blend compositions leads to the decrease in degree of swelling, the penetration rate and the average diffusion coefficient. On the other hand the ultimate tensile strength (UTS), the hardness and strain energy were increased. This was attributed to the plastic nature of PVC, beside its additional behavior as filler. The crosslinking density in the blend vulcanizates under investigations was determined by Flory-Rehner and Mooney-Rivlin [Stress/Strain] equations. The higher values of crosslinking density determined by Mooney-Rivlin can be attributed to the additional physical crosslinks (e.g. entanglements etc), beside the chemical crosslinks determined by swelling in toluene. This study showed that NBR/PVC blends are characterized with high performance oil resistant, which can be recommended to automotive industry.

Response simulation and theoretical calibration of a dual- induction resistivity LWD tool

In this paper, responses of a new dual-induction resistivity logging-while-drilling （LWD） tool in 3D inhomogeneous formation models are simulated by the vectorfinite element method （VFEM）, the influences of the borehole, invaded zone, surroundingstrata, and tool eccentricity are analyzed, and calibration loop parameters and calibrationcoefficients of the LWD tool are discussed. The results show that the tool has a greater depthof investigation than that of the existing electromagnetic propagation LWD tools and is moresensitive to azimuthal conductivity. Both deep and medium induction responses have linearrelationships with the formation conductivity, considering optimal calibration loop parametersand calibration coefficients. Due to the different depths of investigation and resolution, deepinduction and medium induction are affected differently by the formation model parameters,thereby having different correction factors. The simulation results can provide theoreticalreferences for the research and interpretation of the dual-induction resistivity LWD tools.

A static resistance model and the discontinuous pattern of hydrocarbon accumulation in tight oil reservoirs

In exploration for tight oil, the content and saturation of hydrocarbon in the tight reservoir is a key factor for evaluating the reserve. Therefore, it is necessary to study the geological history of hydrocarbon accumulation and the tight oil charging process. However, kinetic models used for petroleum development are not applicable for petroleum exploration. In this study, a static resistance model[ is proposed after analyzing resistances in ultra-slow flow in porous media. Using this model, the disco^atinuous pattern of oil charging is reproduced through incompressible Navier-Stokes equations, the phase field method and the finite element method. This study also explains macroscopic percolation behavior with microscopic flow mechanisms and discusses some issues in ultra-slow flow in a micro/nano pore-throat network. The resistance analysis reveals that capillary resistance and dissipation resistance are dominant factors in the mechanism of oil accumulation in tight reservoirs. Numerical simulations show that pressure thresholds exist and result in discontinuous oil charging. Generally, it is proven that the static model is more applicable than kinetic models in describing oil accumulation in tight reservoirs.

Synthesis of a Novel Core-shell Type Acrylic-polyurethane Hybrid Emulsion Containing Siloxane and Fluorine as well as Water and the Oil Resistances of Cured Film

Siliconated polyurethane （Si-PU） was synthesized using isophorone diisocyanate （IPDI）, hydroxybutyl-terminated polydimethylsiloxane （PDMS）, polytetramethylene ether glycol （PTMG）, polypropylene glycol （PPG）, 1,6-hexanediol （HDO）, dimethylol propionic acid （DMPA） and triethylamine （TEA）. Based on butyl acrylate （BA）, 2, 2, 2-trifluoroethylmethacrylate （TFEMA） and Si-PU as a seed emulsion, a novel core-shell type acrylic-polyurethane hybrid emulsion, containing siloxane and fluorine （F-Si-PU）, was prepared by seeded emulsion polymerization. The contents of siloxane and fluorine were determined according to the feed ratio. Fourier transform infrared spectroscopy （FTIR） was used to identify the chain structures of Si-PU and F-Si-PU. Investigation of transmission electron microscopy （TEM） confirmed the core-shell structure of F-Si-PU emulsion. Measurement results of water contact angle and the swelling ratio in water and n-octane for cured film showed that the water and the oil resistances for F-Si-PU had been significantly improved at a suitable content of fluorine and siloxane.

Resistance Characteristics of Hydraulic Oil through Isodiametric T-type Duct with Sharp Corners

Rational determination and reduction of local energy loss of oil flow at pipe junctions are of important significance to improve hydraulic pipeline＇s work efficiency, especially for complex hydraulic pipeline connected by isodiametric T-type ducts with sharp comers to get combined and divided flow. From this point of view, the formulae of resistance loss for combined flow and divided flow through isodiametric T-type duct with sharp comers as well as the correlations of resistance loss coefficients in the branches of the duct are derived using energy method. On this basis, resistance characteristics of hydraulic oil in the duct are obtained by numerical simulation of different flow modes, which are commonly applied in hydraulic pipelines, using computational fluid dynamics （CFD） method, and the reasons for the resistance loss are analyzed based on the pressure change mechanism in the flow field. A part of simulation results was validated with the reference data. The research shows that for combined flows the resistance loss of symmetrical is lower than that of unsymmetrical to obtain low speed in common branch, but to gain high speed is quite the contrary, for divided flows, the symmetrical is always a reasonable choice to reduce resistance loss. These conclusions can be applied to optimize the design of hydraulic pipeline.

Strength and chloride resistance of blended Portland cement mortar containing palm oil fuel ash and fly ash

This paper presented a study on the strength and chloride resistance of mortars made with ternary blends of ordinary Portland cement （OPC）, ground palm oil fuel ash （POA）, and classified fly ash （FA）. The mortar mixtures were made with Portland cement type I containing 0-40wt% FA and POA. FA and POA with 1wt%-3wt% retained on a sieve No.325 were used. The compressive strength and rapid chloride penetration depth of mortars were determined. The results reveal that the use of ternary blended cements produces good strength mortars. The use of the blend of FA and POA also produces high strength mortars and excellent resistance to chloride penetration owing to the synergic effect of FA and POA. A mathematical analysis and two-parameter polynomial model were presented to predict the compressive strength. The mathematical model correlated well with the experimental results. The computer 3-D graphics of strength of the ternary blended mortars were also constructed and could be used to aid the understanding and the proportioning of the blended system.

Dual alloying improves the corrosion resistance of biodegradable Mg alloys prepared by selective laser melting

Mg alloys have been regarded as revolutionary metallic biomaterials for biodegradable bone implants,but their applications are mainly blocked by the too rapid degradation in physiological environment.This study explores the dual alloying effects of Mn and/or Sn on the performance of Mg alloys prepared by selective laser melting.The observed microstructure indicated remarkable refinement of both the grains and intermetallic phases in the Mn-and/or Sn-containing alloys during the rapid solidification process.Moreover,approximately a half decrease in corrosion rate was observed for AZ61-0.4Mn-0.8Sn alloy with respect to AZ61 alloy.The improved corrosion behavior was primarily due to the enhanced protective effects of surface layers,in which Mn-and/or Sn-rich phases acted as a helpful barrier against medium penetration and thereby alleviated the current exchange with the matrix.In addition,the solute Mn and/or Sn positively shifted the corrosion potential,which also brought about a better corrosion resistance.Furthermore,the strength and hardness of the alloys were also effectively improved and comparable to those of cortical bone.This could be ascribed to the dissolved Mn and/or Sn atoms and the finely dispersed intermetallic phases,which might cause lattice distortion and precipitation hardening.Besides,the Mn-and/or Sn-containing alloys showed good cytocompatibility as indicated by the normal morphology and increased viability of MG-63 cells.These findings suggest that the developed AZ61-Mn-Sn alloy is a promising candidate for biodegradable bone implants.

Electro-optical dual modulation on resistive switching behavior in BaTiO3/BiFeO3/TiO2 heterojunction

The novel BaTiO3/BiFeO3/TiO2 multilayer heterojunction is prepared on a fluorine-doped tinoxide(FTO) substrate by the sol–gel method. The results indicate that the Pt/Ba TiO3/BiFeO3/TiO2/FTO heterojunction exhibits stable bipolar resistive switching characteristic, good retention performance, and reversal characteristic. Under different pulse voltages and light fields, four stable resistance states can also be realized. The analysis shows that the main conduction mechanism of the resistive switching characteristic of the heterojunction is space charge limited current(SCLC) effect. After the comprehensive analysis of the band diagram and the P–E ferroelectric property of the multilayer heterojunction, we can deduce that the SCLC is formed by the effect of the oxygen vacancy which is controlled by ferroelectric polarizationmodulated change of interfacial barrier. And the effective photo-generated carrier also plays a regulatory role in resistance state(RS), which is formed by the double ferroelectric layer Ba TiO3/BiFeO3 under different light fields. This research is of potential application values for developing the multi-state non-volatile resistance random access memory(RRAM) devices based on ferroelectric materials.

Water and Oil Resistance of Special Paperboard for Petroleum Packaging

The influence of different coating formulas and times on the water and oil resistance of paperboard was studied. The water and oil resistance of paperboard coated with a modified butadiene-styrene copolymer latex and fluorinated anion grease-proof agent was better than that coated with modified butadiene-styrene copolymer latex,where the modified butadiene-styrene copolymer latex was used as the pre-coating substrate and the F1516 fluorinated grease-proof agent was used as the top coating material. By coating modified butadiene-styrene copolymer latex with 30% solid content and F1516 fluorinated grease-proof agent with 24% solid content,the oil resistance of paperboard could reach anti-oil grade 12 and the water resistance could increased by98. 64%( compared with the base paperboard without any coating treatment).

Pore structure differences of the extra-low permeability sandstone reservoirs and the causes of low resistivity oil layers: A case study of Block Yanwumao in the middle of Ordos Basin, NW China

The influence of pore structure difference on rock electrical characteristics of reservoir and oil reservoir was analyzed taking Triassic Chang 6 reservoir in Block Yanwumao in the middle of Ordos Basin as an example. The relationship between the pore structure difference and the low resistivity oil layer was revealed and demonstrated through core observation, lab experiments, geological research, well log interpretation and trial production etc. The results show that there were two kinds of oil layers in Chang 6 oil layer set, normal oil layer and low resistivity oil layer in the region, corresponding to two types of pore structures, pore type mono-medium and micro-fracture-pore type double-medium; the development of micro-fracture changed greatly the micro-pore structure of the reservoir, and the pore structure difference had an important influence on the rock electrical characteristics of the extra-low permeability sandstone reservoir and oil reservoir; the normal oil layers had obvious characteristics of pore-type mono-medium, and were concentrated in Chang 61, Chang 6232 and Chang 62; the low resistivity oil layers had obvious characteristics of micro-fracture-pore type double-medium, which were mainly distributed in Chang 612 and Chang 63. The mud filtrate penetrated deep into the oil layers along the micro-cracks, leading to sharp reduction of resistivity, and thus low resistivity of the oil layer; the low resistivity oil layers had better storage capacity and higher productivity than the normal oil layers.

Electrospinning organic solvent resistant preoxidized poly(acrylonitrile)nanofiber membrane and its properties

A high performance preoxidized poly(acrylonitrile)(O-PAN)nanofiber membrane with excellent solvent resistance,thermal stability and flexibility was fabricated by the preoxidation of electrospun PAN nanofiber membrane.The performance of resultant O-PAN nanofiber membrane was optimized by altering the PAN concentration and preoxidation temperature.The results showed that the O-PAN nanofiber membrane which made from PAN concentration of 14%(mass)and preoxidation temperature of 250.0
℃ have a more optimal comprehensive performance.In the long-term separation test of SiO2 particle(1 μm)in DMAc suspension,the permeate flux of O-PAN nanofiber membrane stabilized at 227.91 L·m^(-2)·h^(-1)(25
℃,0.05 MPa)while the SiO2 rejection above 99.6%,which showed excellent solvent resistance and separation performance.In order to further explore the application of the O-PAN nanofiber membrane,the OPAN nanofiber membrane was treated with fluoride and used in oil/water separation process.The O-PAN nanofiber membrane after hydrophobic treatment showed excellent hydrophobicity and good oil/water separation performance with the permeate flux about 969.59 L·m^(-2)·h^(-1)while the separation efficiency above 96.1%.The O-PAN nanofiber membrane exhibited a potential application prospect in harsh environment separation.

Enhanced Water Resistance Performance of Castor Oil—Based Waterborne Polyurethane Modified by Methoxysilane Coupling Agents via Thiol-Ene Photo Click Reaction

Nowadays,waterborne polyurethanes(WPUs)prepared from renewable resources has attracted more and more attention.However,due to its structure,the prepared films easily swells in water and greatly affects the application range of WPUs.Therefore,solving the problem of water resistance is a way to improve the application range of WPUs.In this study,a series of WPU dispersions were prepared using castor oil as the bio-based polyol.Besides,the thiol-ene photo click reaction was carried out on the WPU films for silane modification.The effect of the silane modification on the chemical structures of the WPU dispersions and the properties of the WPU films was investigated and discussed.The results revealed that the WPU dispersions had a smaller particle size and potential,showing excellent stability.In addition,the modified WPU films showed highly water resistance which 72 h water absorption could be reduced to 1.94%and the contact angle was up to 99.34?.Moreover,the modified WPU films also exhibited excellent solvent resistance(in acid and salt solution)and thermal stability.This study can provide a new way to improve the water-resistance,hydrophobicity,and thermal stability of bio-based waterborne polyurethane for potential application in painting,adhesives and inks.

Test method and experimental research on resistance of oil shale under high temperature

Heating the oil shale by current underground to accomplish in-situ transformation process, is a viable direction. The electrical properties of oil shale under different temperatures, especially the resistance, become important. Charging oil shale underground to heat oil shale till kerogen's decomposition temperature, then crude oil and other gases can be generated. The resistance of the oil shale samples was measured by Direct Current (DC) quadripole method to find out the variation rules of resistance value. In the experiments, oil shale presented its semiconductor property. When heated till 350℃-450℃, its resistance changed greatly, optional for heating and cracking. The porosity, oil content, media and composition affected the resistance largely.